Commission Regulation (EU) No 1304/2014 of 26 November 2014 on the technical specification for interoperability relating to the subsystem ‘rolling stock — noise’ amending Decision 2008/232/EC and repealing Decision 2011/229/EU Text with EEA relevance
Modified by
  • Commission Implementing Regulation (EU) 2019/774of 16 May 2019amending Regulation (EU) No 1304/2014 as regards application of the technical specification for interoperability relating to the subsystem rolling stock — noise to the existing freight wagons(Text with EEA relevance), 32019R0774, May 27, 2019
Commission Regulation (EU) No 1304/2014of 26 November 2014on the technical specification for interoperability relating to the subsystem rolling stock — noise amending Decision 2008/232/EC and repealing Decision 2011/229/EU(Text with EEA relevance)
Article 1This Regulation lays down the technical specification for interoperability (TSI) relating to the "rolling stock — noise" subsystem of the rail system in the Union, as set out in the Annex.
Article 2The TSI shall apply to the rolling stock which falls within the scope of Commission Regulation (EU) No 1302/2014Commission Regulation (EU) No 1302/2014 of 18 November 2014 concerning a technical specification for interoperability relating to the "rolling stock — locomotives and passenger rolling stock" subsystem of the rail system in the European Union (See page 228 of this Official Journal). and Commission Regulation (EU) No 321/2013Commission Regulation (EU) No 321/2013 of 13 March 2013 concerning the technical specification for interoperability relating to the subsystem "rolling stock — freight wagons" of the rail system in the European Union and repealing Decision 2006/861/EC (OJ L 104, 12.4.2013, p. 1)..
Article 3Within six months of the entry into force of this Regulation, Member States shall notify the Commission of all agreements containing requirements relating to noise emission limits, provided they were not already notified under Commission Decisions 2006/66/ECCommission Decision 2006/66/EC of 23 December 2005 concerning the technical specification for interoperability relating to the subsystem rolling stock — noise of the trans-European conventional rail system (OJ L 37, 8.2.2006, p. 1). or 2011/229/EU.The agreements to be notified shall be:(a)national agreements between the Member States and railway undertakings or infrastructure managers, agreed on either a permanent or a temporary basis and necessitated by the specific or local nature of the intended transport service;(b)bilateral or multilateral agreements between railway undertakings, infrastructure managers or safety authorities which deliver significant levels of local or regional interoperability;(c)international agreements between one or more Member States and at least one third country, or between railway undertakings or infrastructure managers of Member States and at least one railway undertaking or infrastructure manager of a third country which deliver significant levels of local or regional interoperability.
Article 4The procedures for assessment of conformity, suitability for use and EC verification set out in Section 6 of the Annex to this Regulation shall be based on the modules defined in Commission Decision 2010/713/EUCommission Decision 2010/713/EU of 9 November 2010 on modules for the procedures for assessment of conformity, suitability for use and EC verification to be used in the technical specifications for interoperability adopted under Directive 2008/57/EC of the European Parliament and of the Council (OJ L 319, 4.12.2010, p. 1)..
Article 51.With regard to specific cases listed in point 7.3.2 of the Annex, the conditions to be met for the verification of the essential requirements set out in Annex III to Directive (EU) 2016/797 shall be those laid down in point 7.3.2 of the Annex or by national rules in force in the Member State which is part of the area of use of the vehicles covered by this Regulation.2.Within six months of the entry into force of this Regulation, each Member State shall inform the Commission and the Member States about:(a)the technical rules referred to in paragraph 1;(b)the conformity assessment and verification procedures to be carried out in application of the technical rules referred to in paragraph 1;(c)the bodies designated to carry out the conformity assessment and verification procedures with respect to the national rules relating to the specific cases set out in point 7.3.2 of the Annex.
Article 5aFrom 8 December 2024, wagons within the scope of Regulation (EU) No 321/2013 which are not covered by point 7.2.2.2 of the Annex to this Regulation shall not be operated on the quieter routes.
Article 5bA "quieter route" means a part of the railway infrastructure with a minimum length of 20 km on which the average number of daily operated freight trains during the night-time as defined in national legislation transposing Directive 2002/49/EC of the European Parliament and of the CouncilDirective 2002/49/EC of the European Parliament and of the Council of 25 June 2002 relating to the assessment and management of environmental noise (OJ L 189, 18.7.2002, p. 12). was higher than 12. The freight traffic in the years 2015, 2016 and 2017 shall be the basis for the calculation of that average number. In case the freight traffic due to exceptional circumstances diverges in a given year from that average number by more than 25 %, the Member State concerned can calculate the average number on the basis of the remaining two years.
Article 5c1.Member States shall designate quieter routes in accordance with Article 5b and the procedure set out in Appendix D.1 of the Annex. They shall provide the European Union Agency for Railways ("the Agency") with a list of quieter routes six months after the date of publication of this Regulation at the latest. The Agency shall publish those lists on its website.2.Member States shall update the list of quieter routes at least every five years after 8 December 2024, following the procedure set out in Appendix D.2 of the Annex.
Article 5dBy 31 December 2028, the Commission shall evaluate the implementation of the quieter routes, in particular regarding the progress of retrofitting of wagons and the impact of the introduction of quieter routes on the overall noise exposure of the population and competitiveness of the rail freight sector.
Article 5eBy 30 June 2020, the Commission shall issue a report regarding operations with wagons equipped with composite brake blocks in Nordic winter conditions, based on evidence gathered by the Agency, national safety authorities and rail companies. In particular, this report shall contain an assessment of the safety and braking performance of such wagons and existing or potential operational and technical measures applicable in Nordic winter conditions. The report shall be made public.If the report provides evidence that the use of such wagons in Nordic winter conditions poses safety issues that cannot be addressed by operational and technical measures without severe adverse impact on rail freight operations, the Commission shall propose amendments to this TSI to address those issues while preserving cross border freight traffic to and from affected Nordic regions. In particular, the proposal may if necessary include an exemption permitting the continued operation on quieter routes throughout the Union of a limited number of wagons used frequently in such cross border freight traffic, and any operational restrictions appropriate to limit the impact of the use of such wagons on quieter routes, which are compatible with the purpose of preserving the above-mentioned cross-border freight traffic.If the revision set out in the paragraph above takes place, the Commission shall report annually thereafter on the progress on technical and operational solutions for the operation of freight wagons in winter conditions. It shall provide an estimation of the number of wagons equipped with cast iron brake blocks necessary to ensure continued cross border traffic to and from such Nordic regions, with a view to ending the exemption in 2028 at the latest.
Article 6Compliance with the lower exposure action values set out in Article 3 of Directive 2003/10/EC of the European Parliament and of the CouncilDirective 2003/10/EC of the European Parliament and of the Council of 6 February 2003 on the minimum health and safety requirements regarding the exposure of workers to the risks arising from physical agents (noise) (Seventeenth individual Directive within the meaning of Article 16(1) of Directive 89/391/EEC) (OJ L 42, 15.2.2003, p. 38). shall be ensured by compliance with the driver's cabin interior noise level, as set out in point 4.2.4 of the Annex to this Regulation as well as by appropriate operational conditions to be defined by the railway undertaking.
Article 71.In order to adapt to technological progress, innovative solutions may be proposed by the manufacturer or its authorised representative which do not comply with the specifications set out in the Annex and/or for which the assessment methods set out in the Annex cannot be applied.2.Innovative solutions may be related to the rolling stock subsystem, its parts and its interoperability constituents.3.Where an innovative solution is proposed, the manufacturer or his authorised representative established within the Union shall state in what way it deviates from or how it complements the relevant provisions of this TSI and shall submit the deviations to the Commission for analysis. The Commission may request the opinion of the Agency on the proposed innovative solution.4.The Commission shall deliver an opinion on the proposed innovative solution. If this opinion is positive, the appropriate functional and interface specifications and the assessment method, which need to be included in the TSI in order to allow the use of this innovative solution, shall be developed by the Agency and subsequently integrated into the TSI during the revision process pursuant to Article 5 of Directive (EU) 2016/797. If the opinion is negative, the proposed innovative solution shall not be used.5.Pending the review of the TSI, a positive opinion delivered by the Commission shall be considered as an acceptable means of compliance with the essential requirements of Directive (EU) 2016/797 and may therefore be used for the assessment of the subsystem.
Article 8The declaration of verification and/or conformity to type of a new vehicle established in accordance with Decision 2011/229/EU shall be considered valid:for locomotives, EMUs, DMUs and coaches until the type or design certificate needs to be renewed as stated in Decision 2011/291/EU for cases where the latter decision was applied, or until 31 May 2017 for other cases,for wagons until 13 April 2016.The declaration of verification and/or conformity to type of a new vehicle established in accordance with Decision 2008/232/EC shall be considered valid until the type or design certificate needs to be renewed as stated in this Decision.
Article 91.Decision 2011/229/EU is repealed with effect from 1 January 2015.2.In the Annex to Decision 2008/232/EC, points 4.2.6.5, 4.2.7.6 and 7.3.2.15 are deleted with effect from 1 January 2015.3.The provisions referred to in paragraphs 1 and 2 shall however continue to apply in relation to projects authorised in accordance with the TSI annexed to those Decisions and, unless the applicant requests to apply this Regulation, to projects relating to new vehicles and to the renewal or upgrading of existing vehicles which are at an advanced stage of development, are the subject of a contract in force on the date of publication of this Regulation or cases referred to in Article 8 of this Regulation.
Article 10This Regulation shall enter into force on the twentieth day following that of its publication in the Official Journal of the European Union.It shall apply from 1 January 2015. However, an authorisation for placing into service may be granted in application of the TSI as set out in the Annex to this Regulation, before 1 January 2015.
This Regulation shall be binding in its entirety and directly applicable in the Member States in accordance with the Treaties.ANNEXTABLE OF CONTENTS1.INTRODUCTION1.1.Technical scope1.1.1.Scope related to rolling stock1.1.2.Scope related to operational aspects1.2.Geographical scope2.DEFINITION OF THE SUBSYSTEM3.ESSENTIAL REQUIREMENTS4.CHARACTERISATION OF THE SUBSYSTEM4.1.Introduction4.2.Functional and technical specifications of the subsystems4.2.1.Limits for stationary noise4.2.2.Limits for starting noise4.2.3.Limits for pass-by noise4.2.4.Limits for the driver's cab interior noise4.3.Functional and technical specifications of the interfaces4.4.Operating rules4.4.1.Specific rules for the operation of wagons on quieter routes in case of degraded operation4.4.2.Specific rules for the operation of wagons on quieter routes in case of infrastructure works and wagons maintenance4.5.Maintenance rules4.6.Professional qualifications4.7.Health and safety conditions4.8.European register of authorised types of vehicles5.INTEROPERABILITY CONSTITUENTS6.CONFORMITY ASSESSMENT AND EC VERIFICATION6.1.Interoperability constituents6.2.Subsystem rolling stock regarding noise emitted by rolling stock6.2.1.Modules6.2.2.EC verification procedures6.2.3.Simplified evaluation7.IMPLEMENTATION7.1.Application of this TSI to new subsystems7.2.Application of this TSI to existing subsystems7.2.1.Provisions in case of changes to existing rolling stock or rolling stock type7.2.2.Additional provisions for the application of this TSI to existing wagons7.3.Specific cases7.3.1.Introduction7.3.2.List of specific cases7.4.Particular implementation rules7.4.1.Particular implementation rules for the application of this TSI to existing wagons (point 7.2.2)7.4.2.Particular implementation rules for wagons operated on quieter routes (point 7.2.2.2)1.INTRODUCTIONIn general Technical Specifications for Interoperability (TSI) lay down for each subsystem (or part of it) the optimal level of harmonised specifications in order to ensure the interoperability of the rail system. Therefore TSIs harmonise only the specifications concerning parameters which are critical to interoperability (basic parameters). The specifications of the TSIs must meet the essential requirements as set out in Annex III of Directive (EU) 2016/797.In line with the proportionality principle this TSI sets out the optimal level of harmonisation related to specifications on the rolling stock subsystem as defined in Section 1.1 intended to limit the noise emission of the rail system within the Union.1.1.Technical scope1.1.1.Scope related to rolling stockThis TSI applies to all rolling stock within the scope of Regulation (EU) No 1302/2014 (LOC&PAS TSI) and Regulation (EU) No 321/2013 (WAG TSI);1.1.2.Scope related to operational aspectsAlongside with Commission Decision 2012/757/EUCommission Decision 2012/757/EU of 14 November 2012 concerning the technical specification for interoperability relating to the operation and traffic management subsystem of the rail system in the European Union and amending Decision 2007/756/EC (OJ L 345, 15.12.2012, p. 1). (OPE TSI), this TSI applies to the operation of freight wagons which are used on railway infrastructure designated as "quieter routes".1.2.Geographical scopeThe geographical scope of this TSI corresponds to the scopes defined in Section 1.2 of Regulation (EU) No 1302/2014 and in Section 1.2 of Regulation (EU) No 321/2013, each for their rolling stock (RST) concerned.2.DEFINITION OF THE SUBSYSTEMA "unit" means the rolling stock which is subject to the application of this TSI, and therefore subject to the "EC" verification procedure. Chapter 2 in the annex to Regulation (EU) No 1302/2014 and chapter 2 in the annex to Regulation (EU) No 321/2013 describe what a unit can consist of.The requirements of this TSI apply to the following categories of rolling stock set out in section 2 in Annex I of Directive (EU) 2016/797:(a)Locomotives and passenger rolling stock including thermal or electric traction units, self-propelling thermal or electric passenger trains, and passenger coaches. This category is further defined in chapter 2 in the annex to Regulation (EU) No 1302/2014 and shall be referred to in this TSI as locomotives, electric multiple units (EMU), diesel multiple units (DMU) and coaches;(b)Freight wagons, including low-deck vehicles designed for the entire network and vehicles designed to carry lorries. This category is further defined in chapter 2 in the annex to Regulation (EU) No 321/2013 and shall be referred to in this TSI as wagons;(c)Special vehicles, such as on-track machines. This category is further defined in chapter 2 in the annex to Regulation (EU) No 1302/2014 and consists of on-track machines (referred to in this TSI as OTMs) and infrastructure inspection vehicles, which belong to the categories in points (a) or (b) depending on their design.3.ESSENTIAL REQUIREMENTSAll basic parameters set out in this TSI shall be linked to at least one of the essential requirements as set out in Annex III of Directive (EU) 2016/797. Table 1 indicates the allocation.
Table 1Basic parameters and their link to the essential requirements
PointBasic parameterEssential requirements
SafetyReliability and availabilityHealthEnvironmental protectionTechnical compatibilityAccessibility
4.2.1Limits for stationary noise1.4.4
4.2.2Limits for starting noise1.4.4
4.2.3Limits for pass-by noise1.4.4
4.2.4Limits for driver's cab interior noise1.4.4
4.CHARACTERISATION OF THE SUBSYSTEM4.1.IntroductionThis Chapter sets out the optimal level of harmonisation related to specifications on the rolling stock subsystem intended to limit the noise emission of the Union rail system and to achieve interoperability.4.2.Functional and technical specifications of the subsystemsThe following parameters have been identified as critical for the interoperability (basic parameters):(a)"stationary noise";(b)"starting noise";(c)"pass-by noise";(d)"driver's cab interior noise".The corresponding functional and technical specifications allocated to the different categories of rolling stock are set out in this section. In case of units equipped with both thermal and electric power the relevant limit values under all normal operation modes shall be respected. If one of these operation modes foresees the use of both thermal and electric power at the same time the less restrictive limit value applies. In accordance with Articles 4(5) and 2(13) of Directive (EU) 2016/797, provision may be made for specific cases. Such provisions are indicated in Section 7.3.The assessment procedures for the requirements in this section are defined in the indicated points and sub points of Chapter 6.4.2.1.Limits for stationary noiseThe limit values for the following sound pressure levels under normal vehicle conditions concerning the stationary noise allocated to the categories of the rolling stock subsystem are set out in Table 2:(a)the A-weighted equivalent continuous sound pressure level of the unit (LpAeq,T[unit]);(b)the A-weighted equivalent continuous sound pressure level at the nearest measuring position i considering the main air compressor (LipAeq,T); and(c)the AF-weighted sound pressure level at the nearest measuring position i considering impulsive noise of the exhaust valve of the air dryer (LipAFmax).The limit values are defined at a distance of 7,5 m from the centre of the track and 1,2 m above top of rail.
Table 2Limit values for stationary noise
Category of the rolling stock subsystemLpAeq,T [unit] [dB]LipAeq,T [dB]LipAFmax [dB]
Electric locomotives and OTMs with electric traction707585
Diesel locomotives and OTMs with diesel traction7178
EMUs6568
DMUs7276
Coaches6468
Wagons65n.a.n.a.
The demonstration of conformity is described in point 6.2.2.1.4.2.2.Limits for starting noiseThe limit values for the AF-weighted maximum sound pressure level (LpAF,max) concerning the starting noise allocated to the categories of the rolling stock subsystem are set out in Table 3. The limit values are defined at a distance of 7,5 m from the centre of the track and 1,2 m above top of rail.
Table 3Limit values for starting noise
Category of the rolling stock subsystemLpAF,max [dB]
Electric locomotives with total tractive power P < 4500 kW81
Electric locomotives with total tractive power P ≥ 4500 kWOTMs with electric traction84
Diesel locomotives P < 2000 kW at the engine output shaft85
Diesel locomotives P ≥ 2000 kW at the engine output shaftOTMs with diesel traction87
EMUs with a maximum speed vmax < 250 km/h80
EMUs with a maximum speed vmax ≥ 250 km/h83
DMUs P < 560 kW/engine at the engine output shaft82
DMUs P ≥ 560 kW/engine at the engine output shaft83
The demonstration of conformity is described in point 6.2.2.2.4.2.3.Limits for pass-by noiseThe limit values for the A-weighted equivalent continuous sound pressure level at a speed of 80 km/h (LpAeq,Tp,(80 km/h)) and, if applicable, at 250 km/h (LpAeq,Tp,(250 km/h)) concerning the pass-by noise allocated to the categories of the rolling stock subsystem are set out in Table 4. The limit values are defined at a distance of 7,5 m from the centre of the track and 1,2 m above top of rail.Measurements at speeds higher than or equal to 250 km/h shall also be made at the "additional measurement position" with a height of 3,5 m above top of rail in accordance with Chapter 6 of EN ISO 3095:2013 and assessed against the applicable limit values of Table 4.
Table 4Limit values for pass-by noiseAPL: the number of axles divided by the length over the buffers (m-1)
Category of the rolling stock subsystemLpAeq,Tp (80 km/h) [dB]LpAeq,Tp (250 km/h) [dB]
Electric locomotives and OTMs with electric traction8499
Diesel locomotives and OTMs with diesel traction85n.a.
EMUs8095
DMUs8196
Coaches79n.a.
Wagons (normalised to APL = 0,225)83n.a.
The demonstration of conformity is described in point 6.2.2.3.4.2.4.Limits for the driver's cab interior noiseThe limit values for the A-weighted equivalent continuous sound pressure level (LpAeq,T) concerning the noise within the driver's cab of electric and diesel locomotives, OTMs, EMUs, DMUs and coaches fitted with a cab are set out in Table 5. The limit values are defined in the vicinity of the driver's ear.
Table 5Limit values for driver's cab interior noise
Noise within the driver's cabLpAeq,T [dB]
At standstill with horns sounding95
At maximum speed vmax if vmax < 250 km/h78
At maximum speed vmax if 250 km/h ≤ vmax < 350 km/h80
The demonstration of conformity is described in point 6.2.2.4.4.3.Functional and technical specifications of the interfacesThis TSI has the following interfaces with the rolling stock subsystem:Interface with subsystems of points (a), (b), (c) and (e) of chapter 2 (dealt with in Regulation (EU) No 1302/2014) with regard to:stationary noise,starting noise (not applicable to coaches),pass-by noise,interior noise within the driver's cab, where applicable.Interface with subsystems of point (d) of chapter 2 (dealt with in Regulation (EU) No 321/2013) with regard to:pass-by noise,stationary noise.This TSI has the following interface with the operation and traffic management subsystem (dealt with in Decision 2012/757/EU) with regard to:pass-by noise.4.4.Operating rulesRequirements concerning the operating rules for the subsystem rolling stock are set out in section 4.4 of the Annex of Regulation (EU) No 1302/2014 and in section 4.4 of the Annex of Regulation (EU) No 321/2013.4.4.1.Specific rules for the operation of wagons on quieter routes in case of degraded operationThe contingency arrangements as defined in point 4.2.3.6.3 of the Annex of Decision 2012/757/EU include the operation of wagons not compliant with point 7.2.2.2 on quieter routes.This measure can be applied to address capacity restrictions or operational constraints caused by rolling stock failures, extreme weather conditions, accidents or incidents and infrastructure failures.4.4.2.Specific rules for the operation of wagons on quieter routes in case of infrastructure works and wagons maintenanceThe operation of wagons not compliant with point 7.2.2.2 on quieter routes shall be possible in case of wagons maintenance activities where only a quieter route is available in order to access the maintenance workshop.Contingency arrangements set out in point 4.4.1 are applicable in case of infrastructure works where a quieter route is the only suitable alternative.4.5.Maintenance rulesRequirements concerning the maintenance rules for the subsystem rolling stock are set out in section 4.5 of the Annex of Regulation (EU) No 1302/2014 and in section 4.5 of the Annex of Regulation (EU) No 321/2013.4.6.Professional qualificationsNot applicable.4.7.Health and safety conditionsSee Article 6 of this Regulation.4.8.European register of authorised types of vehiclesThe data of the rolling stock that must be recorded in the "European register of authorised types of vehicles (ERATV)" are set out in Decision 2011/665/EU.5.INTEROPERABILITY CONSTITUENTSThere is no interoperability constituent specified in this TSI.6.CONFORMITY ASSESSMENT AND EC VERIFICATION6.1.Interoperability constituentsNot applicable.6.2.Subsystem rolling stock regarding noise emitted by rolling stock6.2.1.ModulesThe EC verification shall be performed in accordance with the module(s) described in Table 6.
Table 6Modules for EC verification of subsystems
SBEC-Type Examination
SDEC verification based on quality management system of the production process
SFEC verification based on product verification
SH1EC verification based on full quality management system plus design examination
These modules are specified in detail in Decision 2010/713/EU.6.2.2.EC verification proceduresThe applicant shall choose one of the following assessment procedures consisting of one or more modules for the EC verification of the subsystem:(SB+SD),(SB+SF),(SH1).Within the application of the chosen module or module combination the subsystem shall be assessed against the requirements defined in Section 4.2. If necessary, additional requirements concerning the assessment are given in the following points.6.2.2.1.Stationary noiseThe demonstration of conformity with the limit values on stationary noise as set out in point 4.2.1 shall be carried out in accordance with Sections 5.1, 5.2, 5.3, 5.4, 5.5 (without clause 5.5.2), 5.7 and clause 5.8.1 of EN ISO 3095:2013.For the assessment of the main air compressor noise at the nearest measuring position i, the LipAeq,T indicator shall be used with T representative of one operating cycle as defined in Section 5.7 of EN ISO 3095:2013. Only the train systems that are required for the air compressor to run under normal operating conditions shall be used for this. The train systems which are not needed for the operation of the compressor may be switched off to prevent contribution to the noise measurement. The demonstration of conformity with the limit values shall be carried out under the conditions solely necessary for operation of the main air compressor at the lowest rpm.For the assessment of the impulsive noise sources at the nearest measuring position i, the LipAFmax indicator shall be used. The relevant noise source is the exhaust from the valves of the air dryer.6.2.2.2.Starting noiseThe demonstration of conformity with the limit values on starting noise as set out in point 4.2.2 shall be carried out in accordance with Chapter 7 (without clause 7.5.1.2) of EN ISO 3095:2013. The maximum level method referring to Section 7.5 of EN ISO 3095:2013 shall apply. Deviating from clause 7.5.3 of EN ISO 3095:2013 the train shall accelerate from standstill up to 30 km/h and then maintain the speed.In addition the noise shall be measured at a distance of 7,5 m from the centre of the track and a height of 1,2 m above top of rail. The "averaged level method" and the "maximum level method" in accordance with Section 7.6 and 7.5 respectively of EN ISO 3095:2013 shall apply and the train shall accelerate from standstill up to 40 km/h and then maintain the speed. The measured values are not assessed against any limit value and shall be recorded in the technical file and communicated to the Agency.For OTMs the starting procedure shall be performed without additional trailer loads.6.2.2.3.Pass-by noiseThe demonstration of conformity with the limit values on pass-by noise as set out in point 4.2.3 shall be carried out in accordance with points 6.2.2.3.1 and 6.2.2.3.2.6.2.2.3.1.Test track conditionsThe tests shall be performed on a reference track as defined in Section 6.2 of EN ISO 3095:2013.However, it is permitted to carry out the test on a track that does not comply with the reference track conditions in terms of acoustic rail roughness level and track decay rates as long as the noise levels measured in accordance with point 6.2.2.3.2 do not exceed the limit values set out in point 4.2.3.The acoustic rail roughness and the decay rates of the test track shall be determined in any case. If the track on which the tests are performed does meet the reference track conditions, the measured noise levels shall be marked "comparable", otherwise they shall be marked "non-comparable". It shall be recorded in the technical file whether the measured noise levels are "comparable" or "non-comparable".The measured acoustic rail roughness values of the test track remain valid during a period starting 3 months before and ending 3 months after this measurement, provided that during this period no track maintenance has been performed which influences the rail acoustic roughness.The measured track decay rate values of the test track shall remain valid during a period starting 1 year before and ending 1 year after this measurement, provided that during this period no track maintenance has been performed which influences the track decay rates.Confirmation shall be provided in the technical file that the track data related to the type's pass-by noise measurement were valid during the day(s) of testing, e.g. by providing the date of last maintenance having an impact on noise.Furthermore, it is permitted to carry out tests at speeds equal to or higher than 250 km/h on slab tracks. In this case the limit values shall be 2 dB higher than those set out in point 4.2.3.6.2.2.3.2.ProcedureThe tests shall be carried out in accordance with the provision in Sections 6.1, 6.3, 6.4, 6.5, 6.6 and 6.7 (without 6.7.2) of EN ISO 3095:2013. Any comparison against limit values shall be carried out with results rounded to the nearest integer decibel. Any normalisation shall be performed before rounding. The detailed assessment procedure is set out in points 6.2.2.3.2.1, 6.2.2.3.2.2 and 6.2.2.3.2.3.6.2.2.3.2.1.EMU, DMUs, locomotives and coachesFor EMU, DMUs, locomotives and coaches three classes of maximum operational speed are distinguished:(1)If the maximum operational speed of the unit is lower than or equal to 80 km/h, the pass-by noise shall be measured at its maximum speed vmax. This value shall not exceed the limit value LpAeq,Tp(80 km/h) as set out in point 4.2.3.(2)If the maximum operational speed vmax of the unit is higher than 80 km/h and lower than 250 km/h, the pass-by noise shall be measured at 80 km/h and at its maximum speed. Both measured pass-by noise values LpAeq,Tp(vtest) shall be normalised to the reference speed of 80 km/h LpAeq,Tp(80 km/h) using formula (1). The normalised value shall not exceed the limit value LpAeq,Tp(80 km/h) as set out in point 4.2.3.Formula (1):LpAeq,Tp(80 km/h) = LpAeq,Tp(vtest) – 30 * log (vtest/80 km/h)vtestActual speed during the measurement(3)If the maximum operational speed vmax of the unit is equal to or higher than 250 km/h, the pass-by noise shall be measured at 80 km/h and at its maximum speed with an upper test speed limit of 320 km/h. The measured pass-by noise value LpAeq,Tp(vtest) at 80 km/h shall be normalised to the reference speed of 80 km/h LpAeq,Tp(80 km/h) using formula (1). The normalised value shall not exceed the limit value LpAeq,Tp(80 km/h) as set out in point 4.2.3. The measured pass-by noise value at maximum speed LpAeq,Tp(vtest) shall be normalised to the reference speed of 250 km/h LpAeq,Tp(250 km/h) using formula (2). The normalised value shall not exceed the limit value LpAeq,Tp(250 km/h) as set out in point 4.2.3.Formula (2):LpAeq,Tp(250 km/h) = LpAeq,Tp(vtest) – 50 * log(vtest/250 km/h)vtestActual speed during the measurement6.2.2.3.2.2.WagonsFor wagons two classes of maximum operational speed are distinguished:(1)If the maximum operational speed vmax of the unit is lower than or equal to 80 km/h, the pass-by noise shall be measured at its maximum speed. The measured pass-by noise value LpAeq,Tp(vtest) shall be normalised to a reference APL of 0,225 m-1 LpAeq,Tp (APLref) using formula (3). This value shall not exceed the limit value LpAeq,Tp(80 km/h) as set out in point 4.2.3.Formula (3):LpAeq,Tp (APLref) = LpAeq,Tp(vtest) – 10 * log(APLwag/0,225 m-1)APLwagNumber of axles divided by the length over the buffers [m-1]vtestActual speed during the measurement(2)If the maximum operational speed vmax of the unit is higher than 80 km/h, the pass-by noise shall be measured at 80 km/h and at its maximum speed. Both measured pass-by noise values LpAeq,Tp(vtest) shall be normalised to the reference speed of 80 km/h and to a reference APL of 0,225 m-1 LpAeq,Tp(APL ref, 80 km/h) using formula (4). The normalised value shall not exceed the limit value LpAeq,Tp(80 km/h) as set out in point 4.2.3.Formula (4):LpAeq,Tp (APLref, 80 km/h) = LpAeq,Tp(vtest) – 10 * log(APLwag/0,225 m-1) — 30 * log(vtest/80 km/h)APLwagNumber of axles divided by the length over the buffers [m-1]vtestActual speed during the measurement6.2.2.3.2.3.OTMsFor OTMs the same assessment procedure as set out in 6.2.2.3.2.1 applies. The measuring procedure shall be performed without additional trailer loads.OTMs are deemed to comply with the pass-by noise level requirements in point 4.2.3 without measuring when they are:solely braked by either composite brake blocks or disc brakes, andequipped with composite scrubbers, if scrubber blocks are fitted.6.2.2.4.Driver's cab interior noiseThe demonstration of conformity with the limit values on the driver's cab interior noise as set out in point 4.2.4 shall be carried out in accordance with EN 15892:2011. For OTMs the measuring procedure shall be performed without additional trailer loads.6.2.3.Simplified evaluationInstead of the test procedures as set out in point 6.2.2, it is permitted to substitute some or all of the tests by a simplified evaluation. The simplified evaluation consists of acoustically comparing the unit under assessment to an existing type (further referred to as the reference type) with documented noise characteristics.The simplified evaluation may be used for each of the applicable basic parameters "stationary noise", "starting noise", "pass-by noise" and "driver's cab interior noise" autonomously and shall consist of providing evidence that the effects of the differences of the unit under assessment do not result in exceeding the limit values set out in Section 4.2.For the units under simplified evaluation, the proof of conformity shall include a detailed description of the noise relevant changes compared to the reference type. From this description, a simplified evaluation shall be performed. The estimated noise values shall include the uncertainties of the applied evaluation method. The simplified evaluation can either be a calculation and/or simplified measurement.A unit certified on the basis of the simplified evaluation method shall not be used as a reference unit for a further evaluation.If the simplified evaluation is applied for pass-by noise, the reference-type shall comply with at least one of the following:Chapter 4 and for which the pass-by noise results are marked "comparable"Chapter 4 of Decision 2011/229/EU and for which the pass-by noise results are marked "comparable"Chapter 4 of Decision 2006/66/ECChapter 4 of Decision 2008/232/EC.In case of a wagon whose parameters remain, compared to the reference type, within the permitted range of Table 7 it is deemed without further verification that the unit complies with the limit values on pass-by noise as set out in point 4.2.3.
Table 7Permitted variation of wagons for the exemption from verification
ParameterPermitted variation (compared to the reference unit)
Max. unit speedAny speed up to 160 km/h
Type of wheelOnly if equally or less noisy (acoustic characterisation i. a. w. Annex E of EN 13979-1:2011)
Tare weightOnly within the range of +20 %/- 5 %
Brake blockOnly if variation does not result in higher noise emission.
7.IMPLEMENTATION7.1.Application of this TSI to new subsystemsSee Article 8 of this Regulation.7.2.Application of this TSI to existing subsystemsThe principles to be applied by the applicants and authorising entities in case of change(s) to an existing rolling stock or rolling stock type are defined in point 7.1.2 of the Annex to Regulation (EU) No 1302/2014 and section 7.2 of the Annex to Regulation (EU) No 321/2013.7.2.1.Provisions in case of changes to existing rolling stock or rolling stock typeThe applicant shall ensure that the noise levels of rolling stock subject to change(s) remain below the limits set out in the TSI, which was applicable when the rolling stock in question was first authorised. If no TSI existed at the time of the first authorisation, the applicant shall ensure that the noise levels of the rolling stock subject to change(s) are either not increased or remain below the limits set out in Decision 2006/66/EC or Decision 2002/735/EC.If an assessment is required, it shall be limited to the basic parameters affected by the change(s).If the simplified evaluation is applied, the original unit may represent the reference unit in accordance with the provisions of point 6.2.3.The replacement of a whole unit or (a) vehicle(s) within a unit (e.g. a replacement after a severe damage) does not require a conformity assessment against this TSI, as long as the unit or the vehicle(s) are identical to the ones they replace.7.2.2.Additional provisions for the application of this TSI to existing wagonsThe restriction of the operation set out in Article 5a of this Regulation shall not apply to wagons mostly operated on lines with a gradient of more than 40 ‰, wagons with a maximum operating speed higher than 120 km/h, wagons with a maximum axle load higher than 22,5 t, wagons exclusively operated for infrastructure works and wagons used in rescue trains.If a wagon is being equipped with quieter brake blocks as defined in point 7.2.2.1 and no noise sources are added to the wagon, then it shall be assumed that the requirements of point 4.2.3 are met without further testing.7.2.2.1.Quieter brake blocksA quieter brake block is a brake block belonging to one of the following categories:Brake block listed in Appendix G of Regulation (EU) No 321/2013;Brake block assessed in accordance with the procedure set out in Appendix F of this TSI.7.2.2.2.Wagons operated on quieter routesWagons belonging to one of the categories below can be operated on the quieter routes within their area of use:Wagons holding an EC declaration of verification against Commission Decision 2006/66/EC concerning the technical specification for interoperability relating to the subsystem "rolling stock — noise" of the trans-European conventional rail system;Wagons holding an EC declaration of verification against Commission Decision 2011/229/EU concerning the technical specifications of interoperability relating to the subsystem "rolling stock – noise" of the trans-European conventional rail system;Wagons holding an EC declaration of verification against this TSI;Wagons fitted with quieter brake blocks as defined in point 7.2.2.1 or brake discs for the service brake function;Wagons fitted with composite brake blocks listed in Appendix E for the service brake function. The operation of these wagons on the quieter routes shall be limited in accordance with the conditions described in this appendix.7.3.Specific cases7.3.1.IntroductionThe specific cases, as listed in point 7.3.2, are classified as(a)"P" cases"permanent" cases;(b)"T" cases"temporary" cases.7.3.2.List of specific cases7.3.2.1.Specific cases(a)Specific case Estonia, Finland, Latvia, Lithuania, Poland and Slovakia("P") For units, which are in shared use with third countries, the track gauge of which is different from that of the main rail network within the Union, the application of national technical rules instead of the requirements in this TSI shall be permitted.(b)Specific case Finland("T") Decision 2011/229/EU may continue to apply for freight wagons to be used only on the territory of Finland and until the relevant technical solution in relation to severe winter conditions is found, but in any case not later than until 31 December 2032. This shall not prevent freight wagons from other Member States to operate on the Finnish network.7.3.2.2.Limits for stationary noise (point 4.2.1)(a)Specific case Finland("T") For coaches and wagons equipped with a diesel generator for electrical power supply higher than 100 kW and intended to operate solely on the railway network of Finland the limit value for stationary noise LpAeq,T [unit] in Table 2 may be raised up to 72 dB.Decision 2011/229/EU may continue to be applied for freight wagons to be used only on the territory of Finland and until the relevant technical solution in relation to Nordic winter conditions is found, but in any case not later than until 31 December 2017. This shall not prevent freight wagons from other Member States to operate on the Finnish network.(b)Specific case UK for Great Britain("P") For DMUs intended to operate solely on the railway network of Great Britain the limit value for stationary noise LpAeq,T [unit] in Table 2 may be raised up to 77 dB.This specific case does not apply to DMUs intended to operate solely on the High Speed 1 railway network.(c)Specific case UK for Great Britain("T") For units intended to operate solely on the railway network of Great Britain the limit values LipAeq,T in Table 2 considering the main air compressor do not apply. The measured values shall be submitted to the NSA UK.This specific case does not apply to units intended to operate solely on the High Speed 1 railway network.7.3.2.3.Limits for starting noise (point 4.2.2)(a)Specific case Sweden("T") For locomotives with total tractive power of more than 6000 kW and a maximum axle load of more than 25 t the limit values for starting noise LpAF,max in Table 3 may be raised up to 89 dB.(b)Specific case UK for Great Britain("P") For units specified in Table 8 intended to operate solely on the railway network of Great Britain the limit value for starting noise LpAF,max in Table 3 may be raised up to the values set out in Table 8.
Table 8Limit values for starting noise regarding a specific case UK for Great Britain
Category of the rolling stock subsystemLpAF,max [dB]
Electric locomotives with total tractive power P < 4500 kW83
Diesel locomotives P < 2000 kW at the engine output shaft89
DMUs85
This specific case does not apply to units intended to operate solely on the High Speed 1 railway network.7.3.2.4.Limits for pass-by noise (point 4.2.3)(a)Specific case Channel Tunnel("P") For the Channel Tunnel, the limits for pass-by noise shall not apply to wagons dedicated to the transport of heavy goods vehicles between Coquelles (France) and Folkestone (United Kingdom).(b)Specific case Sweden("T") For locomotives with total tractive power of more than 6000 kW and a maximum axle load of more than 25 t the limit values for pass-by noise LpAeq,Tp (80 km/h) in Table 4 may be raised up to 85 dB.7.4.Particular implementation rules7.4.1.Particular implementation rules for the application of this TSI to existing wagons (point 7.2.2)(a)Particular implementation rules for the application of this TSI to existing wagons in the Channel Tunnel("P") For the calculation of the annual average daily operated freight trains during night-time the freight trains composed of wagons dedicated to the transport of heavy goods vehicles confined in the Coquelles (France) - Folkestone (United Kingdom) line shall not be taken into account.(b)Particular implementation rules for the application of this TSI to existing wagons in Finland and Sweden("T") The concept of quieter routes shall not apply on the Finnish and Swedish networks due to uncertainties related to the operation in severe winter conditions with composite brake blocks until 31 December 2032. This shall not prevent freight wagons from other Member States to operate on the Finnish and Swedish network.7.4.2.Particular implementation rules for wagons operated on quieter routes (point 7.2.2.2)(a)Particular implementation rules for wagons operated on quieter routes of Belgium("T") On top of the wagons listed in point 7.2.2.2, the following existing wagons can be operated on quieter routes in the territory of Belgium:Wagons with tyred wheels until 31 December 2026Wagons which require the fitting of a kink valve in order to replace the cast iron block with composite brake blocks until 31 December 2026Wagons fitted with cast iron blocks which require the replacement of wheels with wheels compliant with the requirements set out in EN 13979-1:2003+A2:2011 in order to be retrofitted with composite brake blocks until 31 December 2026(b)Particular implementation rules for wagons operated on quieter routes of Channel Tunnel("P") On top of the wagons listed in point 7.2.2.2, the following existing wagons can be operated on quieter routes in the Channel Tunnel concession:Wagons dedicated to the transport of heavy goods vehicles between Coquelles (France) and Folkestone (United Kingdom)(c)Particular implementation rules for wagons operated on quieter routes of Czechia("T") On top of the wagons listed in point 7.2.2.2, the following existing wagons can be operated on quieter routes in the territory of Czechia:Wagons with tyred wheels, until 31 December 2026Wagons with 59V type bearings until 31 December 2034Wagons which require the fitting of a kink valve in order to replace the cast iron block with composite brake blocks, until 31 December 2034Wagons with 1Bg or 1Bgu brake configuration fitted with cast iron brake blocks until 31 December 2036Wagons fitted with cast iron blocks which require the replacement of wheels with wheels compliant with the requirements set out in EN 13979-1:2003+A2:2011 in order to be retrofitted with composite brake blocks until 31 December 2029Furthermore, it shall not be mandatory to use composite brake blocks on quieter routes for existing wagons not covered by the five dashes above and for which there exists no one-to-one-solution for replacement of cast iron brake blocks until 31 December 2030.(d)Particular implementation rules for wagons operated on quieter routes of France("T") On top of the wagons listed in point 7.2.2.2, the following existing wagons can be operated on quieter routes in the territory of France:Wagons with 1Bg or 1Bgu brake configuration fitted with cast iron brake blocks until 31 December 2030Wagons fitted with small wheels (diameter under 920 mm) until 31 December 2030(e)Particular implementation rules for wagons operated on quieter routes of Italy("T") On top of the wagons listed in point 7.2.2.2, the following existing wagons can be operated on quieter routes in the territory of Italy:Wagons with tyred wheels until 31 December 2026Wagons which require the fitting of a kink valve in order to replace the cast iron block with composite brake blocks until 31 December 2026Wagons fitted with cast iron blocks which require the replacement of wheels with wheels compliant with the requirements set out in EN 13979-1:2003+A2:2011 in order to be retrofitted with composite brake blocks until 31 December 2026Furthermore, it shall not be mandatory to use composite brake blocks on quieter routes for existing wagons not covered by the three dashes above and for which there exists no one-to-one-solution for replacement of cast iron brake blocks until 31 December 2030.(f)Particular implementation rules for wagons operated on quieter routes of Poland("T") On top of the wagons listed in point 7.2.2.2, the following existing wagons can be operated on quieter routes in the territory of Poland until 31 December 2036:Wagons with tyred wheelsWagons with 1Bg or 1Bgu brake configuration fitted with cast iron blocksWagons designed for "S" traffic equipped with "SS" brake fitted with cast iron blocksWagons fitted with cast iron blocks and designed for "SS" traffic for which retrofitting with LL brake blocks would require fitting with wheels complying with EN 13979-1:2003+A2:2011 and a kink valve(g)Particular implementation rules for wagons operated on quieter routes of Slovakia("T") On top of the wagons listed in point 7.2.2.2, the following existing wagons can be operated on quieter routes in the territory of Slovakia:Wagons with tyred wheels until 31 December 2026Wagons with bogies of type 26-2.8 fitted with cast iron blocks P10 until 31 December 2036Wagons, which require the fitting of a kink valve in order to replace the cast iron block with composite brake blocks until 31 December 2036.("P") Wagons with bogies 2TS intended for circulation between Slovakia and third countries by means of exchange of bogies in the border station(h)Particular implementation rules for wagons operated on quieter routes of UK for Great Britain("P") For units intended to operate solely on the GB Network, where existing wagons are equipped with composite brake blocks published in GMGN 2688 it shall be permitted to operate on quieter routes("T") The following types of existing wagons equipped with cast iron brake blocks intended to operate on the GB Network shall be permitted to operate on quieter routes:Wagons equipped with a non-UIC braking system for which there are no compatible silent brake blocks available for retrofitting until 31 December 2030.Wagons with a designed braking distance of 810m or less from 60 mph in brake mode G (goods timing)/75 mph in brake mode P (passenger timing), where those wagons are operated in trains with other wagons which have stopping distances in accordance with the relevant UK(GB) national technical rules, until 31 December 2030Wagons used exclusively for the transport of nuclear products until 31 December 2050.
Loading ...