Article 1ScopeThis Regulation shall apply to the recycling processes carried out to waste batteries and accumulators from 1 January 2014.

Article 2DefinitionsFor the purposes of this Regulation, the following definitions shall apply:(1)"recycling process" means any reprocessing operation as referred to in Article 3(8) of Directive 2006/66/EC which is carried out on waste lead-acid, nickel-cadmium and other batteries and accumulators and results in the production of output fractions as defined in point 5 of this Article. The recycling process does not include sorting and/or preparation for recycling/disposal and may be carried out in a single facility or in several facilities;(2)"preparation for recycling" means treatment of waste batteries and/or accumulators prior to any recycling process, which shall, inter alia, include storage, handling, dismantling of battery packs or separation of fractions that are not part of the battery or accumulator itself;(3)"recycling efficiency" of a recycling process means the ratio obtained by dividing the mass of output fractions accounting for recycling by the mass of the waste batteries and accumulators input fraction expressed as a percentage;(4)"input fraction" means the mass of collected waste batteries and accumulators entering the recycling process as defined in Annex I;(5)"output fraction" means the mass of materials that are produced from the input fraction as a result of the recycling process, as defined in Annex I without undergoing further treatment, that have ceased to be waste or that will be used for their original purpose or for other purposes, but excluding energy recovery.

Article 3Calculation of recycling efficiency1.The method set out in Annex I shall be used to calculate the recycling efficiency of a process for recycling waste lead-acid, nickel-cadmium and other batteries and accumulators.2.The method set out in Annex II shall be used to calculate the rate of recycled lead content for any recycling process.3.The method set out in Annex III shall be used to calculate the rate of recycled cadmium content for any recycling process.4.Recyclers shall report the information shown in Annex IV, Annex V and Annex VI, as applicable, on an annual basis and shall send it to the Member State’s competent authorities by no later than four months from the end of a calendar year concerned. Recyclers shall send their first annual reports no later than the 30 April 2015.5.Reporting on the recycling efficiency shall cover all individual steps of recycling and all corresponding output fractions.6.Where a recycling process is carried out at more than one facility, the first recycler is responsible for submitting the information required under point 4 to the Member State’s competent authorities.

Article 4Entry into forceThis Regulation shall enter into force on the day of its publication in the Official Journal of the European Union.

This Regulation shall be binding in its entirety and directly applicable in all Member States.Done at Brussels, 11 June 2012.For the CommissionThe PresidentJosé Manuel BarrosoANNEX IMethod for the calculation of the recycling efficiency of the recycling process of waste batteries and accumulators1.The recycling efficiency of a recycling process is calculated as follows: 32012R0493_en_img_1

, [mass %]where:REcalculated recycling efficiency of a recycling process for the purpose of Article 12(4) of Directive 2006/66/EC [in mass %];moutputthe mass of output fractions accounting for recycling per calendar year;minputthe mass of input fractions entering the battery recycling process per calendar year.2.The recycling efficiency of a recycling process is calculated separately for the following waste battery types:lead-acid batteries and accumulators,nickel-cadmium batteries and accumulators, andother batteries and accumulators.3.The recycling efficiency is calculated on the basis of the overall chemical composition (at elemental/compound level) of the input and output fractions. The following applies in respect of the input fraction:recyclers shall determine the share of different types of waste battery or accumulator present in an input fraction by conducting a sorting analysis of the fraction (by continuous or representative sampling),the chemical composition of each type of waste battery or accumulator present in the input fraction is determined on the basis of the chemical composition of new batteries and accumulators when placed on the market or on the basis of available data of recyclers or on information provided by the battery producers,recyclers shall determine the overall chemical composition of the input fraction by applying the chemical composition analysis to the types of batteries or accumulators present in the input fraction.4.Emissions to the atmosphere are not accounted for the recycling efficiency.5.The mass of output fractions accounting for recycling is the mass, on a dry weight basis, of the elements or compounds contained in fractions resulting from the recycling of waste batteries and accumulators per calendar year [in tonnes]. The following may be, inter alia, accounted for output fractions:the carbon which is actually used as a reducing agent or which is a component of an output fraction of the recycling process, if it results from the input waste batteries and accumulators, on the condition that it is certified by an independent scientific authority and made publicly available. The carbon which is used for energy recovery is not accounted for the recycling efficiency,the oxygen, used as an oxidising agent, if it results from the input waste batteries and accumulators and if it is a component of an output fraction of the recycling process. The oxygen coming from the atmosphere is not accounted for the recycling efficiency,battery and accumulator materials contained in slag suitable and used for recycling purposes as defined in Article 3(8) of Directive 2006/66/EC other than landfill construction or backfilling operations, provided that this is in line with national requirements.6.The mass of input fractions entering the battery recycling process is the mass of collected waste batteries and accumulators on a dry weight basis entering the recycling process per calendar year [in tonnes], including:fluids and acids,the mass of external jacket of waste batteries and accumulators,and excluding:the mass of outer casings belonging to battery packs.ANNEX IIMethod for the calculation of the rate of recycled lead content1.The rate of recycled lead content is calculated as follows: 32012R0493_en_img_2

, [mass %]where:RPbcalculated rate of recycled lead (Pb) from a recycling process for the purpose of Article 12(4) of Directive 2006/66/EC [in mass %];mPb outputthe mass of Pb in output fractions accounting for recycling is the share of Pb contained in these fractions which results from the recycling of lead-acid batteries and accumulators per calendar year [in tonnes];mPb inputthe mass of Pb in the input fraction entering the battery recycling process is defined as the yearly average Pb content of waste lead-acid batteries and accumulators multiplied by the input mass of lead-acid batteries and accumulators per calendar year [in tonnes].2.In the output fraction the lead (Pb) contained in slag at the end of the recycling process is not accounted for the rate of recycled lead content.ANNEX IIIMethod for the calculation of the rate of recycled cadmium content1.The rate of recycled cadmium content is calculated as follows: 32012R0493_en_img_3

, [mass %]where:RCdcalculated rate of recycled cadmium (Cd) from a recycling process for the purpose of Article 12(4) of Directive 2006/66/EC [in mass %];mCd outputthe mass of Cd in output fractions accounting for recycling is the share of Cd contained in these fractions which results from the recycling of nickel-cadmium batteries and accumulators per calendar year [in tonnes].mCd inputthe mass of Cd in the input fraction entering the battery recycling process is defined as the yearly average Cd content of waste nickel-cadmium batteries and accumulators multiplied by the input mass of nickel-cadmium batteries and accumulators per calendar year [in tonnes].2.In the output fraction the cadmium (Cd) contained in slag at the end of the recycling process is not accounted for the rate of recycled cadmium content.ANNEX IVReporting on recycling efficiencies for lead-acid batteries and accumulators1.For lead-acid batteries and accumulators input into the recycling process the following information shall be reported:Notes:Facility treating the waste batteries and accumulators after collection, eventual sorting and preparation for recycling.Description of the complete battery recycling process, no matter if carried out by one or several facilities (including a description of the individual recycling steps and their output fractions).Description of waste batteries and accumulators as received after collection, eventual sorting and preparation for recycling.Wet mass of waste batteries and accumulators as received after collection, eventual sorting and preparation for recycling (the mass of separated impurities and outer casing of battery packs as well as the water content as specified in the field "overall composition" shall be subtracted for the calculation of the recycling efficiency).Data transferred from Annex IV(2).Calculated according to the formula for RE based on data reported according to Annex IV(2).Calculated according to the formula for RPb based on data reported according to Annex IV(2).Examples of impurities include plastic, ebonite chips, items/pieces of iron, fibres from electronic scrap, molten aluminium.

Recycling efficiency of a battery recycling process (lead-acid batteries)

Calendar year
Facility
Name
Street
City
Country
Contact person
E-mail
Tel.
Description of the complete battery recycling process:

Input to the complete battery recycling process

Description of waste batteries and accumulators	EWC code(optional)	Mass	Overall composition of input		minput
Description of waste batteries and accumulators	EWC code(optional)	t/a	Element or compound	mass %	[t/a]
			Element or compound	mass %	[t/a]
			Elements or components, which are not part of the input fractions

			Impurities
			Outer casing of battery pack
			Water (H2O)
			Other
			Elements or components, which are part of the input fractions
			Lead (Pb)
			Sulphuric acid (H2SO4)
			Plastics
			Other


			minput, total

			moutput, Pb
			moutput, total

Recycling efficiency (RE):	moutput/minput		mass %
Degree of recycled Pb (RPb):	mPb output/mPb input		mass %

2.For the individual steps of the recycling process of lead-acid batteries and accumulators the following information shall be reported:Notes:Facility carrying out an individual process step.For step 1 = the same as input into the complete battery recycling process.For subsequent steps = intermediate fractions from the previous process step.Intermediate fractions = fractions destined for subsequent step(s) in the recycling process.Resulting from the batteries input (dry mass).Facility to which the intermediate fraction is handed over or — if the further process step is carried out internally — the same as 1.Final output fractions accounting for recycling = that have ceased to be waste and that will be used for their original purpose or for other purposes without undergoing further treatment, but excluding energy recovery. See also examples in Annex I(5).Elements and compounds if they were component of the batteries input (waste battery). See special provisions and examples in Annex I(5). For lead (Pb) in slag see the provision in Annex II(2). Lead must be entered as "Pb".

Process step	1
Calendar year
Facility
Name
Street
City
Country
Contact person
E-mail
Tel.
Description of the individual process step:

Input (waste batteries or waste batteries fractions)Output(1)Intermediate fractions(2)Final output fractions accounting for recycling

Description of input	EWC code(optional)	Mass
Description of input	EWC code(optional)	t/a



Description of fraction	EWC code(optional)	Mass	Further treatment	Recipient	Further process step
Description of fraction	EWC code(optional)	t/a	Further treatment	Name
					1_1
					1_2
					1_3
					1_4
					1_5
					1_6
					1_7
					1_8
					1_9
					1_10
Element or compound	Fraction (non-waste) containing the element or compound	Concentration of the element or compound in the fraction	Mass of the element or compound, which results from batteries input	Fate of the fraction
Element or compound	Fraction (non-waste) containing the element or compound	mass %	t/a	Fate of the fraction


		moutput, Pb
		moutput, total

ANNEX VReporting on recycling efficiencies for nickel-cadmium batteries and accumulators1.For nickel-cadmium batteries and accumulators input into the recycling process the following information shall be reported:Notes:Facility reprocessing the waste batteries and accumulators after collection and eventual sorting.Description of the complete battery recycling process, no matter if carried out by one or several facilities (including a description of the individual recycling steps and their output fractions).Description of waste batteries and accumulators as received after collection and eventual sorting and preparation for recycling.Wet mass of waste batteries and accumulators as received after collection and eventual sorting (the mass of separated impurities and outer casing of battery packs as well as the water content as specified in the field "overall composition" shall be subtracted for the calculation of the recycling efficiency).Data transferred from Annex V(2).Calculated according to the formula for RE based on data reported according to Annex V(2).Calculated according to the formula for RCd based on data reported according to Annex V(2).Examples of impurities include plastic, ebonite chips, items/pieces of iron, fibres from electronic scrap, molten aluminium.

Recycling efficiency of a battery recycling process (nickel-cadmium batteries)

Calendar year
Facility
Name
Street
City
Country
Contact person
E-mail
Tel.
Description of the complete battery recycling process:

Input into the complete battery recycling process

Description of waste batteries and accumulators	EWC code(optional)	Mass	Overall composition of input		minput
Description of waste batteries and accumulators	EWC code(optional)	t/a	Element or compound	mass %	[t/a]
			Element or compound	mass %	[t/a]
			Elements or components, which are not part of the input fractions

			Impurities
			Outer casing of battery pack
			Water (H2O)
			Other
			Elements or components, which are part of the input fractions
			Cadmium (Cd)
			Nickel (Ni)
			Iron (Fe)
			Plastics
			Electrolyte

			minput, total

			moutput, Cd
			moutput, total

Recycling efficiency (RE):	moutput/minput		mass %
Degree of recycled Cd (RCd):	mCd output/mCd input		mass %

2.For the individual steps of the recycling process of nickel-cadmium batteries and accumulators the following information shall be reported:Notes:Facility carrying out an individual process step.For step 1 = the same as input into the complete battery recycling process.For subsequent steps = intermediate fractions from the previous process step.Intermediate fractions = fractions destined for subsequent step(s) in the recycling process.Resulting from the batteries input (dry mass).Facility to which the intermediate fraction is handed over or — if the further process step is carried out internally — the same as 1.Final output fractions accounting for recycling = that will be used for their original purpose or for other purposes without undergoing further treatment, see also examples in Annex I(5).Elements and compounds if they were component of the batteries input (waste battery). See special provisions and examples in Annex I(5). For cadmium (Cd) in slag see provisions in Annex III(2). Cadmium must be entered as "Cd".

Process step	1
Calendar year
Facility
Name
Street
City
Country
Contact person
E-mail
Tel.
Description of the individual process step:

Input (waste batteries or waste batteries fractions)Output(1)Intermediate fractions(2)Final output fractions accounting for recycling

Description of input	EWC code(optional)	Mass
Description of input	EWC code(optional)	T/a

Description of fraction	EWC code(optional)	Mass	Further treatment	Recipient	Further process step
Description of fraction	EWC code(optional)	t/a	Further treatment	Name
					1_1
					1_2
					1_3
					1_4
					1_5
					1_6
					1_7
					1_8
					1_9
					1_10
Element or compound	Fraction (non-waste) containing the element or compound	Concentration of the element or compound in the fraction	Mass of the element or compound, which results from batteries input	Fate of the fraction
Element or compound	Fraction (non-waste) containing the element or compound	mass %	t/a	Fate of the fraction


		moutput, Cd
		moutput, total

ANNEX VIReporting on recycling efficiencies for other batteries and accumulators1.For other batteries and accumulators input into the recycling process the following information shall be reported:Notes:Facility treating the waste batteries and accumulators after collection, eventual sorting and preparation for recycling.Description of the complete battery recycling process, no matter if carried out by one or several facilities (including a description of the individual recycling steps and their output fractions).Description of waste batteries and accumulators as received after collection, eventual sorting and preparation for recycling.Wet mass of waste batteries and accumulators as received after collection, eventual sorting and preparation for recycling (the mass of separated impurities and outer casing of battery packs as well as the water content as specified in the field "overall composition" shall be subtracted for the calculation of the recycling efficiency).Data transferred from Annex VI(2).Calculated according to the formula for RE based on data reported according to Annex VI(2).Examples of impurities include plastic, ebonite chips, items/pieces of iron, fibres from electronic scrap, molten aluminium.

Recycling efficiency of a battery recycling process (other batteries)

Calendar year
Facility
Name
Street
City
Country
Contact person
E-mail
Tel.
Description of the complete battery recycling process:

Input into the complete battery recycling process

Description of waste batteries and accumulators	EWC code(optional)	Mass	Overall composition of input		minput
Description of waste batteries and accumulators	EWC code(optional)	t/a	Element or compound	mass %	[t/a]
			Element or compound	mass %	[t/a]
			Elements or components, which are not part of the input fractions

			Impurities
			Outer casing of battery pack
			Water (H2O)
			Other
			Elements or components, which are part of the input fractions
			Metals (e.g. Fe, Mn, Zn, Ni, Co, Li, Ag, Cu, Al)
			Mercury (Hg)
			Carbon
			Plastics
			Electrolyte

			minput, total

			moutput, total

Recycling efficiency (RE):	moutput/minput		mass %

2.For the individual steps of the recycling process of other batteries and accumulators the following information shall be reported:Notes:Facility carrying out an individual process stepFor step 1 = the same as input into the complete battery recycling process.For subsequent steps = intermediate fractions from the previous process step.Intermediate fractions = fractions destined for subsequent step(s) in the recycling process.Resulting from the batteries input (dry mass).Facility to which the intermediate fraction is handed over or — if the further process step is carried out internally — the same as 1.Final output fractions accounting for recycling = that will be used for their original purpose or for other purposes without undergoing further treatment, see also examples in Annex I(5).Elements and compounds if they were component of the batteries input (spent battery). See special provisions and examples in Annex I(5).

Process step	1
Calendar year
Facility
Name
Street
City
Country
Contact person
E-mail
Tel.
Description of the individual process step:

Input (waste batteries or waste batteries fractions)Output(1)Intermediate fractions(2)Final output fractions accounting for recycling

Description of input	EWC code(optional)	Mass
Description of input	EWC code(optional)	t/a

Description of fraction	EWC code(optional)	Mass	Further treatment	Recipient	Further process step
Description of fraction	EWC code(optional)	t/a	Further treatment	Name
					1_1
					1_2
					1_3
					1_4
					1_5
					1_6
					1_7
					1_8
					1_9
					1_10
Element or compound	Fraction (non-waste) containing the element or compound	Concentration of the element or compound in the fraction	Mass of the element or compound, which results from batteries input	Fate of the fraction
Element or compound	Fraction (non-waste) containing the element or compound	mass %	t/a	Fate of the fraction


		moutput, total

Amendments and corrections
January 1, 2014	Application - See Art 1
June 12, 2012	Entry into force - Date pub. See Art 4