Article 1Subject-matterThis Regulation establishes a common safety method (CSM) for assessing conformity with requirements for obtaining safety certificates as referred to in Article 6(3)(b) of Directive 2004/49/EC.The CSM includes:(a)a procedure and criteria for assessing applications by railway undertakings for safety certificates as referred to in Article 10(2) of Directive 2004/49/EC, as set out in Annexes I, II and III to this Regulation;(b)principles for supervising compliance with the requirements of Directive 2004/49/EC after the national safety authority has granted the certificate, as set out in Annex IV to this Regulation.

Article 2DefinitionsFor the purposes of this Regulation, the following definition shall apply: "supervision" means the arrangements put in place by the national safety authority to oversee safety performance after it has granted a safety certificate.

Article 3Procedures for assessing applications1.When examining applications for both Part A and Part B safety certificates submitted after the entry into force of this Regulation, national safety authorities shall apply the procedure set out in Annex I to this Regulation for assessing their conformity with requirements in Directive 2004/49/EC. National safety authorities shall use the assessment criteria set out in Annex II to this Regulation for safety certificates issued in accordance with Article 10(3) of Directive 2004/49/EC and those contained in Annex III to this Regulation for safety certificates issued in accordance with Article 10(4) of Directive 2004/49/EC. These criteria shall also be used in case of renewal of safety certificates in accordance with Article 10(5) of Directive 2004/49/EC.2.During assessment, national safety authorities may accept commitments by applicants that they will manage risks through the use of contracts with third parties. The contracts shall also specify the exchange of information needed to ensure the safe operation of vehicles, especially in the areas relating to managing maintenance.3.Products or services provided by contractors or suppliers to railway undertakings shall be presumed to conform to safety requirements if the contractors, suppliers or products are certified in accordance with relevant certification schemes established under Union legislation, for the provision of such products and services.

Article 4SupervisionAfter granting a safety certificate, national safety authorities shall, for both Part A and Part B safety certificates, supervise railway undertakings’ continued application of their safety management system and shall apply the principles for supervision set out in Annex IV.

Article 5Entry into forceThis Regulation shall enter into force on the twentieth day following that of its publication in the Official Journal of the European Union.

This Regulation shall be binding in its entirety and directly applicable in all Member States.Done at Brussels, 9 December 2010.For the CommissionThe PresidentJosé Manuel BarrosoANNEX IProcedure for assessing conformity with requirements for obtaining safety certificates to be issued in accordance with Article 10(2)(a) and (b) of Directive 2004/49/EC1.The procedures that a national safety authority puts in place to receive and assess applications and to award safety certificates shall be built upon the following framework principles.(a)Setting up and reviewing the assessment processNational safety authorities shall develop structured and auditable processes to be undertaken by suitably competent persons. They shall scrutinise applications against the assessment criteria for safety management systems set out in Annex II and III. They shall record and give reasons for all decisions. The national safety authority’s overall assessment process shall be periodically internally reviewed and continuously improved to secure its continued effectiveness and efficiency.(b)Quality of the assessment processNational safety authorities shall monitor the quality of their own performance at key stages in the processing of applications for safety certificates.(c)Scope of the assessmentThe assessment shall be at management-system level and process-driven. Where scrutiny reveals shortcomings, the national safety authority may exercise discretion and, depending on the nature and seriousness of the non-conformity, shall outline the points which need to be enhanced. Ultimately, the national safety authority shall exercise its power to reject an application.The assessment shall be:appropriate to the risks, character and extent of operations of the applicant;based on judgments of the railway undertaking’s overall ability to operate safely as described in its safety management system.(d)Timing of the assessmentNational safety authorities shall complete the assessment within the time period required by Article 12 of Directive 2004/49/EC whilst ensuring that the evidence provided by the applicant is sufficiently examined. The national safety authority shall inform railway undertakings of issues of major concern as early as practically possible during the assessment phase.(e)Decision making during the assessmentA decision to accept or reject an application for a safety certificate or authorisation shall be based on the evidence provided by the applicant and on whether compliance with the relevant requirements has been shown or not.2.The national safety authority shall assess whether the application for a safety certificate complies with Commission Regulation (EC) No 653/2007OJ L 153, 14.6.2007, p. 9..3.In particular, the national safety authority shall assess whether the attached summary of the safety management system manual allows an initial judgment on the quality and appropriateness of the safety management system and shall decide in which areas further information is necessary. The national safety authority may, as part of this request for more information, seek as much detailed information as it deems reasonably necessary to help its assessment of the application.4.When granting a safety certificate, compliance of the applicant’s safety management system with the assessment criteria shall be documented in relation to each assessment criterion.5.When identifying a point of query or possible non-compliance, the national safety authority shall be specific and help the applicant to understand the level of detail expected in the response. To do this it shall:(a)refer accurately to the relevant criteria and ensure that the applicant has understood clearly the identified areas of non-compliance;(b)identify the relevant part of related regulations, rules, and standards;(c)state why the assessment criterion is not met;(d)agree on further commitments, information and any supporting evidence to be provided, as required by the level of detail of the criterion, and specify both the action required by the applicant to rectify the deficiency and the timeframe for compliance;(e)specify areas which could be subject to further scrutiny through supervision after the award of the certificate.6.If a railway undertaking applies for both Part A and Part B safety certificates at the same time, the national safety authority shall ensure that the Part A certificate is granted first or that both certificates are granted together as provided for in Regulation (EC) No 653/2007. Nevertheless, national safety authorities shall define a procedure for how to use the application form (in particular, the front page for the Annexes) if a new application is made for both certificates at the same time.7.The general framework procedures in place for assessing applications for safety certificates shall also apply to applications for safety certificates as referred to in Article 10(2)(b) of Directive 2004/49/EC.8.A national safety authority’s assessment of an application for a safety certificate as referred to in Article 10(2)(b) Directive 2004/49/EC shall only apply to a railway undertaking’s ability to comply with the requirements needed to operate on the specific network for which it is seeking a certificate by using the procedures it has established to obtain a Part A certificate.9.These assessment criteria are based on showing that the results of applying the procedures or processes to manage operation on a specific network have been documented and the commitment to implement them has been made. Hence in order to check whether the criteria have been met, the national safety authority may request that the railway undertaking submit a sample of the documentation it plans to use.10.National safety authorities shall cooperate to address issues of non-compliance with the Part B assessment criteria or to deal with queries on the Part B application. A national safety authority assessing a Part B application shall liaise with the national safety authority that issued Part A to discuss and agree what action, if any, each one will take to ensure compliance with the Part B assessment criteria.ANNEX IICriteria for assessing conformity with the requirements for obtaining safety certificates to be issued in accordance with Article 10(2)(a) of Directive 2004/49/EC related to the railway undertaking’s safety management system as described in Article 9 and Annex III of that DirectiveA.RISK CONTROL MEASURES FOR ALL RISKS ASSOCIATED WITH THE ACTIVITY OF THE RAILWAY UNDERTAKINGArticle 9(2) of Directive 2004/49/EC.A.1There are procedures put in place to identify risks associated with railway operations, including those directly arising from work activities, job design or workload and the activities of other organisations/persons.A.2There are procedures in place to develop and put in place risk control measures.A.3There are procedures in place to monitor the effectiveness of risk control arrangements and to implement changes when required.A.4There are procedures in place to recognise the need to work together with other entities (such as the infrastructure manager, railway undertakings, the manufacturer, the maintenance supplier, the entity in charge of maintenance, the railway vehicle keeper, the service provider and the procurement entity), where appropriate, on issues where they have shared interfaces that are likely to affect the putting in place of adequate risk control measures in accordance with Article 4(3) of Directive 2004/49/EC.A.5There are procedures for agreed documentation and communication with the relevant entities including the identification of roles and responsibilities of each participating organisation and the specifications for information exchanges.A.6There are procedures to monitor the effectiveness of these arrangements and to implement changes when required.B.RISK CONTROL RELATED TO THE SUPPLY OF MAINTENANCE AND MATERIALArticle 9(2) of Directive.2004/49/EC.B.1There are procedures to derive maintenance requirements/standards/processes from safety data and from the assignment of rolling stock.B.2There are procedures to adapt maintenance intervals according to the type and extent of service performed and/or data from rolling stock.B.3There are procedures to ensure that the responsibility for maintenance is clearly defined, to identify the competencies required for maintenance posts and to allocate appropriate levels of responsibility.B.4There are procedures to collect information on malfunctions and defects arising from day-to-day operation and to report them to those responsible for maintenance.B.5There are procedures to identify and report risks arising from defects and construction non-conformities or malfunctions throughout the lifecycle to interested parties.B.6There are procedures to verify and control the performance and results of maintenance to ensure that they comply with corporate standards.C.RISK CONTROL RELATED TO THE USE OF CONTRACTORS AND CONTROL OF SUPPLIERSArticle 9(2) of Directive 2004/49/EC.C.1There are procedures to verify the competence of contractors (including subcontractors) and suppliers.C.2There are procedures to verify and control the safety performance and results of all contracted services and products supplied either by the contractor or supplier to ensure that they comply with the requirements set out in the contract.C.3Responsibilities and tasks relating to railway safety issues are clearly defined, known and allocated between the contracting partners and among all other interested parties.C.4There are procedures to ensure traceability of safety-related documents and contracts.C.5There are procedures to ensure that safety tasks, including the exchange of safety-related information, are performed by the contractors or the supplier according to relevant requirements set out in the contract.D.RISKS ARISING FROM THE ACTIVITIES OF OTHER PARTIES EXTERNAL TO THE RAILWAY SYSTEMArticle 9(2) of Directive 2004/49/EC.D.1There are procedures to identify potential risks from parties external to the railway system where appropriate and reasonable.D.2There are procedures to establish control measures to mitigate the risks identified under D1 insofar as the responsibilities of the applicant are concerned.D.3There are procedures to monitor the effectiveness of the measures identified under D2 and implement changes where appropriate.E.DOCUMENTATION OF THE SAFETY MANAGEMENT SYSTEME.1There is a description of the activity that makes clear the type, extent and risk of operation.E.2There is a description of the structure of the safety management system, including the allocation of roles and responsibilities.E.3There is a description of safety management system procedures required by Article 9 and Annex III of Directive 2004/49/EC consistent with the type and extent of services operated.E.4Safety-critical processes and tasks relevant to the type of activity/service are listed and briefly described.F.DISTRIBUTION OF RESPONSIBILITIESAnnex III to Directive 2004/49/EC, point 1.F.1There is a description of how coordination of safety management system activities across the organisation is ensured, based on proven knowledge and lead responsibility at management level.F.2There are procedures to ensure that staff with delegated responsibilities within the organisation have the authority, competence and appropriate resources to fulfil their duty.F.3Safety-related areas of responsibility, and the distribution of responsibilities to specific functions associated with them, together with their interfaces, are clearly defined.F.4There is a procedure to ensure that safety tasks are clearly defined and delegated to staff with appropriate competence.G.SECURING CONTROL BY THE MANAGEMENT ON DIFFERENT LEVELSAnnex III to Directive 2004/49/EC, point 1.G.1There is a description of how responsibilities are allocated for each safety-related process throughout the organisation.G.2There is a procedure for regular monitoring of task performance assured by the line management chain that must intervene if the tasks are not being properly performed.G.3There are procedures to identify and manage the impact of other management activities on the safety management system.G.4There are procedures to hold those with a role in the management of safety accountable for their performance.G.5There are procedures to allocate resources to deliver the tasks under the safety management system.H.INVOLVING STAFF AND THEIR REPRESENTATIVES ON ALL LEVELSAnnex III to Directive 2004/49/EC, point 1.H.1There are procedures in place to ensure that staff and staff representatives are adequately represented and consulted in defining, proposing, reviewing and developing the safety aspects of operational procedures that may involve staff.H.2Staff involvement and consultation arrangements are documented.I.ENSURING CONTINUOUS IMPROVEMENTAnnex III to Directive 2004/49/EC, point 1.There are procedures in place to ensure, where reasonably practicable, the continuous improvement of the safety management system; these shall include:(a)procedures for periodic reviews of the safety management system, as found to be necessary;(b)procedures for describing arrangements to monitor and analyse relevant safety data;(c)procedures for describing how identified shortcomings are rectified;(d)procedures for describing the implementation of new safety management rules based on development and lessons learnt;(e)procedures for describing how internal audit findings are used to bring about improvement in the safety management system.J.SAFETY POLICY APPROVED BY THE ORGANISATION’S CHIEF EXECUTIVE AND COMMUNICATED TO ALL STAFFAnnex III to Directive 2004/49/EC, point 2(a).A document describing the organisation’s safety policy exists and is:(a)communicated and made available to all staff, e.g. via the organisation’s intranet;(b)appropriate to the type and extent of service;(c)approved by the organisation’s chief executive.K.QUALITATIVE AND QUANTATIVE TARGETS OF THE ORGANISATION FOR MAINTAINING AND ENHANCING SAFETY, AND PLANS AND PROCEDURES FOR REACHING THESE TARGETSAnnex III to Directive 2004/49/EC, point 2(b).K.1There are procedures to determine relevant safety targets in line with the legal framework, and there is a document stating these targets.K.2There are procedures to determine relevant safety targets consistent with the type and extent of the railway operations covered and the relevant risks.K.3There are procedures to regularly assess overall safety performance in relation to the organisation’s corporate safety targets and to those established on member state level.K.4There are procedures in place to regularly monitor and review operational arrangements by:(a)collecting relevant safety data to derive trends in safety performance and assess compliance with targets;(b)interpreting relevant data and implementing necessary changes.K.5There are procedures in place by the railway undertaking to develop plans and procedures for reaching its targets.L.PROCEDURES TO MEET EXISTING, NEW AND ALTERED TECHNICAL AND OPERATIONAL STANDARDS OR OTHER PRESCRIPTIVE CONDITIONSAnnex III to Directive 2004/49/EC, point 2(c).L.1For safety related requirements relevant to the type and extent of operations, there are procedures for:(a)identifying these requirements and updating relevant procedures to reflect changes made to them (change control management);(b)implementing them;(c)monitoring compliance with them;(d)taking actions when non-compliance is identified.L.2There are procedures in place to ensure that the right staff, procedures, specific documents, equipment and rolling stock are used for the purpose intended.L.3The safety management system has procedures in place to ensure that maintenance is carried out according to the relevant requirements.M.PROCEDURES AND METHODS FOR CARRYING OUT RISK EVALUATION AND IMPLEMENTING RISK CONTROL MEASURES WHENEVER A CHANGE OF THE OPERATING CONDITIONS OR NEW MATERIAL IMPOSES NEW RISKS ON THE INFRASTRUCTURE OR ON OPERATIONAnnex III to Directive 2004/49/EC, point 2(d).M.1There are management procedures for changes in equipment, procedures, organisation, staffing or interfaces.M.2There are risk assessment procedures to manage changes and to apply the common safety method on risk evaluation and assessment as set out in Commission Regulation (EC) No 352/2009OJ L 108, 29.4.2009, p. 4. when required.M.3The railway undertaking has procedures in place to feed the results of risk assessment into other processes within the organisation and make them visible to relevant staff.N.PROVISION OF STAFF TRAINING PROGRAMMES AND SYSTEMS TO ENSURE THAT THE STAFF COMPETENCE IS MAINTAINED AND TASKS CARRIED OUT ACCORDINGLYAnnex III to Directive 2004/49/EC, point 2(e).N.1There is a competence management system that includes at least:(a)identification of the knowledge and skills required for safety related tasks;(b)selection principles (basic educational level, mental aptitude and physical fitness required);(c)initial training and certification of acquired competence and skills;(d)ongoing training and periodical update of existing knowledge and skills;(e)periodic checks of competence where appropriate;(f)special measures in case of accidents/incidents or long absence from work, as required/where appropriate;(g)specific safety management system training for staff directly involved in ensuring that the safety management system works.N.2There are procedures within the competence management system providing for:(a)the identification of posts that perform safety tasks;(b)the identification of posts that entail responsibilities for taking operational decisions within the safety management system;(c)staff to have the necessary knowledge, skills and aptitude (medical and psychological) appropriate to their tasks and periodically undergo retraining;(d)allocating staff with the competence appropriate to relevant tasks;(e)monitoring how tasks are performed and implementing corrective actions where required.O.ARRANGEMENTS FOR THE PROVISION OF SUFFICIENT INFORMATION WITHIN THE ORGANISATION AND, WHERE APPROPRIATE, BETWEEN ORGANISATIONS OPERATING ON THE SAME INFRASTRUCTUREAnnex III to Directive 2004/49/EC, point 2(f).O.1There are procedures to ensure that:(a)staff have knowledge and understanding of the safety management system and information is easily accessible; and(b)appropriate documentation on the safety management system is given to relevant safety personnel.O.2There are procedures to ensure that:(a)key operational information is relevant and valid;(b)staff are aware of its existence before it is applied;(c)it is available to staff and where required copies are formally given to them.O.3There are arrangements in place for the sharing of information between railway organisations.P.PROCEDURES AND FORMATS FOR DOCUMENTING SAFETY INFORMATION, AND DESIGNATION OF A PROCEDURE FOR CONFIGURATION CONTROL OF VITAL SAFETY INFORMATIONAnnex III to Directive 2004/49/EC, point 2(g).P.1There are procedures to ensure that all relevant safety information is accurate, complete, consistent, easy to understand, appropriately updated, and duly documented.P.2There are procedures to:(a)format, generate, distribute and manage control of changes to all relevant safety documentation;(b)receive, collect and store all relevant documentation/information on paper or by other registration systems.P.3There is a procedure for configuration control of vital safety information.Q.PROCEDURES TO ENSURE THAT ACCIDENTS, INCIDENTS, NEAR MISSES AND OTHER DANGEROUS OCCURRENCES ARE REPORTED, INVESTIGATED AND ANALYSED AND THAT NECESSARY PREVENTIVE MEASURES ARE TAKENAnnex III to Directive 2004/49/EC, point 2(h).Q.1There are procedures to ensure that accidents, incidents, near misses and other dangerous occurrences:(a)are reported, logged, investigated and analysed;(b)are reported, as required by relevant legislation, to national bodies.Q.2There are procedures to ensure that:(a)recommendations from the national safety authority, from the national investigating body, and from industry/internal investigations are evaluated and implemented if appropriate or mandated;(b)relevant reports/information from other railway undertakings, infrastructure managers, entities in charge of maintenance and railway vehicle keepers are considered and taken into account.Q.3There are procedures for relevant information relating to the investigation and causes of accidents, incidents, near misses and other dangerous occurrences to be used to learn and, where required, to adopt preventive measures.R.PROVISION OF PLANS FOR ACTION AND ALERTS AND INFORMATION IN CASE OF EMERGENCY, AGREED UPON WITH THE APPROPRIATE PUBLIC AUTHORITIESAnnex III to Directive 2004/49/EC, point 2(i).R.1A document identifies all types of emergency, including degraded operations, and there are procedures in place to identify new ones.R.2There are procedures in place to ensure that, for each identified type of emergency:(a)the emergency services can be promptly contacted;(b)the emergency services are provided with all relevant information both in advance, to prepare their emergency response, and at the time of an emergency.R.3The roles and responsibilities of all parties are identified and set out in a document.R.4Plans for action, alerts and information exist and include:(a)procedures to alert all staff with responsibility for emergency management;(b)arrangements to communicate these to all parties, including emergency instructions for passengers;(c)arrangements for contacting competent staff immediately so they can take any decisions required.R.5There is a document describing how resources and means have been allocated and how training requirements have been identified.R.6There are procedures in place to re-establish normal operating conditions as soon as possible.R.7There are procedures for testing emergency plans in cooperation with other parties to train staff, test procedures, identify weak points and verify how potential emergency situations are managed.R.8There are procedures to ensure that competent staff in charge (particularly relating to dangerous goods services), with adequate language skills, can be contacted easily and without delay by the infrastructure manager.R.9There is a procedure to contact the entity in charge of maintenance or the railway vehicle keeper in the event of an emergency.S.PROVISIONS FOR RECURRENT INTERNAL AUDITING OF THE SAFETY MANAGEMENT SYSTEMAnnex III to Directive 2004/49/EC, point 2(j).S.1There is an internal auditing system which is independent and impartial and which acts in a transparent way.S.2There is a schedule of planned internal audits which can be revised depending on the results of previous audits and monitoring of performance.S.3There are procedures in place to identify and select suitably competent auditors.S.4Procedures are in place to:(a)analyse and evaluate the results of the audits;(b)recommend follow-up measures;(c)follow up the effectiveness of measures;(d)document the execution of audits and the results of audits.S.5There are procedures to ensure that senior levels of the management chain are aware of the results of audits and take overall responsibility for implementation of changes to the safety management system.S.6There is a document showing how audits are planned in relation to routine monitoring arrangements to ensure compliance with internal procedures and standards.ANNEX IIICriteria for assessing conformity with the requirements for obtaining safety certificates to be issued in accordance with Article 10(2)(b) of the Directive 2004/49/ECGENERALThe service for which a Part B certificate is being sought is outlined and there is a description of how the railway undertaking’s generic procedures devised in support of its certificate issued in accordance with Article 10(2)(a) of Directive 2004/49/EC are applied to develop all the arrangements (including allocation of resources) put in place to deliver the service.A.COMPLIANCE WITH NETWORK-SPECIFIC RULESAnnex IV to Directive 2004/49/EC, first indent.A.1There are documents containing results to show that the specific rules and specific risks associated with operating on the network for which a Part B application is being submitted have been considered and to show that the railway undertaking can comply with any network-specific rules and any exceptions to or derogations from those rules.A.2Network interfaces with other parties involved in railway operation on the network concerned are identified.A.3There are documents showing how the railway undertaking will interact with the infrastructure manager (IM) for the network and other railway undertakings operating on the network, including details on how information is shared.A.4There are documents showing how the railway undertaking will deal with emergency situations, including coordination with the infrastructure manager and the relevant public authorities.A.5There are documents identifying any specific accident/incident investigation rules and showing that the applicant can comply with them.B.COMPLIANCE WITH NETWORK-SPECIFIC REQUIREMENTS FOR STAFF COMPETENCEAnnex IV to Directive 2004/49/EC, second indent.B.1The documentation demonstrates that the applicant’s safety management system contains a competence management system to:(a)identify the categories of staff (employed or contracted) involved in providing the service and(b)deliver competent staff for the network concerned, especially for those staff who are asked to undertake a variety of tasks and assure certification where appropriate.B.2The documentation demonstrates that there are arrangements put in place to organise the day-to-day work of the staff to ensure that safety-related tasks are carried out and that staff are assigned to appropriate tasks.B.3The documentation demonstrates the applicant’s ability to produce documents to be used in training the relevant staff and its ability to ensure that the documents will be accurate, be kept up to date and be in a language and terminology understood by the staff who need to use them.C.COMPLIANCE WITH NETWORK-SPECIFIC REQUIREMENTS FOR MANAGEMENT OF ROLLING STOCKAnnex IV to Directive 2004/49/EC, third indent.C.1In the documentation, the types of rolling stock to be used on the specific network and the type of operations to be conducted are clearly indicated.C.2The documentation outlines how the railway undertaking complies with any operational restrictions placed on the type of rolling stock used on the network.C.3In the documentation, any additional maintenance requirements for the network concerned are identified and appropriate arrangements for maintenance are in place.C.4In the documentation, any additional requirements to manage rolling stock incidents for the network concerned are identified and appropriate arrangements are put in place.ANNEX IVPrinciples for supervision after the award of a Part A or Part B certificate1.The approach of national safety authorities to supervision of railway undertakings’ compliance as referred to in Article 4(1) and 16(2)(e) of Directive 2004/49/EC shall be based on the following principles. These principles apply to the framework of supervision activities as a whole and to individual cases within that framework.2.National safety authorities shall apply the principle of proportionality between enforcement and risk. Action taken by a national safety authority to achieve compliance or bring railway undertakings to account for not meeting their legal obligations shall be proportionate to any risks to safety or to the potential seriousness of any non-compliance, including any actual or potential harm.3.National safety authorities shall apply the principle of consistency of approach to ensure that a national safety authority takes a similar approach in similar circumstances to achieve similar ends.4.National safety authority supervision activity shall be targeted primarily at those activities which a national safety authority believes give rise to the most serious risks or where the hazards are least well-controlled. To do so, the national safety authority shall have methods and power to assess the day-to-day performance of the railway undertaking.5.National safety authorities shall decide on priorities to use their resources effectively but the decision on how best to do that should rest with each individual national safety authority. Action shall be focused on those who are responsible for the risk and who are best placed to control it.6.National safety authorities shall apply the principle of transparency to help railway undertakings understand what is expected of them (including what they should or should not do) and what they should expect from the national safety authority.7.National safety authorities shall be accountable for their decisions in accordance with Article 17(3) of Directive 2004/49/EC. National safety authorities shall therefore have policies and principles by which they can be assessed. Moreover, national safety authorities shall also have a complaints procedure.8.National safety authorities shall develop cooperation arrangements between each other in order to share information with each other and to coordinate their response to any breaches of safety. This is particularly important for Part B safety certificates. In addition, national safety authorities shall develop cooperation arrangements with other competent authorities in order to share information and to develop unified approaches to issues that impinge on railway safety.

Amendments and corrections
October 30, 2025	Repealed by 32018R0762 and 32020R0782
December 30, 2010	Entry into force - Date pub. +20 See Art 5

Commission Regulation (EU) No 1158/2010 of 9 December 2010 on a common safety method for assessing conformity with the requirements for obtaining railway safety certificates Text with EEA relevance