Article 1Subject matter and scope1.This Regulation establishes requirements for the labelling of and the provision of supplementary product information on electric mains-operated household washing machines and electric mains-operated household washing machines that can also be powered by batteries, including those sold for non-household use and built-in household washing machines.2.This Regulation shall not apply to household combined washer-driers.

Article 2DefinitionsIn addition to the definitions laid down in Article 2 of Directive 2010/30/EU, the following definitions shall apply for the purposes of this Regulation:(1)"household washing machine" means an automatic washing machine which cleans and rinses textiles using water, which also has a spin extraction function and which is designed to be used principally for non-professional purposes;(2)"built-in household washing machine" means a household washing machine intended to be installed in a cabinet, a prepared recess in a wall or a similar location, requiring furniture finishing;(3)"automatic washing machine" means a washing machine where the load is fully treated by the machine without the need for user intervention at any point during the programme;(4)"household combined washer-drier" means a household washing machine which includes both a spin extraction function and also a means for drying the textiles, usually by heating and tumbling;(5)"programme" means a series of operations that are pre-defined and which are declared by the supplier as suitable for washing certain types of textile;(6)"cycle" means a complete washing, rinsing and spinning process, as defined for the selected programme;(7)"programme time" means the time that elapses from the initiation of the programme until the completion of the programme excluding any end-user programmed delay;(8)"rated capacity" means the maximum mass in kilograms stated by the supplier at 0,5 kg intervals of dry textiles of a particular type, which can be treated in a household washing machine on the selected programme, when loaded in accordance with the supplier’s instructions;(9)"partial load" means half of the rated capacity of a household washing machine for a given programme;(10)"remaining moisture content" means the amount of moisture contained in the load at the end of the spinning phase;(11)"off-mode" means a condition where the household washing machine is switched off using appliance controls or switches accessible to and intended for operation by the end-user during normal use to attain the lowest power consumption that may persist for an indefinite time while the household washing machine is connected to a power source and used in accordance with the supplier’s instructions; where there is no control or switch accessible to the end-user, "off-mode" means the condition reached after the household washing machine reverts to a steady-state power consumption on its own;(12)"left-on mode" means the lowest power consumption mode that may persist for an indefinite time after completion of the programme without any further intervention by the end-user besides unloading of the household washing machine;(13)"equivalent household washing machine" means a model of household washing machine placed on the market with the same rated capacity, technical and performance characteristics, energy and water consumption and airborne acoustical noise emissions during washing and spinning as another model of household washing machine placed on the market under a different commercial code number by the same supplier;(14)"end-user" means a consumer buying or expected to buy a household washing machine;(15)"point of sale" means a location where household washing machines are displayed or offered for sale, hire or hire-purchase.

Article 3Responsibilities of suppliersSuppliers shall ensure that:(a)each household washing machine, is supplied with a printed label in the format and containing information as set out in Annex I;(b)a product fiche, as set out in Annex II, is made available;(c)the technical documentation as set out in Annex III is made available on request to the authorities of the Member States and to the Commission;(d)any advertisement for a specific model of household washing machine contains the energy efficiency class, if the advertisement discloses energy-related or price information;(e)any technical promotional material concerning a specific model of household washing machine which describes its specific technical parameters includes the energy efficiency class of that model;(f)an electronic label in the format and containing the information set out in Annex I is made available to dealers for each household washing machine model placed on the market from 1 January 2015 with a new model identifier. It may also be made available to dealers for other household washing machine models;(g)an electronic product fiche as set out in Annex II is made available to dealers for each household washing machine model placed on the market from 1 January 2015 with a new model identifier. It may also be made available to dealers for other household washing machine models.

Article 4Responsibilities of dealersDealers shall ensure that:(a)each household washing machine, at the point of sale, bears the label provided by suppliers in accordance with Article 3(a) on the outside of the front or top of the household washing machine, in such a way as to be clearly visible;(b)household washing machines offered for sale, hire or hire-purchase where the end-user cannot be expected to see the product displayed are marketed with the information to be provided by suppliers in accordance with Annex IV. Where the offer is made through the internet and an electronic label and an electronic product fiche have been made available in accordance with Article 3(f) and 3(g) the provisions of Annex VIII shall apply instead;(c)any advertisement for a specific model of household washing machine contains a reference to its energy efficiency class, if the advertisement discloses energy-related or price information;(d)any technical promotional material concerning a specific model of household washing machine, which describes its specific technical parameters includes a reference to the energy efficiency class of that model.

Article 5Measurement methodsThe information to be provided pursuant to Articles 3 and 4 shall be obtained by reliable, accurate and reproducible measurement procedures, which take into account the recognised state-of-the-art measurement methods.

Article 6Verification procedure for market surveillance purposesMember States shall apply the procedure laid down in Annex V when assessing the conformity of the declared energy efficiency class, the annual energy consumption, annual water consumption, spin-drying efficiency class, power consumption in off-mode and left-on mode, duration of the left-on mode, remaining moisture content, spin speed and airborne acoustical noise emissions.

Article 7RevisionThe Commission shall review this Regulation in the light of technological progress no later than four years after its entry into force. The review shall in particular assess the verification tolerances set out in Annex V.

Article 8RepealDirective 95/12/EC shall be repealed from 20 December 2011.

Article 9Transitional provisions1.Articles 3(d), (e), 4(b), (c) and (d) shall not apply to printed advertisements and printed technical promotional material published before 20 April 2012.2.Household washing machines placed on the market before 20 December 2011 shall comply with the provisions set out in Directive 95/12/EC.3.If an implementing measure for Directive 2009/125/EC of the European Parliament and of the CouncilOJ L 285, 31.10.2009, p. 10. with regards to ecodesign requirements for household washing machines was adopted, household washing machines, which comply with the provisions of this implementing measure with respect to the washing efficiency requirements and with the provisions of this Regulation, and which are placed on the market or offered for sale, hire or hire-purchase before 20 December 2011 shall be regarded as complying with the requirements of Directive 95/12/EC.

Article 10Entry into force and application1.This Regulation shall enter into force on the 20th day following its publication in the Official Journal of the European Union.2.It shall apply from 20 December 2011. However, Articles 3(d), (e), 4(b), (c) and (d) shall apply from 20 April 2012.

This Regulation shall be binding in its entirety and directly applicable in all Member States.ANNEX ILabel1.LABEL(1)The following information shall be included in the label:I.supplier’s name or trade mark;II.supplier’s model identifier, meaning the code, usually alphanumeric, which distinguishes a specific household washing machine model from other models with the same trade mark or supplier’s name;III.the energy efficiency class determined in accordance with point 1 of Annex VI; the head of the arrow containing the energy efficiency class of the household washing machine shall be placed at the same height as the head of the arrow of the relevant energy efficiency class;IV.weighted annual energy consumption (AEC) in kWh per year, rounded up to the nearest integer in accordance with Annex VII;V.weighted annual water consumption (AWC), in litres per year, rounded up to the nearest integer in accordance with Annex VII;VI.rated capacity, in kg, for the standard 60 °C cotton programme at full load or the standard 40 °C cotton programme at full load, whichever is the lower;VII.the spin-drying efficiency class as set out in point 2 of Annex VI;VIII.airborne acoustical noise emissions, during the washing and spinning phases, for the standard 60 °C cotton programme at full load, expressed in dB(A) re 1 pW, rounded to the nearest integer.(2)The design of the label shall be in accordance with point 2. By way of derogation, where a model has been awarded an "EU Ecolabel" under Regulation (EC) No 66/2010 of the European Parliament and of the CouncilOJ L 27, 30.1.2010, p. 1., a copy of the EU Ecolabel may be added.2.LABEL DESIGNThe design of the label shall be as in the figure below.Whereby:(a)The label must be at least 110 mm wide and 220 mm high. Where the label is printed in a larger format, its content must nevertheless remain proportionate to the specifications above.(b)The background shall be white.(c)Colours shall be CMYK — cyan, magenta, yellow and black, following this example: 00-70-X-00: 0 % cyan, 70 % magenta, 100 % yellow, 0 % black.(d)The label shall fulfil all of the following requirements (numbers refer to the figure above):Border stroke: 5 pt — colour: Cyan 100 % — round corners: 3,5 mm.EU logo — colours: X-80-00-00 and 00-00-X-00.Energy logo: colour: X-00-00-00.Pictogram as depicted: EU logo and energy logo (combined): width: 92 mm, height: 17 mm.Sub-logos border: 1 pt — colour: Cyan 100 % — length: 92,5 mm.A-G scaleArrow: height: 7 mm, gap: 0,75 mm — colours:Highest class: X-00-X-00,Second class: 70-00-X-00,Third class: 30-00-X-00,Fourth class: 00-00-X-00,Fifth class: 00-30-X-00,Sixth class: 00-70-X-00,Last class: 00-X-X-00.Text: Calibri bold 18 pt, capitals and white; "+" symbols: Calibri bold 12 pt, capitals, white, aligned on a single row.Energy efficiency classArrow: width: 26 mm, height: 14 mm, 100 % black.Text: Calibri bold 29 pt, capitals and white; "+" symbols: Calibri bold 18 pt, capitals, white, aligned on a single row.Energy: text: Calibri regular 11 pt, capitals, 100 % black.Weighted annual energy consumptionBorder: 2 pt — colour: Cyan 100 % — round corners: 3,5 mm.Value: Calibri bold 42 pt, 100 % black; and Calibri regular 17 pt, 100 % black.Weighted annual water consumptionPictogram as depictedBorder: 2 pt — colour: Cyan 100 % — round corners: 3,5 mm.Value: Calibri bold 24 pt, 100 % black; and Calibri regular 16 pt, 100 % black.Rated capacityPictogram as depictedBorder: 2 pt — colour: Cyan 100 % — round corners: 3,5 mm.Value: Calibri bold 24 pt, 100 % black; and Calibri regular 16 pt, 100 % black.Spin-drying efficiency classPictogram as depictedBorder: 2 pt — colour: Cyan 100 % — round corners: 3,5 mm.Value: Calibri regular 16 pt, horizontal scale 75 %, 100 % black and Calibri Bold 22 pt, horizontal scale 75 %, 100 % black.Airborne acoustical noise emissionsPictograms as depictedBorder: 2 pt — colour: Cyan 100 % — round corners: 3,5 mm.Value: Calibri bold 24 pt, 100 % black; and Calibri regular 16 pt, 100 % black.Supplier’s name or trade markSupplier’s model identifierThe supplier’s name or trademark and model identifier should fit in a space of 92 × 15 mm.Numbering of the Regulation: Calibri bold 12 pt, 100 % black.ANNEX IIProduct Fiche1.The information in the product fiche of the household washing machine shall be provided in the following order and shall be included in the product brochure or other literature provided with the product:(a)supplier’s name or trade mark;(b)supplier’s model identifier, meaning the code, usually alphanumeric, which distinguishes a specific household washing machine model from other models with the same trade mark or supplier’s name;(c)rated capacity in kg of cotton for the standard 60 °C cotton programme at full load or the 40 °C cotton programme at full load, whichever is the lower;(d)energy efficiency class in accordance with point 1 of Annex VI;(e)where the household washing machine has been awarded an "EU Ecolabel award" under Regulation (EC) No 66/2010, this information may be included;(f)weighted annual energy consumption (AEC) in kWh per year, rounded up to the nearest integer; it shall be described as: "Energy consumption "X" kWh per year, based on 220 standard washing cycles for cotton programmes at 60 °C and 40 °C at full and partial load, and the consumption of the low-power modes. Actual energy consumption will depend on how the appliance is used.";(g)the energy consumption (Et,60, Et,60½, Et,40½) of the standard 60 °C cotton programme at full load and partial load and of the standard 40 °C cotton programme at partial load;(h)weighted power consumption of the off-mode and of the left-on mode;(i)weighted annual water consumption (AWC) in litres per year, rounded up to the nearest integer; it shall be described as: "Water consumption "X" litres per year, based on 220 standard washing cycles for cotton programmes at 60 °C and 40 °C at full and partial load. Actual water consumption will depend on how the appliance is used.";(j)spin-drying efficiency class determined in accordance with point 2 of Annex VI, expressed as "spin-drying efficiency class "X" on a scale from G (least efficient) to A (most efficient)"; this may be expressed by other means provided it is clear that the scale is from G (least efficient) to A (most efficient);(k)maximum spin speed attained for the standard 60 °C cotton programme at full load or the standard 40 °C cotton programme at partial load, whichever is the lower, and remaining moisture content attained for the standard 60 °C cotton programme at full load or the standard 40 °C cotton programme at partial load, whichever is the greater;(l)indication that the "standard 60 °C cotton programme" and the "standard 40 °C cotton programme" are the standard washing programmes to which the information in the label and the fiche relates, that these programmes are suitable to clean normally soiled cotton laundry and that they are the most efficient programmes in terms of combined energy and water consumption;(m)the programme time of the "standard 60 °C cotton programme" at full and partial load and of the "standard 40 °C cotton programme" at partial load in minutes and rounded to the nearest minute;(n)the duration of the left-on mode (Tl) if the household washing machine is equipped with a power management system;(o)airborne acoustical noise emissions expressed in dB(A) re 1 pW and rounded to the nearest integer during the washing and spinning phases for the standard 60 °C cotton programme at full load;(p)if the household washing machine is intended to be built-in, an indication to this effect.2.One fiche may cover a number of household washing machine models supplied by the same supplier.3.The information contained in the fiche may be given in the form of a copy of the label, either in colour or in black and white. Where this is the case, the information listed in point 1 not already displayed on the label shall also be provided.ANNEX IIITechnical documentation1.The technical documentation referred to in Article 3(c) shall include:(a)the name and address of the supplier;(b)a general description of the washing machine model, sufficient for it to be unequivocally and easily identified;(c)where appropriate, the references of the harmonised standards applied;(d)where appropriate, the other technical standards and specifications used;(e)identification and signature of the person empowered to bind the supplier;(f)an indication stating whether the household washing machine model releases or not silver ions during the washing cycle as follows: "This product releases/does not release silver ions during the washing cycle.";(g)technical parameters for measurements as follows:(i)energy consumption;(ii)programme time;(iii)water consumption;(iv)power consumption in "off-mode";(v)power consumption in "left-on mode";(vi)"left-on mode" duration;(vii)remaining moisture content;(viii)airborne acoustical noise emissions;(ix)maximum spin speed;(h)the results of calculations performed in accordance with Annex VII.2.Where the information included in the technical documentation file for a particular household washing machine model has been obtained by calculation on the basis of design, or extrapolation from other equivalent household washing machines or both, the documentation shall include details of such calculations or extrapolations, or both, and of tests undertaken by suppliers to verify the accuracy of the calculations undertaken. The information shall also include a list of all other equivalent household washing machine models where the information was obtained on the same basis.ANNEX IVInformation to be provided in the cases where end-users cannot be expected to see the product displayed1.The information referred to in Article 4(b) shall be provided in the following order:(a)the rated capacity in kg of cotton, for the standard 60 °C cotton programme at full load or the standard 40 °C cotton programme at full load, whichever is the lower;(b)the energy efficiency class as defined in point 1 of Annex VI;(c)the weighted annual energy consumption in kWh per year, rounded up to the nearest integer and calculated in accordance with point 1(c) of Annex VII;(d)the weighted annual water consumption in litres per year, rounded up to the nearest integer and calculated in accordance with point 2(a) of Annex VII;(e)the spin-drying efficiency class in accordance with point 2 of Annex VI;(f)the maximum spin speed attained for the standard 60 °C cotton programme at full load or the standard 40 °C cotton programme at partial load, whichever is the lower, and the remaining moisture content attained for the standard 60 °C cotton programme at full load or the standard 40 °C cotton programme at partial load, whichever is the greater;(g)airborne acoustical noise emissions during the washing and spinning phases, for the standard 60 °C cotton programme at full load, expressed in dB(A) re 1 pW and rounded to the nearest integer;(h)if the household washing machine is produced in order to be built-in, an indication to this effect.2.Where other information contained in the product fiche is also provided, it shall be in the form and order specified in Annex II.3.The size and font, in which all the information referred in this Annex is printed or shown, shall be legible.ANNEX VProduct compliance verification by market surveillance authoritiesThe verification tolerances set out in this Annex relate only to the verification of the measured parameters by Member State authorities and shall not be used by the supplier as an allowed tolerance to establish the values in the technical documentation. The values and classes on the label or in the product fiche shall not be more favourable for the supplier than the values reported in the technical documentation.When verifying the compliance of a product model with the requirements laid down in this Delegated Regulation, for the requirements referred to in this Annex, the authorities of the Member States shall apply the following procedure:(1)The Member State authorities shall verify one single unit of the model.(2)The model shall be considered to comply with the applicable requirements if:(a)the values given in the technical documentation pursuant to Article 5(b) of Directive 2010/30/EU (declared values), and, where applicable, the values used to calculate these values, are not more favourable for the supplier than the corresponding values given in the test reports pursuant to point (iii) of the abovementioned Article; and(b)the values published on the label and in the product fiche are not more favourable for the supplier than the declared values, and the indicated energy efficiency class is not more favourable for the supplier than the class determined by the declared values; and(c)when the Member State authorities test the unit of the model, the determined values (the values of the relevant parameters as measured in testing and the values calculated from these measurements) comply with the respective verification tolerances as given in Table 1.(3)If the results referred to in points 2(a) or (b) are not achieved, the model and all models that have been listed as equivalent household washing machine models in the supplier's technical documentation shall be considered not to comply with this Delegated Regulation.(4)If the result referred to in point 2(c) is not achieved, the Member State authorities shall select three additional units of the same model for testing. As an alternative, the three additional units selected may be of one or more different models that have been listed as equivalent models in the supplier's technical documentation.(5)The model shall be considered to comply with the applicable requirements if for these three units, the arithmetical mean of the determined values complies with the respective tolerances given in Table 1.(6)If the result referred to in point 5 is not achieved, the model and all models that have been listed as equivalent household washing machine models in the supplier's technical documentation shall be considered not to comply with this Delegated Regulation.(7)The Member State authorities shall provide all relevant information to the authorities of the other Member States and to the Commission without delay after a decision being taken on the non-compliance of the model according to points 3 and 6.Member States' authorities shall use measurement procedures which take into account the generally recognised, state-of-the-art, reliable, accurate and reproducible measurement methods, including methods set out in documents whose reference numbers have been published for that purpose in the Official Journal of the European Union. The Member State authorities shall use the measurement and calculation methods set out in Annex VII.The Member State authorities shall only apply the verification tolerances that are set out in Table 1 and shall only use the procedure described in points 1 to 7 for the requirements referred to in this Annex. No other tolerances, such as those set out in harmonised standards or in any other measurement method, shall be applied.

Table 1Verification tolerances

Parameters	Verification tolerances
Annual energy consumption (AEC)	The determined value shall not exceed the declared value of AEC by more than 10 %.
Energy consumption (Et)	The determined value shall not exceed the declared value of Et by more than 10 %. Where three additional units need to be selected, the arithmetic mean of the determined values of these three units shall not exceed the declared value of Et by more than 6 %.
Programme time (Tt)	The determined value shall not exceed the declared values Tt by more than 10 %.
Water consumption (Wt)	The determined value shall not exceed the declared value of Wt by more than 10 %.
Remaining moisture content (D)	The determined value shall not exceed the declared value of D by more than 10 %.
Spin speed	The determined value shall not be less than the declared value by more than 10 %.
Power consumption in off mode and left-on mode (Po and Pl)	Determined values of power consumption Po and Pl of more than 1,00 W shall not exceed the declared values of Po and Pl by more than 10 %. The determined values of power consumption Po and Pl of less than or equal to 1,00 W shall not exceed the declared values of Po and Pl by more than 0,10 W.
Duration of the left-on mode (Tl)	The determined value shall not exceed the declared value of Tl by more than 10 %.
Airborne acoustical noise emissions	The determined value shall meet the declared value.

ANNEX VIEnergy efficiency classes and spin-drying efficiency classes1.ENERGY EFFICIENCY CLASSESThe energy efficiency class of a household washing machine shall be determined on the basis of its Energy Efficiency Index (EEI) as set out in Table 1.The Energy Efficiency Index (EEI) of a household washing machine shall be determined in accordance with point 1 of Annex VII.

Table 1Energy efficiency classes

Energy efficiency class	Energy Efficiency Index
A+++ (most efficient)	EEI < 46
A++	46 ≤ EEI < 52
A+	52 ≤ EEI < 59
A	59 ≤ EEI < 68
B	68 ≤ EEI < 77
C	77 ≤ EEI < 87
D (least efficient)	EEI ≥ 87

2.SPIN-DRYING EFFICIENCY CLASSESThe spin-drying efficiency class of a household washing machine shall be determined on the basis of the remaining moisture content (D) as set out in Table 2.The remaining moisture content (D) of a household washing machine shall be determined in accordance with point 3 of Annex VII.

Table 2Spin-drying efficiency classes

Spin-drying efficiency class	Remaining moisture content ( %)
A (most efficient)	D < 45
B	45 ≤ D < 54
C	54 ≤ D < 63
D	63 ≤ D < 72
E	72 ≤ D < 81
F	81 ≤ D < 90
G (least efficient)	D ≥ 90

ANNEX VIIMethod for calculating the Energy Efficiency Index, annual water consumption and remaining moisture content1.CALCULATION OF THE ENERGY EFFICIENCY INDEXFor the calculation of the Energy Efficiency Index (EEI) of a household washing machine model, the weighted annual energy consumption of a household washing machine for the standard 60 °C cotton programme at full and partial load and for the standard 40 °C cotton programme at partial load is compared to its standard annual energy consumption.(a)The Energy Efficiency Index (EEI) is calculated as follows and rounded to one decimal place:where:AECannual energy consumption of the household washing machine;SAECstandard annual energy consumption of the household washing machine.(b)The standard annual energy consumption (SAEC) is calculated in kWh/year as follows and rounded to two decimal places:SAEC = 47,0 × c + 51,7where:crated capacity of the household washing machine for the standard 60 °C cotton programme at full load or the standard 40 °C cotton programme at full load, whichever is the lower.(c)The weighted annual energy consumption (AEc) is calculated in kWh/year as follows and is rounded to two decimal places:(i)where:Etweighted energy consumption;Poweighted power in "off-mode";Plweighted power in the "left-on mode";Ttweighted programme time;220total number of standard washing cycles per year.(ii)Where the household washing machine is equipped with a power management system, with the household washing machine reverting automatically to "off-mode" after the end of the programme, the weighted annual energy consumption (AEC) is calculated taking into consideration the effective duration of "left-on mode", according to the following formula:where:Tltime in "left-on mode".(d)The weighted energy consumption (Et) is calculated in kWh as follows and rounded to three decimal places:Et = [3 × Et,60 + 2 × Et,60½ + 2 × Et,40½]/7where:Et,60energy consumption of the standard 60 °C cotton programme at full load;Et,60½energy consumption of the standard 60 °C cotton programme at partial load;Et,40½energy consumption of the standard 40 °C cotton programme at partial load.(e)The weighted power in "off-mode" (Po) is calculated in W as follows and rounded to two decimal places:Po = (3 × Po,60 + 2 × Po,60½ + 2 × Po,40½)/7where:Po,60power in "off-mode" of the standard 60 °C cotton programme at full load;Po,60½power in "off-mode" of the standard 60 °C cotton programme at partial load;Po,40½power in "off-mode" of the standard 40 °C cotton programme at partial load.(f)The weighted power in the "left-on mode" (Pl) is calculated in W as follows and rounded to two decimal places:Pl = (3 × Pl,60 + 2 × Pl,60½ + 2 × Pl,40½)/7where:Pl,60power in "left-on mode" of the standard 60 °C cotton programme at full load;Pl,60½power in "left-on mode" of the standard 60 °C cotton programme at partial load;Pl,40½power in "left-on mode" of the standard 40 °C cotton programme at partial load.(g)The weighted programme time (Tt) is calculated in minutes as follows and rounded to the nearest minute:Tt = (3 × Tt,60 + 2 × Tt,60½ + 2 × Tt,40½)/7where:Tt,60programme time of the standard 60 °C cotton programme at full load;Tt,60½programme time of the standard 60 °C cotton programme at partial load;Tt,40½programme time of the standard 40 °C cotton programme at partial load.(h)The weighted time in "left-on mode" (Tl) is calculated in minutes as follows and rounded to the nearest minute:Tl = (3 × Tl,60 + 2 × Tl,60½ + 2 × Tl,40½)/7where:Tl,60time in "left-on mode" of the standard 60 °C cotton programme at full load;Tl,60½time in "left-on mode" of the standard 60 °C cotton programme at partial load;Tl,40½time in "left-on mode" of the standard 40 °C cotton programme at partial load.2.CALCULATION OF THE WEIGHTED ANNUAL WATER CONSUMPTION(a)The weighted annual water consumption (AWC) of a household washing machine is calculated in litres as follows and rounded up to the integer:AWc = Wt × 220where:Wtweighted water consumption;220total number of standard washing cycles per year.(b)The weighted water consumption (Wt) is calculated in litres as follows and rounded up to the integerWt = (3 × Wt,60 + 2 × Wt,60½ + 2 × Wt,40½)/7where:Wt,60water consumption of the standard 60 °C cotton programme at full load;Wt,60½water consumption of the standard 60 °C cotton programme at partial load;Wt,40½water consumption of the standard 40 °C cotton programme at partial load.3.CALCULATION OF THE WEIGHTED REMAINING MOISTURE CONTENTThe weighted remaining moisture content (D) of a household washing machine is calculated in percentage as follows and rounded to the nearest whole percent:D = (3 × D60 + 2 × D60½ + 2 × D40½)/7where:D60is the residual moisture content for the standard 60 °C cotton programme at full load, in percentage and rounded to the nearest whole per cent;D60½is the residual moisture content for the standard 60 °C cotton programme at partial load, in percentage and rounded to the nearest whole per cent;D40½is the residual moisture content for the standard 40 °C cotton programme at partial load, in percentage and rounded to the nearest whole per cent.ANNEX VIIIInformation to be provided in the case of sale, hire or hire-purchase through the internet(1)For the purpose of points 2 to 5 of this Annex the following definitions shall apply:(a)"display mechanism" means any screen, including tactile screen, or other visual technology used for displaying internet content to users;(b)"nested display" means visual interface where an image or data set is accessed by a mouse click, mouse roll-over or tactile screen expansion of another image or data set;(c)"tactile screen" means a screen responding to touch, such as that of a tablet computer, slate computer or a smartphone;(d)"alternative text"D means text provided as an alternative to a graphic allowing information to be presented in non-graphical form where display devices cannot render the graphic or as an aid to accessibility such as input to voice synthesis applications.(2)The appropriate label made available by suppliers in accordance with Article 3(f) shall be shown on the display mechanism in proximity to the price of the product. The size shall be such that the label is clearly visible and legible and shall be proportionate to the size specified in point 2 of Annex I. The label may be displayed using a nested display, in which case the image used for accessing the label shall comply with the specifications laid down in point 3 of this Annex. If nested display is applied, the label shall appear on the first mouse click, mouse roll-over or tactile screen expansion on the image.(3)The image used for accessing the label in the case of nested display shall:(a)be an arrow in the colour corresponding to the energy efficiency class of the product on the label;(b)indicate on the arrow the energy efficiency class of the product in white in a font size equivalent to that of the price; and(c)have one of the following two formats:(4)In the case of nested display, the sequence of display of the label shall be as follows:(a)the image referred to in point 3 of this Annex shall be shown on the display mechanism in proximity to the price of the product;(b)the image shall link to the label;(c)the label shall be displayed after a mouse click, mouse roll-over or tactile screen expansion on the image;(d)the label shall be displayed by pop up, new tab, new page or inset screen display;(e)for magnification of the label on tactile screens, the device conventions for tactile magnification shall apply;(f)the label shall cease to be displayed by means of a close option or other standard closing mechanism;(g)the alternative text for the graphic, to be displayed on failure to display the label, shall be the energy efficiency class of the product in a font size equivalent to that of the price.(5)The appropriate product fiche made available by suppliers in accordance with Article 3(g) shall be shown on the display mechanism in proximity to the price of the product. The size shall be such that the product fiche is clearly visible and legible. The product fiche may be displayed using a nested display, in which case the link used for accessing the fiche shall clearly and legibly indicate "Product fiche". If nested display is used, the product fiche shall appear on the first mouse click, mouse roll-over or tactile screen expansion on the link.

Article 8RepealDirective 95/12/EC shall be repealed from 20 December 2011.

Table 1Verification tolerances

Parameters	Verification tolerances
Annual energy consumption (AEC)	The determined value shall not exceed the declared value of AEC by more than 10 %.
Energy consumption (Et)	The determined value shall not exceed the declared value of Et by more than 10 %. Where three additional units need to be selected, the arithmetic mean of the determined values of these three units shall not exceed the declared value of Et by more than 6 %.
Programme time (Tt)	The determined value shall not exceed the declared values Tt by more than 10 %.
Water consumption (Wt)	The determined value shall not exceed the declared value of Wt by more than 10 %.
Remaining moisture content (D)	The determined value shall not exceed the declared value of D by more than 10 %.
Spin speed	The determined value shall not be less than the declared value by more than 10 %.
Power consumption in off mode and left-on mode (Po and Pl)	Determined values of power consumption Po and Pl of more than 1,00 W shall not exceed the declared values of Po and Pl by more than 10 %. The determined values of power consumption Po and Pl of less than or equal to 1,00 W shall not exceed the declared values of Po and Pl by more than 0,10 W.
Duration of the left-on mode (Tl)	The determined value shall not exceed the declared value of Tl by more than 10 %.
Airborne acoustical noise emissions	The determined value shall meet the declared value.

Table 1Energy efficiency classes

Energy efficiency class	Energy Efficiency Index
A+++ (most efficient)	EEI < 46
A++	46 ≤ EEI < 52
A+	52 ≤ EEI < 59
A	59 ≤ EEI < 68
B	68 ≤ EEI < 77
C	77 ≤ EEI < 87
D (least efficient)	EEI ≥ 87

Table 2Spin-drying efficiency classes

Spin-drying efficiency class	Remaining moisture content ( %)
A (most efficient)	D < 45
B	45 ≤ D < 54
C	54 ≤ D < 63
D	63 ≤ D < 72
E	72 ≤ D < 81
F	81 ≤ D < 90
G (least efficient)	D ≥ 90

Commission Delegated Regulation (EU) No 1061/2010 of 28 September 2010 supplementing Directive 2010/30/EU of the European Parliament and of the Council with regard to energy labelling of household washing machines Text with EEA relevance