Directive 2009/105/EC of the European Parliament and of the Council of 16 September 2009 relating to simple pressure vessels (Codified version) (Text with EEA relevance)
Modified by
Regulation (EU) No 1025/2012 of the European Parliament and of the Councilof 25 October 2012on European standardisation, amending Council Directives 89/686/EEC and 93/15/EEC and Directives 94/9/EC, 94/25/EC, 95/16/EC, 97/23/EC, 98/34/EC, 2004/22/EC, 2007/23/EC, 2009/23/EC and 2009/105/EC of the European Parliament and of the Council and repealing Council Decision 87/95/EEC and Decision No 1673/2006/EC of the European Parliament and of the Council(Text with EEA relevance), 32012R1025, November 14, 2012
Directive 2009/105/EC of the European Parliament and of the Councilof 16 September 2009relating to simple pressure vessels(codified version)(Text with EEA relevance)THE EUROPEAN PARLIAMENT AND THE COUNCIL OF THE EUROPEAN UNION,Having regard to the Treaty establishing the European Community, and in particular Article 95 thereof,Having regard to the proposal from the Commission,Having regard to the opinion of the European Economic and Social CommitteeOJ C 27, 3.2.2009, p. 41.,Acting in accordance with the procedure laid down in Article 251 of the TreatyOpinion of the European Parliament of 21 October 2008 (not yet published in the Official Journal) and Council Decision of 13 July 2009.,Whereas:(1)Council Directive 87/404/EEC of 25 June 1987 on the harmonization of the laws of the Member States relating to simple pressure vesselsOJ L 220, 8.8.1987, p. 48. has been substantially amended several timesSee Annex IV, Part A.. In the interests of clarity and rationality the said Directive should be codified.(2)Member States have the responsibility of ensuring the safety on their territory of persons, domestic animals and property with regard to the hazards resulting from the leakage or bursting of simple pressure vessels.(3)In each Member State, mandatory provisions define in particular the safety level required of simple pressure vessels by specifying design and operating characteristics, conditions of installation and use and inspection procedures before and after the placing on the market. These mandatory provisions do not necessarily lead to different safety levels from one Member State to another but do, by their disparity, hinder trade within the Community.(4)This Directive should therefore contain only mandatory and essential requirements. To facilitate proof of conformity with the essential requirements, it is necessary to have harmonised standards at Community level, in particular as to the design, operation and installation of simple pressure vessels, so that products complying with them may be assumed to conform to the safety requirements. These standards harmonised at Community level are drawn up by private bodies and should remain non-mandatory texts. For that purpose, the European Committee for Standardisation (CEN), the European Committee for Electrotechnical Standardisation (Cenelec) and the European Telecommunications Standards Institute (ETSI) are recognised as the competent bodies for the adoption of harmonised standards in accordance with the general guidelinesOJ C 91, 16.4.2003, p. 7. for cooperation between the Commission, the European Free Trade Association (EFTA) and those three bodies signed on 28 March 2003.(5)The Council has already adopted a series of Directives designed to remove technical barriers to trade in accordance with the principles established in its Resolution of 7 May 1985 on a new approach to technical harmonisation and standardsOJ C 136, 4.6.1985, p. 1.; each of those Directives provides for the affixing of the "CE" marking. The Commission, in its Communication of 15 June 1989 on a global approach to certification and testingOJ C 267, 19.10.1989, p. 3., proposed that common rules be drawn up concerning a "CE" marking with a single design. The Council, in its Resolution of 21 December 1989 on a global approach to conformity assessmentOJ C 10, 16.1.1990, p. 1., approved as a guiding principle the adoption of a consistent approach such as this with regard to the use of the "CE" marking. The two basic elements of the new approach which should be applied are the essential requirements and the conformity assessment procedures.(6)A check on compliance with the relevant technical requirements is necessary in order to provide effective protection for users and third parties. The existing inspection procedures differ from one Member State to another. In order to avoid multiple inspections, which are in effect barriers to the free movement of vessels, arrangements should be made for the mutual recognition of inspection procedures by the Member States. In order to facilitate the mutual recognition of inspection procedures, Community procedures should be established as well as the criteria for appointing the bodies responsible for carrying out tests, surveillance and verification.(7)The presence on a simple pressure vessel of the "CE" marking should raise a presumption that it satisfies the provisions of this Directive and should therefore make it unnecessary, upon the importation and putting into service of the vessel, to repeat the inspections already carried out. Nevertheless simple pressure vessels might represent a safety hazard. Provision should therefore be made for a procedure to reduce this hazard.(8)This Directive should be without prejudice to the obligations of the Member States relating to the time limits for transposition into national law and application of the Directives set out in Annex IV, Part B,HAVE ADOPTED THIS DIRECTIVE: