Commission Regulation (EEC) No 911/79 of 7 May 1979 re-establishing the levying of customs duties on angles, shapes and sections, of iron or steel, etc., falling within subheadings 73.11 A II, III, IV a) 2 and b) and originating in Romania, to which the preferential tariff arrangements set out in Council Regulation (EEC) No 3156/78 apply

++++

COMMISSION REGULATION ( EEC ) NO 911/79

OF 7 MAY 1979

RE-ESTABLISHING THE LEVYING OF CUSTOMS DUTIES ON ANGLES , SHAPES AND SECTIONS , OF IRON OR STEEL , ETC . , FALLING WITHIN SUBHEADINGS 73.11 A II , III , IV A ) 2 AND B ) AND ORIGINATING IN ROMANIA , TO WHICH THE PREFERENTIAL TARIFF ARRANGEMENTS SET OUT IN COUNCIL REGULATION ( EEC ) NO 3156/78 APPLY

THE COMMISSION OF THE EUROPEAN COMMUNITIES ,

HAVING REGARD TO THE TREATY ESTABLISHING THE EUROPEAN ECONOMIC COMMUNITY ,

HAVING REGARD TO COUNCIL REGULATION ( EEC ) NO 3156/78 OF 29 DECEMBER 1978 ESTABLISHING PREFERENTIAL TARIFFS IN RESPECT OF CERTAIN PRODUCTS ORIGINATING IN DEVELOPING COUNTRIES ( 1 ) , AND IN PARTICULAR ARTICLE 4 ( 2 ) THEREOF ,

WHEREAS ARTICLE 1 ( 3 ) AND ( 4 ) OF THAT REGULATION PROVIDES THAT CUSTOMS DUTIES MAY , FOR EACH CATEGORY OF PRODUCTS , BE SUSPENDED UP TO A COMMUNITY CEILING , EXPRESSED IN EUROPEAN UNITS OF ACCOUNT , WHICH WILL BE EQUAL - WITH THE EXCEPTION OF CERTAIN PRODUCTS THE VALUE OF THE CEILINGS FOR WHICH IS GIVEN IN ANNEX A THERETO - TO THE SUM ARRIVED AT BY ADDING TOGETHER THE VALUE OF THE PRODUCTS IN QUESTION IMPORTED CIF INTO THE COMMUNITY IN 1974 AND COMING FROM COUNTRIES AND TERRITORIES COVERED BY THOSE ARRANGEMENTS , BUT NOT INCLUDING PRODUCTS COMING FROM COUNTRIES AND TERRITORIES ALREADY COVERED BY VARIOUS PREFERENTIAL TARIFF ARRANGEMENTS ESTABLISHED BY THE COMMUNITY , AND 5 % OF THE VALUE OF 1976 CIF IMPORTS COMING FROM OTHER COUNTRIES AND FROM COUNTRIES AND TERRITORIES ALREADY COVERED BY SUCH ARRANGEMENTS ; WHEREAS , HOWEVER , THE CEILING RESULTING FROM THE SUM OF THIS ADDITION MAY IN NO CASE EXCEED 150 % OF THE PREFERENTIAL CEILING OPENED FOR 1978 ;

WHEREAS , HAVING REGARD TO THAT CEILING , THE AMOUNTS FOR PRODUCTS ORIGINATING IN ANY ONE OF THE COUNTRIES OR TERRITORIES LISTED IN ANNEX B TO THAT REGULATION SHOULD BE WITHIN A MAXIMUM COMMUNITY AMOUNT REPRESENTING 50 % OF THAT CEILING , WITH THE EXCEPTION OF CERTAIN PRODUCTS FOR WHICH THE MAXIMUM AMOUNT IS TO BE REDUCED TO THE PERCENTAGE INDICATED IN ANNEX A THERETO ;

WHEREAS ARTICLE 2 ( 2 ) AND ( 3 ) OF THAT REGULATION PROVIDES THAT THE LEVYING OF CUSTOMS DUTIES MAY BE RE-ESTABLISHED AT ANY TIME IN RESPECT OF IMPORTS OF THE PRODUCTS IN QUESTION ORIGINATING IN ANY OF THE SAID COUNTRIES OR TERRITORIES - WITH THE EXCEPTION OF THOSE LISTED IN ANNEX C THERETO - ONCE THE RELEVANT COMMUNITY AMOUNT HAS BEEN REACHED ;

WHEREAS , IN RESPECT OF ANGLES , SHAPES AND SECTIONS , OF IRON OR STEEL , ETC . , FALLING WITHIN SUBHEADINGS 73.11 A II , III , IV A ) 2 AND B ) , THE CEILING , CALCULATED AS INDICATED ABOVE , SHOULD BE 543 000 EUROPEAN UNITS OF ACCOUNT , AND THEREFORE THE MAXIMUM AMOUNT IS 271 000 EUROPEAN UNITS OF ACCOUNT ; WHEREAS , ON 23 APRIL 1979 , THE AMOUNTS OF IMPORTS INTO THE COMMUNITY OF ANGLES , SHAPES AND SECTIONS , OF IRON OR STEEL , ETC . , FALLING WITHIN SUBHEADINGS 73.11 A II , III , IV A ) 2 AND B ) AND ORIGINATING IN ROMANIA , A COUNTRY COVERED BY PREFERENTIAL TARIFF ARRANGEMENTS , REACHED THAT MAXIMUM AMOUNT ; WHEREAS , BEARING IN MIND THE OBJECTIVES OF REGULATION ( EEC ) NO 3156/78 WHICH PROVIDES THAT MAXIMUM AMOUNTS SHOULD NOT BE EXCEEDED , CUSTOMS DUTIES SHOULD BE RE-ESTABLISHED IN RESPECT OF THE PRODUCTS IN QUESTION IN RELATION TO ROMANIA ,

HAS ADOPTED THIS REGULATION :

ARTICLE 1

AS FROM 12 MAY 1979 , THE LEVYING OF CUSTOMS DUTIES , SUSPENDED IN PURSUANCE OF COUNCIL REGULATION ( EEC ) NO 3156/78 , SHALL BE RE-ESTABLISHED IN RESPECT OF THE FOLLOWING PRODUCTS , IMPORTED INTO THE COMMUNITY AND ORIGINATING IN ROMANIA :

CCT HEADING NO*DESCRIPTION*

73.11*ANGLES , SHAPES AND SECTIONS , OF IRON OR STEEL , HOT-ROLLED , FORGED , EXTRUDED , COLD-FORMED OR COLD-FINISHED ; SHEET PILING OF IRON OR STEEL , WHETHER OR NOT DRILLED , PUNCHED OR MADE FROM ASSEMBLED ELEMENTS : *

*A . ANGLES , SHAPES AND SECTIONS : *

*II . NOT FURTHER WORKED THAN FORGED*

*III . NOT FURTHER WORKED THAN COLD-FORMED OR COLD-FINISHED*

*IV . CLAD OR SURFACE-WORKED ( FOR EXAMPLE , POLISHED , COATED ) : *

*A ) NOT FURTHER WORKED THAN CLAD : *

*2 . COLD-FORMED OR COLD-FINISHED*

*B ) OTHER*

ARTICLE 2

THIS REGULATION SHALL ENTER INTO FORCE ON THE THIRD DAY FOLLOWING ITS PUBLICATION IN THE OFFICIAL JOURNAL OF THE EUROPEAN COMMUNITIES .

THIS REGULATION SHALL BE BINDING IN ITS ENTIRETY AND DIRECTLY APPLICABLE IN ALL MEMBER STATES .

DONE AT BRUSSELS , 7 MAY 1979 .

FOR THE COMMISSION

ETIENNE DAVIGNON

MEMBER OF THE COMMISSION

( 1 ) OJ NO L 375 , 30 . 12 . 1978 , P . 26 .