Regulation (EU) 2024/3110 of the European Parliament and of the Council of 27 November 2024 laying down harmonised rules for the marketing of construction products and repealing Regulation (EU) No 305/2011 (Text with EEA relevance)
Regulation (EU) 2024/3110 of the European Parliament and of the Councilof 27 November 2024laying down harmonised rules for the marketing of construction products and repealing Regulation (EU) No 305/2011(Text with EEA relevance) THE EUROPEAN PARLIAMENT AND THE COUNCIL OF THE EUROPEAN UNION,Having regard to the Treaty on the Functioning of the European Union, and in particular Article 114 thereof,Having regard to the proposal from the European Commission,After transmission of the draft legislative act to the national parliaments,Having regard to the opinion of the European Economic and Social CommitteeOJ C 75, 28.2.2023, p. 159.,Acting in accordance with the ordinary legislative procedurePosition of the European Parliament of 10 April 2024 (not yet published in the Official Journal) and decision of the Council of 5 November 2024.,Whereas:(1)Regulation (EU) No 305/2011 of the European Parliament and of the CouncilRegulation (EU) No 305/2011 of the European Parliament and of the Council of 9 March 2011 laying down harmonised conditions for the marketing of construction products and repealing Council Directive 89/106/EEC (OJ L 88, 4.4.2011, p. 5). was adopted in the context of the internal market, in order to harmonise conditions for the marketing of construction products and to remove obstacles to trade in construction products between Member States.(2)Under Regulation (EU) No 305/2011, in order for a construction product covered by a harmonised technical specification to be placed on the market, the manufacturer is obliged to draw up a declaration of performance for such product. The manufacturer assumes the responsibility for the conformity of the product with such declared performance and with applicable requirements. Manufacturers are exempted from this obligation for certain products.(3)Experience with the implementation of Regulation (EU) No 305/2011, the evaluation conducted by the Commission in 2019 as well as the report on the European Organisation for Technical Assessment have shown the underperformance of the framework on construction products in various respects, including as regards the development of standards and the market surveillance. In addition, feedback received in the course of the evaluation has pointed to the need of reducing the overlaps, removing contradictions and repetitive requirements, including in relation to other Union legislation, in order to provide more legal clarity and limit the administrative burden on the economic operators. It is therefore necessary to update and align legal obligations of economic operators with those provided for in other Union legislation, as well as to add new provisions including as regards market surveillance, so that legal certainty is increased and that diverging interpretations are avoided.(4)It is necessary to establish well-functioning information flows, including via electronic means and using a machine-readable format, to ensure that coherent and transparent information about construction products performances is available along the supply chain. This is expected to increase transparency and to improve efficiency in terms of information transfer. Ensuring digital access to comprehensive information about construction products would contribute to the digitalisation of the construction sector altogether, making the framework fit for the digital age. Moreover, providing access to reliable and durable information would also mean that economic operators and other actors would not contribute to each other’s non-compliance with requirements.(5)The European Parliament resolution of 10 March 2021 on the implementation of Regulation (EU) No 305/2011 laying down harmonised conditions for the marketing of construction products (the Construction Products Regulation)OJ C 474, 24.11.2021, p. 41. welcomed the Commission’s objective to make the construction sector more sustainable by addressing the sustainability performance of construction products in the revision of Regulation (EU) No 305/2011, as announced in Commission’s communication of 11 March 2020 entitled "A new Circular Economy Action Plan. For a cleaner and more competitive Europe". The Council Conclusions on the Circular Economy in the Construction Sector of 28 November 2019 urged the Commission to facilitate the circularity of construction products when revising Regulation (EU) No 305/2011. In its Communication of 10 March 2020 entitled "A New Industrial Strategy for Europe" the Commission emphasised the need to address the sustainability of construction products and highlighted a more sustainable built environment as essential for Europe’s transition towards climate-neutrality. In its Communication of 5 May 2021 entitled "Updating the 2020 New Industrial Strategy: Building a stronger Single Market for Europe’s recovery" the Commission identified construction as one of the priority ecosystems that face the most important challenges meeting climate and sustainability goals and embracing the digital transformation, and on which the competitiveness of the construction sector depends. It is therefore appropriate to lay down rules for declaring environmental sustainability performance of construction products, including the possibility of establishing relevant threshold levels and classes. Classes of performance for the environmental performance of products should accurately reflect the diversity of products and their state of the art and should allow for the most environmentally friendly products to be accurately identified. Moreover, when referring to environmental impacts, such classes of performance should be understandable, should not be misleading, nor allow for burden shifting.(6)Similarly, the 2022 EU Strategy on Standardisation set out in the Commission Communication of 2 February 2022, entitled "An EU Strategy on Standardisation – Setting global standards in support of a resilient, green and digital EU single market" identified construction as one of the most pertinent areas where harmonised standards could improve competitiveness and reduce market barriers.(7)Pursuing the environmental goals, including the fight against climate change and the transition towards a circular economy, makes it necessary to establish, without increasing disproportionately bureaucracy and costs for economic operators, especially for small and medium-sized enterprises ("SMEs"), new environmental obligations and to lay the ground for the development and the application of an assessment method for the calculation of the environmental sustainability of construction products. The calculations should cover the life cycle of the product using the methods established through standardisation. For new products the calculated life cycles should include all stages of a product’s life, from raw material acquisition or generation from natural resources, to its final disposal, including potential benefits and loads outside the boundary limits. For used and remanufactured products, the calculated life cycle should start with the deinstallation from a construction work and should include all following stages until final disposal. The Commission should make available software to perform the calculation, in particular the characterisation factors applicable in accordance with European standard EN 15804 or future applicable standards. Any update of this software should be communicated and should trigger the update to the relevant calculations within one year.(8)To ensure safety and functionality of construction products and, by extension, of construction works as well as safety of workers and users, it is necessary to ensure that certain service providers, such as fulfilment service providers, online marketplaces and actors providing intermediary services, do not contribute to the non-compliance of other actors. It is therefore necessary to render relevant provisions applicable also to these services and their providers.(9)To create the necessary link between construction products and the construction works, including buildings, into which they might be incorporated, the notion of construction works should be defined only for the purposes of this Regulation and without prejudice to Member States’ competences to define and regulate construction works and buildings.(10)In order to avoid innovative distribution models being used to circumvent the obligations under this Regulation, it should be clarified that any supply of a product in the course of a commercial activity, including when ownership or possession of the products is transferred as part of the provision of a service, would be considered as the product being made available on the market.(11)Ensuring the free movement of kits for construction products on the internal market would support industry competitiveness. This approach would expand market reach, streamline production processes for companies, and improve convenience for both consumers and businesses.(12)The compliance of construction products with Union legislation often depends on the compliance of their key parts with that legislation. However, since key parts are often integrated into various construction products, ensuring safety and the protection of the environment, including climate, would be better achieved if those key parts were assessed upstream, that is if their performance and conformity were assessed beforehand and independently from the assessment of the final construction product into which they are integrated. Similarly, market surveillance would be more efficient if non-compliant key parts could be identified and targeted. Therefore, it is necessary to lay down mandatory rules applicable to key parts of construction products. The same approach should be used for parts or materials intended to be used for construction products which would benefit from the voluntary application of the Regulation.(13)Items, such as construction products, their key parts or other parts or materials, can be placed on the market as such or as a set of separate components intended to be used together and should be subject to dedicated harmonised technical specifications. To simplify the application of this Regulation, the items and components falling under its scope should be clearly identified. However, such identification should not preclude the possibility to market the components as construction products when these components are placed on the market separately, as key parts or otherwise.(14)While keeping a broad scope for the possible application of this Regulation, its application to certain products already harmonised by other Union legal acts should be excluded to avoid regulatory overlap. For the same purpose, it is also important to distinguish between those aspects of the same products which are covered by this Regulation and those aspects which are regulated by other sectorial legislation. This would be the case, for example, for lighting products and electrical and electronic products, which are subject to Directives 2014/35/EUDirective 2014/35/EU of the European Parliament and of the Council of 26 February 2014 on the harmonisation of the laws of the Member States relating to the making available on the market of electrical equipment designed for use within certain voltage limits (OJ L 96, 29.3.2014, p. 357)., 2014/30/EUDirective 2014/30/EU of the European Parliament and of the Council of 26 February 2014 on the harmonisation of the laws of the Member States relating to electromagnetic compatibility (OJ L 96, 29.3.2014, p. 79)., 2014/53/EUDirective 2014/53/EU of the European Parliament and of the Council of 16 April 2014 on the harmonisation of the laws of the Member States relating to the making available on the market of radio equipment and repealing Directive 1999/5/EC (OJ L 153, 22.5.2014, p. 62). and 2001/95/ECDirective 2001/95/EC of the European Parliament and of the Council of 3 December 2001 on general product safety (OJ L 11, 15.1.2002, p. 4). of the European Parliament and of the Council. The broad scope of this Regulation should however not be interpreted as an intention to harmonise all products which can be placed on the market for incorporation into construction works. Products which are not suitable for harmonisation, for instance due to their relation to cultural heritage, their usage of specific materials which can only be sourced in certain localities or to heterogeneous conditions between Member States, should not be subject to the harmonising effect of this Regulation. This could be achieved through the active choice of not pursuing their coverage through harmonised technical specifications.(15)Used products subject to this Regulation imported from third countries, should, in the absence of dedicated rules for used products, be subject to the same rules as new construction products.(16)Construction products placed on the market in the outermost regions of the Union are often imported from neighbouring countries, and are therefore not subject to requirements laid down in Union law. Subjecting those construction products to such requirements would be disproportionately costly. At the same time, construction products manufactured in the outermost regions hardly circulate in other Member States. Therefore, Member States should have the possibility to exempt construction products placed on the market in the outermost regions of the Union from those requirements.(17)To ensure that a strong link between standards and the regulatory needs of the Member States is maintained, an expert group should support the Commission in the preparation of standardisation requests and other harmonised technical specifications. The work of the expert group should follow a working plan established on the basis of inputs from Member States in addition to overall Union priorities such as EU climate and circular economy goals. In establishing the priorities of the working plan, the Commission should pay particular attention to the replacement of harmonised technical specifications adopted under Regulation (EU) No 305/2011. The Commission should inform the Member States and the European Parliament on a yearly basis about progress in implementing the working plan, including information on the standardisation requests issued, the number of standards proposed by the European standardisation organisations, the average time needed for the assessment of standards by the Commission, and the ratio between standards accepted and rejected by the Commission.(18)In accordance with the principle of proportionality, it is necessary and appropriate for the achievement of the basic objective of harmonising the internal market for construction products to address the regulatory needs of Member States by defining only the necessary essential characteristics to assess the product performance. The definition of these essential characteristics and the assessment methods applicable to them should provide the less onerous approach with sufficient reliability and avoid duplications and inconsistencies. This Regulation does not go beyond what is necessary in order to achieve this objective, in accordance with Article 5(4) of the Treaty on European Union (TEU).(19)In order to strive for a maximum of regulatory coherence, this Regulation should to the extent possible build on the horizontal legal framework, in this case namely on Regulation (EU) No 1025/2012 of the European Parliament and of the CouncilRegulation (EU) No 1025/2012 of the European Parliament and of the Council of 25 October 2012 on European standardisation, amending Council Directives 89/686/EEC and 93/15/EEC and Directives 94/9/EC, 94/25/EC, 95/16/EC, 97/23/EC, 98/34/EC, 2004/22/EC, 2007/23/EC, 2009/23/EC and 2009/105/EC of the European Parliament and of the Council and repealing Council Decision 87/95/EEC and Decision No 1673/2006/EC of the European Parliament and of the Council (OJ L 316, 14.11.2012, p. 12).. It follows the recent trend in product legislation to develop a fall-back solution where the European standardisation organisations do not deliver valid harmonised standards. When a European standardisation organisation delivers a harmonised standard in accordance with the standardisation request which includes elements that do not satisfy the regulatory needs of Member States, or are not aligned with the Union safety, environmental, circularity and climate objectives, the Commission should revise the standardisation request or make the harmonised standard mandatory with restrictions. A fall-back solution should be possible to apply to harmonised standards which are not compliant with the standardisation request and address a product family or product category which is either not previously covered by a harmonised standard, or is already covered by a harmonised standard applicable for more than 5 years, or is covered by a harmonised standard applicable with restrictions.(20)Where harmonised standards lay down the rules for the assessment of performance with regard to essential characteristics relevant for the construction codes of Member States, those standards should be made mandatory for the purposes of application of this Regulation as performance harmonised standards, as only such mandatory standards reach the goal of permitting the free circulation of products, whilst ensuring the Member States’ ability to request product characteristics related to the basic requirements for construction works in view of their specific national situation such as differences in climate, geology and geography and other conditions. When pursued together, these two goals require that products are assessed by a single assessment method, therefore the method needs to be mandatory. However, voluntary standards can be used to make product requirements, specified for the relevant product family or product category by delegated acts, even more concrete, following the path of Decision No 768/2008/EC of the European Parliament and of the CouncilDecision No 768/2008/EC of the European Parliament and of the Council of 9 July 2008 on a common framework for the marketing of products, and repealing Council Decision 93/465/EEC (OJ L 218, 13.8.2008, p. 82).. In line with Decision No 768/2008/EC, those voluntary standards should be able to provide a presumption of conformity with the requirements covered by them.(21)The assessment of performance with regard to essential characteristics may require the establishment of threshold levels. Voluntary threshold levels have to be fulfilled in relation to certain applications. Mandatory threshold levels have to be fulfilled as a condition for placing the product on the internal market irrespective of its application.(22)In order to contribute to the objectives of the European Green Deal set out in Commission’s communication of 11 December 2019 entitled "The European Green Deal", the Circular Economy Action Plan and the Zero Pollution Action Plan set out in Commission’s communication of 12 May 2021 entitled "Pathway to a Healthy Planet for All. EU Action Plan: "Towards Zero Pollution for Air, Water and Soil"", and to ensure safe construction products, safety being one of the goals to be pursued in the legislation based on Article 114 of the Treaty on the Functioning of the European Union (TFEU), product requirements related to functionality, safety, and protection of environment, including climate, are necessary. When setting these requirements, the Commission should address the safety risks and take into account the product’s potential contribution to achieving Union climate, environmental and energy efficiency objectives over the course of their life cycle. Those requirements do not relate to the performance of construction products. Contrary to its predecessor Council Directive 89/106/EECCouncil Directive 89/106/EEC of 21 December 1988 on the approximation of laws, regulations and administrative provisions of the Member States relating to construction products (OJ L 40, 11.2.1989, p. 12)., Regulation (EU) No 305/2011 does not provide for the possibility to establish such product requirements. However, certain harmonised standards for construction products contain such product requirements. Those standards demonstrate that there is a practical need for such requirements on functionality, safety, and protection of environment. Article 114 TFEU as the legal basis of this Regulation also imposes the pursuit of a high level of health, safety and protection of the environment. Thus, this Regulation should reintroduce or validate product requirements. Hence, the power to adopt acts in accordance with Article 290 TFEU should be delegated to the Commission to specify those requirements for the respective product family or product category.(23)Manufacturing and distribution of construction products becomes ever more complex, leading to the emergence of new specialised operators, such as fulfilment service providers. For reasons of clarity, certain generic obligations, including on cooperation with authorities, should be applicable to all those involved in the supply chain.(24)In order to foster harmonised practices amongst Member States even where a consensus about these practices could not be found, the Commission should be empowered to adopt, with regard to a limited range of issues, implementing acts on the implementation of this Regulation. The respective empowerments should concern the obligations and rights of economic operators and the obligations of notified bodies.(25)In order to improve the legal certainty and to mitigate the fragmentation of the Union market for construction products it is necessary to clearly define the area regulated at Union level, the so-called "harmonised zone", as opposed to the elements remaining within the competence of Member States. Member States remain competent to lay down provisions on construction works, including on their design and dimensioning. The establishment of the harmonised zone should not affect the right of Member States to specify national requirements on construction works and should not reduce the level of protection already existing and justified in the Member States. National environmental policies applicable to construction works should not be considered as prohibitions or barriers to the making available of products on the market as long as they respect the harmonised zone.(26)Member States set the safety level for construction works on the basis of their responsibilities towards their citizens, while the Union determines the framework conditions for the internal market. The competence to adopt provisions on construction works remains with the Member States. The basic requirements for construction works set out in this Regulation should establish the links to construction products that are technically necessary, and serve as a basis for issuing standardisation requests to the European standardisation organisations for the development of harmonised standards for construction products, corresponding delegated acts as well as for the development of European assessment documents.(27)The harmonised zone should also apply to public contracts, grants or other positive incentives with the exception of fiscal incentives.(28)In order to strike a balance between mitigating the fragmentation of the market and the legitimate interests of Member States to regulate construction works, it is necessary to provide for a mechanism to better reflect the needs of the Member States in the development of harmonised technical specifications. For the same reason, an additional mechanism of prior authorisation should be established, allowing Member States to set, based on imperative grounds of health and safety of persons or of protection of the environment, requirements other than those laid down in the harmonised technical specifications for products covered by the harmonised zone. This mechanism should give Member States the possibility, while awaiting updated harmonised technical specifications addressing their regulatory needs, to notify and seek authorisation for national measures affecting the performance of an essential characteristic not addressed by the harmonised technical specification. This mechanism should be complementary to a Member State’s possibility to notify the Commission, in accordance with Article 114 TFEU, when it deems it necessary to introduce national provisions based on new scientific evidence relating to the protection of the environment or the working environment on grounds of a problem specific to that Member State in contradiction with harmonised technical specifications. In order to ensure that authorised national measures only remain as temporary deviations from the harmonised zone, it is important to enable swift consultations on the need to update harmonised technical specifications in light of those regulatory needs, including, where appropriate, through standardisation requests with deadlines specifically set to address the urgency at hand.(29)A circular economy, the key element of the Circular Economy Action Plan, can be promoted by mandatory deposit-refund systems and the obligation of manufacturers to regain ownership of new, surplus or unsold non-custom made products. Member States should therefore be allowed to take such measures and to establish obligations regarding the collection and the treatment of products for waste. The owner of the product should be in charge of the transport back to the distributor, importer or manufacturer.(30)In order to enhance legal clarity and reduce the administrative burden for the economic operators, it is necessary to avoid that construction products are subject to multiple assessments regarding the same aspect of health and safety of persons or protection of the environment, including climate, under different Union legal acts. This was confirmed by the REFIT platform, established by Commission Decision C(2015) 3261, recommending that the Commission gives priority to addressing the problems of overlapping and repetitive requirements. While not reducing or encroaching on the level of protection already existing and justified in Member States at construction level, the Commission should thus be able to determine the conditions under which the fulfilment of obligations provided for in other Union legal acts also fulfils certain obligations of this Regulation, where otherwise the same aspect of health and safety of persons or protection of the environment, including climate, would be assessed in parallel under this Regulation and other Union law.(31)Moreover, in order to avoid diverging practices of Member States and economic operators, the power to adopt implementing acts in accordance with Article 291 TFEU should be granted to the Commission to determine whether certain items fall within the definition of product.(32)As this Regulation is developed in line with the framework of Regulation (EU) 2024/1781 of the European Parliament and of the CouncilRegulation (EU) 2024/1781 of the European Parliament and of the Council of 13 June 2024 establishing a framework for the setting of ecodesign requirements for sustainable products, amending Directive (EU) 2020/1828 and Regulation (EU) 2023/1542 and repealing Directive 2009/125/EC (OJ L, 2024/1781, 28.6.2024, ELI: http://data.europa.eu/eli/reg/2024/1781/oj). but with its provisions adapted to the sectorial specificities of construction products, it will be, with limited exceptions, the legal act used for harmonising all relevant aspects of construction products, including sustainability aspects even though these might also be addressed through Regulation (EU) 2024/1781. If a policy need is identified horizontally within the framework of Regulation (EU) 2024/1781, the Commission should primarily use this Regulation for addressing this need in regard to construction products. Only in exceptional cases where requirements under this Regulation are insufficient and cannot be amended or complemented in a reasonable time, it should be possible to apply Regulation (EU) 2024/1781 in a complementary manner to construction products, provided the administrative cost entailed, including as a result of economic operators potentially becoming subject to two conformity assessment procedures, is shown to be reasonable. As an exception, in the case of energy-related products included in ecodesign working plans which are also construction products and for intermediate products within the meaning of Regulation (EU) 2024/1781, with the exception of cement, priority for the setting of sustainability requirements will be given to that Regulation. This will be the case for instance for heaters, boilers, heat pumps, water and space heating appliances, fans, cooling and ventilating systems and photovoltaic products, excluding building-integrated photovoltaic panels. This Regulation would still apply in a complementary manner where needed, mainly in relation to safety aspects also taking account of other Union legislation on products such as on gas appliances, low voltage, and machinery. In the case of a conflict with Regulation (EU) 2024/1781, the relevant provisions of this Regulation should prevail. For other products, in order to avoid unnecessary burden for economic operators, the need may arise to determine the conditions under which the fulfilment of obligations under other Union law also fulfils certain obligations under this Regulation. Therefore the power to adopt acts in accordance with Article 290 TFEU should be delegated to the Commission to determine such conditions.(33)In order to create an incentive for compliance, the manufacturer of construction products should be liable for incorrect declarations of performance and conformity.(34)The increased reuse of construction products is part of a shift towards a more circular economy and a reduction of the environmental and carbon footprint of construction. The second-hand market for construction products is currently not very developed and requirements for construction products which have previously been used vary widely amongst Member States. Therefore, used construction products, including other used items subject to this Regulation, should be subject to long-term harmonisation by establishing the possibility to develop dedicated harmonised technical specifications under this Regulation. Such harmonised technical specifications should be applicable to used products and as long as the used product is not waste or has ceased to be waste. The adoption of dedicated harmonised technical specifications for used products should not prejudice the scope and definition of waste under Directive 2008/98/EC of the European Parliament and of the CouncilDirective 2008/98/EC of the European Parliament and of the Council of 19 November 2008 on waste and repealing certain Directives (OJ L 312, 22.11.2008, p. 3).. However, products directly reused in a construction work should not be considered as placed on the market again and therefore not be subject to any measures under this Regulation.(35)In order to provide clarity about the extent of the harmonised zone, it is important that all harmonised technical specifications are explicit in whether they cover or exclude used products from their scope. The exclusion of used products from the scope of a harmonised technical specification should however not prevent economic operators from opting for the application of this Regulation as if the used product was new.(36)According to the definition of used products, harmonised technical specifications explicitly including used products within their scope should also apply to used products which have undergone a transformative process going beyond checking, cleaning or repairing recovery operations defined by the harmonised technical specification as non-essential transformative processes to the product’s performance. Remanufactured products should, regardless of the harmonised technical specification, benefit from not having to include events before the product’s last deinstallation when calculating its environmental impact over its life cycle. Remanufactured products should also benefit from requirements or incentives that promote a high recycled content.(37)To enhance access to easily available and comprehensive information on construction products, thereby contributing to their safety, functionality and sustainability, it should be ensured that the declaration of performance and conformity provides all information necessary for users and authorities. In view of its utility for users, manufacturers should be able to include into that declaration additional information, provided that the declarations of performance and conformity remain uniform and easily readable and that they are not abused as advertisement.(38)In order to reduce the burden for economic operators, and in particular manufacturers, economic operators issuing declarations of performance and conformity should be allowed to provide copies of those declarations by electronic means, and be authorised to make them available on websites on the conditions that they are unamendable, human and machine readable, available, accessible and unequivocally linked to the product. In order to simplify supply chain communication, declarations of performance and conformity should allow the user – by means of an IT application – to check conformity with the application rules of the Member State where the product is used. An important prerequisite for machine-readable declarations is a standardised IT format, which is required for each harmonised technical specification.(39)In order for the manufacturers to demonstrate that the construction products benefitting from the free movement of goods fulfil relevant Union requirements, it is necessary to require a declaration of conformity complementing the declaration of performance, thus also bringing the regulatory system for construction products closer to Regulation (EC) No 765/2008 of the European Parliament and of the CouncilRegulation (EC) No 765/2008 of the European Parliament and of the Council of 9 July 2008 setting out the requirements for accreditation and repealing Regulation (EEC) No 339/93 (OJ L 218, 13.8.2008, p. 30).. However, in order to minimise the potential administrative burden, the declaration of conformity and the declaration of performance should be combined. The administrative burden on SMEs should be further minimised through targeted simplification provisions, including sharing test results, recognition of certificates, cascading of technical documentation and declaration without assessment, permitting micro-enterprises to use the more lenient assessment and verification system and reducing the requirements for custom-made non-series products. When such products are installed in an identified single construction work exemptions from the obligation to draw up a declaration of performance and conformity should be possible. In cases where a manufacturer fulfils the criteria for both the application of a simplified procedure and an exemption from the obligation to draw up a declaration of performance and conformity, it should be given the opportunity to choose one of them, or to provide a declaration of performance and conformity without applying the simplified procedure, so as to better adapt its offer to the needs of potential customers.(40)In order to reach alignment with other product legislation and subject to the general principles of Regulation (EC) No 765/2008, the CE marking should be affixed only to construction products for which the manufacturer has drawn up a declaration of performance and conformity. The manufacturer thereby assumes the responsibility for the conformity of the product with the declared performance and the applicable product requirements.(41)The procedural rights of all economic operators and natural or legal persons acting on their behalf in relation to measures, decisions or orders taken by market surveillance authorities and other competent national authorities need to be ensured in line with Regulation (EU) 2019/1020 of the European Parliament and of the CouncilRegulation (EU) 2019/1020 of the European Parliament and of the Council of 20 June 2019 on market surveillance and compliance of products and amending Directive 2004/42/EC and Regulations (EC) No 765/2008 and (EU) No 305/2011 (OJ L 169, 25.6.2019, p. 1).. It is necessary that Member States ensure that adequate appeal procedures against such measures, decisions or orders are in place.(42)To ensure functionality, safety and sustainability of construction products, and by extension of construction works, all economic operators intervening in the supply and distribution chain should take appropriate measures to ensure that they place, make available, or support making available on the market only construction products which are in compliance with the binding Union requirements. In order to improve the legal clarity, it is necessary to set explicitly the obligations of economic operators.(43)It is necessary for manufacturers of construction products to determine the product type in a precise and unequivocal manner in order to ensure a precise basis for assessing the compliance of such product with Union requirements. At the same time, in order to avoid circumvention of the applicable requirements, manufacturers should be prohibited from creating ever new product types where the products in question are, in view of the crucial characteristics, identical.(44)On the internal market, the CE marking should be the only marking demonstrating compliance with assessment methods in relation to essential characteristics covered by harmonised technical specifications. In order to avoid market fragmentation and misleading claims resulting from the application of different assessment methods, the CE marking should be the only marking allowed on products covered by harmonised technical specification indicating that the product in question has been assessed in relation to the essential characteristics covered by harmonised technical specifications and is compliant with the applicable product requirements. The market for construction products faces a proliferation of markings which often create confusion and distrust among market players but also mislead consumers. The use of additional markings negatively impacts the probative value of the CE marking when based on assessment methods which are different than those defined in the relevant harmonised technical specifications. In addition, SMEs cannot always benefit from such markings, creating a distortion among market players and potentially hindering market access. Those additional markings should therefore not be affixed to the products in combination with the CE marking. However, this prohibition does not prevent products which bear other markings from being placed on the single market, providing such markings do not mislead the consumer or create confusion with the CE marking. In addition, the markings should not impair the visibility, legibility or meaning of the CE marking. As such, these markings should not display any information, text or claims in relation to the product’s performance.(45)To avoid misleading claims, any claims made by manufacturers of construction products should be based on an assessment method contained in harmonised technical specifications where available.(46)Technical documentation about construction products, drawn up by the manufacturer, facilitates the verification of those products by competent national authorities and notified bodies against the Union requirements. To enhance access to comprehensive information, that technical documentation should include the necessary information to validate the calculation substantiating the assessment of the environmental sustainability of the construction product.(47)To create transparency for users of construction products and to avoid inappropriate use of those products, construction products and their intended use should be precisely identified by the manufacturer. For the same reason, the manufacturer should make clear whether the construction products are intended for professional use. To ensure that construction products can be traced back, manufacturers should indicate manufacturer-specific unique identification code of the product type on the product or, where this is not possible e.g. due to the product’s size or surface, on an affixed label, on the packaging or, where that is not possible either, in a document accompanying the product.(48)To ensure that requirements of this Regulation are fulfilled, manufacturers should actively search, store and evaluate information and take appropriate measures where non-conformity or under-performance has been confirmed or where there is a risk.(49)To achieve the goals of the European Green Deal and of the Circular Economy Action Plan, the Commission should have the possibility to specify minimum threshold levels for the environmental performance of construction products and product environmental requirements preventing and reducing the impact that construction products have on the environment. However, the "safety first" principle, applicable both for the construction product and the construction works, should in all instances be respected, and should encompass the protection of health.(50)With the goals of ensuring sustainability and durability of construction products, manufacturers should ensure that products can be used for as long as possible. Such long use requires adequate design, use of reliable parts, reparability of products, availability of information on repair and access to spare parts. In the event that the spare parts are not commonly available in the market, the Commission should be empowered to require from the manufacturer to ensure the availability of these spare parts at a reasonable and non-discriminatory price for a period of 10 years which may be extended if the availability for a longer period of time is expected to increase the life span of the product.(51)In view of enhancing the circularity of construction products, in line with the goals of the Circular Economy Action Plan and the waste hierarchy, product requirements should also be able to improve resource efficiency, prevent waste generation, prioritise repair, reuse and remanufacturing, favour the use of secondary materials and address the recyclability of the product and the production of by-products. Preparing for reuse, reuse, remanufacturing and recycling require certain design, namely by facilitating the separation of products, components and materials at deinstallation, deconstruction and demolition and at the later stage of recycling and, when possible, avoiding mixed, blended or intricate materials and substances of concern. As the usual instructions for use and safety information will not necessarily reach the economic operators in charge of preparing for reuse, reuse, remanufacturing and recycling, the necessary information in this regard should be made available in digital product passports accessible through data carriers and in manufacturer’s websites.(52)General product information, instructions for use and safety information are a vital tool to provide information that is sufficient to make knowledgeable decisions on purchase, installation, use, maintenance, dismantling, reuse and recycling of the product to a wide group in potential need of the information. Elements to be covered by the general product information, instructions for use and safety information should therefore be specified in this Regulation and guidance on how to typically cover these elements in relation to a certain product should be possible to include in performance harmonised standards. Such guidance should however not expand or restrict the responsibility for the manufacturer to provide information as set out in the Regulation. The Commission should be empowered to adopt delegated acts to ensure adequate and homogeneous implementation of the obligation to provide the general product information, instructions for use and safety information for specific product families or product categories when performance harmonised standards are not able to do it.(53)Some construction products become waste though they were never used. To avoid this waste of resources, the Regulation should not affect the possibility for Member States to oblige manufacturers to accept to regain, directly or via their importers and distributors, ownership of products that, after delivery onto a construction site or to the user, have not been used and are in a state equivalent to the one in which they were placed on the market.(54)In order to be able to make informed choices, users of construction products should be sufficiently well informed about the environmental performances of products, about their conformity with environmental requirements and of the degree of fulfilment of manufacturer’s environmental obligations in this regard. Therefore, the Commission is empowered to adopt delegated acts to establish specific labelling requirements.(55)The authorised representatives are often the only reachable persons in the case of imported products whilst manufacturers often attribute to them very limited tasks and do not provide them with all the necessary information to effectively represent the manufacturers. Hence, the role and responsibilities of authorised representatives should be strengthened and clearly set out in this Regulation, such as the tasks to be included in the mandate of the manufacturer. The mandate of the authorised representative should not include the drawing up of technical documentation. Nevertheless, manufacturers should be allowed to establish a separate contract with its authorised representative for this purpose, outside the scope of the mandate.(56)There should be always a manufacturer when the Regulation establishes obligations as regards the placing of a product on the market. When there is otherwise no manufacturer in the meaning of this Regulation, the distributor or importer should act as manufacturer and assume its responsibilities.(57)An economic operator who modifies a product or stores it in such a way that its performance or safety might be affected should be subject to the obligations of manufacturers, to ensure the verification whether performance or safety of the product are still the same. However, this obligation should not be imposed on an economic operator who repackages products, as otherwise secondary trade and thus free circulation of products would be hampered and repackaging in principle should not affect the performance or safety of the construction product. Still, and with the aim to preserve the performance and safety of products, the economic operator undertaking the repackaging should be responsible for the correct execution of these operations to ensure that the product is not damaged and that the users are still correctly informed in the language set out by the Member State where the products are made available.(58)Given its environmental effects, the calculation of the environmental sustainability of a construction product should also cover the packaging used or most likely to be used. The packaging of a product can also be vital to preserve its performance through the distribution chain to the user. Even though the packaging in itself is not included in other assessments of a product’s performance, all economic operators should, as part of their obligation to take necessary measures to ensure continued compliance of products with this Regulation, be responsible for using packaging suitable for preserving the performance and the compliance with the products’ requirements. The packaging could in itself pose a risk for users and the obligation to provide information on risks relating to the use of the product should take this into account.(59)In order to increase compliance of manufacturers with the obligations under this Regulation and to contribute to addressing the identified shortcomings and improve the market surveillance, fulfilment service providers, online market places and other market actors should actively contribute to ensuring that only compliant products reach the users.(60)To avoid circumvention of the obligations under this Regulation when the production technology involves several different actors who contribute to the design and manufacture of a construction product, it is necessary to establish a clearly defined manufacturer’s role where the natural or legal person who does the actual production of a construction product assumes the responsibilities under this Regulation in respect of the entire product, unless there is another person who either places the product on the market under his or her name or trademark, or assumes responsibility for the product by drawing up a declaration of performance and conformity. This is of particular importance in relation to 3D-printing, whereby a natural or legal person 3D-prints construction products and places them on the market. That person should fulfil the obligations incumbent on manufacturers including as regards the use of appropriate 3D-datasets and of materials which have undergone the procedures applicable to products as well as with regard to the correspondence of the information to be provided by the manufacturer of the 3D-dataset with the information to be provided by the manufacturer of the printing material.(61)In cases when the product is not intended to be used for construction but its appearance is likely to lead consumers to use the product in construction, the product is accompanied by instructions for use and safety information pursuant to Regulation (EU) 2023/988 of the European Parliament and of the CouncilRegulation (EU) 2023/988 of the European Parliament and of the Council of 10 May 2023 on general product safety, amending Regulation (EU) No 1025/2012 of the European Parliament and of the Council and Directive (EU) 2020/1828 of the European Parliament and the Council, and repealing Directive 2001/95/EC of the European Parliament and of the Council and Council Directive 87/357/EEC (OJ L 135, 23.5.2023, p. 1). or another applicable regulation indicating that despite its appearance it was not designed as a construction product. Market surveillance authorities are to take the appropriate measures, including the possibility to withdraw the product from the market, if its appearance could lead to confusion for the consumer or to misuse.(62)To clarify the applicability of this Regulation to online and other distance sales, it should be defined under which conditions a certain product is deemed to be offered to clients in the Union. As online trade has a higher likelihood of non-compliance, Member States should make a special effort to designate a single market surveillance authority for detecting distance sales offers targeting clients on their territory, so that the responsible market surveillance authorities can take appropriate measures. Offers using the currency of the Member States, available through an internet domain name which is registered in one of the Member States or which refers to the Union or one of the Member States, and dispatched to any Member State, should be considered targeted at customers in the Union. Other elements such as using an official language of a Member State may also be considered as an indication by market surveillance authorities as to whether the offer targets customers in the Union.(63)Digital technologies, which provide a significant potential for reducing administrative burden and costs for economic operators and authorities, while also fostering innovative and new business opportunities and models, are evolving at rapid pace. The uptake of digital technologies will also contribute significantly towards achieving the objectives of the Renovation Wave, including energy efficiency, life cycle assessments and monitoring and of the building stock.(64)In order to ensure a timely adoption of harmonised standards and European assessment documents, the Commission should have the possibility to make them mandatory with restrictions of their legal effects under this Regulation. It should be possible for such restrictions to cover, for example, outdated references to other standards or documents, provisions which contradict this Regulation or other Union law, provisions which contradict other harmonised standards, or provisions which are not in conformity with the demands to be met in relation to the basic principles and reference points set out in a standardisation request.(65)To ensure the coherence of the system, this Regulation should build on the horizontal legal framework for standardisation. Hence, Regulation (EU) No 1025/2012 should also apply to the extent possible to standards made mandatory in accordance with this Regulation. Regulation (EU) No 1025/2012 is thus to provide, among others, for a procedure for objections to harmonised standards where those standards do not entirely conform with applicable legal requirements or satisfy the requirements set out in the relevant standardisation request or other requirements of this Regulation.(66)The Commission should support European standardisation organisations in developing guidelines laying down a set of clear and stable rules for the whole standardisation process, including roles, responsibilities, competences and the general procedural deadlines for all stakeholders involved, as well as templates to be used. The Commission should also provide support to ensure the coherence and compliance of standards with legal requirements and should participate in the informal and formal discussions of European standardisation organisations developing the requested European standardisation deliverables, in particular on matters concerning the compliance of the standardisation deliverables with this Regulation and with other Union law. Those activities should benefit from the horizontal work developed in the context of the implementation of Regulation (EU) No 1025/2012.(67)When the Commission endorses by means of delegated acts proposals of European standardisation organisations related to voluntary or mandatory threshold levels and classes of performance in relation to the essential characteristics and those essential characteristics which always have to be declared by manufacturers, they should be accompanied by an impact assessment where required in accordance with the Interinstitutional Agreement of 13 April 2016 on Better Law-MakingOJ L 123, 12.5.2016, p. 1..(68)As they are not acts of general applicability but the first step of a two-step administrative procedure leading to the CE marking, European assessment documents should not qualify as harmonised technical specifications. However, basic principles of the elaboration of harmonised standards, such as transparency for competitors, can and should also apply to European assessment documents. Moreover, the European assessment documents should be referred to in the process of assessment and verification in the same way as harmonised standards. To create transparency for competitors, European assessment documents should be made publicly available and the references of all European assessment documents should be published in the Official Journal of the European Union.(69)Currently, the increasing number of hardly distinguishable European assessment documents which often have little added value when compared to others or existing harmonised standards, risks to slow down their publication. In order to deal with this risk in a cost-effective way, certain principles for the development and adoption of European assessment documents should be established or be made more concrete. Moreover, the control by the Commission should be enhanced.(70)Where the organisation of technical assessment bodies (TABs) considers the development of a European assessment document to be useful even without any demand from a manufacturer, the organisation of TABs should bring the issue to the attention of the Commission who should decide on requesting the development of the European assessment document taking into consideration the justification provided by the organisation of TABs and the market needs.(71)The requirements applicable to designating authorities of TABs should not fall behind those applicable to notifying authorities given the similarities between their respective roles. For the same reason, TABs should have the same degree of independence and control of decision-making as notified bodies.(72)In order to respond to a noteworthy percentage of notifications which were based on incomplete or erroneous assessments, in particular where legal bodies without own in-house technical competence were notified, it is necessary to make requirements for notified bodies more precise, namely with regard to their independence, delegation to other legal entities and own ability to perform; to require sufficient adequate qualified staffing of notified bodies and to verify the adequacy of the staffing, for which a qualification matrix can be an efficient tool; to ensure and verify that the notified body is effectively in control of staffing, attribution of external experts, procedures, criteria and decision-making, and not a subcontractor, subsidiary or another company belonging to the same family of companies; and to enlarge the documentation to be provided by bodies when applying for designation as notified body so as to provide a deeper and comparatively fairer basis for decision to notifying authorities.(73)In order to ensure the correct implementation of this Regulation, it is necessary to ensure that accreditation bodies take as a basis for accreditation this Regulation and not deviating standards. It is also important to ensure that the accreditation bodies assess the ability of the applicant body and not of a group of companies, as it is the applicant body itself that must be in control of future certification.(74)To reach a level playing field and to avoid legal uncertainty, the obligations of notified bodies should be more clearly defined and rendered explicit, and this both for their assessment and verification activities and the related aspects.(75)In order to avoid involvement between notified bodies’ staff and the manufacturers, it should be possible for the notified bodies to allow rotation between the personnel carrying out different conformity assessment tasks.(76)Authorities of Member States might have questions that only a certain notified body can answer. Notified bodies should thus respond also to the questions authorities of other Member States may have.(77)To enable authorities to more easily identify instances of non-compliance by notified bodies, manufacturers and products, and to ensure a level playing field, notified bodies should be empowered, and where the non-compliance can be clearly demonstrated even obliged to, proactively forward information on instances of non-compliance to relevant competent national authorities or notifying authorities. Notified bodies should however not trespass the information obligation by investigating other operators than their own clients or peers.(78)With a view to creating a level playing field for notified bodies and manufacturers, the coordination amongst notified bodies should be enhanced. As only half of the current notified bodies participate on their own initiative in the activities of the already currently existing notified body coordination group, direct participation or by means of designated representatives thereto should thus become mandatory.(79)The attempts of establishing simplified procedures for small and medium-sized enterprises in Regulation (EU) No 305/2011 and thus reducing the burden and costs on SMEs and microenterprises have not been entirely effective and have often remained misunderstood or not used due to the lack of awareness or the lack of clarity regarding their application. By addressing the identified shortcomings while building on the previously established rules, it is necessary to clarify and facilitate their application and hence achieve the objective of supporting SMEs while ensuring performance, safety and environmental sustainability of construction products.(80)The recognition of test results obtained by another manufacturer, provided for in Article 36(1), point (b), of Regulation (EU) No 305/2011, should be generalised, in order to generally reduce the burden of economic operators and namely manufacturers. Such recognition mechanism is particularly needed to avoid multiple assessment of environmental sustainability of raw materials, interim products and final products.(81)To ensure legal certainty in the event of safety or performance problems, such recognition should only be permitted where the assessed and verified economic operators agree to cooperate between themselves and with the notified bodies involved, including the necessary sharing of data.(82)The evaluation of Regulation (EU) No 305/2011 showed that market surveillance activities carried out at national level, widely vary in quality and effectiveness. In addition to measures set out in this Regulation and under relevant Union law in favour of better market surveillance, the compliance of economic operators, bodies and products with this Regulation should be facilitated by also involving third parties such as by the possibility of any natural or legal person to submit information on instances of non-compliance through a complaint portal established and maintained by the Commission. The handling of complaints adheres to the right to good administration, as outlined in Article 41 of the Charter of Fundamental Rights of the European Union. In handling the complaints the Commission should take into account the relevance and substantiation of the complaint by prioritising those complaints raising issues having particularly far-reaching negative impacts for citizens or the internal market. For a complaint to be considered substantiated the Commission should particularly check if the complaint manages to set out a grievance or if the grievance sets out an issue where the Commission has adopted a clear, public and consistent position which has been communicated to the complainant. The Commission should reply to the complainant without undue delay and efficiently transmit the complaints to the relevant Member States who should handle these complaints promptly and effectively in accordance with their legal frameworks and obligations.(83)To address the identified shortcomings with regards to the market surveillance under Regulation (EU) No 305/2011, this Regulation should contain more justified empowerments for market surveillance authorities and for the Commission that should enable authorities to act under all potential problematic circumstances.(84)Market surveillance practice has proved that when evaluating products, at a certain point in time, there is a risk of non-compliance but no non-compliance incidence whereas, at a later point in time, the opposite is to be stated. Moreover, there are situations where there is a non-compliance other than a formal one that does not trigger a risk. For these reasons, Member States should be empowered to act in all cases of suspected non-compliance or risk, whilst the definition of "product presenting a risk" has to be extended to include risk for the environment. It is necessary to offer Member States enough procedural flexibility to distinguish between high and low priority cases of non-compliance, whilst all Member States should also be informed about less important cases.(85)To ensure effective enforcement of the requirements and to strengthen market surveillance in Member States the Commission should issue guidelines for the application of this Regulation, as well as common practices and methodologies for effective market surveillance, including, for example, elements such as a recommended number and type of checks to be performed by the market surveillance authorities on specific product category or family or in relation to specific requirements. It is appropriate that such recommendations be based on good practices developed in the framework of market surveillance.(86)In addition, to strengthen the on average weak capacities of market surveillance authorities in terms of market surveillance and to further align with Regulation (EU) 2024/1781, it is necessary to provide more detailed administrative coordination support and to provide them with the right to retrieve costs of inspections and testing from economic operators in relation to non-compliant products.(87)To create an incentive for increasing the capacities of market surveillance authorities in terms of market surveillance and to reach alignment with Regulation (EU) 2024/1781, Member States should report on their market surveillance activities regarding products covered by this Regulation, including regarding the penalties imposed.(88)To better serve economic operators, product contact points for construction should become more effective and therefore should obtain more resources. In order to facilitate the work of economic operators, the tasks of product contact points for construction should be fine-tuned and extended so as to include information on product related provisions of this Regulation and on acts adopted in accordance with it. Member States should also raise economic operators’ awareness of the product contact points for construction within their territory.(89)It is necessary to establish an appropriate, efficient and cost-effective coordination mechanism to ensure a consistent application of the obligations and requirements set and to strengthen the overall system, also taking into consideration the fact that new interpretative questions may arise in relation to safety and sustainability of products and construction works. As diverging decisions create an uneven playing field, contribute to rendering the legal framework more complex, create barriers to the free movement of the internal market and additional administrative burden and costs on economic operators, such diverging decisions should be prevented by that coordination mechanism.(90)In particular, an information and communication system should therefore be established to collect questions related to interpretation, to find appropriate common solutions and to improve the sharing of information in this regard. To facilitate information sharing, such a system should rely on national systems. Those national systems should also identify cases of uneven application of this Regulation, to ensure that diverging practices do not become a common practice and permanent. The information and communication system should also deal with issues raised related to the emergence of new products or business models, unforeseen situations and to situations in which other provisions of Union law also apply.(91)Digitalisation and availability of product information increases transparency to the benefit of safety of products and the protection of the environment and health of persons while also reducing administrative burden and costs for economic operators. Accordingly, the power to adopt acts in accordance with Article 290 TFEU should be delegated to the Commission to establish a construction digital product passport system aligned to the extent possible to the digital product passport under Regulation (EU) 2024/1781.(92)To improve machine readability, it is necessary to establish a common data dictionary based on European standards, a tool to govern and publish the data structure and their meaningful definitions and descriptions for all relevant construction products. For each product family or product category, the data dictionary should include all the essential characteristics and other properties as set out in the harmonised technical specifications as well as other information required by this Regulation. A data dictionary harmonised at the Union level allows for the classification and use of structured definitions by both competent national authorities and in the further digitalisation of the construction sector, in particular in Building Information Modelling, building logbooks, digital passports and registries.(93)To improve their level of competence, harmonise their decision-making and create a level playing field for economic operators, trainings should be organised for market surveillance authorities, product contact points for construction, designating authorities, notifying authorities, and representatives of notified bodies and TABs. The same goals should also be pursued by exchanges of staff between the market surveillance authorities, notifying authorities and notified bodies of two or more Member States.(94)Member States do not always have the technical competence to fulfil all obligations incumbent on them in accordance with Union legislation cumulatively for all product sectors. They therefore obtain informal support, from other Member States. Since such support is unavoidable in some cases, this Regulation should set out the basic rules for such support, namely to clarify responsibilities.(95)Business on construction products becomes slowly but steadily more and more international. Hence, situations arise where non-compliance by economic operators based outside the Union need to be countered as well. Provisions on international cooperation should therefore be provided for in this Regulation.(96)A certain number of third countries applies Union product legislation or at least recognises certificates issued in accordance with it, be it on the basis of international agreements or unilaterally, both being in the interest of the Union. In order to give these third countries an incentive to continue this practice and other third countries to do the same, certain additional possibilities should be provided, on a case-by-case basis, to third countries applying Union product legislation or recognising certificates issued in accordance with it. For this reason, it should be possible, after consultation with Member States, to support these particularly cooperative third countries by allowing them to participate in certain trainings and to participate in the construction digital product passport system, to the information system for harmonised decision-making and to the information exchange amongst authorities. Moreover, for the same reason, it should be possible to inform these particularly cooperative third countries about non-compliant or risky products.(97)In order to incentivise the use of sustainable construction products whilst avoiding market distortions and to remain in line with Regulation (EU) 2024/1781, incentives for the use of sustainable construction products provided by Member States should target the most sustainable products. The Commission should furthermore have the possibility to coordinate Member States incentives in order to boost the demand of certain environmentally sustainable products. Member States might also provide incentives to promote environmentally friendly and sustainable construction products that are not covered by harmonised technical specifications in line with State aid rules.(98)Public procurement amounts to 14 % of Union’s GDP. In order to enhance the use of sustainable construction products, which would contribute to the objective of reaching climate neutrality, improve energy and resource efficiency and in the transition to a circular economy that protects public health and biodiversity and to reach alignment with Regulation (EU) 2024/1781, the public procurement practices of the Member States should comply with mandatory minimum performance requirements on environmental sustainability for construction products set out by delegated acts. The Commission should decide the essential characteristics to be addressed and its implementation in the form of one or more of the following: technical specifications, selection criteria, contract performance clauses or contract award criteria. The mandatory minimum performance requirements on environmental sustainability deal with essential characteristics only and do not pre-empt the possibility for Member States to be more ambitious in their contracts by requesting better performances for the relevant essential characteristics while respecting the harmonised zone.(99)Contracting authorities and contracting entities should, where appropriate, be required to align their procurement with specific green public procurement criteria, to be set out in the delegated acts referred to in this Regulation. The criteria for specific product families or product categories should be complied with where contracts require mandatory minimum environmental sustainability performance for construction products as regards their essential characteristics covered by harmonised technical specifications. Those minimum requirements should be established in accordance with transparent, objective and non-discriminatory criteria. When developing delegated acts related to green public procurement, the Commission should take due account of the Member States different geographical, social and economic circumstances. When considering the effect on the market situation, the Commission should take into account, among others, the effects of the requirements on competition, SMEs and the best environmental products and solutions available on the market. When considering the economic feasibility for contracting authorities and contracting entities, the Commission should take into account that different contracting authorities in different Member States might have different budgetary capacities. In duly justified cases, contracting authorities should be able to derogate from the requirements such as when there is only one supplier, there are no suitable tenders or its application would lead to a disproportionate cost.(100)In order to ensure the proper functioning of the internal market in the event of an internal market emergency as referred to in Regulation (EU) 2024/2748 of the European Parliament and of the CouncilRegulation (EU) 2024/2748 of the European Parliament and of the Council of 9 October 2024 amending Regulations (EU) No 305/2011, (EU) 2016/424, (EU) 2016/425, (EU) 2016/426, (EU) 2023/988 and (EU) 2023/1230 as regards emergency procedures for the conformity assessment, presumption of conformity, adoption of common specifications and market surveillance due to an internal market emergency (OJ L, 2024/2748, 8.11.2024, ELI: http://data.europa.eu/eli/reg/2024/2748/oj)., for the reasons set out in that Regulation, it is necessary to provide for rules on construction products designated as crisis-relevant goods, prioritisation of the assessment and verification of those products, assessment and declaration of performance based on standards and common specifications as well as on prioritisation of market surveillance activities and mutual assistance among authorities, in the case of an active internal market emergency mode under that Regulation.(101)In order to take into account technical progress and knowledge of new scientific evidence, ensure proper functioning of the internal market, facilitate access to information and ensure homogeneous implementation of rules, the power to adopt acts in accordance with Article 290 TFEU should be delegated to the Commission in respect of amending Annexes II, III, IV, V, VI, VII, IX and X and amending this Regulation to further specify, add and remove certain functionalities and revise certain provisions with a view to ensuring compatibility and interoperability with Regulation (EU) 2024/1781. For the same reasons the power to adopt acts in accordance with Article 290 TFEU should be delegated to the Commission to supplement this Regulation by: determining voluntary or mandatory threshold levels in relation to the essential characteristics, classes of performance in relation to the essential characteristics, and the essential characteristics which always have to be declared by manufacturers; determining elements of standardisation requests and conditions under which a product is to be deemed to satisfy a certain level or threshold level or to qualify for a class of performance without testing or without further testing; establishing product requirements in accordance with Annex III; establishing rules on the provision of general product information, instructions for use and safety information for the respective product family or product category; determining, for each product family or product category, the applicable assessment and verification system among those set out in Annex IX; laying down conditions under which obligations relating to the assessment of a product’s performance or the fulfilment of certain product requirements can be satisfied by the fulfilment of obligations under other Union legal acts; imposing in respect of certain product families and product categories an obligation on manufacturers to make available on the market specific spare parts not commonly available for the products they place on the market; establishing specific environmental sustainability labelling requirements for particular product families and product categories; setting up a construction digital product passport system; and by specifying mandatory minimum environmental sustainability requirements for construction products. It is of particular importance that the Commission carry out appropriate consultations during its preparatory work, including at expert level, and that those consultations be conducted in accordance with the principles laid down in the Interinstitutional Agreement of 13 April 2016 on Better Law-Making. In particular, to ensure equal participation in the preparation of delegated acts, the European Parliament and the Council receive all documents at the same time as Member States’ experts, and their experts systematically have access to meetings of Commission expert groups dealing with the preparation of delegated acts. When developing those acts, the Commission should aim at reducing the administrative burden for companies and take into account the needs of SMEs.(102)In order to ensure uniform conditions for the implementation of this Regulation, implementing powers should be conferred on the Commission. Those powers should be exercised in accordance with Regulation (EU) No 182/2011 of the European Parliament and of the CouncilRegulation (EU) No 182/2011 of the European Parliament and of the Council of 16 February 2011 laying down the rules and general principles concerning mechanisms for control by Member States of the Commission’s exercise of implementing powers (OJ L 55, 28.2.2011, p. 13)..(103)The Commission should adopt immediately applicable implementing acts where, in duly justified cases relating to health and safety of persons or the protection of the environment, imperative grounds of urgency so require.(104)Regulation (EU) 2019/1020 lays down rules on a horizontal framework for market surveillance and control of products entering the Union market. In order to ensure that products under this Regulation, which are benefiting from the free movement of goods within the Union, fulfil requirements providing a high level of protection of public interests, such as the protection of health and safety of persons and the protection of the environment, that Regulation should apply also to products covered by this Regulation, in so far as there are no specific provisions with the same objective, nature or effect in this Regulation.(105)To render the implementation of this Regulation more efficient and to reduce the burden for economic operators, it should be possible to make applications and decisions on paper or in a commonly used electronic format. To obtain legal certainty, applications and decisions should only be valid where the electronic signature fulfils the requirements of Regulation (EU) No 910/2014 of the European Parliament and of the CouncilRegulation (EU) No 910/2014 of the European Parliament and of the Council of 23 July 2014 on electronic identification and trust services for electronic transactions in the internal market and repealing Directive 1999/93/EC (OJ L 257, 28.8.2014, p. 73). and where the signing person is entrusted to represent the body or economic operator, in accordance with the law of the Member States or Union law respectively.(106)To further reduce the burden on economic operators, it should be possible to provide documentation in a commonly used electronic format, and to fulfil information requirements electronically by default.(107)In order to ensure a high level of compliance with this Regulation, Member States should lay down rules on penalties applicable to instances of non-compliance and ensure that those rules are enforced. The penalties provided for should be effective, proportionate and dissuasive.(108)In order to create legal certainty, it should be specified whether and for how long designations of product contact points for construction, TABs, or notified bodies and harmonised standards, European assessment documents, European technical assessments and notified bodies certificates or test reports adopted or issued under Regulation (EU) No 305/2011 maintain legal effects under this Regulation. The respective transitional periods should be long enough to avoid bottlenecks in respect of notified bodies and TABs designation and of the adoption or issuing of European assessment documents, European technical assessments, and notified body certificates or test reports.(109)To create legal certainty, it should be clarified for how long products placed on the market on the basis of European technical assessments issued in accordance with European assessment documents adopted under Regulation (EU) No 305/2011 may be placed on the market.(110)Both the essential characteristics of construction products and their assessment methods can only be determined by harmonised technical specifications to be developed for the various product families and product categories, or by European assessment documents. Accordingly, requirements and obligations incumbent on economic operators with regard to a certain product family or product category should only apply mandatorily as of 12 months after the entry into force of harmonised technical specification covering the respective product family or product category unless a later application date has been specified in the publication in the Official Journal of the European Union.(111)To facilitate a smooth phasing-in of future harmonised technical specifications and taking into consideration the time needed for drawing up the declaration of performance and conformity, economic operators should be permitted to opt for the voluntary application of this Regulation as from the entry into force of these harmonised technical specifications.(112)It is necessary to avoid that economic operators can permanently circumvent the application of this Regulation by applying the harmonised technical specifications adopted under Regulation (EU) No 305/2011. For this reason, the Commission should withdraw from the Official Journal of the European Union the references to harmonised standards and European assessment documents published in support of Regulation (EU) No 305/2011 and covering a certain product family or product category by the entry into application of harmonised technical specification adopted under this Regulation covering that respective product family or product category.(113)While the concept of basic requirements for construction works is kept as the technically necessary link between construction works and construction products, it should be made explicit that they do not constitute obligations incumbent upon economic operators or Member States seeing as the right to regulate construction works is a competence of Member States. In order to cover the environmental assessment of construction products as well as product requirements which exist even in current harmonised technical specifications, a more comprehensive Annex I should be developed, including also a detailed list of predetermined environmental essential characteristics related to life cycle assessment and a framework for the product requirements. On that occasion, overlaps between basic requirements for construction works should be eliminated and clarifications should be brought forward.(114)In order to reach a minimum control intensity of the assessment and verification of manufacturers by notified bodies and to create a level playing field both for manufacturers and notified bodies, Annex IX on assessment and verification systems should more precisely and comprehensively determine the tasks of manufacturers and notified bodies under different possible assessment and verification systems. Moreover, that Annex should determine the assessments and verifications to be undertaken to verify the environmental sustainability of products, in terms of product performance and product requirements. When the Commission defines the applicable assessment and verification system for a product family or product category, continuity with Regulation (EU) No 305/2011 and coherence across product families should be the guiding principles.(115)Since the objectives of this Regulation, namely to ensure the free movement of safe and sustainable construction products in the internal market, to contribute to the green and digital transition and to protect health and safety of persons and the environment, cannot be sufficiently achieved by the Member States, as Member States tend to establish very diverging requirements for construction products, with an uneven level of protection of health and safety of persons and of the environment, but can rather be better achieved at Union level by establishing a harmonised assessment framework for the performance of construction products and certain product requirements for the protection of health and safety of persons and of the environment, the Union may adopt measures, in accordance with the principle of subsidiarity as set out in Article 5 TEU. In accordance with the principle of proportionality as set out in that Article, this Regulation does not go beyond what is necessary in order to achieve those objectives,HAVE ADOPTED THIS REGULATION:
CHAPTER IGENERAL PROVISIONS
Article 1Subject matter and objectives1.This Regulation lays down harmonised rules for the placing and making available on the market of construction products, regardless of whether undertaken in the framework of a service or not, by establishing:(a)harmonised rules on how to express the environmental and safety performance of construction products in relation to their essential characteristics, including on life cycle assessment;(b)environmental, functional and safety product requirements for construction products.2.This Regulation also establishes:(a)rights and obligations for economic operators dealing with construction products or their components; and(b)obligations for other actors providing services linked to the manufacturing and commercialisation of products covered by this Regulation.3.This Regulation aims to contribute to the efficient functioning of the internal market by ensuring the free movement of safe and sustainable construction products in the Union. It also aims to contribute to the objectives of a green and digital transition by preventing and reducing the impact that construction products have on the environment and on the health and safety of persons.
Article 2Scope1.This Regulation applies to construction products, including used products, and to the following items:(a)key parts of products; and(b)parts or materials intended to be used for products covered by this Regulation, if the manufacturer of those parts or materials so requests.2.This Regulation does not apply to:(a)lifts subject to Directive 2014/33/EU of the European Parliament and of the CouncilDirective 2014/33/EU of the European Parliament and of the Council of 26 February 2014 on the harmonisation of the laws of the Member States relating to lifts and safety components for lifts (OJ L 96, 29.3.2014, p. 251)., escalators or their components;(b)requirements or performance assessment subject to Directive (EU) 2020/2184 of the European Parliament and of the CouncilDirective (EU) 2020/2184 of the European Parliament and of the Council of 16 December 2020 on the quality of water intended for human consumption (OJ L 435, 23.12.2020, p. 1). and covered by the delegated acts of the Commission referred to in Article 11(8) of that Directive.3.Member States may exempt from the application of this Regulation products falling within its scope that are placed on the market in the outermost regions of the Union within the meaning of Article 349 TFEU. Member States shall notify to the Commission and to the other Member States the national laws, regulations and administrative provisions providing such exemptions. They shall ensure that exempted products do not bear the CE marking referred to in Article 17. Products placed on the market on the basis of that exemption shall not be deemed to have been placed on the market in the Union within the meaning of this Regulation.
Article 3DefinitionsFor the purposes of this Regulation, the following definitions shall apply:(1)"construction product" means any formed or formless physical item, including 3D-printed products, or a kit that is placed on the market, including by means of supply to the construction site, for incorporation in a permanent manner into construction works or parts thereof with the exception of items that need first to be integrated into a kit or another construction product prior to being incorporated in a permanent manner into construction works;(2)"product" means a construction product or other item falling within the scope of this Regulation as set out in Article 2;(3)"permanent" means intended to remain in the construction work, or in parts thereof, after the completion of the construction or renovation process;(4)"making available on the market" means any supply of a product for distribution or use on the Union market in the course of a commercial activity, whether in return for payment or free of charge, regardless whether in the framework of providing a service or not;(5)"placing on the market" means the first making available of a product on the Union market, or the first making available on the Union market of a used product after a deinstallation of such a product;(6)"performance" means the degree to which a product has certain scalable essential characteristics;(7)"essential characteristics" means those characteristics of the product which relate to the basic requirements for construction works set out in Annex I, and those which are listed as predetermined environmental essential characteristics in Annex II;(8)"product requirement" means a characteristic, as set out in Annex III, which a product must have before it can be placed on the market;(9)"economic operator" means the manufacturer, the authorised representative, the importer, the distributor, the fulfilment service provider or any other natural or legal person who is subject to this Regulation in relation to the manufacturing or remanufacturing of products, including products to be reused, or to making those products available on the market, in accordance with this Regulation;(10)"manufacturer" means a "manufacturer" as defined in Article 3, point (8), of Regulation (EU) 2019/1020;(11)"3D-dataset" means a set of numerical data describing the shape of an object by its outer dimensions and its cavities;(12)"construction works" means buildings and civil engineering works whether over or in the ground or water, including but not limited to roads, bridges, tunnels, pylons and other facilities for transport of electricity, communication cables, pipelines, aqueducts, dams, airports, ports, waterways, and installations which are the bases for the rails of railways;(13)"level" means the result of the assessment of the performance of a product in relation to its essential characteristics, expressed as a numerical value;(14)"class" means a range of levels, delimited by a minimum and a maximum value, of performance of a product;(15)"threshold level" means a minimum or maximum performance level of a product with regard to a certain essential characteristic;(16)"key part" means a part which is used as a component or spare part for a product and which has been specified by a harmonised technical specification as essential for the characterisation, safety or performance of a product;(17)"kit" means a product placed on the market by a single economic operator as a set of at least two separate items, none of which needs to be a product itself, intended to be incorporated together into construction works;(18)"European assessment document" or "EAD" means a document adopted by the organisation of technical assessment bodies for the purposes of issuing European technical assessments;(19)"European technical assessment" or "ETA" means the documented assessment of the performance of a product, in relation to its essential characteristics, in accordance with the respective European assessment document;(20)"used product" means a product that is not waste or has ceased to be waste in accordance with Directive 2008/98/EC, and which has been installed at least once into a construction work, and that:(a)has not undergone a process going beyond checking, cleaning or repairing recovery operations by which products or components of products are prepared so that they can be reused for construction purposes without any other pre-processing; or(b)has been subject to a transformative process going beyond checking, cleaning and repairing recovery operations which, according to the applicable harmonised technical specification, is qualified as non-essential to the product’s performance;(21)"intended use" means the purpose of a product as set out in the applicable harmonised technical specifications or European assessment documents;(22)"declared use" means the use intended by the manufacturer, including the conditions for usage, as set out in technical documentation, on labels, in general product information, in instructions for use, in safety information, or in publicity material;(23)"repair" means the process of fixing a faulty product or replacing its defective components, in order to return the product to a condition where it can fulfil its declared use;(24)"maintenance" means an action carried out to keep a product in a condition where it is able to function as specified;(25)"remanufactured product" means a product that is not waste, or has ceased to be waste in accordance with Directive 2008/98/EC, which has been installed at least once into a construction work, and that has been subject to a transformative process going beyond checking, cleaning and repairing recovery operations which, according to the applicable harmonised technical specification, are qualified as essential to the product’s performance;(26)"risk" means "risk" as defined in Article 3, point (18), of Regulation (EU) 2019/1020;(27)"product type" means the abstract model of individual products, determined by the intended use and a set of characteristics which exclude any variation with regard to performance or to the fulfilment of product requirements set out in or in accordance with this Regulation, whilst identical products of different manufacturers belong to different product types;(28)"state of the art" means a way of achieving a certain goal which is either the most effective and advanced or close to it, or a way which is currently possible by applying common technologies, whether or not it is the most technologically advanced solution;(29)"recycling" means "recycling" as defined in Article 3, point (17), of Directive 2008/98/EC;(30)"fulfilment service provider" means a "fulfilment service provider" as defined in Article 3, point (11), of Regulation (EU) 2019/1020;(31)"product family" means all product types belonging to one of the families listed in Annex VII;(32)"product category" means a subset of the product types of a certain product family encompassing those product types which have in common a certain intended use as specified in harmonised technical specifications or European assessment documents;(33)"factory production control" means the documented, continuous and internal production control in a manufacturing plant with regard to certain parameters or quality aspects, reflecting the specificities of a respective product family or product category and manufacturing processes, and which aims at the constancy of performance or at the continuous fulfilment of product requirements, executed in accordance with Annex IX;(34)"importer" means an "importer" as defined in Article 3, point (9), of Regulation (EU) 2019/1020;(35)"distributor" means any natural or legal person in the supply chain, other than the manufacturer or the importer, who makes a product available on the market, including by offering products for sale, hire or hire purchase, or displaying products to customers or installers in the course of a commercial activity, and including through distance selling, whether or not in return for payment;(36)"authorised representative" means any natural or legal person established in the Union who has received a written mandate from a manufacturer to act on that manufacturer’s behalf in relation to specified tasks with regard to the manufacturer’s obligations under this Regulation;(37)"individually manufactured" means that, due to the specifications of the client, there is a need for readjustment of the production process for manufacture when compared with all other products produced for other clients by the economic operator in question;(38)"micro-enterprise" means a "micro-enterprise" as defined in Article 2(3) of the Annex to Commission Recommendation 2003/361/ECCommission Recommendation 2003/361/EC of 6 May 2003 concerning the definition of micro, small and medium-sized enterprises (OJ L 124, 20.5.2003, p. 36).;(39)"custom-made" means that, due to the specifications of the client, there is a variation in terms of size or material when compared with all other products produced for other clients by the economic operator in question;(40)"permalink" means an internet link to a website which is stable both for its content and the address ("URL");(41)"data carrier" means a linear bar code symbol, a two-dimensional symbol, or other automatic identification data capture medium that can be read by a device;(42)"harmonised technical specifications" means the performance harmonised standards which have been made mandatory for the purposes of the application of this Regulation in accordance with Article 5(8), the implementing acts referred to in Article 6(1) and the delegated acts referred to in Article 7(1), Article 9(3) and Article 10(2);(43)"European standardisation organisation" means a "European standardisation organisation" as defined in Article 2, point (8) of Regulation (EU) No 1025/2012;(44)"non-series process" means a process that is neither predominantly automated or predominantly carried out using assembly-line techniques, nor repeated very often in relation to the volume of production by the economic operator concerned or the economic operators belonging to the same group of companies, determined by a common controlling natural or legal person, or the same organisational structure;(45)"withdrawal" means "withdrawal" as defined in Article 3, point (23), of Regulation (EU) 2019/1020;(46)"recall" means "recall" as defined in Article 3, point (22), of Regulation (EU) 2019/1020;(47)"online marketplace" means a provider of an intermediary service using an online interface which enables customers to conclude distance contracts with economic operators for the sale of products;(48)"online interface" means an "online interface" as defined in Article 3, point (15), of Regulation (EU) 2019/1020;(49)"supplier" means any natural or legal person providing raw materials, intermediate products, or used products to manufacturers or to other persons providing raw materials, intermediate products, or used products to manufacturers;(50)"service provider" means any natural or legal person providing a service to a manufacturer or to a supplier of a key part, provided that the service is relevant for the manufacturing of products, including to their design, or to their deinstallation in the case of used products;(51)"accreditation" means "accreditation" as defined in Article 2, point (10), of Regulation (EC) No 765/2008;(52)"market surveillance authority" means a "market surveillance authority" as defined in Article 3, point (4), of Regulation (EU) 2019/1020;(53)"life cycle" means the consecutive and interlinked stages of a product’s life, from raw material acquisition or generation from natural resources, or in the case of products which have previously been incorporated into construction works, from the latest deinstallation from the construction work, to final disposal;(54)"single liaison point" means the authority designated as the focal point for contacts with the Commission and other Member States on construction product related issues;(55)"notified body" means a conformity assessment body authorised to carry out third-party assessment and verification tasks under this Regulation that has been duly notified;(56)"notifying authority" means the single public administration body, designated in accordance with this Regulation, in charge of the notification and monitoring of notified bodies;(57)"technical assessment body" or "TAB" means a body, designated in accordance with this Regulation, that issues European technical assessments on the basis of European assessment documents;(58)"designating authority" means the single public administration body, designated in accordance with this Regulation, in charge of the designation and monitoring of TABs in a Member State;(59)"product presenting a risk" means a product that, whenever during its entire life cycle, has an inherent potential to affect adversely the health and safety of persons, the environment or the fulfilment of basic requirements for construction works when incorporated in those works, to a degree which, taking account of the state-of-the-art, goes beyond what is considered reasonable and acceptable in relation to its intended use and under normal or reasonably foreseeable conditions of use;(60)"product presenting a serious risk" means a "product presenting a serious risk" as defined in Article 3, point (20), of Regulation (EU) 2019/1020;(61)"by-product" means a "by-product" within the meaning of Article 5 of Directive 2008/98/EC;(62)"recyclability" means the capability of a material or product to be effectively and efficiently separated, collected, sorted and aggregated in specific waste streams for the purpose of being recycled into secondary raw materials while minimising the loss of quality or functionality compared to the relevant primary raw material;(63)"crisis-relevant goods" means "crisis-relevant goods" as defined in Article 3, point (6), of Regulation (EU) 2024/2747 of the European Parliament and of the CouncilRegulation (EU) 2024/2747 of the European Parliament and of the Council of 9 October 2024 establishing a framework of measures related to an internal market emergency and to the resilience of the internal market and amending Council Regulation (EC) No 2679/98 (Internal Market Emergency and Resilience Act) (OJ L, 2024/2747, 8.11.2024, ELI: http://data.europa.eu/eli/reg/2024/2747/oj).;(64)"internal market emergency mode" means "internal market emergency mode" as defined in Article 3, point (3), of Regulation (EU) 2024/2747.
Article 4Working plan and preparatory phase for the development of harmonised technical specifications1.The Commission shall be supported by an expert group ("the Construction Products Regulation Acquis Expert Group" or "CPR Acquis Expert Group"). The CPR Acquis Expert Group shall be composed at least of experts designated by the Member States, representatives of European standardisation organisations and of relevant European stakeholder organisations receiving Union financing under Regulation (EU) No 1025/2012. The CPR Acquis Expert Group shall support the Commission in processing Member States’ requests for Union harmonisation through harmonised technical specifications. In particular, the CPR Acquis Expert Group shall assist the Commission in establishing and updating a working plan for the development of harmonised technical specifications, in preparing the technical content related to harmonised technical specifications, in deciding on the need to launch the procedures in relation to harmonised technical specifications that present deficiencies, are unavailable, or not able to cover immediate regulatory needs, and in determining the inclusion of used products in harmonised technical specifications.2.After consulting the CPR Acquis Expert Group, the Commission shall establish a working plan for the development of harmonised technical specifications for product families listed in Annex VII, including product requirements as well as general product information, instructions for use and safety information, covering at least the following three-year period. The Commission shall set the priorities of the working plan using a transparent and balanced methodology, which shall be published together with the working plan. That methodology shall at least reflect the regulatory needs of the Member States, the safety issues related to construction works and products and the climate and circular economy goals of the Union.The Commission shall publish the first working plan no later than 8 January 2026.The Commission shall renew and update the working plan at least every three years. It shall publish the working plan for the following three-year period one year before the expiration of the working plan in force.The Commission shall inform the European Parliament and the Member States annually about progress in implementing the working plan.If the Commission considers that it cannot achieve the goals set out in the working plan, it shall amend it accordingly without undue delay, and shall inform the European Parliament and the Member States about the reasons thereof.3.Following the working plan established under paragraph 2, Member States shall communicate to the Commission and the CPR Acquis Expert Group the essential characteristics they require for a product family or product category, and the assessment methods, threshold levels or classes of performance, as well as the product requirements, that they deem necessary.When Member States communicate their regulatory needs to the Commission pursuant to the first subparagraph, the Commission shall integrate them or shall provide a statement of reasons why it is not possible to do so.4.On the basis of the basic requirements for construction works set out in Annex I and taking into account the regulatory needs communicated by Member States in accordance with paragraph 3 of this Article, as well as the safety, environmental, circularity and climate objectives of the Union, the Commission, with the support of the CPR Acquis Expert Group, shall identify the technical aspects needed to prepare standardisation requests, including the relevant essential characteristics. Those essential characteristics and the list of predetermined environmental essential characteristics set out in Annex II shall constitute the basis for the preparation of the standardisation requests referred to in Article 5(2) and of the implementing acts referred to in Article 6(1).5.The Commission shall ensure that essential characteristics are covered by harmonised technical specifications to the extent that the development of such specifications is technically and economically proportionate.6.The Commission, with the support of the CPR Acquis Expert Group, shall identify the product requirements referred to in Article 7, as well as other harmonised technical specifications, and shall determine whether used products are to be covered by or excluded from a standardisation request or a harmonised technical specification. The CPR Acquis Expert Group shall, as a matter of urgency, be consulted on notifications from Member States made in accordance with Article 11(5).7.The Commission is empowered to adopt delegated acts in accordance with Article 89 to amend:(a)the list of predetermined environmental essential characteristics set out in Annex II in order to adapt it to technical progress and new environmental risks and to comply with the priorities established pursuant to paragraph 2 of this Article based on the regulatory needs of the Member States;(b)the product families listed in Annex VII, to adapt them to technical progress and to the regulatory needs of the Member States.
Article 5Harmonised standards laying down essential characteristics dealing with performance1.The methods and the criteria for assessing the performance of a product in relation to its essential characteristics shall be laid down in harmonised standards made mandatory by means of the implementing acts referred to in paragraph 8 ("performance harmonised standards"). Performance harmonised standards shall, where appropriate and without endangering the accuracy, reliability or stability of the results, provide methods for assessing the performance of the products in relation to their essential characteristics that are less onerous than testing.2.The Commission shall, in accordance with Article 10 of Regulation (EU) No 1025/2012, request one or more European standardisation organisations to draft harmonised standards laying down essential characteristics and their assessment methods for one or more product families, or for one or more product categories within a family. The standardisation request shall set out the basic principles and reference points for the establishment of those essential characteristics and their assessment methods. The standardisation request shall explicitly state whether it covers or excludes used products from the scope of the request.3.As part of the standardisation requests referred to in paragraph 2 of this Article, the Commission may also request the European standardisation organisations to provide the technical details necessary for the implementation of the assessment and verification system that is to be applied in accordance with the delegated acts referred to in Article 10(2).4.The standardisation requests referred to in paragraph 2 may include a request to propose one or more of the following elements:(a)voluntary or mandatory threshold levels in relation to the essential characteristics;(b)classes of performance in relation to the essential characteristics;(c)those essential characteristics which always have to be declared by manufacturers.Such standardisation requests shall set out the basic principles and reference points for the establishment of the elements requested.5.Where it has included with its standardisation request a request for a proposal in accordance with paragraph 4 of this Article, the Commission is empowered to adopt delegated acts in accordance with Article 89 to supplement this Regulation by determining, for the product families or product categories and for the elements covered by that request, the elements referred to in paragraph 4, first subparagraph of this Article.After consulting the CPR Acquis Expert Group, the Commission may deviate from the proposals of the European standardisation organisation.The Commission is empowered to adopt delegated acts, irrespective of any prior standardisation request but on the advice of the CPR Acquis Expert Group, in accordance with Article 89 to supplement this Regulation by determining the elements set out in paragraph 4, first subparagraph of this Article in relation to any of the groupings of essential characteristics of a horizontal nature listed in Annex X.6.In cases where, on the basis of the nature or technical characteristics of a product, it is apparent that testing would be unnecessary or redundant, the Commission is empowered to adopt delegated acts in accordance with Article 89 to supplement this Regulation by laying down conditions under which a product is to be deemed to satisfy a certain level, threshold level or to qualify for a class of performance without testing, or without further testing.7.The Commission shall assess the compliance of harmonised standards with the relevant standardisation requests, with this Regulation and with other Union law, including general principles of law. The Commission may assess whether harmonised standards comply with other harmonised standards under this Regulation or with other harmonised standards the references of which have been published in the Official Journal of the European Union.The Commission shall carry out the assessment referred to in the first subparagraph of this paragraph and present its reasons in writing to the relevant European standardisation organisation and to the CPR Acquis Expert Group within six months after the relevant harmonised standard has been transmitted to it. Where the Commission considers that a standard, or a part thereof, is unsatisfactory, it shall specify the deficiencies. In order for the Commission to fulfil that obligation within that timeframe, the European standardisation organisations shall regularly inform the Commission of the progress and content of the European standardisation deliverable in accordance with Article 10(5) of Regulation (EU) No 1025/2012.8.Where a harmonised standard is in conformity with applicable legal requirements and satisfies the requirements to be met in relation to the basic principles and reference points set out in the standardisation request, as well as in relation to the essential characteristics to be covered in view of the basic requirements for construction works, the Commission shall without delay adopt an implementing act making that standard mandatory. One year after such adoption the performance harmonised standard shall become mandatory for the purposes of this Regulation unless a later application date has been specified in the implementing act. A later application date shall be specified only in exceptional cases and its use shall be duly justified. A performance harmonised standard may be voluntarily applied from the date of the adoption of the implementing act.Where the Commission considers a harmonised standard or a part thereof to be unsatisfactory, it may adopt an implementing act making that harmonised standard mandatory with restrictions.The implementing acts referred to in the first and second subparagraph shall be adopted in accordance with the advisory procedure referred to in Article 90(2).Where it is not possible to make a harmonised standard mandatory with restrictions, the Commission may adopt an implementing act in accordance with Article 6.9.When a Member State, the European Parliament or the Commission, the last with the support of the CPR Acquis Expert Group, considers that a performance harmonised standard does not entirely fulfil the applicable legal requirements or satisfy the demands to be met in relation to the essential characteristics to be covered in view of the basic requirements for construction works, the procedure for formal objections to harmonised standards as set out in Article 11 of Regulation (EU) No 1025/2012 shall apply.10.The Commission is empowered to adopt delegated acts in accordance with Article 89 to amend Annex X by adding additional groupings of essential characteristics of a horizontal nature.
Article 6Other harmonised technical specifications laying down essential characteristics1.While priority shall be given to the elaboration of standards, by way of derogation from Article 5(1) to (4) of this Regulation, in order to cover the regulatory needs of Member States and to pursue the goals of Article 114 TFEU, the Commission may adopt implementing acts laying down essential characteristics, their assessment methods and technical details pursuant to Article 5 of this Regulation for one or more product families or for one or more product categories within a family.Those implementing acts shall be adopted only if the following conditions are fulfilled:(a)the Commission has requested, pursuant to Article 5(2), one or more European standardisation organisations to draft a harmonised standard and:(i)the request has not been accepted; or(ii)the harmonised standard addressing that request is not delivered within the deadline set in accordance with Article 10(1) of Regulation (EU) No 1025/2012 and no later than three years after the acceptance of the standardisation request; or(iii)the harmonised standard does not comply with the request; and(b)no implementing act, as referred to in Article 5(8), first subparagraph, making mandatory a harmonised standard covering the essential characteristics, their assessment methods and technical details pursuant to Article 5 was adopted in the last 5 years, or such an implementing act was adopted within the last five years, but with restrictions, as referred to in Article 5(8), second subparagraph.Those implementing acts shall be adopted in accordance with the examination procedure referred to in Article 90(3).2.Before preparing a draft implementing act referred to in paragraph 1 of this Article, the Commission shall inform the committee referred to in Article 22 of Regulation (EU) No 1025/2012 that it considers that the conditions in paragraph 1 of this Article are fulfilled.3.When preparing the draft implementing act, the Commission shall take into account the views of relevant bodies and of the CPR Acquis Expert Group and shall duly consult all relevant stakeholder organisations receiving Union financing under Regulation (EU) No 1025/2012.4.Where an implementing act referred to in paragraph 1 of this Article covers the same essential characteristics or assessment methods in relation to a specific product family or product category as a harmonised standard the reference of which has been published in the Official Journal of the European Union or in respect of which an implementing act referred to in Article 5(8) has been adopted, the Commission shall withdraw from the Official Journal of the European Union the reference of that harmonised standard or repeal that implementing act. Where the implementing act referred to in paragraph 1 of this Article only partially covers the harmonised standard, the Commission shall retain the implementing act laying down a harmonised standard that is subject to restrictions.5.When a Member State or the European Parliament considers that an implementing act adopted in accordance with paragraph 1 does not entirely satisfy the requirements to be met in relation to the essential characteristics to be covered in view of the basic requirements for construction works, it shall inform the Commission thereof, by submitting a detailed explanation. The Commission shall assess that detailed explanation and may, if appropriate, amend the implementing act in question.6.The Commission shall follow the procedure in Article 5 to request any revision or update of the essential characteristics or assessment methods in relation to the same product families or product categories as those covered by the implementing act referred to in paragraph 1 of this Article. Where the harmonised standard delivered by the European standardisation organisation is suitable to be adopted in accordance with Article 5(8), the Commission shall repeal the implementing act adopted in accordance with paragraph 1 of this Article, or the parts thereof which cover the same essential characteristics or assessment methods in relation to the same product families or product categories as those covered by the harmonised standard.
Article 7Product requirements and harmonised standards conferring a presumption of conformity1.Where a product family, or one or more product categories within a product family, is covered either by a performance harmonised standard or by an implementing act referred to in Article 6(1), the Commission is empowered to adopt delegated acts in accordance with Article 89 to supplement this Regulation, by establishing product requirements in accordance with Annex III for that product family or product category, or for parts thereof.2.Prior to their placing on the market, products covered by this Regulation shall satisfy the applicable product requirements.3.The Commission may, in accordance with Article 10(1) of Regulation (EU) No 1025/2012, request one or more European standardisation organisations to draft harmonised standards conferring the presumption of conformity ("voluntary harmonised standards") for the product requirements established by delegated acts referred to in paragraph 1 of this Article.4.Where a voluntary harmonised standard requested in accordance with paragraph 3 is adopted by a European standardisation organisation and proposed to the Commission for the purpose of publishing its reference in the Official Journal of the European Union, the Commission shall assess the voluntary harmonised standard in accordance with Regulation (EU) No 1025/2012.5.Where a voluntary harmonised standard is in conformity with the applicable legal requirements and satisfies the requirements in relation to the product requirements set out in the standardisation request, the Commission shall without delay publish the reference of that standard in the Official Journal of the European Union.6.Where the reference of a voluntary harmonised standard cannot be published in the Official Journal of the European Union, the Commission may publish such a reference with restrictions. Where a reference of a voluntary harmonised standard cannot be published in the Official Journal of the European Union and cannot be published as a reference with restrictions, the Commission shall bring the issue to the attention of the committee referred to in Article 22 of Regulation (EU) No 1025/2012 and of the CPR Acquis Expert Group.7.A product subject to product requirements which is in conformity with voluntary harmonised standards or parts thereof, the references of which have been published in the Official Journal of the European Union, shall be presumed to be in conformity with the product requirements covered by those standards or parts thereof.8.The Commission is empowered to adopt delegated acts in accordance with Article 89 to amend Annex III in order to adapt it to technical progress and to cover new risks and environmental aspects and to comply with the priorities established in Article 4, based on the regulatory needs of the Member States.
Article 8Common specifications conferring a presumption of conformity1.The Commission may adopt implementing acts establishing common specifications that provide an alternative means to comply with the product requirements established in accordance with Article 7(1).Those implementing acts shall be adopted only where the following conditions are fulfilled:(a)the Commission has requested, pursuant to Article 7(3), one or more European standardisation organisations to draft a voluntary harmonised standard for the product requirements and:(i)the request has not been accepted; or(ii)the voluntary harmonised standard addressing that request is not delivered within the deadline set in accordance with Article 10(1) of Regulation (EU) No 1025/2012; or(iii)the voluntary harmonised standard does not comply with the request; and(b)no reference of voluntary harmonised standards covering the product requirements has been published in the Official Journal of the European Union in accordance with Regulation (EU) No 1025/2012 and no such reference is expected to be published within a reasonable period.Those implementing acts shall be adopted in accordance with the examination procedure referred to in Article 90(3).2.Before preparing a draft implementing act referred to in paragraph 1 of this Article, the Commission shall inform the committee referred to in Article 22 of Regulation (EU) No 1025/2012 that it considers that the conditions in paragraph 1 of this Article have been fulfilled.3.When preparing the draft implementing act referred to in paragraph 1 of this Article, the Commission shall take into account the views of the relevant bodies and of the CPR Acquis Expert Group and shall duly consult all relevant stakeholder organisations receiving Union financing under Regulation (EU) No 1025/2012.4.A product which is in conformity with the common specifications established by implementing acts referred to in paragraph 1 of this Article, or parts thereof, shall be presumed to be in conformity with the product requirements established by delegated acts referred to in Article 7(1) covered by those common specifications or parts thereof.5.The Commission shall repeal the implementing acts referred to in paragraph 1 of this Article, or parts thereof which cover the same product requirements as those covered by a voluntary harmonised standard the reference of which is published in the Official Journal of the European Union in accordance with Article 7(5) or (6).6.When a Member State or the European Parliament considers that a common specification does not entirely satisfy the product requirements established by delegated acts referred to in Article 7(1), it shall inform the Commission thereof, by submitting a detailed explanation. The Commission shall assess that detailed explanation and may, if appropriate, amend the implementing act establishing the common specification in question.
Article 9General product information, instructions for use and safety information1.General product information, instructions for use and safety information shall be provided in relation to construction products covered by a harmonised technical specification or a European technical assessment. The content of the general product information, instructions for use and safety information is set out in Annex IV.2.As part of the standardisation request referred to in Article 5(2), the Commission may also request the European standardisation organisation to issue guidelines, including technical details, necessary for drawing up general product information, instructions for use and safety information in accordance with Annex IV.3.If the Commission considers that the guidelines issued by the European standardisation organisation pursuant to paragraph 2 of this Article for a specific product family or product category do not ensure adequate and homogeneous implementation of paragraph 1 of this Article, the Commission is empowered to adopt delegated acts in accordance with Article 89 to supplement this Regulation by establishing rules on the provision of general product information, instructions for use and safety information for the respective product family or product category.4.The Commission is empowered to adopt delegated acts in accordance with Article 89 to amend Annex IV in order to adapt it to technical progress and new information needs.
Article 10Assessment and verification systems1.The assessment and verification of a product’s performance in relation to its essential characteristics, as set out in harmonised technical specifications adopted in accordance with Articles 5 and 6 or in European assessment documents referred to in Article 31, or of the product’s conformity with product requirements adopted in accordance with Article 7, shall be carried out in accordance with one or more of the systems set out in Annex IX.2.The Commission is empowered to adopt delegated acts in accordance with Article 89 to supplement this Regulation, by determining, for each product family or product category, the applicable assessment and verification system among those referred to in Annex IX. Those delegated acts may determine different assessment and verification systems within the same product family or product category, differentiating by essential characteristic or product requirement. The assessment and verification systems shall be determined before the harmonised technical specifications or European assessment documents become applicable.3.The delegated acts adopted in accordance with paragraph 2 shall take into account the intended uses, the potential damage resulting from product deficiencies, the product’s sensitivity to performance variations under production conditions, the likelihood of errors during its manufacturing and the possibility of easily detecting manufacturing errors. Those delegated acts shall be tailored to the respective product families or product categories and shall minimise the burden on manufacturers, whilst ensuring a high level of protection of health and safety of persons and of the environment.4.The Commission is empowered to adopt delegated acts in accordance with Article 89 in order to amend Annex IX to:(a)introduce additional assessment and verification systems when necessary to adapt to technical progress; or(b)amend the existing assessment and verification systems to counter systematic non-compliance by notified bodies or manufacturers and to harmonise the application of the requirements or obligations contained in them, without such amendments adding or removing any task defined in a system.When adopting delegated acts under point (a), the Commission may not introduce additional systems that set more demanding obligations for economic operators than those provided for in System 1+. In addition, the Commission may introduce such additional systems only when it is evident that guidance on the application of existing systems has proved to be insufficient.
Article 11Harmonised zone and national measures1.This Regulation, and the harmonised technical specifications adopted in accordance with it, together, establish a "harmonised zone".The harmonised zone covers all products subject to harmonised technical specifications.Harmonised technical specifications shall be presumed to be comprehensive, in the following respects:(a)laying down all essential characteristics and their assessment methods;(b)specifying all product requirements other than those covered by other Union law; and(c)determining the applicable assessment and verification systems.Harmonised technical specifications for new products shall apply to used products from third countries unless the harmonised technical specification explicitly provides rules for used products.2.Member States shall respect the harmonised zone in their national laws, regulations and administrative measures, and shall neither prohibit nor impede the making available on the market of products covered by it when those products are in compliance with this Regulation. Member States shall not lay down essential characteristics and their assessment methods or product requirements other than those set out in the harmonised technical specifications.The harmonised zone does not affect the right of Member States to specify national requirements for the use of products that are subject to harmonised technical specifications. Any assessment methods and systems for assessment and verification set out in such national requirements shall be in accordance with the applicable harmonised technical specifications.Member States shall ensure that the making available on the market of products within the harmonised zone which are in compliance with this Regulation shall not be impeded by rules or conditions imposed by public bodies or by private bodies acting as a public undertaking or private bodies acting as a public body on the basis of a monopoly position or under a public mandate.3.When complying with the obligations provided for in paragraph 2, Member States shall in particular apply the following rules:(a)no requirements for information or registration related to the placing on the market of the product other than those laid down in the harmonised zone shall be established;(b)no assessments of the product other than those set out in the harmonised zone shall be made mandatory;(c)no markings attesting to conformity with requirements or declared performances in relation to essential characteristics covered by the harmonised zone shall be required other than the CE marking, and any existing provisions in national measures requiring such markings shall be withdrawn;(d)national laws, regulations and administrative measures shall respect the threshold levels established in accordance with Article 5(5);(e)national laws, regulations and administrative measures shall not be based on classes, sub-classes or additional classes other than those established in accordance with Article 5;(f)national laws, regulations and administrative measures shall not require more assessments and verifications than those established in accordance with Article 10(1).4.Member States shall register in the Single Digital Gateway established by Regulation (EU) 2018/1724 of the European Parliament and of the CouncilRegulation (EU) 2018/1724 of the European Parliament and of the Council of 2 October 2018 establishing a single digital gateway to provide access to information, to procedures and to assistance and problem-solving services and amending Regulation (EU) No 1024/2012 (OJ L 295, 21.11.2018, p. 1). all their national laws, regulations and administrative measures related to construction products on their territory covered by the harmonised zone.5.Where a Member State deems it necessary on imperative grounds of health and safety of persons or protection of the environment and in order to address immediate regulatory needs, to take measures applicable to products within the harmonised zone in relation to characteristics not laid down in harmonised technical specifications, it shall notify the Commission thereof, justifying the need for the measures taken and explaining the regulatory need it aims to address.To that end, Member States shall use the procedure set up by Directive (EU) 2015/1535 of the European Parliament and of the CouncilDirective (EU) 2015/1535 of the European Parliament and of the Council of 9 September 2015 laying down a procedure for the provision of information in the field of technical regulations and of rules on Information Society services (OJ L 241, 17.9.2015, p. 1).. When doing so, Member States shall make reference to this paragraph and specify which elements are part of the measure.The Commission shall reply to the notification within the time limits established in the procedure set up by Directive (EU) 2015/1535. The Commission shall within six months of the notification either put forward a proposal for authorisation in accordance with paragraph 6 of this Article or communicate its grounds for rejecting the national measure.Upon receipt of a notification as referred to in the first subparagraph, the Commission shall, irrespective of whether it intends to authorise the measure, without delay submit the matter to the CPR Acquis Expert Group for consultations on whether updates to existing performance harmonised standards need to be requested as a priority.6.The Commission shall adopt an implementing act, authorising the national measure notified under paragraph 5 where:(a)the notified measure appears duly justified in the light of imperative grounds of health and safety of persons or protection of the environment, including the climate;(b)the regulatory need is not covered by harmonised technical specifications or by other Union law;(c)the notified measure does not discriminate against economic operators of other Member States;(d)the notified measure is able to cover the respective regulatory need;(e)the notified measure does not constitute a serious obstacle to the functioning of the internal market; and(f)the notified measure is not expected to be covered by a harmonised standard which is to be delivered within one year from the date of the notification referred to in paragraph 5 of this Article, following a standardisation request issued pursuant to Article 5(2), or, at the moment of that notification, no implementing act referred to in Article 6(1) has been presented to the committee referred to in Article 90(1).Those implementing acts shall be adopted in accordance with the examination procedure referred to in Article 90(3). They shall be withdrawn once the regulatory need is covered by harmonised technical specifications or by other Union law.On duly justified imperative grounds of urgency relating to health and safety of persons or the protection of the environment, the Commission shall adopt immediately applicable implementing acts in accordance with the procedure referred to in Article 90(4).7.This Regulation does not affect the possibility for Member States to introduce mandatory deposit-refund systems or to oblige manufacturers to accept to regain, directly or via their importers and distributors, ownership of their new, surplus or unsold non-custom-made products that are in a state equivalent to that in which they were placed on the market, provided that the measure does not directly or indirectly discriminate against economic operators in other Member States.8.This Regulation does not affect the possibility for Member States to ban the destruction of surplus or unsold products, or to make their destruction conditional upon their previously having been made available on a national brokering platform for non-commercial use of products.
Article 12Relationship with other Union law1.To avoid double assessment of the same aspects of health and safety of persons or protection of the environment in respect of products, the Commission is empowered to adopt delegated acts in accordance with Article 89 to supplement this Regulation by laying down the conditions under which obligations relating to the assessment of a product’s performance or the fulfilment of certain product requirements, including the equivalence of assessment and verification systems required under this Regulation and obligations as regards general product information, instructions for use and safety information requirements, can be satisfied by the fulfilment of obligations provided for under other Union law.The conditions referred to in the first subparagraph shall not allow for product safety levels which are less strict than those established in accordance with this Regulation.2.Where conflicts arise between this Regulation and Regulation (EU) 2024/1781 as well as Regulation (EU) No 1025/2012, the relevant provisions of this Regulation shall prevail.
CHAPTER IIPROCEDURE, DECLARATIONS AND MARKINGS
Article 13Declaration of performance and conformity1.Where a product is covered by a harmonised technical specification adopted in accordance with Articles 5 or 6, the manufacturer shall undergo the applicable assessment and verification system set out in Annex IX and draw up a declaration of performance and conformity before such a product is placed on the market. Where a product is covered by a harmonised technical specification adopted in accordance with Article 7, the manufacturer shall also verify the product’s compliance with applicable product requirements that have been specified by delegated acts. The manufacturer of a product which is not covered by any harmonised technical specification may issue a declaration of performance and conformity in accordance with the relevant European assessment document and European technical assessment.2.By drawing up the declaration of performance and conformity, the manufacturer assumes responsibility for the conformity of the product with its declared performance and any applicable product requirements, and becomes liable in accordance with Union and national laws on contractual and extra-contractual liability. In the absence of objective indications to the contrary, Member States shall presume the declaration of performance and conformity drawn up by the manufacturer to be accurate and reliable.In the event of non-compliance, or in the absence of a declaration of performance and conformity when such a declaration is required, the product may not be made available on the market.
Article 14Exemptions from drawing up a declaration of performance and conformityBy way of derogation from Article 13(1), a manufacturer may decide not to undergo the applicable assessment and verification of the product’s compliance with applicable product requirements and not to draw up a declaration of performance and conformity when any of the following applies:(a)the product is individually manufactured or custom-made and fulfils all of the following conditions:(i)it is manufactured using a non-series process;(ii)it is produced in response to a specific order;(iii)it is installed in a single identified construction work by a manufacturer who is also responsible for the safe incorporation of the product into the construction work; and(iv)it is in compliance with the applicable national rules, and under the supervision of those responsible for the safe execution of the construction works designated under the applicable national rules;(b)the product is manufactured in a manner exclusively appropriate to heritage conservation and in a non-series process for adequately renovating construction works officially protected as part of a designated environment or because of their special architectural or historic merit, in compliance with the applicable national rules.
Article 15Content of the declaration of performance and conformity1.The declaration of performance and conformity shall be drawn up using the model set out in Annex V. The declaration of performance and conformity shall express the performance of products in relation to the essential characteristics of those products in accordance with the relevant harmonised technical specifications or European assessment document.Where product requirements specified in accordance with Article 7 are applicable, the declaration of performance and conformity shall state that the fulfilment of those requirements has been demonstrated.2.The declaration of performance and conformity shall include the product’s environmental sustainability performance over its life cycle in respect of the predetermined environmental essential characteristics listed in Annex II for those characteristics that are declared. The performance shall include the packaging used or most likely to be used and shall be calculated using the latest version of software made available free of charge on the website of the Commission.Updates of the software referred to in the first subparagraph shall become mandatory for the purposes of this Regulation one year after their publication. Such software updates may be voluntarily applied from their date of publication.3.The declaration of performance and conformity shall cover at least a product’s performance over its life cycle with regard to the following essential characteristics:(a)essential characteristics listed in points (a) to (d) of Annex II, from 8 January 2026;(b)essential characteristics listed in points (e) to (m), of Annex II, from 9 January 2030;(c)essential characteristics listed in points (n) to (s), of Annex II, from 9 January 2032.The declaration of performance and conformity shall also cover those essential characteristics which always have to be declared, as determined in delegated acts adopted in accordance with Article 5(5).4.No marking other than the CE marking may be placed on the declaration of performance and conformity.5.The Commission is empowered to adopt delegated acts in accordance with Article 89 to amend the model set out in Annex V to adapt it to reflect technical progress as regards new information needs, to facilitate the fulfilment of digital product passport requirements set out in Articles 76 and 77, and to ensure interoperability and correct integration with the construction digital product passport system in accordance with Article 75.6.The information referred to in Article 31 or, as the case may be, in Article 33 of Regulation (EC) No 1907/2006 of the European Parliament and of the CouncilRegulation (EC) No 1907/2006 of the European Parliament and of the Council of 18 December 2006 concerning the Registration, Evaluation, Authorisation and Restriction of Chemicals (REACH), establishing a European Chemicals Agency, amending Directive 1999/45/EC and repealing Council Regulation (EEC) No 793/93 and Commission Regulation (EC) No 1488/94 as well as Council Directive 76/769/EEC and Commission Directives 91/155/EEC, 93/67/EEC, 93/105/EC and 2000/21/EC (OJ L 396, 30.12.2006, p. 1). shall be provided together with the declaration of performance and conformity.
Article 16Supply of the declaration of performance and conformity1.The manufacturer shall supply by electronic means a copy of the declaration of performance and conformity of each product which is made available on the market, unless the declaration is included in a digital product passport that fulfils the conditions set out in Article 76 and is available through the construction digital product passport system established in accordance with Article 75.However, where a batch of the same product is supplied to a single user, it may be accompanied by a single copy of the declaration of performance and conformity.2.By way of derogation from paragraph 1 of this Article, a manufacturer may make the declaration of performance and conformity referred to in Article 13(1) available on a website, provided that the manufacturer complies with all of the following conditions:(a)ensures that the content of the declaration of performance and conformity is made available in an unamendable electronic format on the website;(b)provides the declaration of performance and conformity in a human- and machine-readable format and offers the possibility to download a copy in a commonly readable format;(c)ensures that the website where the declaration of performance and conformity has been made available is monitored and maintained so that the website and the declarations of performance and conformity are continuously available to recipients of the construction product;(d)ensures that the recipients of construction products are able to access the declaration of performance and conformity free of charge;(e)provides instructions to the recipients of construction products on how to access the website and the declarations of performance and conformity drawn up for such products available on that website;(f)provides a link between the product and the declaration of performance and conformity related to it through the unique identification code of the product type; manufacturers may use a data carrier, including a permalink, to provide the link, provided that point (a) is complied with.3.As part of the standardisation request referred to in Article 5(2), the Commission may also request the European standardisation organisation to issue guidelines to ensure interoperability of the human- and machine readable formats referred to in paragraph 2, point (b) of this Article.4.The manufacturer shall supply or make available in a digital product passport in accordance with paragraph 1, or on a website in accordance with paragraph 2, the declaration of performance and conformity in the language or languages required by each of the Member States in which the manufacturer intends to make the product available. Another economic operator who makes that manufacturer’s product available in any additional Member State shall make a translation or translations of the declaration of performance and conformity available in the languages required by the additional Member State, together with the respective original version.
Article 17General principles and use of CE marking1.The CE marking shall be subject to the general principles set out in Article 30 of Regulation (EC) No 765/2008.2.The CE marking shall be affixed only to those products for which the manufacturer has drawn up a declaration of performance and conformity in accordance with Articles 13 and 15. The CE marking shall be affixed to key parts.3.By affixing the CE marking to the product, or having it affixed, the economic operator indicates that it has assumed responsibility for the conformity of the product with the declared performance and applicable product requirements laid down in accordance with this Regulation. By affixing the CE marking, the economic operator becomes liable for the declared performance and the fulfilment of those requirements in accordance with national law on contractual and extra-contractual liability.4.The CE marking shall be the only marking attesting to the performance of the product with regard to assessed essential characteristics in accordance with this Regulation, as well as to the conformity of the product with this Regulation.
Article 18Rules and conditions for the affixing of CE marking1.The CE marking shall be affixed visibly, legibly and indelibly to the product. Where this is not possible or not warranted on account of the nature of the product, the CE marking shall be affixed to a label attached to the product or to the packaging or, where that is also not possible, to the accompanying documents.2.The CE marking shall be followed by:(a)the last two digits of the year in which the CE marking was first affixed; or, in the case of used products, the last two digits of the year when the product was deinstalled followed by the last two digits of the year in which the CE marking was affixed to the used product;(b)the name and the registered address, or the identifying mark allowing easy and unambiguous identification of the name and address, of the manufacturer;(c)the name and the registered address of the authorised representative, or the identifying mark allowing easy and unambiguous identification of the name and address of the authorised representative where the manufacturer does not have a place of business in the Union or where the manufacturer chooses to have an authorised representative;(d)the unique identification code of the product-type;(e)the declaration code of the declaration of performance and conformity;(f)the identification number of the notified body or bodies verifying the product type and assessing the factory production control, if applicable; and(g)a data carrier connected to the digital product passport referred to in Article 76 if such a digital product passport is available through the construction digital product passport system established pursuant to Article 75.The information listed in points (d) and (e) of the first subparagraph of this paragraph may be replaced by a data carrier, including permalink connected to the declaration of performance and conformity pursuant to Article 16(2), point (e), if the declaration of performance and conformity is available on a website. The information listed in points (d) and (e) of the first subparagraph of this paragraph may be omitted if a data carrier referred to in point (g) of the first subparagraph of this paragraph is provided.3.The CE marking shall be affixed before the product is placed on the market. It may be followed by a pictogram or any other mark indicating a special risk or use.
Article 19Other markings and performance claims1.Markings other than the CE marking, including private ones, may be affixed to a product only if they do not indicate that the product’s performance in relation to essential characteristics covered by applicable harmonised technical specifications had to be assessed in a way different from that laid down by this Regulation.Officially recognised EN ISO 14024 type I ecolabels may be affixed to a product if they fulfil the requirement in the first subparagraph.2.Markings allowed in accordance with paragraph 1 and other markings set out by Union legislation may be affixed to a product provided that they do not impair the visibility, legibility and meaning of the CE marking.3.Where a product is covered by a harmonised technical specification, a claim made by an economic operator about the product’s performance, which concerns an essential characteristic covered by that harmonised technical specification, shall comply with the assessment method for that particular essential characteristic as laid down in the harmonised technical specifications.4.Where a product is covered by harmonised technical specifications, claims about its performance in relation to the essential characteristics laid down in those harmonised technical specifications may be additionally provided in a place other than in the declaration of performance and conformity only if they are already provided in the declaration of performance and conformity.The first subparagraph shall not apply to situations where, in accordance with Article 14, no declaration of performance and conformity has been drawn up.
CHAPTER IIIOBLIGATIONS AND RIGHTS OF ECONOMIC OPERATORS
Article 20Obligations of all economic operators1.The obligations of economic operators under this Chapter are applicable only in relation to products covered by a harmonised technical specification, or to products that have been CE-marked on the basis of a European technical assessment.2.An economic operator shall take all necessary measures to ensure continued compliance with this Regulation. Where non-compliance of the economic operator or of a product has been stated and corrective action has been requested by a market surveillance authority in accordance with Article 65(1), the economic operator shall submit progress reports to that authority until that authority decides that the corrective action can be closed.3.An economic operator shall, on request of a competent national authority, identify to that authority any economic operator or other actor:(a)who has supplied that economic operator with a product, including components or spare parts of products, and the quantity of that supply, or who has supplied it with a service covered by this Regulation;(b)to whom that economic operator has supplied a product, including components or spare parts of products, and the quantity of that supply, or to whom it has supplied a service covered by this Regulation.When identifying the economic operators or other actors referred to in the first subparagraph, an economic operator shall inform the competent national authority of, at least, the following:(a)the contact details, including addresses and email addresses of those economic operators or actors;(b)the tax and company registration numbers of those economic operators or actors.4.An economic operator shall keep all documents and all information referred to in this Chapter at the disposal of competent national authorities for a period of 10 years after the economic operator supplied or was supplied with the product or service in question, unless the documents or the information have been made available through the digital product passport referred to in Article 76. An economic operator shall present the documentation and information within 10 days of receipt of a request by a competent national authority.5.An economic operator may register itself in its respective national system established in accordance with Article 71(5).An economic operator shall make available to consumers and users communication channels, including telephone numbers, email addresses or dedicated sections of its website, allowing them to communicate any accident, other incident or safety issue they have experienced with the product.6.Where an economic operator considers that a non-conforming product presents a risk to health and safety of persons or to the environment, it shall immediately inform thereof the competent national authorities of the Member States in which it made the product available, giving details, in particular, of the non-compliance and of any corrective measures taken. An economic operator may inform the competent national authorities of any other likely infringement of this Regulation of which it becomes aware, of the non-compliance and of any corrective measures taken.7.An economic operator shall be liable for infringements of this Article or of the Articles in this Chapter related to its activities, in accordance with national law on contractual and extra-contractual liability.
Article 21Rights of manufacturers1.A manufacturer shall have the right to request from its suppliers and service providers the information necessary in relation to their products to fulfil its obligations under this Regulation.2.If the manufacturer is subject to third-party tasks carried out by a notified body, the manufacturer shall have the right to request from its suppliers or service providers that they permit that notified body to have access to their documentation and to their premises to the extent that the notified body requires such access in order to carry out its tasks.3.The rights established in paragraph 1 also apply to a manufacturer placing a used or remanufactured product on the market in relation to the supplier of the used product, including the deinstaller where applicable. The information required may include, but is not limited to, information about the previous use of the product and about the process of deinstalling it.4.A manufacturer shall have the right to request from its suppliers and service providers the data and calculations required under Article 15(2) in relation to the supplies or services provided, including the necessary validation reports issued by a notified body.
Article 22Obligations of manufacturers1.When placing a product on the market, the manufacturer shall determine the product type, respecting the boundaries set up therefor by the definition provided in Article 3, point (27). The manufacturer shall ensure that the product’s performance is assessed in relation to both mandatory essential characteristics and those essential characteristics intended to be declared. If the product is covered by product requirements established by delegated acts referred to in Article 7(1), the manufacturer shall ensure that the product has also been designed and constructed in accordance with those requirements.A natural or legal person that manufactures a product using 3-D printing shall satisfy the obligations incumbent on manufacturers when placing it on the market. The obligations shall include, but are not limited to, the use of appropriate 3-D datasets, the use of materials compliant with the applicable procedures under this Regulation, and the verification of the compatibility of 3-D datasets, printing material and the printing technology used.2.Where a product’s compliance with applicable requirements and its performance in relation to essential characteristics referred to in paragraph 1 of this Article have been demonstrated in accordance with the applicable assessment and verification system or systems set out in Annex IX, the manufacturer shall draw up a declaration of performance and conformity in accordance with Articles 13 to 15, affix the CE marking in accordance with Articles 17 and 18 and, when applicable, ensure the availability of spare parts not commonly available in the market, as referred to in paragraph 8 of this Article, and affix the labelling pursuant to paragraph 9 of this Article.3.The manufacturer shall, as the basis for the declaration of performance and conformity, draw up a technical documentation in which he shall indicate:(a)the declared use, which shall fall within the scope of the applicable intended use;(b)all the relevant elements necessary to demonstrate performance and conformity;(c)information on the procedures in place referred to in paragraph 4 of this Article;(d)information on the applicable system or systems set out in Annex IX;(e)where relevant, information on the application of simplified procedures applied in accordance with Articles 59 to 61; and(f)the calculation of the performance of environmental sustainability in respect of essential characteristics as referred to in Article 15(2).4.The manufacturer shall ensure that procedures are in place to ensure that products fulfil their declared performance and remain in conformity with this Regulation. Product design, including 3-D datasets, production processes and material used shall be appropriate. Where the product is manufactured in series production, the manufacturer shall ensure that procedures are in place to ensure that it maintains its declared performance and remains in conformity with this Regulation. Changes in the product design, including 3-D datasets, production process and material used shall be appropriate. Changes in the applicable harmonised technical specifications shall be adequately taken into account and, where the performance or conformity of the product is affected, shall trigger a re-assessment in accordance with the relevant assessment procedure.The manufacturer shall, where deemed appropriate with regard to ensuring the accuracy, reliability and stability of the declared performance and of the conformity of a product, carry out sample testing of products placed or made available on the market, investigate, and, if necessary, keep a register of complaints, of non-conforming products and product recalls, and shall keep importers and distributors informed thereof.5.The manufacturer shall ensure that its products bear a manufacturer-specific unique identification code of the product type and, where available, a batch or serial number which is easily visible and legible for users. Where that is not possible on account of the nature of the product, the required information shall be provided on an affixed label, on the packaging or, where that is also not possible, in a document accompanying the product.The manufacturer shall, in the same way as set out in the first subparagraph, label a product as "Only for professional use" if expertise is needed in order to use it and shall display the label to customers before they are bound by a sales contract, including in the case of distance selling. Products not labelled "Only for professional use" shall be deemed to also be intended for non-professional users and consumers within the meaning of this Regulation and of Regulation (EU) 2023/988.The manufacturer shall display to customers, in a visible manner, before they are bound by a sales contract, including in the case of distance selling, the information which must be provided pursuant to this Regulation.6.When making a product available on the market, the manufacturer shall ensure that it is accompanied by general product information, instructions for use and safety information, as set out in Annex IV in a language to be determined by the Member State concerned or, in absence of such determination, in a language which can be easily understood by users.7.By 18 months after the entry into force of the delegated act referred to in Article 75(1) the manufacturer shall make available a digital product passport referred to in Article 76, through the construction digital product passport system referred to in Article 75, connected to a data carrier referred to in Article 18(2), point (g).8.In order to ensure the availability of spare parts not commonly available on the market, the Commission is empowered to adopt delegated acts in accordance with Article 89 to supplement this Regulation, by imposing in respect of certain product families and product categories an obligation on manufacturers to make available on the market specific spare parts not commonly available for the products they place on the market.The obligation established by the delegated acts referred to in the first subparagraph of this paragraph shall apply for a period of 10 years after the last product of the respective type has been placed on the market, unless the delegated act sets a different period.Manufacturers subject to the obligation laid down in the first paragraph shall offer the spare parts within a reasonably short delivery period, at a reasonable and non-discriminatory price, and shall inform the public thereof.9.In order to ensure transparency for users and to promote sustainable products, the Commission is empowered to adopt delegated acts in accordance with Article 89 to supplement this Regulation, by establishing specific environmental sustainability labelling requirements for particular product families and product categories when the following conditions are fulfilled:(a)the product is typically chosen or purchased by consumers; and(b)the product does not have a significantly different overall environmental performance over its life cycle depending on its installation.The labelling shall be based on the performance of the product, as assessed in accordance with Article 5(1) or Article 6(1), and shall provide consumer-friendly information understandable by non-experts.10.The delegated acts referred to in paragraph 9 shall determine the way in which the manufacturer is to affix the label, by specifying the following:(a)the content of the label;(b)the layout of the label, taking into account its visibility and legibility;(c)the manner in which the label is to be displayed to customers, including in the case of distance selling;(d)where appropriate, the electronic means to be used for generating labels.11.A manufacturer who considers or has reason to believe that a product which it has placed on the market does not conform to its declared performance or does not comply with this Regulation shall immediately take the necessary corrective measures to bring that product into conformity or compliance, or, if appropriate, to withdraw or recall it. If the issue is linked to a supplied component or an externally provided service, the manufacturer shall inform the supplier or service provider and the manufacturer’s competent national authority.12.Where the product presents a risk, the manufacturer shall, without undue delay and at the latest within three working days, inform all the authorised representatives, importers, distributors, fulfilment service providers, and online market places involved in its distribution, as well as the competent national authorities of the Member States in which the manufacturer or, to its knowledge, other economic operators made the product available. The manufacturer shall, to that effect, provide all useful details and, in particular, specify the type of the non-compliance, the frequency of accidents or incidents, and the corrective measures taken or recommended. In the case of risks caused by products which have already reached an end user or consumer who cannot be identified or contacted directly, the manufacturer shall, through the media and other appropriate channels, ensuring the widest possible reach, disseminate information about appropriate measures to eliminate or, if not possible, to reduce the risks. Where there is a serious risk the manufacturer shall withdraw and recall the product at its own cost.
Article 23Obligations of authorised representatives1.A manufacturer established in the Union may appoint, by a written mandate, any natural or legal person established within the Union as a single authorised representative. A manufacturer not established in the Union shall appoint a single authorised representative.The drawing up of technical documentation shall not form part of the authorised representative’s mandate.2.The authorised representative shall perform the tasks specified in the mandate received from the manufacturer. The mandate shall allow the authorised representative to do at least the following:(a)keep the declaration of performance and conformity and the technical documentation at the disposal of competent national authorities;(b)further to a reasoned request from a competent national authority, provide that authority with all the information and documentation necessary to demonstrate the conformity of a product with its declared performance and its compliance with other applicable requirements in this Regulation;(c)terminate the contract if the manufacturer has acted contrary to its obligations under this Regulation and inform the manufacturer, the competent national authorities of the Member States where the product is placed on the market and the competent national authority of his own place of business thereof;(d)when there is reason to believe that a product is non-compliant or presents a risk, inform the manufacturer and the competent national authorities of the Member States where the product is placed on the market and the competent national authority of the authorised representative thereof; and(e)cooperate with the competent national authorities, at their request, in any action taken to eliminate risks posed by, and to remedy non-conformities of, products covered by the mandate of the authorised representative.3.The authorised representative shall verify at documentary level that:(a)the product bears the CE marking, and the labelling in accordance with Article 22(9);(b)the product is accompanied by a declaration of performance and conformity, or that declaration is available in accordance with Article 16(1) or (2); and(c)the manufacturer has complied with the requirements set out in Article 22(5), (6) and (7).4.Where an authorised representative identifies a case of non-compliance mentioned in paragraph 3 of this Article, it shall ask the manufacturer to act in accordance with Article 22(11) and (12).
Article 24Obligations of importers1.Importers shall place on the market only products which are compliant with this Regulation.2.Before placing a product on the market, the importer shall ensure that the product’s compliance with applicable requirements and its performance in relation to relevant essential characteristics have been demonstrated by the manufacturer in accordance with Article 22(1) and (2).The importer shall ensure that:(a)the manufacturer has drawn up the technical documentation referred to in Article 22(3);(b)the product bears the CE marking, and the labelling in accordance with Article 22(9);(c)the product is accompanied by the declaration of performance and conformity or that the declaration is available in accordance with Article 16(1) or (2); and(d)the manufacturer has complied with the requirements set out in Article 22(5), (6) and (7).3.The importer shall verify that the use of the product has been declared by the manufacturer, and shall ensure that the product is accompanied by general product information, instructions for use and safety information as set out in Annex IV in a language determined by the Member State concerned or, in absence of such determination, in a language which can be easily understood by users. The importer shall display to customers, in a visible manner, before they are bound by a sales contract, including in the case of distance selling, the information which must be provided pursuant to this Regulation or harmonised technical specifications.4.The importer shall ensure that, while a product is under its responsibility, the conditions of its storage or transport do not jeopardise its conformity with the declaration of performance and conformity, or its compliance with other applicable requirements in this Regulation.5.Where an importer considers, or has reason to believe, that a product is not in conformity with the declaration of performance and conformity, or not in compliance with other applicable requirements in this Regulation, the importer shall not place the product on the market until it conforms to the accompanying declaration of performance and conformity and it complies with the other applicable requirements of this Regulation, or until the declaration of performance and conformity is corrected. Furthermore, where the product presents a risk, the importer shall inform the manufacturer and the responsible competent national authority thereof.6.The importer shall indicate its name, registered trade name or registered trade mark, its place of business, its contact address and, where available, electronic means of communication, either on the product or, where that is not possible, on its packaging, or in a document accompanying the product.7.The importer shall investigate complaints, and, if necessary, keep a register of complaints, of non-conforming products and of product withdrawals or recalls, and shall keep manufacturers and distributors informed of any such monitoring.8.Importers who consider or have reason to believe that a product, which they have placed on the market, is not in conformity with its declared performance or not in compliance with other applicable requirements in this Regulation, shall immediately take the necessary corrective measures to bring that product into conformity, or, if appropriate, to withdraw or recall it. Furthermore, where the product poses a risk, importers shall immediately inform the competent national authorities of the Member States in which they made the product available on the market to that effect, giving details, in particular, of the non-conformity and of any corrective measures taken.9.Importers selling to end users shall also fulfil the obligations incumbent on distributors.
Article 25Obligations of distributors1.When making products available on the market, distributors shall act with due care in relation to the obligations of this Regulation.2.Before making a product available on the market, the distributor shall verify that:(a)the product bears the CE marking, and the labelling in accordance with Article 22(9), where required;(b)the product is accompanied, where required, by a declaration of performance and conformity, or that the declaration is available in accordance with Article 16(2);(c)the product is accompanied by general product information, instructions for use and safety information in accordance with Article 22(6), in a language which can be easily understood by end users in the Member State in which the product is to be made available on the market;(d)the manufacturer and the importer have complied with the requirements set out in Article 22(5) and (7) and Article 24(6) respectively.3.The distributor shall display to customers, in a visible manner, before they are bound by a sales contract, including in the case of distance selling, the information which must be provided pursuant to this Regulation.4.Where a distributor considers or has reason to believe that a product is not in conformity with its declared performance or not in compliance with other applicable requirements in this Regulation, the distributor shall not make the product available on the market until it conforms to its accompanying declaration of performance and conformity and it complies with the other applicable requirements in this Regulation. Furthermore, where the product presents a risk, the distributor shall inform the manufacturer and the responsible competent national authorities thereof.5.The distributor shall ensure that, while a product is under its responsibility, storage or transport conditions do not jeopardise the product’s conformity with its declared performance or its compliance with other applicable requirements in this Regulation.6.A distributor who considers or has reason to believe that a product, which it has made available on the market, is not in conformity with its declared performance or not in compliance with other applicable requirements in this Regulation shall make sure that the necessary corrective measures to bring that product into conformity or, if appropriate, to withdraw or to recall it, are taken. Furthermore, where the product poses a risk, the distributor shall immediately inform the competent national authorities of the Member States in which it has made the product available on the market to that effect, giving details, in particular, of the non-conformity and of any corrective measures taken.
Article 26Cases in which obligations of manufacturers apply to importers and distributors1.An importer or distributor shall be considered a manufacturer for the purposes of this Regulation and shall be subject to the obligations of a manufacturer pursuant to Article 22, where:(a)it places a product on the market under its own name or trademark;(b)it modifies a product intentionally or the product is unintentionally modified in such a way that compliance with the declaration of performance and conformity, or with the requirements set out in or adopted in accordance with this Regulation may be affected;(c)it makes a product available on the market with a declared use that is different from the declared use attributed by the manufacturer in the process of assessment and verification;(d)it claims for the product characteristics deviating from the characteristics declared by the manufacturer; or(e)it opts to assume the role of the manufacturer.2.Paragraph 1 shall also apply to an economic operator who places on the market:(a)a used product covered by a harmonised technical specification laying down provisions for used products;(b)a used product not covered by a harmonised technical specification with provisions for used products and not placed on the Union market before;(c)a remanufactured product.3.Paragraph 1 shall not apply where the economic operator only:(a)adds translations of information supplied by the manufacturer;(b)replaces the outer packaging of a product already placed on the market, including when changing the packaging size, if the repackaging is carried out in such a way that the original condition of the product cannot be affected by it, and that any information required by this Regulation is still correctly provided.4.An economic operator providing the activities listed in paragraph 3 shall inform thereof the manufacturer or its authorised representative, regardless of whether that economic operator owns the products or provides services. It shall carry out the repackaging in such a way that neither the original condition of the product nor its compliance with this Regulation is affected by the repackaging, and such that any information required by this Regulation is still correctly provided. The economic operator shall act with due care in relation to the obligations of this Regulation.
Article 27Obligations of fulfilment service providers1.When contributing to the making available on the market of a product, fulfilment service providers shall act with due care in relation to the obligations of this Regulation.2.A fulfilment service provider shall make sure that the labelling and documents provided by the manufacturer or importer are available or accompany the product, and in particular:(a)the CE marking and the labelling referred to in Article 22(9);(b)the declaration of performance and conformity;(c)the general product information and the instructions for use and safety information referred to in Article 22(6).3.A fulfilment service provider shall ensure that the conditions during warehousing, packaging, addressing or dispatching do not jeopardise a product’s conformity with its declared performance or its compliance with other applicable requirements in this Regulation. Manufacturers or importers of construction products shall provide their fulfilment service providers with the detailed information necessary for ensuring the safe storage, packaging, addressing or dispatch, and the further functioning of the product.4.Fulfilment service providers shall support product withdrawals or recalls, regardless of whether initiated by market surveillance authorities, manufacturers, authorised representatives or importers.5.Where a fulfilment service provider considers or has reason to believe that a product is not in conformity with the declaration of performance and conformity or not in compliance with other applicable requirements in this Regulation, it shall not support the making available of the product on the market until the product conforms to the relevant declaration of performance and conformity, and it complies with the other applicable requirements in this Regulation, or until the declaration of performance and conformity is corrected. Furthermore, where the product presents a risk, the fulfilment service provider shall inform the manufacturer and the responsible competent national authority thereof.
Article 28Obligations of online marketplaces1.An online marketplace shall:(a)for the purpose of complying with Article 31(1) of Regulation (EU) 2022/2065 of the European Parliament and of the CouncilRegulation (EU) 2022/2065 of the European Parliament and of the Council of 19 October 2022 on a Single Market For Digital Services and amending Directive 2000/31/EC (Digital Services Act) (OJ L 277, 27.10.2022, p. 1)., design and organise its online interface in such a way that allows economic operators to fulfil their obligations under Article 29(2) of this Regulation;(b)establish a single contact point for direct communication with Member States’ competent national authorities in relation to compliance with this Regulation, which can be the same as the contact point referred to in Article 22(1) of Regulation (EU) 2023/988 or Article 11(1) of Regulation (EU) 2022/2065;(c)give an appropriate answer to notices related to the notification of accidents and other incidents involving products received in accordance with Article 16 of Regulation (EU) 2022/2065;(d)cooperate to ensure effective market surveillance measures, including by abstaining from putting in place obstacles to such measures;(e)inform the competent national authorities of any action taken with regard to the non-compliance or suspected non-compliance of products covered by this Regulation;(f)establish a regular and structured exchange of information regarding content that has been removed by online marketplaces at the request of competent national authorities;2.As far as powers conferred by Member States in accordance to Article 14 of Regulation (EU) 2019/1020 are concerned, Member States shall confer on their market surveillance authorities the power, in respect of all products covered by this Regulation, to order an online marketplace to remove from its online interface specific illegal content referring to a non-compliant product, to disable access to it, or to display an explicit warning to end users when they access it. Such orders shall comply with Article 9 of Regulation (EU) 2022/2065.3.An online marketplace shall take the necessary measures to receive and process in accordance with Article 9 of Regulation (EU) 2022/2065 the orders referred to in paragraph 2 of this Article.4.This Article shall also apply to manufacturers, importers, or distributors offering products online without the involvement of an online marketplace.
Article 29Online and other distance sales1.Products offered for sale online or through other means of distance sales shall be deemed to be made available on the market if the offer is targeted at customers in the Union. An offer for sale shall be considered to be targeted at customers in the Union if the relevant economic operator directs, by any means, its activities to a Member State. An offer shall, inter alia, be considered to be targeted at customers in the Union where:(a)the economic operator uses the currency of a Member State;(b)the economic operator has used an internet domain name registered in one of the Member States, or uses an internet domain that refers to the Union or to one of the Member States; or(c)the geographical areas to which dispatch is available include a Member State.The conditions listed in the first subparagraph shall not apply if the economic operator explicitly and effectively excludes the Union market.2.Where an economic operator makes a product available on the market online or through other means of distance selling, the offer of that product shall, where required, clearly and visibly indicate the CE marking, the information listed in Article 18(2), the label pursuant to Article 22(9) and a data carrier connected to a digital product passport in accordance with Article 22(7).3.Any natural or legal person providing an intermediary service for the placing on the market of products shall fulfil the obligations of an economic operator pursuant to paragraph 2 in relation to the services provided.
Article 30Implementing acts regarding the obligations and rights of economic operatorsWhere it is necessary, to ensure the harmonised application of this Regulation, and only to the extent necessary to prevent diverging practices fragmenting the internal market for economic operators, the Commission may adopt implementing acts providing details on how economic operators are to fulfil the obligations and exercise the rights set out in this Chapter.Those implementing acts shall be adopted in accordance with the examination procedure referred to in Article 90(3).
CHAPTER IVEUROPEAN ASSESSMENT DOCUMENTS
Article 31European assessment documents1.The methods and criteria for assessing the performance of products, including used products, in relation to their essential characteristics may be laid down in European assessment documents provided that the products are not covered by:(a)a harmonised standard made mandatory by an implementing act referred to in Article 5(8);(b)an implementing act referred to in Article 6(1); or(c)a harmonised standard to be delivered in a period shorter than one year, in accordance with a standardisation request referred to in Article 5(2).2.A product shall not be considered to be covered by harmonised standards or implementing acts referred to in paragraph 1 where:(a)the declared use of the product falls outside of the scope of the intended use set out in the harmonised standard or implementing act;(b)the materials used are not identical to the materials to be used in accordance with the harmonised standard or implementing act; or(c)the assessment method set out in the harmonised standard or implementing act is not appropriate for that product.3.Following a request for a European technical assessment by a manufacturer, a group of manufacturers or a manufacturers’ association, or on the initiative of the Commission, the organisation of TABs may, in agreement with the Commission, draw up and adopt a European assessment document.The basic requirements for construction works set out in Annex I and the list of predetermined environmental essential characteristics set out in Annex II shall constitute the basis for the preparation of European assessment documents. The development and adoption of a European assessment document shall follow the principles and the procedure set out in Article 32.4.European assessment documents shall not be drawn up in relation to an essential characteristic of, or assessment method for, a product when there is another European assessment document covering the same essential characteristic or assessment method in relation to that specific product, the reference of which has either already been published in the Official Journal of the European Union, or which has been submitted to the Commission for assessment in accordance with Article 34(1).5.The organisation of TABs and the Commission may merge or reject requests for the development of a European assessment document in accordance with point 5 of Annex VI.6.From the date of mandatory application of a harmonised technical specification adopted in accordance with Article 5(8) or Article 6(1), covering the same product and the same intended use as a European assessment document, the European assessment document shall no longer be used for the purposes of this Regulation. In that case the Commission shall withdraw the reference of the European assessment document from the Official Journal of the European Union.7.European assessment documents shall constitute the basis for European technical assessments set out in Article 37.
Article 32Principles and procedure for the development and adoption of European assessment documents1.When developing and adopting European assessment documents, individual TABs and the organisation of TABs shall follow the procedure set out in Annex VI.2.When developing and adopting European assessment documents, individual TABs and the organisation of TABs shall:(a)be transparent to Member States, the manufacturer concerned and to other manufacturers or stakeholders that request to be informed;(b)disclose confidential information to the Commission only when necessary to assess the compliance of a European assessment document with regulatory provisions and protect commercial secrecy and confidentiality;(c)specify appropriate mandatory time limits in order to avoid unjustified delay;(d)allow for adequate participation by the Member States and the Commission;(e)be cost-effective for the manufacturer; and(f)ensure sufficient collegiality and coordination amongst TABs designated for the product in question.The balancing of requirements laid down in points (a) and (b) of the first subparagraph shall allow at least for the disclosure of the name of the product at the stage of the approval and the communication of the work programme, as set out in point 3 of Annex VI, and for the disclosure of the detailed contents of the draft European assessment document set out in point 8 of Annex VI.3.The TABs shall, together with the organisation of TABs, bear the full costs of the development and adoption of European assessment documents, unless such development is initiated by the Commission.4.TABs and the organisation of TABs shall avoid the proliferation of European assessment documents where there is no technical justification for differentiating between products. They shall, in particular, give preference to extending the scope of existing European assessment documents over creating new European assessment documents.5.The Commission is empowered to adopt, after consultations with the organisation of TABs, delegated acts in accordance with Article 89 to amend Annex VI in order to add additional procedural rules for the development and adoption of European assessment documents, where it is necessary to ensure the good functioning of the system of European assessment documents.
Article 33Obligations of the TAB receiving a request for a European technical assessment1.When receiving a request for a European technical assessment from a manufacturer, a group of manufacturers or a manufacturers’ association, the TAB shall comply with the following requirements:(a)where the product is covered by a harmonised technical specification or a European assessment document cannot be drawn up in accordance with Article 31, the TAB shall inform the applicant that a European technical assessment cannot be issued;(b)where the product is fully covered by a European assessment document the reference of which has been published in the Official Journal of the European Union, the TAB shall inform the applicant that the referenced European assessment document will be used as the basis for the European technical assessment to be issued;(c)where the product is eligible for a European assessment document referred to in Article 31, and no such document is in the process of being developed, the TAB shall inform the applicant that the procedures set out in Annex VI will be initiated.In the cases referred to in point (c) of the first subparagraph of this Article, but where a harmonised standard covering the same product is expected to be delivered in a period longer than one year as established in a standardisation request referred to in Article 5(2), the TAB shall inform the applicant about the possibility of a European assessment document no longer being used pursuant to Article 31(6).2.In the cases referred to in paragraph 1, first subparagraph, points (b) and (c) of this Article, the TAB shall inform the organisation of TABs and the Commission of the content of the request and of the reference to a relevant delegated act determining the assessment and verification system referred to in Article 10(2), which the TAB intends to apply for that product, or of the lack of such delegated act.3.If the Commission considers that an appropriate delegated act determining the assessment and verification system does not exist for the product, it may adopt a delegated act in accordance with Article 10(2).
Article 34Publication of references1.The Commission shall, in accordance with point 9 of Annex VI, assess the compliance of European assessment documents with harmonised technical specifications, with this Regulation and with other Union law. Where a European assessment document is in conformity with applicable legal requirements, the Commission shall without delay publish a reference of that document in the Official Journal of the European Union. Where a reference to a European assessment documents cannot be published in the Official Journal of the European Union, the Commission may publish such a reference with restrictions.2.Following publication in accordance with paragraph 1 of this Article, a European assessment document may, in accordance with Article 37, be used as a basis for a European technical assessment for a period of 10 years, unless the reference of the European assessment document has been withdrawn from the Official Journal of the European Union or that European assessment document is no longer used pursuant to Article 31(6). The organisation of TABs may in the last year of that period decide to submit the European assessment document for renewal. The Commission shall in that case reassess the European assessment document in accordance with paragraph 1 of this Article.
Article 35Content of the European assessment document1.A European assessment document shall contain the following elements:(a)a description of the product or product category covered and its intended use; and(b)the list of essential characteristics, relevant for the intended use of the product or product category as agreed between the manufacturer and the organisation of TABs as well as predetermined environmental essential characteristics as set out in Annex II, and the methods and criteria for assessing the performance of the product or product category in relation to the essential characteristics listed.2.The European assessment document shall set out:(a)the technical details necessary for the implementation of the assessment and verification systems that are to be applied in accordance with the delegated acts adopted under Article 10(2);(b)the guidelines, including technical details necessary for drawing up general product information, instructions for use and safety information as referred to in Annex IV;(c)the guidelines to ensure interoperability of the human and machine readable formats for the declaration of performance and conformity in accordance with paragraph 16(2), point (b).3.Where the performance of the product can appropriately be assessed by reference to its essential characteristics, including assessment methods and criteria, already established for them in harmonised technical specifications or other European assessment documents, those existing essential characteristics and their methods and criteria shall be incorporated as parts of the European assessment document, unless it is technically necessary to deviate from that rule.Where applicable, these principles shall also apply for threshold levels and classes of performance adopted in accordance with Article 5(5).
Article 36Formal objections against European assessment documents1.A Member State shall inform the Commission of all of the following:(a)where it considers that a European assessment document does not entirely conform with applicable legal requirements or satisfy the demands to be met in relation to the essential characteristics to be covered in view of the basic requirements for construction works set out in Annex I and the predetermined environmental essential characteristics set out in Annex II;(b)where it considers that a European assessment document raises a major concern for health and safety of persons, the protection of the environment or consumer protection;(c)where it considers that a European assessment document does not fulfil the requirements set out in Article 31(1).The Member State concerned shall substantiate its viewpoints. The Commission shall consult the other Member States on the issues raised by the Member State concerned.2.In the light of the views of all the Member States, the Commission shall decide to publish, not to publish, to publish with restriction, to maintain, to maintain with restriction or to withdraw the references to the European assessment documents concerned in the Official Journal of the European Union.3.The Commission shall inform the Member States and the organisation of TABs of its decision referred to in paragraph 2 and, where necessary, request the revision of the European assessment document concerned.
Article 37European technical assessment1.A European technical assessment shall be issued by a TAB, at the request of a manufacturer on the basis of a European assessment document the reference of which has been published in the Official Journal of the European Union in accordance with Article 34.Provided that there is a European assessment document the reference of which has been published in the Official Journal of the European Union in accordance with Article 34, a European technical assessment may be issued even in the case where a standardisation request has been issued. Such issuing shall be possible until the European assessment document is no longer used pursuant to Article 31(6).2.When a request for a European technical assessment is made, the procedure laid down in Annex VI shall apply.3.The European technical assessment shall include the performance to be declared, by levels or classes, or in a description, of those essential characteristics that are agreed by the manufacturer and the TAB receiving the request for the European technical assessment for the declared use, and the technical details necessary for the implementation of the assessment and verification system.The European technical assessment shall also include the assessment of the performance for the predetermined environmental essential characteristics listed in Article 15(3).4.The Commission may adopt implementing acts to establish the format of the European technical assessment.Those implementing acts shall be adopted in accordance with the examination procedure referred to in Article 90(3).5.European technical assessments issued on the basis of a European assessment document remain valid for either five years after the end of the period set out in Article 34(2) or five years after the reference of the European assessment document is withdrawn from the Official Journal of the European Union.When the relevant European assessment document for a product is no longer used pursuant to Article 31(6), that product may no longer be placed on the market on the basis of a European technical assessment.6.Products covered by a European assessment document for which a European technical assessment has been issued may be CE marked and thereby obtain the same status as products CE marked on the basis of harmonised technical specifications, where the manufacturer satisfies the obligations set out in this Regulation. Where these obligations refer to harmonised technical specifications, the manufacturer shall refer to the European assessment document instead or, where the harmonised technical specifications are also relevant, in addition.
CHAPTER VTECHNICAL ASSESSMENT BODIES
Article 38Designating authorities1.Member States wishing to designate TABs shall designate a single designating authority that shall be responsible for setting up and carrying out the necessary procedures for the assessment and designation of TABs. Designating authorities shall satisfy the requirements for notifying authorities set out in Articles 43(1) and Article 44. Member States may designate the notifying authority referred to in Article 43, as the designating authority. The designating authority shall not be eligible for designation in accordance with Article 39(1).2.Unless otherwise specified in this Chapter, the provisions applicable to notifying authorities and to notification procedures apply also to designating authorities and to the designation procedures.
Article 39Designation, monitoring and evaluation of TABs1.Member States may, through their designating authorities, designate TABs within their territories for one or several product families listed in Annex VII. Member States may also designate TABs within their territories as competent for emerging or innovative products that do not fall into already existing product families listed in Annex VII.Member States shall communicate the name of the TAB, its address and the product family or families it is competent for to the Commission.2.The Commission shall assign an identification number to each TAB.The Commission shall make publicly available the list of TABs designated under this Regulation by electronic means and indicate their identifications numbers, the product families for which they are designated and any limitations in the most precise possible way.The Commission shall ensure that that list is kept up-to-date.3.The designating authority shall monitor the activities and competence of the TABs designated in their respective Member State, and where necessary their subsidiaries and subcontractors, and evaluate them in relation to the respective requirements set out in this Chapter. The designating authority shall impose corrective measures on TABs wherever there is an infringement of this Regulation.Member States shall inform the Commission of their national procedures for the designation of TABs, of the monitoring of their activity and competence, and of any changes to that information.4.TABs shall, without delay, and at the latest within 15 days, inform the designating authority of any changes which may affect their compliance with the requirements set out in this Chapter or their ability to satisfy their obligations under this Regulation.5.TABs shall, at the request of the relevant designating authority, supply all relevant information and documents, required to enable that authority, the Commission and the Member States to verify their compliance with the requirements under this Regulation.6.Where a TAB no longer complies with the requirements of this Regulation, the designating authority shall restrict, suspend or withdraw the designation of that TAB for the relevant product family as appropriate, depending on the seriousness of the failure to meet those requirements. Where a TAB has repeatedly not complied with corrective measures imposed in accordance with paragraph 3 of this Article, the designating authority may restrict, suspend or withdraw the designation of that TAB. The designating authority shall inform the Commission and the other Member States of any restriction, suspension or withdrawal of a designation. Articles 53(2) and 54 shall apply.
Article 40Requirements for TABs1.A TAB shall be competent, and equipped, to carry out the assessment in relation to the product families for which it has been designated. The decision-making staff and at least half of the technical competent staff shall be employed by the TAB under the national law of the designating Member State.2.The TAB shall satisfy the requirements set out in Annex VIII, within the scope of its designation. Article 46(2) to (5), Article 46(6), points (a) and (b), Article 46(7), (8), (9) and (11) and Article 47 shall apply.3.A TAB shall have made publicly available its organigram and the names of the members of its internal decision-making bodies.4.A TAB shall participate in the activities of the organisation of TABs or ensure that their assessment personnel is informed about those activities.
Article 41Coordination of TABs1.The TABs shall establish an organisation for technical assessment ("organisation of TABs") under this Regulation.2.The organisation of TABs shall at least carry out the following tasks:(a)supply the Commission with relevant technical content relating to European assessment documents when the development of harmonised technical specifications based on the same product families is due to take place in accordance with the working plan referred to in Article 4(2). That information shall be based on close collaboration with the relevant European standardisation organisations;(b)organise the coordination of the TABs and, if necessary, ensure cooperation and consultation with other stakeholders;(c)ensure that examples of best practice are shared between TABs to promote greater efficiency and provide a better service to industry;(d)develop and adopt European assessment documents;(e)coordinate the application of the procedures set out in Article 59(2), Article 60(2) and in Article 61(2), as well as provide the support needed to that end;(f)inform the Commission of any question related to the preparation of European assessment documents and of any aspects related to the interpretation of the procedures set out in Article 60(2) and in Article 61(2) and suggest improvements to the Commission based on experience gained;(g)communicate any observations concerning a TAB not satisfying its tasks in accordance with the procedures set out in Article 60(2) and in Article 61(2) to the Commission and the Member State which designated the TAB;(h)report annually to the Commission on:(i)the fulfilment of the tasks referred to above;(ii)the allocation of European assessment document development tasks to the TABs;(iii)the even geographic distribution of tasks between TABs;(iv)the European technical assessments issued for each European assessment document including the geographical distribution of TABs involved and of the manufacturers receiving the documents; and(v)the performance and the independence of TABs; and;(i)ensure that adopted European assessment documents and references to European technical assessments are kept publicly available.The organisation of TABs shall set up a secretariat in order to carry out these tasks.3.Member States shall ensure that the TABs contribute adequately with financial and human resources to the organisation of TABs. Organisation of TABs shall establish the contribution of each TAB which shall be proportionate taking into account the annual budget or turnover of each TAB related to its activities as TAB.4.The weight in the decision-making process of the organisation of TABs shall not depend on the TABs’ financial contribution, the number of European assessment documents developed or the number of European technical assessments issued by them.5.The Commission shall be invited to participate in all meetings of the organisation of TABs.6.Union financing may be granted to the organisation of TABs for the implementation of the tasks referred to in paragraph 2. The Commission may make the financing of the organisation of TABs, whether by way of grants or public tenders, subject to the fulfilment of certain organisational and performance requirements set out in those tasks.
CHAPTER VINOTIFYING AUTHORITIES AND NOTIFIED BODIES
Article 42Notification1.Member States shall notify the Commission and the other Member States of bodies authorised to carry out third-party tasks in the assessment and verification of performance, assessment of conformity and of the verification of environmental sustainability calculations for the purposes of this Regulation.2.Member States shall inform the Commission of their procedures for the assessment and notification of bodies to be authorised to carry out these tasks and the monitoring of notified bodies, and of any changes thereto. The Commission shall make that information publicly available.
Article 43Notifying authorities1.Member States shall designate a notifying authority responsible for setting up and carrying out the necessary procedures for the assessment and notification of the bodies to be authorised to carry out third-party tasks in the assessment and verification process for the purposes of this Regulation, and the monitoring of notified bodies, including their compliance with requirements laid down in Articles 46 and 48.2.Member States may decide that the assessment and monitoring referred to in paragraph 1 is to be carried out by their national accreditation body within the meaning of and in accordance with Regulation (EC) No 765/2008.3.Where the notifying authority delegates or otherwise entrusts the assessment, notification or monitoring referred to in paragraph 1 of this Article to a body which is not a governmental entity that body shall be a legal person and shall comply mutatis mutandis with the requirements laid down in Article 44. In addition, it shall have arrangements to cover liabilities arising out of its activities.4.The notifying authority shall take full responsibility for the tasks performed by the body referred to in paragraphs 2 and 3.
Article 44Requirements relating to notifying authorities1.The notifying authority shall be established in such a way that no conflicts of interest with notified bodies occur.2.The notifying authority shall be organised and operated so as to safeguard the objectivity and impartiality of its activities.3.The notifying authority shall be organised in such a way that each decision relating to notification of a body to be authorised to carry out third-party tasks in the assessment and verification process is taken by competent persons different from those who carried out the assessment.4.The notifying authority shall not offer or provide any activities that notified bodies perform, or consultancy services on a commercial or competitive basis.5.The notifying authority shall safeguard the confidentiality of the information obtained. However, it shall, upon request, exchange information on notified bodies with the Commission, with notifying authorities of other Member States and with other competent national authorities which shall safeguard the confidentiality of the information received.6.The notifying authority, including in the cases in which the notifying authority is the national accreditation body, shall assess only the specific conformity assessment body applying for notification and not take account of the capacities or personnel of parent or sister companies. The notifying authority shall assess that body in relation to all relevant requirements and third-party assessment and verification tasks.7.The notifying authority shall have a sufficient number of competent personnel and sufficient funding at its disposal for the proper performance of its tasks.
Article 45Coordination of notifying and designating authorities1.The Commission shall ensure that appropriate coordination and cooperation between the Member States’ national authorities responsible for notification policy and the notifying and designating authorities is put in place and operated in the form of a coordination group of notifying and designating authorities in the field of construction products. That group shall meet on a regular basis and at least annually.Member States’ national authorities responsible for notification policy and the notifying and designating authorities under this Regulation shall participate in the activities of that group.2.The Commission may establish the specific arrangements for the functioning of the coordination group of the notifying and designating authorities.3.The Commission shall provide for the organisation of regular exchanges of experience between the Member States’ national authorities responsible for notification policy and the notifying and designating authorities.
Article 46Requirements relating to notified bodies1.For the purposes of notification, a conformity assessment body shall meet the requirements laid down in paragraphs 2 to 12.2.A conformity assessment body shall be established under the national law of a Member State and have legal personality.3.A conformity assessment body shall be a third-party body independent of the organisation or the product it assesses.It shall not have any business ties with organisations that have an interest in the products it assesses, in particular with manufacturers, their trade partners and their shareholding investors.However, a body belonging to a business association or professional federation representing undertakings involved in the design, manufacturing, provision, assembly, use or maintenance of products which it assesses, may, on condition that its independence and the absence of any conflict of interest are demonstrated, be considered such a body. This shall not preclude the body from carrying out assessment and verification activities for competing manufacturers.4.A conformity assessment body, its top-level management and the personnel responsible for carrying out the third-party tasks in the assessment and verification process shall not be the designer, manufacturer, supplier, importer, distributor, installer, purchaser, owner, user or maintainer of the products which it assesses, or the representative of any of those parties. This shall not preclude the use of assessed products that are necessary for the operations of the conformity assessment body or the use of products for personal purposes.A conformity assessment body, its top-level management and the personnel responsible for carrying out the third-party tasks in the assessment and verification process shall not be directly involved in the design, manufacture or construction, or marketing, installation, use or maintenance of those products, nor represent the parties engaged in those activities. They shall not engage in any activity that may conflict with their independence of judgement and integrity related to the activities for which they have been notified. This shall apply in particular to consultancy services in relation to product families for which they have been notified.Conformity assessment bodies shall ensure that activities of their parent or sister companies, their subsidiaries or subcontractors do not affect the confidentiality, objectivity and impartiality of their assessment or verification activities.A conformity assessment body shall not delegate to a subcontractor or a subsidiary the establishment and the supervision of internal procedures, general policies, codes of conduct or other internal rules, the assignment of its personnel to specific tasks and the conformity assessment decisions.5.Conformity assessment bodies and their personnel shall carry out the third-party tasks in the assessment and verification process with the highest degree of professional integrity and requisite technical competence in the specific field. They shall be free from all pressures and inducements, particularly financial, which might influence their judgement or the results of their assessment or verification activities, especially from persons or groups of persons with an interest in the results of those activities.6.A conformity assessment body shall be capable of carrying out all the third-party tasks in the assessment and verification process assigned to it in accordance with Annex IX in relation to which it has been notified, irrespective of whether those tasks are carried out by the conformity assessment body itself or on its behalf and under its responsibility.At all times and for each assessment and verification system and for each kind or category of products, essential characteristics and tasks in relation to which it has been notified, the conformity assessment body shall have the following at its disposal:(a)the necessary competent personnel with technical knowledge and sufficient and appropriate experience to perform the third-party tasks in the assessment and verification process;(b)the necessary description of the procedures in accordance with which the assessment process is carried out, ensuring the transparency and the ability of reproduction of those procedures, including a description of competence showing how relevant personnel, their status and tasks correspond to the conformity assessment tasks in relation to which the body intends to be notified;(c)appropriate policies and procedures to distinguish between the tasks it carries out as a conformity assessment body and its other activities;(d)procedures for the performance of activities, which take due account of the size of an undertaking, the sector in which it operates, its structure, the degree of complexity of the product technology in question and the mass or serial nature of the production process.The conformity assessment body shall have the means necessary to perform the technical and administrative tasks connected with the activities for which it intends to be notified in an appropriate manner and shall have access to all necessary equipment or facilities.7.The personnel responsible for carrying out the activities in relation to which the body intends to be notified, shall have the following:(a)sound technical and vocational training covering all the third-party tasks in the assessment and verification process within the relevant scope for which the body has been notified;(b)satisfactory knowledge of the requirements of the assessments and verifications it carries out and adequate authority to carry out such operations, including appropriate knowledge and understanding of the applicable harmonised technical specifications, European assessment documents and of the relevant provisions of the Regulation;(c)the ability required to draw up the certificates, records and reports to demonstrate that the assessments and the verifications have been carried out.8.Personnel responsible for taking assessment decisions shall:(a)be employed by the conformity assessment body under the national law of the notifying Member State;(b)not have any potential conflict of interest,(c)be competent to verify the assessments made by other staff, external experts or subcontractors;(d)be sufficient in number to ensure business continuity and a consistent approach to conformity assessments.9.The impartiality of the body and its top-level management and of the assessment personnel shall be guaranteed.The remuneration of the top-level management and assessment personnel of a body shall not depend on the number of assessments carried out or their results.10.A conformity assessment body shall take out liability insurance, unless liability is assumed by the Member State in accordance with national law, or the Member State itself is directly responsible for the assessment or the verification performed.11.The personnel of the conformity assessment body shall observe professional secrecy regarding all information obtained in carrying out its tasks under Annex IX, except in relation to the notifying authorities and other competent national authorities of the Member State in which its activities are carried out. Proprietary rights shall be protected.12.Conformity assessment bodies shall participate in, or ensure that their assessment personnel are informed about the relevant standardisation activities and the activities of the notified body coordination group established under this Regulation and shall apply as general guidance the administrative decisions and documents produced as a work result of that group.
Article 47Presumption of conformity of notified bodiesWhere a conformity assessment body to be authorised to carry out third-party tasks in the assessment and verification process demonstrates its conformity with the criteria laid down in the relevant harmonised standards the references of which have been published in the Official Journal of the European Union, harmonised technical specifications referred to in Article 5, European assessment documents, voluntary harmonised standards for product requirements the references of which have been published in the Official Journal of the European Union in accordance with Article 7(5) or (6) or the common specifications referred to in Article 8(1) or parts thereof, it shall be presumed to comply with the requirements set out in Article 46 in so far as the applicable documents cover those requirements.
Article 48Subsidiaries and subcontractors of notified bodies1.Where a notified body subcontracts specific tasks connected with the third-party tasks in the assessment and verification process or has recourse to a subsidiary, it shall ensure that the subcontractor or the subsidiary meets the requirements set out in Article 46, and shall inform the notifying authority accordingly.2.The notified body shall take full responsibility for the tasks performed by subcontractors or subsidiaries wherever these are established and monitor their competence in relation to its own as described in Article 46(6), point (b).3.Activities may be subcontracted or carried out by a subsidiary only with the agreement of the client.4.The notified body shall keep at the disposal of the notifying authority the relevant documents concerning the assessment and monitoring of the qualifications of the subcontractor or the subsidiary and the work carried out by them under Annex IX.
Article 49Use of facilities outside the testing laboratory of the notified body1.At the request of the manufacturer and where justified by technical, economic or logistic reasons related to the nature of the product or the test equipment, notified bodies may decide to carry out the tests referred to in Annex IX, for the assessment and verification systems 1+, 1 and 3 or have such tests carried out under their supervision, either in the manufacturing plants using the test equipment of the internal laboratory of the manufacturer or, with the prior consent of the manufacturer, in an external laboratory, using the test equipment of that laboratory.Notified bodies carrying out such tests shall be specifically designated as competent to work away from their own test facilities and shall also in that regard comply with the requirements laid down in Article 46.2.Before carrying out the tests referred to in paragraph 1, notified bodies shall verify whether the requirements of the test method are satisfied and shall evaluate whether:(a)test equipment has an appropriate calibration system and the traceability of the measurements is guaranteed; and(b)the quality of the test results is ensured.Notified bodies shall assume full responsibility for the tests in their entirety, including the accuracy and traceability of calibration and measurements, and for the reliability of the test results.
Article 50Application for notification1.A body to be authorised to carry out third-party tasks in the assessment and verification systems shall submit an application for notification to the notifying authority of the Member State in which it is established.2.The application shall be accompanied by a description of the activities to be performed, the assessment and verification processes for which the body claims to be competent, the description of competence referred to in Article 46(6), point (b), as well as an accreditation certificate, where one exists, issued by the national accreditation body, attesting that the body fulfils the requirements laid down in Article 46. The accreditation certificate shall relate only to the precise legal body applying for notification and shall be based, in addition to relevant harmonised standards, on the specific requirements and tasks provided for in this Regulation.3.Where the body concerned cannot provide an accreditation certificate, it shall provide the notifying authority with all the documentary evidence necessary for the verification, recognition and regular monitoring of its compliance with the requirements laid down in Article 46.
Article 51Notification procedure1.Notifying authorities may notify only bodies which have satisfied the requirements laid down in Article 46.2.Notifying authorities shall notify the Commission and the other Member States using the electronic notification tool developed and managed by the Commission.Exceptionally, for cases regarding groupings of essential characteristics set out in Annex X, for which the appropriate electronic tool is not available, a notification in other electronic form shall be accepted.3.The notification shall include full details of the functions to be performed, reference to the relevant harmonised technical specification or to the relevant European assessment document and, for the purposes of the system set out in Annex IX, the essential characteristics for which the body is competent and the relevant attestation of that competence.However, reference to the relevant harmonised technical specification or to the relevant European assessment document is not required in the cases regarding groupings of essential characteristics set out in Annex X.4.Where a notification is not based on an accreditation certificate as referred to in Article 50(2), the notifying authority shall provide the Commission and the other Member States with all documentary evidence which attests to the body’s competence and the arrangements in place to ensure that that body will be monitored regularly and will continue to satisfy the requirements laid down in Article 46.5.The body concerned may perform the activities of a notified body if the Commission or the other Member States do not raise any objections within two weeks of a notification, where an accreditation certificate is used, or within two months of notification, where an accreditation certificate is not used.Only such a body shall be considered a notified body for the purpose of this Regulation.6.Valid notifications shall be included by the Commission in the list of notified bodies referred to in Article 52(2).7.The Commission and the other Member States shall be notified of any subsequent relevant changes to the notification.
Article 52Identification numbers and lists of notified bodies1.The Commission shall assign an identification number to a notified body.It shall assign a single such number even where the body is notified under several Union acts.2.The Commission shall make publicly available the list of bodies notified under this Regulation, including the identification numbers that have been assigned to them and the activities for which they have been notified.The Commission shall ensure that that list is kept up-to-date.
Article 53Changes to the notification1.Where a notifying authority has ascertained or has been informed that a notified body no longer meets the requirements laid down in Article 46, or that it is failing to fulfil its obligations, the notifying authority shall restrict, suspend or withdraw the notification as appropriate, depending on the seriousness of the failure to meet those requirements or to fulfil those obligations. It shall immediately inform the Commission and the other Member States accordingly.2.In the event of a restriction, suspension or withdrawal of a notification, or where the notified body has ceased its activity, the notifying Member State shall take appropriate steps to ensure that that body’s files are either processed by another notified body or kept available for the responsible notifying and competent national authorities at their request.
Article 54Challenge of the competence of notified bodies1.The Commission shall investigate all cases where it doubts, or doubt is brought to its attention regarding, the competence of a notified body or the continued fulfilment by a notified body of the requirements and responsibilities to which it is subject.2.The notifying Member State shall provide the Commission, on request, with all information related to the basis for notification or the maintenance of the competence of the body concerned.3.The Commission shall ensure that all sensitive information obtained in the course of its investigations is treated confidentially.4.Where the Commission ascertains that a notified body does not meet, or no longer meets, the requirements for its notification, it shall inform the notifying Member State accordingly and request it to take the necessary corrective measures, including withdrawal of notification if necessary.
Article 55Operational obligations of notified bodies1.Notified bodies shall, in accordance with Annex IX carry out the following assessments and verifications:(a)assess the performance and the conformity of products;(b)verify the conformity of products;(c)verify the constancy of performance of products;(d)validate the environmental sustainability calculations undertaken by the manufacturer;(e)verify the compliance of the manufacturer with the obligations of this Regulation.Those tasks are hereinafter referred to as "assessments and verifications".2.Assessments and verifications shall be carried out with transparency as regards the manufacturer, and in a proportionate manner, avoiding an unnecessary burden for economic operators. The notified bodies shall perform their activities taking due account of the size of the undertaking, the sector in which the undertaking operates, its structure, the degree of complexity of the product technology in question and the mass or serial nature of the production process.In so doing, the notified bodies shall nevertheless respect the degree of rigour required for the product by this Regulation and the part played by the product for the fulfilment of all basic requirements for construction works.3.Where, in the course of the initial inspection of the manufacturing plant and of factory production control, a notified body finds that the manufacturer has not ensured the constancy of performance and conformity of the manufactured product, it shall require the manufacturer to take appropriate corrective measures and shall not issue a certificate or a validation report.4.Where, in the course of the monitoring activity aiming at the verification of conformity and of the constancy of performance of the manufactured product, a notified body finds that a product no longer has the same performance to that of the product-type, it shall require the manufacturer to take appropriate corrective measures and shall suspend or withdraw the certificate or the validation report if necessary.5.Where corrective measures are not taken or do not have the required effect, the notified body shall restrict, suspend or withdraw any certificates or validation reports, as appropriate.6.When taking assessment decisions, including when deciding on the need to suspend or withdraw a certificate or validation report in light of possible instances of non-compliance, notified bodies shall apply clear and pre-determined criteria.7.When requested by a manufacturer or provider to do so, notified bodies shall cooperate and share all relevant information with notified bodies that have recognised its assessments and verifications in accordance with Article 62. Notified bodies shall establish an agreement for that purpose.
Article 56Information obligations of notified bodies1.Notified bodies shall inform the notifying authority of the following:(a)any refusal, restriction, suspension or withdrawal of certificates, validation reports or test reports;(b)any circumstances affecting the scope of, and conditions for, notification;(c)any request for information on assessment or verification activities carried out which they have received from competent national authorities; and(d)on request, third-party tasks in accordance with the assessment and verification systems carried out within the scope of their notification and any other activity performed, including cross-border activities and subcontracting.2.Notified bodies shall provide the other bodies notified under this Regulation which carry out similar third-party tasks in accordance with the assessment and verification systems and for products covered by the same harmonised technical specification or the same European assessment document with relevant information on issues relating to negative results from these assessments and verifications, in particular, any refusal, restriction, suspension, or withdrawal of certificates, validation reports or of test reports, and, upon request, positive results from those assessments.A notified body shall, upon request from another notified body, a competent national authority or the Commission inform the requesting party whether certificates, validation reports or test reports issued by it are valid, restricted, suspended or withdrawn.3.Where the Commission or a competent national authority of a Member State submits a request to a notified body established on the territory of another Member State relating to an assessment carried out by that notified body, it shall send a copy of that request to the notifying authority of that other Member State. The notified body concerned shall respond without delay and within 15 days at the latest to the request. The notifying authority shall ensure that such requests are resolved by the notified body unless there is a legitimate reason for not doing so.4.Where notified bodies have or receive evidence that:(a)another notified body does not comply with the requirements laid down in Article 46 or its obligations;(b)a product placed on the market does not comply with this Regulation;(c)a product placed on the market, due to its physical condition, is likely to cause a serious risk,they shall alert and share such evidence with the relevant market surveillance authority or notifying authority, as appropriate.
Article 57Implementing acts on notified bodies’ obligationsWhere this is necessary to ensure a harmonised application of this Regulation and where the coordination group of notifying and designating authorities have not been able to resolve a dispute concerning their diverging practices, in accordance with Article 45, and only to the extent necessary to prevent diverging practices fragmenting the internal market for economic operators, the Commission may adopt implementing acts providing details on how to execute the obligations of notified bodies contained in Articles 55 and 56.Those implementing acts shall be adopted in accordance with the examination procedure referred to in Article 90(3).
Article 58Coordination of notified bodies1.The Commission shall ensure that appropriate coordination and cooperation between bodies notified under this Regulation are put into place and properly operated in the form of a group of notified bodies.Notified bodies shall participate in the work of that group, directly or by means of designated representatives. Notifying authorities shall ensure that notified bodies participate in the work of that group.2.Notified bodies shall apply as general guidance any relevant documents produced as a result of the work of the group referred to in paragraph 1.3.Coordination and cooperation in the group referred to in paragraph 1 shall aim to ensure the harmonised application of this Regulation.
CHAPTER VIISIMPLIFIED PROCEDURES
Article 59Replacement of type-testing and type-calculation1.A manufacturer may replace type-testing or type-calculation with a specific section in the technical documentation referred to in Article 22(3) demonstrating that:(a)for one or several essential characteristics of the product, which the manufacturer places on the market, that product is deemed to achieve a certain level or class of performance without testing or calculation, or without further testing or calculation, in accordance with the conditions set out in the delegated acts referred to in Article 5(6); or(b)the product, covered by a harmonised technical specification or a European assessment document, which the manufacturer places on the market is a system made of components, which the manufacturer duly assembles following precise instructions, including compatibility criteria in the case of individual components, given by the provider of such a system or of a component thereof, who has already tested that system or that component for one or several of its essential characteristics in accordance with the relevant harmonised technical specification or European assessment document. When these conditions are satisfied and when the manufacturer has notably verified that the precise compatibility criteria of the provider are met, the manufacturer is entitled to declare performance corresponding to all or part of the test results provided to it for the system or the component;(c)the product, covered by a harmonised technical specification or by a European technical assessment, which the manufacturer places on the market, corresponds to a product-type of a product manufactured by another manufacturer and is already subject to type-testing or type-calculation.When the conditions in point (c) are satisfied, the manufacturer may declare the performance corresponding to all or part of the results of this other product. The manufacturer shall only apply this simplification after having obtained an authorisation of the other manufacturer, who remains responsible for the accuracy, reliability and stability of those test results.2.If the assessment and verification system applicable includes a performance assessment by a notified body as set out in Annex IX, a notified body or TAB shall, in place of the assessment of the performance of the product set out in Annex IX, assess and certify the correct fulfilment of the obligations referred to in paragraph 1 of this Article.
Article 60Use of simplified procedures by micro-enterprises1.A micro-enterprise may replace type-testing or type-calculation for an essential characteristic under assessment and verification system 3 set out in point 5 of Annex IX with a specific section in the technical documentation referred to in Article 22(3) providing data equivalent to the assessment required for this essential characteristic in accordance with the applicable harmonised technical specifications or European assessment document.2.A notified body or TAB shall, instead of the assessment of the performance of the product set out in Annex IX, assess and certify the correct fulfilment of the obligations referred to in paragraph 1 of this Article.
Article 61Custom-made non-series products1.As an alternative to the exemption in Article 14, point (a), a manufacturer of a product that fulfils the conditions in Article 14, point (a), may replace the performance assessment of the product with a specific section in the technical documentation referred to in Article 22(3) demonstrating the compliance of that product with the applicable requirements and providing data equivalent to the data required by this Regulation and the applicable harmonised technical specifications or European assessment document.2.If the assessment and verification system applicable includes a performance assessment by a notified body as set out in Annex IX, a notified body or TAB shall, in place of the assessment of the performance of the product set out in Annex IX, assess and certify the correct fulfilment of the obligations referred to in paragraph 1 of this Article.
Article 62Recognition of assessment and verification by another notified body1.When a notified body is to assess and verify a certain product in accordance with Annex IX, it may refrain from the assessment and verification and recognise the assessment and verification undertaken by another notified body for the same economic operator where all of the following conditions apply:(a)the product has been correctly assessed and verified by the other notified body;(b)the assessed or verified economic operator agrees to share all relevant data and documents with the recognising notified body; and(c)the validity of the certificate is limited to the validity of the certificate issued by the other notified body.This paragraph shall also apply to validation reports and to assessments of calculation of the environmental sustainability undertaken under Regulation (EU) 2024/1781.2.When a notified body is to assess and verify a certain product in accordance with Annex IX, it may refrain from the assessment and verification of its parts or materials and recognise the results of the assessment and verification by another notified body, if the provider of those parts or materials applied the required assessment and verification system to them and there is an agreement between the manufacturer of the product and the provider that ensures the free flow of all information between them and the notified bodies in view of ensuring compliance with this Regulation.This paragraph shall also apply to assessments of the calculation of the environmental sustainability undertaken under Regulation (EU) 2024/1781.
CHAPTER VIIIMARKET SURVEILLANCE AND SAFEGUARD PROCEDURES
Article 63Complaint portal1.Without prejudice to the obligations of economic operators under this Regulation and the activities of market surveillance authorities under Regulation (EU) 2019/1020, the Commission shall set up a system allowing any natural or legal person to share complaints or reports related to possible non-compliance with this Regulation.2.Where the Commission considers a complaint or report relevant and substantiated based on clearly defined criteria, it shall without undue delay transmit that complaint or report to the single liaison point of the Member State concerned for that single liaison point to follow-up with the relevant natural or legal person in accordance with Article 11(7), point (a) of Regulation (EU) 2019/1020.
Article 64Market surveillance authorities and single liaison point1.Member States shall designate, amongst their market surveillance authorities, one or more authorities that dispose of the particular knowledge needed to assess products both technically and legally.2.Member States shall designate a single liaison point to act as the focal point for contacts with the Commission and single liaison points of other Member States which are competent under this Regulation, including for requests pursuant to Articles 22, 23 and 24 of Regulation (EU) 2019/1020.3.Market surveillance authorities designated in accordance with paragraph 1 of this Article shall have all the powers listed in Article 14 of Regulation (EU) 2019/1020. For the purposes of this Regulation those powers shall also apply to all economic operators covered by this Regulation.4.For the purpose of market surveillance, investigation and enforcement, market surveillance authorities shall have the power to request from other authorities or bodies relevant information in their possession.
Article 65Procedure to deal with non-compliance1.Where a market surveillance authority of one Member State has sufficient reason to believe that certain products covered by a harmonised technical specification or for which a European technical assessment has been issued, or their manufacturer, are non-compliant, it shall carry out an evaluation in relation to those products and the manufacturer concerned covering the respective requirements laid down by this Regulation. The relevant economic operators shall, as necessary, cooperate with the market surveillance authorities.Where, in the course of that evaluation, the market surveillance authority finds that the products or their manufacturer do not comply with the requirements and obligations laid down in this Regulation, it shall without delay require the relevant economic operator to take appropriate and proportionate corrective actions, as provided for in Article 16(3) of Regulation (EU) 2019/1020, to bring the non-compliance to an end or, if that is not possible, to withdraw the products from the market, or to recall them, all within a reasonable period which is commensurate with the nature of the non-compliance.The market surveillance authority shall inform the notified bodies accordingly, if notified bodies are involved.2.Where the market surveillance authority considers that the non-compliance is not limited to its national territory, it shall, via the single liaison point, inform the Commission and the other Member States of the results of the evaluation and of the actions which it has required the economic operator to take.3.The economic operator shall ensure that all appropriate corrective action is taken in respect of all the products concerned that it has made available on the market throughout the Union.4.Where the relevant economic operator, within the period referred to in the second subparagraph of paragraph 1, does not take the corrective action referred to in paragraph 1, second subparagraph, or where the non-compliance persists, the market surveillance authority shall ensure that the product concerned is withdrawn or recalled, or that making it available on the market is prohibited or restricted.The market surveillance authority shall inform the public, and via the single liaison point the Commission and the other Member States, without delay, of those measures.5.The information referred to in the second subparagraph of paragraph 4 shall include all available details, in particular the data necessary for the identification of the non-compliant products, the origin of those products, the nature of the non-compliance alleged and the risk involved, the nature and duration of national measures taken as well as the arguments put forward by the relevant economic operator. In particular, the market surveillance authorities shall indicate whether the non-compliance is due to any of the following:(a)failure of the products to achieve the declared performance;(b)failure of the products to meet product requirements established by delegated acts referred to in Article 7(1);(c)failure of the manufacturer to meet obligations;(d)shortcomings in the harmonised technical specifications, in a European assessment document, in the voluntary harmonised standards for product requirements the references of which have been published in the Official Journal of the European Union in accordance with Article 7(5) or (6) or in the common specifications established by implementing acts referred to in Article 8(1).6.Member States other than the Member State initiating the procedure shall without delay inform the Commission and the other Member States of any measures adopted and of any additional information at their disposal relating to the non-compliance of the products concerned, and, in the event of disagreement with the notified national measure, of their objections.7.Where, within two months of receipt of the information referred to in paragraph 4, no objection has been raised by either a Member State or the Commission in respect of a provisional measure taken by a Member State in relation to the product concerned, that measure shall be deemed justified.8.Member States shall ensure that appropriate restrictive measures are taken without delay in respect of the product or manufacturer concerned, such as withdrawal of the products from their market.
Article 66Union safeguard procedure1.Where, on completion of the procedure set out in Article 65(4), (6) and (7), objections are raised against a measure taken by a Member State or where the Commission considers a national measure to be contrary to Union legislation, the Commission shall without delay enter into consultation with the Member States and the relevant economic operator and shall evaluate the national measure. The consultation period shall not exceed two months. On the basis of the results of that evaluation, the Commission shall endeavour to adopt implementing acts, within two additional months, after the end of consultation period, setting out its decision as to whether the measure is justified or not.Those implementing acts shall be adopted in accordance with the advisory procedure referred in Article 90(2).The Commission shall address its decision to all Member States and shall immediately communicate it to them and to the relevant economic operator.2.If the national measure is considered to be justified, all Member States shall, without delay, ensure that appropriate restrictive measures, such as withdrawal, are taken in respect of the non-compliant product and shall inform the Commission accordingly. If the national measure is considered to be unjustified, the Member State concerned shall withdraw the measure.3.Where the national measure is considered to be justified and the non-compliance of the product or its manufacturer is attributed to shortcomings in the harmonised technical specifications, European assessment documents, voluntary harmonised standards or common specifications established by implementing acts as referred to in Article 65(5), point (d), the Commission shall apply the procedure provided for in Article 5(9), Article 6(5), Article 7(6) or Article 36 of this Regulation or in Article 11 of Regulation (EU) No 1025/2012, as appropriate.
Article 67Compliant products which nevertheless present a risk1.Where, having performed an evaluation pursuant to Article 65(1), a market surveillance authority finds that, although a product is in compliance with this Regulation, it presents a risk to the health or safety of persons or, where applicable, to the environment or to other aspects of public interest protection, it shall require the relevant economic operator to take all appropriate measures to ensure that the products concerned, when placed on the market, no longer present that risk, to withdraw the products from the market or to recall them within a reasonable period, commensurate with the nature of the risk, which it may prescribe.2.The economic operator shall ensure that any corrective action is taken in respect of all the products concerned which that economic operator has made available on the market throughout the Union.3.The market surveillance authority shall, via the single liaison point, immediately inform the Commission and the other Member States. That information shall include all available details, in particular the data necessary for the identification of the product concerned, the origin and the supply chain of the product, the nature of the risk involved and the nature and duration of the national measures taken.4.The Commission shall without delay consult the Member States and the relevant economic operators and shall evaluate the national measures taken. On the basis of the results of that evaluation, the Commission shall adopt an implementing act setting out its decision whether the measure is justified or not and, where necessary, ordering appropriate measures.Those implementing acts shall be adopted in accordance with the advisory procedure referred to in Article 90(2).5.The Commission shall address its decision to all Member States and shall immediately communicate it to them and to the relevant economic operator.
Article 68Market surveillance coordination and support1.For the purposes of this Regulation, the administrative cooperation group set up pursuant to Article 30(2) of Regulation (EU) 2019/1020 ("ADCO") shall meet at regular intervals and, where necessary, at the reasoned request of the Commission or of two or more participating market surveillance authorities.In the context of performing its tasks set out in Article 32 of Regulation (EU) 2019/1020, the ADCO shall support the implementation of this Regulation, namely by identifying common priorities for market surveillance.2.Based on priorities identified in consultation with the ADCO, the Commission shall:(a)organise joint market surveillance and testing projects in areas of common interest;(b)organise joint investment in market surveillance capacities, including equipment and IT tools;(c)organise common trainings for the staff of market surveillance authorities, notifying authorities and notified bodies, including on the correct interpretation and application of this Regulation and on methods and techniques relevant for applying or verifying compliance with it;(d)draw up guidelines for the application and enforcement of this Regulation, including requirements and obligations set out in harmonised technical specifications adopted pursuant to this Regulation, as well as common practices and methodologies for effective market surveillance.The Union shall, where appropriate, finance the actions referred to in points (a), (b) and (c).3.The Commission shall provide technical and logistic support to ensure that the ADCO fulfils its tasks set out in this Article and in Article 32 of Regulation (EU) 2019/1020.
Article 69Recovery of costsWhere a product has been found to be non-compliant, market surveillance authorities shall have the right to recover from the economic operators who placed or made the product available on the market the costs of document inspection and physical product testing, provided that those costs are accompanied by a justification.
Article 70Reporting and benchmarking1.Market surveillance authorities shall enter into the information and communication system referred to in Article 34 of Regulation (EU) 2019/1020 information on the nature and severity of any penalty imposed in relation to non-compliance with this Regulation.2.Every four years, by 30 June, the Commission shall, draw up a report based on the information entered by market surveillance authorities into the information and communication system referred to in Article 34 of Regulation (EU) 2019/1020. The first of those reports shall be published by 9 January 2030.The report shall include:(a)information on the nature and number of checks performed by market surveillance authorities during the four previous calendar years pursuant to Article 34(4) and (5) of Regulation (EU) 2019/1020;(b)information on the levels of non-compliance identified and on the nature and severity of penalties imposed for the four previous calendar years in relation to products covered by harmonised technical specifications or CE marked based on a European technical assessment;(c)indicative benchmarks for market surveillance authorities in relation to the frequency of checks and the nature and severity of penalties imposed.3.The Commission shall publish the report referred to in paragraph 2 of this Article in the information and communication system referred to in Article 34 of Regulation (EU) 2019/1020 and shall make public a summary of the report.
CHAPTER IXINFORMATION AND ADMINISTRATIVE COOPERATION
Article 71Information systems for harmonised decision-making1.The Commission shall establish and maintain an information and communication system for the collection, processing and storage of information, in a structured form, on issues relating to the interpretation or application of the rules laid down in or pursuant to this Regulation, with the aim of ensuring the harmonised application of those rules.In addition to the Commission and Member States, market surveillance authorities, the single liaison offices appointed under Article 10(3) of Regulation (EU) 2019/1020, the authorities designated under Article 25(1) of Regulation (EU) 2019/1020, notifying authorities, representatives of the group of notified bodies and of the organisation of TABs, and product contact points for construction shall be able to access the information and communication system.2.The bodies listed in paragraph 1 may use the information and communication system to raise any question or issue related to the interpretation or application of the rules laid down in or pursuant to this Regulation, including their relationship to other provisions of Union law.3.For the purposes of paragraph 2, the bodies listed in paragraph 1 may raise questions or issues related to the following topics:(a)the application or interpretation by any other body of the rules laid down in, or pursuant to, this Regulation in a way that diverges from their own practice;(b)questions or issues raised through the information and communication system related to the situation they are confronted with or to their own practice;(c)situations not foreseen by the rules laid down in or pursuant to this Regulation when first published or referred to in the Official Journal of the European Union, especially but not limited to situations brought about by the emergence of new products or business models;(d)whether the rules laid down in or pursuant to this Regulation apply to a situation to which other provisions of Union law also apply and the resulting question of which rules are to prevail.4.When raising a question or issue, the relevant body shall enter into the information and communication system information concerning:(a)any decision taken in relation to the question or issue raised;(b)the rationale behind the approach taken;(c)any alternative approach it has identified and its rationale.5.Member States shall establish a national information system or email distribution service to inform their competent national authorities, the economic operators active on their territory, TABs and notified bodies with place of business on their territory and, on request, also other TABs and notified bodies, on all matters relevant for the correct interpretation or application of the rules laid down in or pursuant to this Regulation. In doing so, they shall take into account the information available in the information and communications system referred to in paragraph 1.6.Competent national authorities, TABs and notified bodies with a place of business in the respective Member State shall register themselves in the system or for the email distribution service and take account of all information transmitted via them. Economic operators may register themselves in the system or for the email distribution service. Member States shall take appropriate measures to bring the system or email distribution service to the attention of economic operators.7.The national information system or email distribution service shall be able to receive complaints from any natural or legal person, including TABs and notified bodies, on the uneven application of the rules laid down in or pursuant to this Regulation. If deemed appropriate, the single liaison point shall forward such complaints to their peers in other Member States and to the Commission.
Article 72Product contact points for construction1.Member States shall support economic operators by product contact points for construction. Member States shall designate and maintain at least one product contact point for construction on their territory and shall ensure that their product contact points for construction have sufficient powers and adequate resources for the proper performance of their tasks. They shall ensure that product contact points for construction deliver their services in accordance with Regulation (EU) 2018/1724 and that they coordinate with the product contact points for mutual recognition established pursuant to Article 9(1) of Regulation (EU) 2019/515 of the European Parliament and of the CouncilRegulation (EU) 2019/515 of the European Parliament and of the Council of 19 March 2019 on the mutual recognition of goods lawfully marketed in another Member State and repealing Regulation (EC) No 764/2008 (OJ L 91, 29.3.2019, p. 1)..2.Product contact points for construction shall provide, at the request of an economic operator or a competent national authority of another Member State, any useful product related information, such as:(a)electronic copies of, or online access to, the national technical rules and national administrative procedures applicable to products in the territory in which the product contact points for construction is established;(b)information on whether those products are subject to prior authorisation under national law;(c)rules applicable to the incorporation, assembling or installation of products.Product contact points for construction shall also provide information on product related provisions of this Regulation and of acts adopted in accordance with it.3.Product contact points for construction shall provide information free of charge within 15 working days of receiving any request under paragraph 2.4.Product contact points for construction shall be able to carry out their functions in a manner that avoids conflicts of interest, particularly in respect of the procedures for obtaining the CE marking.5.Paragraphs 1 to 4 apply also to products which have not yet been covered by harmonised technical specifications.6.The Commission shall publish and keep up-to-date a list of the national product contact points for construction.
Article 73Training and exchange of staff1.Market surveillance authorities, product contact points for construction, designating authorities, TABs, notifying authorities, and notified bodies shall ensure that their staff:(a)keep up-to-date in their area of competence and receive periodic additional training to that end; and(b)receive periodically training on the harmonised interpretation and application of the rules laid down in or pursuant to this Regulation.2.The Commission shall, periodically and at least once a year, organise training events jointly for the staff of market surveillance authorities, product contact points for construction, designating authorities, notifying authorities, and notified bodies. The Commission shall organise these training events in cooperation with the Member States.The training events shall be open to the participation of the staff of the authorities designated under Article 25(1) of Regulation (EU) 2019/1020, the single liaison offices appointed under Article 10(3) of Regulation (EU) 2019/1020 and, where appropriate, of other authorities of the Member States involved in the implementation or enforcement of this Regulation.3.The Commission may organise, in cooperation with the Member States, programmes for the exchange of staff between the market surveillance authorities, notifying authorities, and notified bodies of two or more Member States.
Article 74Shared roles and joint decision-making1.In order to fulfil their obligations under this Regulation with regard to market surveillance, designation and supervision of TABs, notified bodies, and product contact points for construction, Member States may designate:(a)a body or authority set up in cooperation with another Member State or other Member States for the purpose of joint designation;(b)a body or authority already designated by another Member State for the same purpose, in cooperation with that Member State.The Member States concerned shall jointly ensure that the shared bodies or authorities meet all relevant requirements. They shall be jointly responsible for them, whilst decisions taken towards natural or legal persons on a certain Member State shall be legally attributable only to that Member State.2.The authorities of different Member States may, without prejudice to their individual obligations under this Regulation or other legislative acts, share resources and responsibilities in order to ensure the harmonised application or effective enforcement of this Regulation.To that end, they may also:(a)take joint decisions, especially in relation to joint cross-border activities or in relation to economic operators active on the territory of the relevant Member States;(b)establish common projects, such as joint market surveillance or testing projects;(c)pool resources for specific purposes, such as building up testing capacity or for internet surveillance;(d)delegate the execution of tasks to a peer authority of another Member State, whilst staying formally responsible for the decisions taken by that authority;(e)transfer a task from one Member State to the other, provided that such transfer is clearly communicated to all concerned.The relevant Member States shall be jointly responsible for the actions taken in accordance with this paragraph.
CHAPTER XDIGITAL PRODUCT PASSPORT
Article 75Construction digital product passport system1.The Commission shall adopt delegated acts in accordance with Article 89 to supplement this Regulation by setting up a construction digital product passport system, in accordance with the conditions set out in this Chapter.2.The construction digital product passport system shall:(a)be compatible with, interoperable with and based upon the digital product passport established by Regulation (EU) 2024/1781, without compromising interoperability with Building Information Modelling (BIM), and taking into account the specific characteristics and requirements related to construction products;(b)have the functionalities required to implement and manage digital product passports referred to in Article 76;(c)determine the actors, including economic operators, clients, deinstallers, users and competent national authorities, which are to have access to information in the digital product passport and to what information they are to have access, taking into account the need to protect intellectual property rights, and sensitive commercial information, and to ensure the safety of construction works;(d)determine the actors, including manufacturers, authorised representatives, importers, distributors and digital product passport service providers, which are allowed to introduce or update the information in the digital product passport, including where necessary the creation of a new digital product passport, and what information they may introduce or update;(e)lay down detailed arrangements for updating the information in the digital product passport of an existing product;(f)establish procedures to ensure the availability of digital product passports after an insolvency, a liquidation or a cessation of activity in the Union of the economic operator that created the digital product passport or, if necessary, after the obligations of manufacturers to ensure its availability have expired, including the establishment of a back-up system by digital product passport service providers;(g)establish requirements for digital product passport service providers, including, if required, a certification scheme to verify such requirements, to be based upon developments under Regulation (EU) 2024/1781 for the same purpose, as far as possible;(h)when required, lay down more detailed or alternative rules and procedures related to the life cycle of identifiers, data carriers, digital credentials and the digital product passport registry to those established by Regulation (EU) 2024/1781 for the same purpose;(i)ensure that the system is accessible for period of 25 years after the last product corresponding to its product type has been placed on the market and that the economic operator makes available the digital product passport for at least 10 years, without„ in the case of a longer period, creating a disproportionate cost and burden for the economic operators;(j)take into account the need to ensure the availability of information for the reuse and remanufacturing of products.
Article 76Digital product passport1.The information in the digital product passport shall be accurate, complete, and up-to-date.2.A digital product passport for a product under this Regulation shall:(a)include the following information:(i)the declaration of performance and conformity referred to in Article 15, including the information referred to in Article 15(6) which can be included through a connection to other Union databases where it is available and the documentation provided together in accordance with Annex V;(ii)the general product information, instructions for use and safety information referred to in Article 22(6);(iii)the technical documentation referred to in Article 22(3) including the specific sections required pursuant to Articles 59 to 61;(iv)the label in accordance with Article 22(9);(v)unique identifiers issued in accordance with Article 79(1);(vi)documentation required under other Union law applicable to the product;(vii)data carriers of key parts for which a digital product passport is available;(b)be connected to one or more data carriers;(c)be accessible by electronic means through the data carrier displayed, in accordance with Article 18(2), point (g);(d)correspond to the product type and its unique identification code referred to in Article 22(5);(e)be accessible free of charge to all economic operators, clients, users and authorities through the data carrier;(f)give different levels of access to the construction digital product passport system;(g)allow actors specified in the construction digital product passport system to introduce or to update the information in the digital product passport;(h)be accessible for an established period after the last product corresponding to its product type has been placed on the market.3.The requirements referred to in paragraph 2 shall:(a)ensure that actors along the value chain can easily access and understand product information relevant to them;(b)facilitate the verification of product compliance by competent national authorities; and(c)improve traceability of products along the value chain.4.Products in respect of which the exemption established in Article 14 is applied are also exempt from the obligation to provide a digital product passport.
Article 77General requirements for the digital product passport1.A digital product passport shall meet the following conditions:(a)it shall be connected through one or more data carriers to a persistent unique identification code of the product type;(b)the data carrier shall be affixed in accordance with Article 18(2), point (g);(c)the data carrier shall comply with Article 79(1);(d)all information included in the digital product passport shall be based on open standards, developed with an interoperable format and shall, as appropriate, be machine-readable, structured, searchable and transferable through an open interoperable data exchange network, without "vendor lock-in", in accordance with the essential requirements set out in Article 78; documents provided together with the declaration of performance and conformity referred to in Article 76(2)(a)(i) and technical documentation referred to in Article 76(2)(a)(iii) shall be exempted from this obligation when justified for technical reasons;(e)personal data related to the end-user of the product shall not be stored in the digital product passport without the explicit consent of the end-user in compliance with Article 6 of Regulation (EU) 2016/679 of the European Parliament and of the CouncilRegulation (EU) 2016/679 of the European Parliament and of the Council of 27 April 2016 on the protection of natural persons with regard to the processing of personal data and on the free movement of such data, and repealing Directive 95/46/EC (General Data Protection Regulation) (OJ L 119, 4.5.2016, p. 1).;(f)the information in the digital product passport shall include a reference to the product type referred to in Article 76(2), point (d);(g)the access to information included in the digital product passport shall be regulated in accordance with the essential requirements set out in Article 78 and the specific access rights shall be identified in accordance with construction digital product passport system levels of access;(h)the declaration of performance and conformity referred to in Article 76(2), point (a)(i), shall follow the guidelines issued in accordance with Article 16(3).2.Where other Union legislation requires or allows the inclusion of specific information in the digital product passport, that information may be included in the digital product passport in accordance with the delegated act referred to in Article 75(1).3.The manufacturer placing the product on the market shall provide actors making the products available on the market online or through other means of distance sales with a digital copy of the data carrier and the product identifier to allow them to make it accessible to customers where they cannot physically access the product. The economic operator shall provide that digital copy or a webpage link free of charge and within 5 working days of receiving the request.
Article 78Technical design and operation of the digital product passportThe technical design and operation of the digital product passport shall comply with the following essential requirements:(a)digital product passports shall be fully interoperable with other digital product passports as regards the technical, semantic and organisational aspects of end-to-end communication and data transfer;(b)a recipient of the digital product passport shall have easy access, free of charge, to it based on the recipient’s respective access rights in the construction digital product passport system;(c)the data included in the digital product passport shall be stored as specified in the construction digital product passport system referred to in Article 75;(d)if the data included in the digital product passport is stored or otherwise processed by authorised operators or digital product passport service providers, they shall not be allowed to sell, reuse or process such data, in whole or in part, beyond what is necessary for the provision of the relevant storing or processing services, unless this is specifically agreed with the economic operator placing the product on the market;(e)the digital product passport shall remain available for the period specified in Article 76(2), point (h), including after an insolvency, a liquidation or a cessation of activity in the Union of the economic operator that created the digital product passport, and shall fulfil the conditions established in accordance with Article 75(2), point (f), as regards the obligation to establish a back-up system;(f)the right to access and to introduce, modify or update information in the digital product passport shall be restricted to the access rights specified in the construction digital product passport system;(g)protection of information that constitutes trade secrets within the meaning of Article 2(1) Directive (EU) 2016/943 of the European Parliament and of the CouncilDirective (EU) 2016/943 of the European Parliament and of the Council of 8 June 2016 on the protection of undisclosed know-how and business information (trade secrets) against their unlawful acquisition, use and disclosure (OJ L 157, 15.6.2016, p. 1). or intellectual property rights shall be ensured;(h)data authentication, reliability and integrity shall be ensured;(i)digital product passports shall be designed and operated so that a high level of security and privacy is ensured and fraud is avoided.
Article 79Unique identifiers and digital product passport registry1.Article 12 of Regulation (EU) 2024/1781 shall apply for the purposes of the implementation of this Regulation as regards unique identifiers and data carriers unless the delegated act referred to in Article 75(1) of this Regulation lays down more detailed or alternative rules related to those unique identifiers and data carriers, as referred to in Article 75(2)(h) of this Regulation.2.Article 13 of Regulation (EU) 2024/1781 shall apply for the purposes of the implementation of this Regulation as regards the digital product passport registry unless the delegated act referred to in Article 75(1) of this Regulation lays down more detailed or alternative rules related to that registry, as referred to in Article 75(2)(h) of this Regulation.3.Article 14 of Regulation (EU) 2024/1781 shall apply for the purposes of implementation of this Regulations as regards the web portal for information in the digital product passport.
Article 80Mandatory use and technical adaptation1.Six months after the entry into force of the delegated act referred to in Article 75(1), the system shall be fully operational and shall be fulfilling its intended objectives, including the functionalities provided for in Article 76. 18 months after the entry into force of the delegated act referred to in Article 75(1) the obligations established pursuant to Article 22(7) shall apply. The system may be used by manufacturers voluntarily in the interim period.2.The Commission is empowered to adopt delegated acts in accordance with Article 89 to amend this Regulation to:(a)further specify, add and remove functionalities referred to in Article 75(2) in order to adapt it to technical progress or to adapt it to the once-only principle in relation to information requirements in other Union law;(b)revise Articles 77(1) and 78 of this Regulation to ensure compatibility and interoperability with Regulation (EU) 2024/1781.
CHAPTER XIINTERNATIONAL COOPERATION
Article 81International cooperation1.For the purposes of the protection of health and safety of persons or of the environment, the Commission may, cooperate with authorities of third countries or international organisations in the field of application of this Regulation. Such cooperation may include:(a)the exchange of information on enforcement activities and measures related to safety and protection of the environment, including market surveillance;(b)the exchange of data of economic operators;(c)the exchange of information on assessment methods and product testing;(d)the exchange of information on product recalls, requests for corrective actions and other similar actions;(e)cooperation on scientific, technical, and regulatory matters, aiming to improve product safety or the protection of the environment and consumers;(f)the exchange of information on emerging issues of significant environmental, health and safety relevance;(g)the exchange of information on standardisation-related activities;(h)the exchange of officials.The exchange of information pursuant to this paragraph shall respect confidentiality rules and comply with applicable Union law.2.The information exchange referred to in paragraph 1 may take the form of:(a)a non-systematic exchange, in duly justified and specific cases; or(b)a systematic exchange, based on an administrative arrangement specifying the type of information to be exchanged and the modalities for the exchange.The Commission shall regularly inform Member States about the cooperation activities with third countries or international organisations that it undertakes pursuant to the first subparagraph.3.The Commission may adopt implementing acts, giving authorities of selected third countries that voluntarily apply this Regulation, or that have regulatory systems for construction products similar to this Regulation, access to or the right to fully participate in one or more of the following:(a)the information and communication system established in accordance with Article 71(1);(b)the construction digital product passport system set up in accordance with Article 75;(c)the training events organised in accordance with Article 73(2).Access to the systems and events referred to in the first subparagraph shall be granted on condition that the third country concerned commits to act against economic operators that infringe this Regulation from their territory, and to ensure confidentiality.Full participation in the systems referred to in Articles 71 and 75 may only be granted where agreements between the European Union and third countries so provide. Such participation may be offered to third countries provided that the third country’s legislation is aligned with this Regulation and third country competent national authorities recognise certificates issued by notified bodies or European technical assessments in accordance with this Regulation. Such participation shall be subject to the fulfilment of the same obligations as those which apply to Member States under this Regulation, including notification and follow-up obligations.The implementing acts referred to in the first subparagraph of this paragraph shall be adopted in accordance with the advisory procedure referred to in Article 90(2).4.Any information exchange under this Article, to the extent it involves personal data, shall be carried out in accordance with Union data protection rules. If no adequacy decision pursuant to Article 45 of Regulation (EU) 2016/679 has been adopted by the Commission in respect of the third country or international organisation concerned, the information exchange shall exclude personal data. If an adequacy decision for the third country or international organisation has been adopted, the information exchange with that third country or international organisation may contain personal data falling within the scope of the adequacy decision but only to the extent that such exchange is necessary for the sole purpose of the protection of health and safety of persons or of the environment.
CHAPTER XIIINCENTIVES AND PUBLIC PROCUREMENT
Article 82Member State incentives for construction productsWhere Member States provide incentives for a product category for which the performance is expressed as a class of performance referred to in Article 5(5) or as a class included in environmental sustainability labelling referred to in Article 22(9), those incentives shall be targeted at the highest two classes of performance.Where classes of performance are defined in relation to more than one sustainability parameter, it shall be indicated in relation to which parameter this Article should be implemented.When doing so, the Commission shall take into account the following criteria:(a)the number of products in each class of performance; and(b)the need to ensure the affordability of the products meeting those requirements, in order to avoid significant negative impacts on consumers.
Article 83Green public procurement1.The Commission shall adopt delegated acts in accordance with Article 89 to supplement this Regulation by specifying mandatory minimum environmental sustainability requirements for construction products.2.For procurement procedures falling within the scope of Directives 2014/24/EUDirective 2014/24/EU of the European Parliament and of the Council of 26 February 2014 on public procurement and repealing Directive 2004/18/EC (OJ L 94, 28.3.2014, p. 65). or 2014/25/EUDirective 2014/25/EU of the European Parliament and of the Council of 26 February 2014 on procurement by entities operating in the water, energy, transport and postal services sectors and repealing Directive 2004/17/EC (OJ L 94, 28.3.2014, p. 243). of the European Parliament and of the Council, where contracts require minimum environmental sustainability performance for construction products as regards their essential characteristics covered by harmonised technical specifications, contracting authorities and contracting entities shall apply the mandatory minimum environmental sustainability requirements laid down in the delegated acts referred to in paragraph 1.This shall not prevent contracting authorities and contracting entities from establishing:(a)more ambitious environmental sustainability requirements related to essential characteristics referred in the first subparagraph; or(b)additional environmental sustainability requirements related to other essential characteristics than those referred in the first subparagraph.3.Member States and the Commission shall provide technical assistance and advice to contracting authorities and contracting entities in charge of public procurement on how to comply with mandatory minimum environmental sustainability requirements laid down in the delegated acts referred to in paragraph 1.4.Mandatory minimum environmental sustainability requirements laid down in the delegated acts referred to in paragraph 1 for public contracts awarded by contracting authorities or contracting entities may, as appropriate to the product family or product category concerned, take the form of:(a)"technical specifications" within the meaning of Article 42 of Directive 2014/24/EU and Article 60 of Directive 2014/25/EU;(b)"selection criteria" within the meaning of Article 58 of Directive 2014/24/EU and Article 80 of Directive 2014/25/EU;(c)"conditions for performance of contracts" within the meaning of Article 70 of Directive 2014/24/EU and Article 87 of Directive 2014/25/EU;(d)"contract award criteria" within the meaning of Article 67 of Directive 2014/24/EU and of Article 82 of Directive 2014/25/EU.5.When establishing mandatory minimum environmental sustainability requirements pursuant to paragraph 1 for public contracts, the Commission shall, in line with paragraphs 13 and 28 of the Interinstitutional Agreement of 13 April 2016 on Better Law-Making, consult experts designated by each Member State and relevant stakeholders, carry out an impact assessment and take into account at least the following criteria:(a)the value and volume of public contracts awarded for the product family or product category concerned;(b)the environmental benefits resulting from the uptake of products in the highest two classes of performance;(c)the need to ensure sufficient demand for more environmentally sustainable products;(d)the economic feasibility, for contracting authorities or contracting entities, of buying more environmentally sustainable products, without entailing disproportionate costs, and the availability of those products on the market;(e)the market situation at Union level of the relevant product family or product category;(f)the effects of the requirements on competition;(g)the impact on, and needs of, SMEs;(h)the Members States’ regulatory needs and different climate conditions.The first impact assessment shall be launched by the Commission by 31 December 2026.6.Contracting authorities and contracting entities may on an exceptional basis decide not to apply paragraph 2 of this Article where, after preliminary market consultation in line with Article 40 of Directive 2014/24/EU and Article 58 of Directive 2014/25/EU, it was found that:(a)the required construction product can only be supplied by a specific economic operator, and no reasonable alternative or substitute exists;(b)no suitable tenders or no suitable requests to participate have been submitted in response to a previous public procurement procedure; or(c)the application of paragraph 1 or the incorporation of the required construction product in construction works would oblige that contracting authority or contracting entity to incur disproportionate costs, or would result in incompatibility or technical difficulties.Contracting authorities and contracting entities may presume that estimated contract value differences above 10 %, based on objective and transparent data, are disproportionate.When contracting authorities and contracting entities use the derogation in this paragraph, the procurement procedure cannot be considered to be environmentally sustainable in relation to the construction products to which the exceptions have been applied.Every three years, Member States shall report to the Commission about the use of this paragraph, in accordance with Article 83 of Directive 2014/24/EU.This paragraph shall be without prejudice to the possibility of excluding abnormally low tenders under Article 69 of Directive 2014/24/EU and Article 84 of Directive 2014/25/EU.7.The EU Ecolabel and other national or regional EN ISO 14024 type I ecolabelling schemes officially recognised in accordance with Article 11 of Regulation (EC) No 66/2010 of the European Parliament and of the CouncilRegulation (EC) No 66/2010 of the European Parliament and of the Council of 25 November 2009 on the EU Ecolabel (OJ L 27, 30.1.2010, p. 1). may be used to demonstrate compliance with the minimum environmental sustainability requirements where such label complies with the requirements set out in Article 19 of this Regulation.
CHAPTER XIIIREGULATORY STATUS OF PRODUCTS
Article 84Regulatory status of productsUpon a duly substantiated request of a Member State or on its own initiative, the Commission may adopt implementing acts, determining whether or not a specific item, or category of items is a product within the meaning of this Regulation.Those implementing acts shall be adopted in accordance with the examination procedure referred to in Article 90(3).
CHAPTER XIVEMERGENCY PROCEDURES
Article 85Application of emergency procedures1.Articles 86 to 88 of this Regulation shall apply only if the Commission has adopted an implementing act pursuant to Article 28 of Regulation (EU) 2024/2747 with respect to construction products covered by this Regulation.2.Articles 86 to 88 of this Regulation shall apply only to construction products, which have been designated as crisis-relevant goods pursuant to Article 18(4) of Regulation (EU) 2024/2747.3.This Chapter, except as regards the power of the Commission referred to in Article 87(7) of this Regulation, shall apply only during the internal market emergency mode that has been activated in accordance with Article 18 of Regulation (EU) 2024/2747.4.The Commission may adopt implementing acts regarding the corrective or restrictive actions to be taken, the procedures to be followed and the specific labelling and traceability requirements with respect to construction products placed on the market in accordance with Articles 86 and 87. Those implementing acts shall be adopted in accordance with the examination procedure referred to in Article 90(3).
Article 86Prioritisation of the assessment and verification of crisis-relevant construction products1.This Article applies to construction products listed in the implementing act referred to in Article 85(1), that are subject to third-party tasks of notified bodies related to the assessment and verification of construction products, in accordance with Article 10(1).2.The notified bodies shall make best efforts to process as a matter of priority requests for third-party tasks related to the assessment and verification of construction products referred to in paragraph 1, irrespective of whether those requests have been lodged before or after the activation of the emergency procedures pursuant to Article 85.3.The prioritisation of requests for third-party tasks related to the assessment and verification of construction products pursuant to paragraph 2 shall not result in additional disproportionate costs for the manufacturers who have lodged those requests.4.The notified bodies shall make reasonable efforts to increase their respective assessment and verification capacities regarding construction products referred to in paragraph 1 in respect of which they have been notified.
Article 87Assessment and declaration of performance based on standards and common specifications1.Where construction products have been designated as crisis-relevant goods, the Commission is empowered to adopt implementing acts, listing appropriate standards or establishing common specifications to cover the methods and the criteria for assessing the performance of those products in relation to their essential characteristics in the following cases:(a)where there are no performance harmonised standards and no implementing acts adopted in accordance with Article 6(1) that cover the relevant methods and criteria for assessing the performance of those products in relation to their essential characteristics and no such standards or acts are expected to be adopted within a reasonable period; or(b)where severe disruptions to the functioning of the internal market, which led to the activation of the internal market emergency mode in accordance with Article 18 of Regulation (EU) 2024/2747, significantly restrict the possibilities of manufacturers to make use of performance harmonised standards or implementing acts adopted in accordance with Article 6(1) of this Regulation that provide the relevant methods and criteria for assessing the performance of those products in relation to their essential characteristics.2.The implementing acts referred to in paragraph 1 shall set out the most appropriate alternative technical solution for the purposes of providing assessment and declaration of performance in accordance with paragraph 5. To that end, the references of European standards or references of relevant applicable international or national standards may be published in those implementing acts or, if there is no European standard or no relevant applicable international or national standard, common specifications may be established by those implementing acts.3.The implementing acts referred to in paragraph 1 of this Article shall be adopted in accordance with the examination procedure referred to in Article 90(3) and shall apply until the last day of the period during which the internal market emergency mode is activated, unless those implementing acts are amended or repealed in accordance with paragraph 7 of this Article.4.Before preparing the draft implementing act referred to in paragraph 1 of this Article, the Commission shall inform the committee referred to in Article 22 of Regulation (EU) No 1025/2012 that it considers that the conditions in paragraph 1 of this Article have been fulfilled. When preparing that draft implementing act, the Commission shall take into account the views of the CPR Acquis Expert Group and shall duly consult all relevant stakeholders.5.Without prejudice to Articles 13 and 15, the methods and the criteria provided in the standards or common specifications referred to in paragraph 1 of this Article, or parts thereof, may be used for assessing and declaring the performance of construction products covered by those standards or common specifications in relation to their essential characteristics. From the day following the expiry or deactivation of the internal market emergency mode it shall no longer be possible to draw up declarations of performance and conformity based on the standards or the common specifications referred to in the implementing act referred to in paragraph 1 of this Article.6.By way of derogation from Article 85(3), unless there is sufficient reason to believe that construction products covered by the standards or common specifications referred to in paragraph 1 of this Article present a risk to the health or safety of persons or fail to achieve the declared performance, the declarations of performance and conformity of construction products which have been placed on the market in compliance with those standards or common specifications shall remain valid after the expiry or repeal of an implementing act adopted pursuant to paragraph 3 of this Article and after the expiry or deactivation of the internal market emergency mode.7.Where a Member State considers that a standard or common specification as referred to in paragraph 1 is incorrect in terms of methods and criteria for the assessment of performance in relation to essential characteristics, it shall inform the Commission thereof by submitting a detailed explanation. The Commission shall assess that detailed explanation and, may, where appropriate, amend or repeal the implementing act listing the standard or establishing the common specification in question.
Article 88Prioritisation of market surveillance activities and mutual assistance among authorities1.Member States shall prioritise the market surveillance activities for construction products listed in the implementing act referred to in Article 85(1) of this Regulation. The Commission shall facilitate coordination of such prioritisation efforts through the Union Product Compliance Network established under Article 29 of Regulation (EU) 2019/1020.2.The market surveillance authorities of the Member States shall ensure that best efforts are made to provide assistance to other market surveillance authorities during an internal market emergency mode, including by mobilising and dispatching expert teams to temporarily reinforce the staff of market surveillance authorities requesting assistance or by providing logistical support, such as the reinforcement of the testing capacity for construction products listed in the implementing act referred to in Article 85(1).
CHAPTER XVFINAL PROVISIONS
Article 89Delegated acts1.The power to adopt delegated acts is conferred on the Commission subject to the conditions laid down in this Article.2.The power to adopt delegated acts referred to in Article 4(7), Article 5(5), (6) and (10), Article 7(1), and (8), Article 9(3) and (4), Article 10(2),and (4), Article 12, Article 15(5), Article 22(8) and (9), Article 32(5), Article 75(1), Article 80(2) and Article 83(1)shall be conferred on the Commission for a period of five years from 7 January 2025. The Commission shall draw up a report in respect of the delegation of power not later than nine months before the end of the five-year period. The delegation of power shall be tacitly extended for periods of an identical duration, unless the European Parliament or the Council opposes such extension not later than three months before the end of each period.3.The delegation of powers referred to in Article 4(7), Article 5(5), (6) and (10), Article 7(1) and (8), Article 9(3) and (4), Article 10(2) and (4), Article 12, Article 15(5), Article 22(8) and (9), Article 32(5), Article 75(1), Article 80(2) and Article 83(1) may be revoked at any time by the European Parliament or by the Council. A decision to revoke shall put an end to the delegation of the power specified in that decision. It shall take effect the day following the publication of the decision in the Official Journal of the European Union or at a later date specified therein. It shall not affect the validity of any delegated acts already in force.4.Before adopting a delegated act, the Commission shall consult experts designated by each Member State in accordance with the principles laid down in the Interinstitutional Agreement of 13 April 2016 on Better Law-Making.5.As soon as it adopts a delegated act, the Commission shall notify it simultaneously to the European Parliament and to the Council.6.A delegated act adopted pursuant to Article 4(7), Article 5(5), (6) or (10), Article 7(1) or (8), Article 9(3) or (4), Article 10(2) or (4), Article 12, Article 15(5), Article 22(8) or (9), Article 32(5), Article 75(1), Article 80(2) or Article 83(1) shall enter into force only if no objection has been expressed either by the European Parliament or the Council within a period of two months of notification of that act to the European Parliament and the Council or if, before the expiry of that period, the European Parliament and the Council have both informed the Commission that they will not object. That period shall be extended by two months at the initiative of the European Parliament or of the Council.
Article 90Committee procedure1.The Commission shall be assisted by the Committee on Construction Products. This committee shall be a committee within the meaning of Regulation (EU) No 182/2011.2.Where reference is made to this paragraph, Article 4 of Regulation (EU) No 182/2011 shall apply.3.Where reference is made to this paragraph, Article 5 of Regulation (EU) No 182/2011 shall apply.4.Where reference is made to this paragraph, Article 8 of Regulation (EU) No 182/2011, in conjunction with Article 5 thereof, shall apply.
Article 91Electronic applications, decisions, documentation and information1.All applications from or to notified bodies or TABs and decisions made by these bodies made in accordance with this Regulation can be provided on paper or in a commonly used electronic format provided that the signature complies with the requirements of Regulation (EU) No 910/2014 and the signing person has been entrusted with the task of representing the body or economic operator, in accordance with the law of the Member States or Union law respectively.2.All information obligations under this Regulation may, unless otherwise stated, be satisfied by electronic means. Where the information is provided by electronic means, the information shall be issued in a commonly readable electronic format that enables the recipient to download and print that information.When the obligation is established in accordance with Article 22(7), economic operators shall fulfil information obligations related to documents referred to in Article 76(2) by providing the digital product passport.Declaration of performance and conformity as well as general product information, instructions for use and safety information shall be provided in paper format, free of charge, if requested by the end-user at the time of purchase.
Article 92PenaltiesMember States shall lay down the rules on penalties applicable to instances of non-compliance with this Regulation and shall take all measures necessary to ensure that these rules are implemented. The penalties provided for shall be effective, proportionate and dissuasive. Member States shall, by 8 December 2026, notify the Commission of those rules and of those measures and thereafter shall notify it, without delay, of any subsequent amendment affecting them.
Article 93EvaluationNo later than 9 January 2033 and at least every six years thereafter, the Commission shall carry out an evaluation of this Regulation and of its contribution to the functioning of the internal market and the improvement of the environmental sustainability of products and construction works and built environment. That evaluation shall, inter alia, assess the correlation of this Regulation with Regulation (EU) 2024/1781 and the potential environmental and economic benefits and the impact of extended producer responsibility of manufacturers of certain construction products and of the regain of ownership of surplus and unsold products at Union level. The Commission shall also evaluate the effect of the application of this Regulation on the state of the market for different categories of used products. The Commission shall evaluate whether the penalties applied by the Member States are effective and whether they create fragmentation in the internal market. The Commission shall, if necessary, suggest how to harmonise those penalties.The Commission shall present a report on the main findings to the European Parliament, the Council, the European Economic and Social Committee, and the Committee of the Regions. Member States shall provide the Commission with the information necessary for the preparation of that report.Where appropriate, the report shall be accompanied by a legislative proposal for the amendment of the relevant provisions of this Regulation.
Article 94RepealRegulation (EU) No 305/2011 is repealed with effect from 8 January 2026, with the exception of Article 2, Articles 4 to 9, Articles 11 to 18, Articles 27 and 28, Articles 36 to 40, Articles 47 to 49, Articles 52 and 53, Article 55, Articles 60 to 64 of that Regulation and Annexes III and V thereto which are repealed with effect from 8 January 2040.References to the repealed Regulation shall be construed as references to this Regulation and shall be read in accordance with the correlation table in Annex XI to this Regulation.
Article 95Derogations and transitional provisions1.Product contact points for construction designated under Regulation (EU) No 305/2011 shall be deemed to have been designated under this Regulation as well.2.TABs and notified bodies that are designated or notified under Regulation (EU) No 305/2011 shall be deemed to have been designated or notified under this Regulation as well. However, they shall be assessed and designated anew by the designating Member States in accordance with their periodic re-assessment cycle and at the latest by 8 January 2030. The objection procedure set out in Article 51(5) of this Regulation shall apply.3.Harmonised standards the references of which are included in the list published in accordance with Article 17(5) of Regulation (EU) No 305/2011 that are in force on 8 January 2026 shall remain valid under Regulation (EU) No 305/2011 until they are withdrawn by the Commission or otherwise repealed.4.European assessment documents, the references of which are included in the list published in accordance with Article 22 of Regulation (EU) No 305/2011 by 8 January 2026, shall remain valid until 9 January 2031, unless they have expired for other reasons. Products shall not be placed on the market on the basis of European technical assessments issued in accordance with these European assessment documents after 9 January 2036.5.When a harmonised technical specification adopted in accordance with Article 5(8) or Article 6(1) of this Regulation covers the same product and the same intended use as a European assessment document, the reference of which is included in the list published in accordance with Article 22 of Regulation (EU) No 305/2011, the European assessment document shall no longer be used for the purposes of this Regulation and products shall not be placed on the market on the basis of European technical assessments issued in accordance with this European assessment document.6.European technical assessments issued pursuant to European assessment documents the references of which are not included in the list published in accordance with Article 22 of Regulation (EU) No 305/2011 by 8 January 2026 shall be treated as European technical assessment requests under this Regulation. The administrative transfer shall be done at no cost for the manufacturer.7.Certificates, test reports and European technical assessments issued under Regulation (EU) No 305/2011 may be used as the technical basis to demonstrate a product’s compliance with this Regulation in cases where the product type corresponds to a product type under this Regulation and the requirements and assessment methods are valid in the light of the applicable harmonised technical specification or European assessment document. The recognition of such documents shall be possible under the conditions set out in Article 62 of this Regulation, applied mutatis mutandis.8.Article 2, Articles 4 to 9, Articles 11 to 18, Articles 27 and 28, Articles 36 to 40, Articles 47 to 49, Articles 52 and 53, Article 55 and Articles 60 to 64 of Regulation (EU) No 305/2011 shall only apply to products covered by standards referred to in paragraph 3 of this Article or to products covered by European assessment documents referred to in paragraph 4 of this Article.For the purposes of Article 5(7), Article 6(1), and Article 31(2) of this Regulation, harmonised standards the references of which are included in the list published in accordance with Article 17(5) of Regulation (EU) No 305/2011 and which have not been withdrawn shall be treated as performance harmonised standards.9.The requirements and obligations of economic operators set out in Chapters I, II and III shall only be applicable to a certain product family or product category within such a family from one year after the date of adoption of an implementing act referred to in Article 5(8) making a harmonised standard mandatory or an implementing act referred to in Article 6(1), covering that product family or product category, unless a later application date has been specified in the implementing act. However, economic operators may choose to apply those harmonised technical specifications as from their entry into force by undergoing the procedure leading to a declaration of performance and conformity.10.Within one year following the date of application of requirements and obligations in relation to a certain product family or product category as set out in paragraph 9 of this Article, the Commission shall withdraw from the Official Journal of the European Union references of harmonised standards and European assessment documents or parts thereof published there in accordance with Articles 17(5) and 22 of Regulation (EU) No 305/2011 when they cover the same respective product family or product category.
Article 96Entry into forceThis Regulation shall enter into force on the twentieth day following its publication in the Official Journal of the European Union.It shall apply as from 8 January 2026, with the exception of Articles 1 to 4, Article 5(1) to (7), Article 7(1), Article 9, Article 10, Article 12(1) first subparagraph, Article 16(3), Article 37(4), Article 63, Article 89 and Article 90 and Annexes I, II, III, IV, VII, IX and X, which shall apply from 7 January 2025, and of Article 92, which shall apply from 8 January 2027.
This Regulation shall be binding in its entirety and directly applicable in all Member States.Done at Strasbourg, 27 November 2024.For the European ParliamentThe PresidentR. MetsolaFor the CouncilThe PresidentBóka J.ANNEX IBasic requirements for construction worksThe following list of basic requirements for construction works shall be taken as the basis for the identification of essential characteristics of products and for the preparation of standardisation requests, harmonised technical specifications and European assessment documents.Those basic requirements for construction works do not constitute obligations incumbent upon economic operators or Member States.The intended life span related to basic requirements for construction works shall take into account the likely impact of climate change.1.Structural integrity of construction worksThe construction works, and their relevant parts, shall be designed, constructed, used, maintained and deconstructed or demolished in such a way that all relevant loads and any combinations of them are sustained and transmitted into the ground safely and without causing deflections or deformations of any part of the construction works, or movement of the ground as to impair the durability, structural resistance, serviceability and robustness of the construction works.The structure and structural elements of construction works shall be designed, manufactured, constructed, maintained and deconstructed or demolished in such a way that they meet the following requirements:(a)they are durable for their intended life span (durability requirement);(b)they are capable of withstanding all actions and influences likely to occur during construction, use and deconstruction or demolition with an appropriate degree of reliability and in a cost-effective way (structural resistance requirement) and it shall not:(i)collapse;(ii)deform to an inadmissible degree;(iii)damage other parts of the construction works, fittings or installed equipment as a result of major deformation of the load-bearing construction;(c)they remain within their specified service requirements during their intended life span with appropriate degrees of reliability and in an economic way (serviceability requirement);(d)they maintain their integrity appropriately when faced with adverse events, including earthquake, explosion, fire, impact or consequences of human errors, to an extent disproportionate to the original cause (robustness requirement).2.Fire safety of construction worksThe construction works and the relevant parts of them shall be designed, constructed, used, maintained and deconstructed or demolished in such a way that an outbreak of fire is appropriately prevented, including through adequate usage of detectors and alarms. The fire and smoke shall be contained and controlled, and the occupants of the construction works shall be protected against fire and smoke. Appropriate arrangements shall have been made to ensure safe escape from and evacuation of the construction works for all its occupants.The construction works and any part of them shall be designed, constructed, used and maintained in such a way that they meet the following requirements in the case of a fire:(a)the load-bearing capacity of the construction works is maintained for a specific period of time to give occupants time to leave the building;(b)the rescue and emergency services’ access is ensured and there are appropriate means to facilitate their work;(c)the generation and spread of fire and smoke is controlled and limited;(d)the spread of the fire and smoke to the adjacent construction works is limited;(e)the safety of rescue and emergency services is taken into consideration.3.Protection against adverse hygiene and health impacts related to construction worksThe construction works and any part of them shall be designed, constructed, used, maintained and deconstructed or demolished in such a way that they, throughout their life cycle, do not adversely affect the hygiene or health and safety of construction workers, occupants, visitors or neighbours as a result of any of the following:(a)the emissions of hazardous substances, volatile organic compounds or hazardous particles, including microplastics, into indoor air;(b)the emission of hazardous radiation into the indoor environment;(c)the release of hazardous substances into drinking water or substances which have an otherwise negative impact on drinking water;(d)the passage of moisture to the interior of the building;(e)faulty discharge of waste water, emission of flue gases or faulty disposal of solid or liquid waste into the indoor environment.4.Safety and accessibility of construction worksThe construction works and any part of them shall be designed, constructed, used, maintained and deconstructed or demolished in such a way that, throughout their life cycle, they do not present unacceptable risks of accidents or damage in service or in operation, including slipping, falling, collision, burns, electrocution and injury from falling or braking parts caused by external factors like extreme weather conditions or explosions.In particular, construction works shall be designed and built taking into consideration accessibility and use for disabled persons and persons with limited mobility or orientation.5.Resistance to the passage of sound and acoustic properties of construction worksThe construction works and any part of them shall be designed, constructed, used, maintained and deconstructed or demolished in such a way that they provide, throughout their life cycle, reasonable protection against adverse sound load through air or materials from other parts of the same construction work or sources outside its structure. That protection shall ensure that that sound load:(a)does not create immediate or chronic risks for the human health;(b)allows occupants and people nearby to sleep, rest and engage in their normal activities in satisfactory conditions.The construction works and any part of them shall be designed, constructed, used and maintained in such a way that they provide sufficient sound absorption and reflection where these acoustic properties are required.6.Energy efficiency and thermal performance of construction worksThe construction works, including automated processes within them, and their heating, cooling, lighting and ventilation installations shall be designed, built, and maintained in such a way that the amount of energy they require during their use phase shall be low, when account is taken of:(a)the target for nearly zero energy buildings and zero-emissions buildings in the Union;(b)the outdoor climatic conditions;(c)the indoor climate conditions.7.Emissions into the outdoor environment of construction worksThe construction works and any part of them shall be designed, constructed, used, maintained and deconstructed or demolished in such a way that, throughout their life cycle, they are not a risk to the outdoor environment, as a result of any of the following:(a)the release of hazardous substances, microplastics, or radiation into air, ground water, marine or surface waters or soil;(b)faulty discharge of waste water, emission of flue gases or faulty disposal of solid or liquid waste to the outdoor environment;(c)damage to the building, including damage through the transport of water-borne contaminants to the foundations of the building;(d)the release of greenhouse gas emissions into the atmosphere.8.Sustainable use of natural resources of construction worksThe construction works and any part of them shall be designed, constructed, used, maintained and deconstructed or demolished in such a way that, throughout their life cycle, the use of natural resources is sustainable and ensures the following:(a)the maximisation of the resource efficient use of raw and secondary materials of high environmental sustainability;(b)the minimisation of the overall amount of raw materials used;(c)the minimisation of the overall amount of embodied energy;(d)the minimisation of the waste generated;(e)the minimisation of the overall use of drinking and service water;(f)the maximisation of the reuse or recyclability of the construction works, in part or in whole, and of their materials after deconstruction or demolition;(g)the ease of deconstruction.ANNEX IIPredetermined environmental essential characteristicsHarmonised technical specifications and European assessment documents shall cover the following list of predetermined environmental essential characteristics related to the life cycle assessment of a product:(a)climate change effects – total;(b)climate change effects – fossil fuels;(c)climate change effects – biogenic;(d)climate change effects – land use and land use change;(e)ozone depletion;(f)acidification potential;(g)eutrophication aquatic freshwater;(h)eutrophication aquatic marine;(i)eutrophication terrestrial;(j)photochemical ozone;(k)abiotic depletion – minerals, metals;(l)abiotic depletion – fossil fuels;(m)water use;(n)particulate matter;(o)ionising radiation, human health;(p)eco-toxicity, freshwater;(q)human toxicity, cancer;(r)human toxicity, non-cancer;(s)land use related impacts.Harmonised technical specifications shall also cover to the extent possible the predetermined environmental essential characteristic of capability to temporarily bind carbon and of other carbon removals.ANNEX IIIProduct requirements1.Product requirements ensuring appropriate functioning and performance1.1.Harmonised technical specifications adopted in accordance with Article 7(1) may, as appropriate for the products that they cover, specify that products shall be designed, manufactured and packaged in such a way that, over the product’s life cycle, one or more of the following functional and performance requirements are addressed in accordance with the state of the art and to the extent not covered by other Union legal acts:(a)the intended purpose is effectively and reliably fulfilled;(b)the fulfilment of the declared performance is not impaired;(c)the fulfilment of the safety and environmental requirements set out in accordance with points 2.1 and 3.1 is not impaired;(d)the functionality of the products is maintained.1.2.Voluntary harmonised standards for product requirements referred to in Article 7(3) and common specifications conferring a presumption of conformity shall set out how any requirements in accordance with point 1.1 can be fulfilled, by, for example, the following:(a)the use of specific materials which can be specified also in terms of their chemical composition;(b)the specific dimensions and shapes of products or their components;(c)the use of certain components which can be specified also in terms of materials, dimensions and shapes;(d)the use of certain accessories and requirements for them;(e)the ease of installation and deinstallation;(f)the ease of maintenance or the lack of maintenance required for the expected life span;(g)the characteristics of the product, including its cleanability, scratch resistance and break resistance, under usual operation conditions.1.3.When specifying the functionality and performance product requirements, harmonised technical specifications may differentiate them on the basis of their classes of performance.2.Product safety requirementsSafety relates to professionals (workers) and non-professionals (consumers, occupants), while they transport, install, maintain, use or dismantle the product, as well as while they treat the product for its end of life phase or its reuse or recycling.2.1.Harmonised technical specifications established by delegated acts referred to in Article 7(1) may, as appropriate for the products they cover, specify that products shall be designed, manufactured, and packaged in such a way that one or more of the following inherent product safety risks are, over the product’s life cycle, addressed in accordance with the state of the art and to the extent they are not covered by other Union legal acts:(a)chemical risks due to leaking or leaching;(b)the risk of unbalanced composition in terms of substances resulting in flawed, safety-relevant functioning of products;(c)mechanical risks;(d)mechanical failure;(e)physical failure;(f)risks of electric failure;(g)risks linked to electricity supply breakdown;(h)risks linked to unintended charge or discharge of electricity;(i)risks linked to software failure;(j)risks of software manipulation;(k)risks of incompatibility of substances or materials;(l)risks linked to the incompatibility of different items, at least one of them being a product;(m)the risk of not performing as intended, where the performance is safety relevant;(n)the risk of misunderstanding instructions for use in a field affecting health and safety;(o)the risk of unintended inappropriate installation or use;(p)the risk of intended inappropriate use.2.2.Voluntary harmonised standards and common specifications conferring a presumption of conformity shall set out how any requirements in accordance with point 2.1 can be fulfilled, by, for example, the following:(a)defining the state of the art of possible risk reduction with regard to the respective product category, including the risk of incompatibility of different items, at least one of them being a product;(b)providing technical solutions that avoid safety-related risks; or(c)where risk avoidance is not possible, reducing and mitigating risks by addressing them through warnings on the product, its packaging and in instructions for use.2.3.When specifying the product safety requirements, harmonised technical specifications may differentiate these on the basis of their classes of performance.3.Product environmental requirementsEnvironment relates to the extraction and manufacturing of the materials, the manufacturing of the product, the transport of materials and products, its maintenance, its potential to remain as long as possible within a circular economy and its end of life phase.3.1.Harmonised technical specifications established by delegated acts referred to in Article 7(1) may, as appropriate for the products they cover, specify that products shall be designed, manufactured, and packaged in such a way that one or more of the following inherent product environmental aspects are, over the product’s life cycle, addressed wherever possible without safety loss or by outweighing negative environmental impact, and to the extent not covered by other Union legal acts:(a)maximising durability and reliability of the product or its components as expressed through a product’s technical lifetime indication of real use information on the product, resistance to stress or ageing mechanisms and in terms of the expected average life span, the minimum life span under worst but still realistic conditions, and in terms of the minimum life span requirements and prevention of premature obsolescence;(b)minimising life-cycle greenhouse gas emissions;(c)maximising reused, recycled and by-product content;(d)the selection of safe, sustainable-by-design and environmentally benign substances;(e)energy use and energy efficiency;(f)resource efficiency;(g)modularity;(h)identifying which product or parts thereof can be reused after deinstallation (reusability), and in what quantities;(i)upgradability;(j)the ease of reparability during the expected life span, including compatibility with commonly available spare parts;(k)the ease of maintenance and refurbishment during the expected life span;(l)recyclability and the capability to be remanufactured;(m)the capability of different materials or substances to be separated and recovered during dismantling or recycling procedures;(n)sustainable sourcing;(o)minimising the packaging/product ratio;(p)amounts of waste generated, notably hazardous waste.3.2.Voluntary harmonised standards and common specifications conferring a presumption of conformity shall set out how any requirements in accordance with point 3.1 can be fulfilled by, for example, the following:(a)specifying what is the state of the art for addressing the environmental aspects with regard to the respective product category, including the minimum recycled content, whole life cycle greenhouse gas emissions, resource efficiency and reusability;(b)providing technical solutions which avoid negative environmental effects and risks, including the generation of waste materials, or, where avoidance is not possible, reducing and mitigating negative effects and risks by addressing them through warnings on the product, its packaging and in instructions for use.3.3.When specifying the product environmental requirements, harmonised technical specifications may differentiate them on the basis of their classes of performance.ANNEX IVGeneral product information, instructions for use and safety information1.General product information1.1.Product identification: unique identification code of the product type.1.2.Product description:(a)declared uses;(b)intended users;(c)conditions of uses;(d)estimated average and minimum service life span for declared use (durability);(e)main materials used.1.3.Contact details of the manufacturer or the authorised representative:(a)name;(b)postal address;(c)telephone;(d)email address;(e)website, where available.1.4.Where different from point 1.3, contact details of the manufacturer or the authorised representative dealing with:(a)information on installation, maintenance, use, deconstruction and demolition;(b)information on risks;(c)information in the event of product failure.1.5.Contact details of the product contact point for construction in the Member State in which the product is made available.2.Instructions for use and safety information2.1.Safety during transport, installation, deinstallation, maintenance, deconstruction and demolition:(a)potential risks of the product and any reasonably foreseeable misuse thereof;(b)instructions for the assembly, installation and connection, including drawings, diagrams and, where relevant, the means of attachment to other products and parts of construction works;(c)instructions for operation and maintenance to be carried out safely, including the protective measures that should be taken during these operations;(d)if necessary, instructions for the training of the installers or operators;(e)information on what to do in the event of product failure or accidents.2.2.Compatibility and integration in systems or kits:(a)compatibility with other materials or products, regardless of whether they are covered by this Regulation or not;(b)electric and electro-magnetic compatibility;(c)software compatibility;(d)integration in systems or kits.2.3.Maintenance needs with a view to maintaining the performance of the product during its service life span:(a)description of the adjustment and maintenance operations that should be carried out by the users and the preventive maintenance measures that should be observed;(b)the type and frequency of the inspections and the maintenance required for reasons of safety and durability and, where appropriate, the parts subject to wear and the criteria for replacement;(c)information on what to do in the event of product failure or accident.2.4.Safety during use:(a)instructions on the protective measures to be taken by the user, including, where appropriate, the personal protective equipment to be provided;(b)instructions designed for the safe use of the product, including the protective measures that should be taken during its use;(c)information on what to do in the event of product failure or accident during use.2.5.Training and other requirements necessarily to be fulfilled for safe use.2.6.Risk mitigation possibilities going beyond points 2.1 to 2.5.2.7.Recommendations for a product’s:(a)repair;(b)deinstallation;(c)reuse;(d)remanufacturing;(e)recycling;(f)safe deposit.2.8.Where applicable, information on the performance of the product as measured in terms of its climate change effects – total, as referred to in point (a) of Annex II, and human toxicity, cancer, as referred to in point (q) of Annex II.3.The information provided on the elements listed in point 2 shall be enough, both in terms of quantity and quality, to enable potential purchasers to make informed decisions before proceeding with their purchase, including information on the necessary quantity, installation, use, maintenance, dismantling, reuse and recycling of the respective product. It may include all the drawings, diagrams, descriptions and explanations necessary for it to be understood.The information shall, as appropriate, take into account as far as possible the needs of designers, building authorities, construction professionals, building control authorities, consumers and other users, occupant and, use managers, as well as of maintenance professionals.4.Guidelines and technical details issued in accordance with Article 9(2) shall also recommend where the respective information is to be provided. That location shall be one where the information is least likely to be overlooked.ANNEX VDeclaration of performance and conformity referred to in Article 15Where a Declaration of Performance and Conformity is issued in relation to a product not subject to product requirements established by delegated acts referred to in Article 7(1), points 10 and 11(c) are omitted.Name of the ManufacturerDeclaration Code …Only one unique, unequivocal declaration code per product type shall be used, even where there are variants, variants being variations of the product type that do not influence performance or conformity of the product.Version No …Different versions may be issued, e.g. to correct mistakes or add complementary information.Date of that version …1.Product description(a)unique identification code of the product type and, where available, the batch or serial number;(b)product category as defined by harmonised technical specifications or European assessment documents;(c)declared uses of the product, within the scope of the applicable harmonised technical specification or European assessment document;(d)nominal dimensions or grading of the product;(e)key parts of the product, where applicable;(f)estimated average and minimum service life time for the declared use (durability);(g)variants, if any, and their descriptions;(h)in cases where the product has been previously installed in a construction work, the date and place of the latest deinstallation.2.Permalinks or data carriers as regards the following, unless the information is available in the digital product passport pursuant to Article 76:(a)the manufacturer’s product registrations in Union databases, if any;(b)information to be provided in accordance with Regulation (EC) No 1907/2006, where applicable;(c)general product information, instructions for use and safety information in accordance with Annex IV.3.Manufacturer:(a)name;(b)registered trade name;(c)registered place of business;(d)postal address;(e)telephone;(f)email address;(g)website.4.Authorised representative, where applicable:(a)name;(b)registered trade name;(c)registered place of business;(d)postal address;(e)telephone;(f)email address;(g)website.5.Notified body or bodies, where applicable:(a)name;(b)identification number;(c)registered trade name, where available;(d)registered place of business;(e)postal address;(f)telephone;(g)email address;(h)website.6.Technical Assessment Body ("TAB"), where applicable:(a)name;(b)identification number;(c)registered trade name, where available;(d)place of business;(e)postal address;(f)telephone;(g)email address;(h)website.7.Reference to certificates or validation reports issued by notified bodies and TABs.8.Technical reference documents:(a)harmonised technical specifications laying down essential characteristics applied (reference number and date of issue); or(b)European assessment document applied (reference number and date of issue) and European technical assessment issued (TAB, reference number and date of issue).9.Declared performances and sustainability characteristics:(a)the complete list of essential characteristics, as determined in the harmonised technical specification or European assessment document for the respective product category for which a performance is declared and the applicable assessment and verification system applicable to them;(b)the performance of the product, by calculated values, levels or classes, or in a description. Respective values, levels or classes shall be reproduced in the declaration of performance itself and thus cannot be expressed solely by inserting references to other documents. For essential characteristics where no performance is declared, the word "NULL" shall be inserted in the place for the declaration of the value. The performance of structural behaviour of a product may be expressed by referring to attached production documentation or structural design calculations;(c)the environmental sustainability expressed, for the applicable essential characteristics of the applicable life cycle modules, in accordance with Article 15(2);(d)reference to the version of the software used as provided by the Commission.10.Applicable product requirements specified by harmonised technical specifications, the applicable assessment and verification system applicable to them and the reference to the voluntary harmonised standard or common specifications or parts thereof applied including the date.Where applicable, information on the performance of the product measured in terms of its product requirements.11.Declarations:(a)the performance of the product identified above is in conformity with the set of declared performances referred to in point 9;(b)the sustainability data of the product identified above have been correctly calculated on the basis of the product category rules applicable to it;(c)the product identified above is in conformity with the requirements listed under point 10.Signed for and on behalf of the manufacturer by:[name, functionThe person signing must be authorised under national law to represent the manufacturer, either on the basis of a mandate, or by virtue of his or her role as a legal representative.]At [place]on [date of issue][signature]ANNEX VIProcedure for requesting European technical assessments and for adopting a European assessment document1.Request for a European technical assessment1.1.When a manufacturer makes a request for a European technical assessment to any TAB for a product, and after the manufacturer and the TAB ("responsible TAB") have signed an agreement of commercial secrecy and confidentiality, unless the manufacturer decides otherwise, the manufacturer shall submit to the responsible TAB a technical file describing the product, its use as foreseen by the manufacturer and details of the factory production control the manufacturer intends to apply;1.2.When a group of manufacturers or a manufacturers’ association (the "Group") makes a request for a European technical assessment, it shall address the request to the organisation of TABs that will propose to the Group a TAB to act as the responsible TAB. The Group can either accept the proposed TAB or ask the organisation of TABs to propose an alternative TAB. Once the Group has accepted the responsible TAB proposed by the organisation of TABs, the members of the Group shall sign a commercial secrecy and confidentiality agreement with that TAB, unless the Group decides otherwise, and the Group shall submit to the responsible TAB a technical file describing the product, its use as foreseen by the Group and details of the factory production control that the members of the Group intend to apply;1.3.In the absence of a request for a European technical assessment, when the Commission initiates the development of a European assessment document, it shall deliver to the organisation of TABs a technical file describing the product, its use and details to become applicable. The organisation of TABs shall, together with the Commission, agree on a TAB to act as the responsible TAB.2.ContractFor products referred to in Article 33(1), point (c), within 1 month from the reception of the technical file, in the cases referred to in points 1.1 and 1.2, a contract shall be concluded respectively between the manufacturer or the Group and the responsible TAB for the production of the European technical assessment, specifying the work programme for drawing up the European assessment document, including:(a)the organisation of work within the organisation of TABs;(b)the composition of the workgroup to be established within the organisation of TABs, designated for the product family in question; and(c)the coordination of TABs.In the case referred to in point 1.3, the responsible TAB shall submit to the Commission the work programme for drawing up the European assessment document with the same content and within the same deadline. Thereafter, the Commission shall have 30 working days to communicate to the responsible TAB its observations on the work programme, and the responsible TAB shall amend that work programme accordingly.3.Communication of work programmeIn the cases referred to in points 1.1 and 1.2, after agreement with the manufacturer and the Group respectively, the organisation of TABs shall inform the Commission of the work programme for drawing up the European assessment document and the schedule for its execution, indicating the assessment programme. That communication shall take place within three months of receipt of the request for a European technical assessment by a TAB, whereupon the TAB shall initiate the procedure laid down in points 1.1 and 1.2.In the case referred to in point 1.3, the organisation of TABs shall submit to the Commission the work programme for drawing up the European assessment document with the same content and within the same deadline as indicated in the previous subparagraph. The Commission shall then communicate to the organisation of TABs within 30 working days its observations on the work programme. After the responsible TAB and the organisation of TABs has been given the opportunity to comment, the responsible TAB shall amend the work programme accordingly.4.The draft European assessment documentThe organisation of TABs shall, by means of the working group coordinated by the responsible TAB, finalise a draft European assessment document which it shall communicate to the parties concerned within 6 months of the date the Commission was informed of the work programme in the cases referred to in points 1.1 and 1.2 or the date the Commission communicated to the responsible TAB its observations on the work programme in the case referred to in point 1.3.5.Commission ParticipationA Commission representative may participate, as an observer, in all the parts of the execution of the work programme. The Commission may request the organisation of TABs at any stage to abandon or modify the development of a certain European assessment document if the development is not in line with this Regulation or if the approach is not efficient or effective in terms of resources and final applicability. The Commission may request the organisation of TABs at any stage to merge parallel processes for the development of European assessment documents, or to split a single process in two, in order to increase the clarity of, or to ensure efficiency in, the development process or in the future application of the assessment document under consideration.Where the TABs involved do not agree on a European assessment document within the time limits provided, the organisation of TABs shall submit the matter to the Commission for resolution, including through instructions to the organisation of TABs on how to complete its work.6.Member States consultationIn the case referred to in point 1.3, the Commission shall inform Member States on the development of the European assessment document after the finalisation of the work programme for it. When requested, Member States may, where appropriate, participate in its execution. Observations from the Member States shall be communicated to, and shall be dealt with by, the Commission. The organisation of TABs shall be informed by the Commission of any change in the work programme, required and agreed to by the Commission, within the time frame given to the Commission for commenting on the work programme before starting the development of the European assessment document.7.Extension and delayAny delay in relation to the time limits set in points 1 to 4 of this Annex shall be reported by the working group to the organisation of TABs and to the Commission.If an extension of the time limits for developing the European assessment document can be justified, notably by the absence of a Commission decision on the applicable assessment and verification system for the product or by the need to develop a new test method, an extended time limit shall be set by the Commission.8.Amendments and adoption of a draft European assessment document8.1.In the cases referred to in points 1.1 and 1.2, the responsible TAB shall communicate the draft European assessment document to the manufacturer or the Group, respectively, who shall have 20 working days to react thereto. Thereafter, the organisation of TABs shall:(a)if applicable, inform the manufacturer or the Group as to how their reactions have been taken into account;(b)adopt the draft European assessment document;(c)send a copy of it to the Commission.8.2.In the case referred to in point 1.3, the responsible TAB shall:(a)adopt the draft European assessment document;(b)send a copy of it to the Commission.9.Commission assessment of draft European assessment documentsThe Commission shall assess the submitted draft European assessment document and, within 30 working days of receipt, communicate its observations to the organisation of TABs. The organisation of TABs, after having been given the opportunity to comment, shall amend the draft accordingly and resend copies of the amended draft European assessment document in accordance with point 8.1(c) and 8.2(b).10.Adoption of final European assessment document and publicationThe organisation of TABs shall adopt the final European assessment document and shall send a copy thereof to the Commission, together with a translation of its title in all the official languages of the Union, for publication of its reference in the Official Journal of the European Union without delay.The organisation of TABs shall publish the European assessment document within 90 days from the date of adoption, in one or more languages of the Union and, as a minimum, ensure that it remains accessible until all European technical assessments based on it cease to be valid.ANNEX VIIList of product families
CODEPRODUCT FAMILY
1PRECAST NORMAL/LIGHTWEIGHT/AUTOCLAVED AERATED CONCRETE PRODUCTS.
2DOORS, WINDOWS, SHUTTERS, GATES AND RELATED BUILDING HARDWARE.
3MEMBRANES, INCLUDING LIQUID APPLIED AND KITS (FOR WATER AND/OR WATER VAPOUR CONTROL).
4THERMAL INSULATION PRODUCTS. COMPOSITE INSULATING KITS/SYSTEMS.
5STRUCTURAL BEARINGS. PINS FOR STRUCTURAL JOINTS.
6CHIMNEYS, FLUES AND SPECIFIC PRODUCTS.
7GYPSUM PRODUCTS.
8GEOTEXTILES, GEOMEMBRANES, AND RELATED PRODUCTS.
9CURTAIN WALLING/CLADDING/STRUCTURAL SEALANT GLAZING.
10FIXED FIRE FIGHTING EQUIPMENT (FIRE ALARM/DETECTION, FIXED FIREFIGHTING, FIRE AND SMOKE CONTROL AND EXPLOSION SUPPRESSION PRODUCT).
11SANITARY APPLIANCES.
12CIRCULATION FIXTURES: ROAD EQUIPMENT.
13STRUCTURAL TIMBER PRODUCTS/ELEMENTS AND ANCILLARIES.
14WOOD BASED PANELS AND ELEMENTS.
15CEMENT, BUILDING LIMES AND OTHER HYDRAULIC BINDERS.
16REINFORCING AND PRESTRESSING STEEL FOR CONCRETE (AND ANCILLARIES). POST TENSIONING KITS.
17MASONRY AND RELATED PRODUCTS. MASONRY UNITS, MORTARS, AND ANCILLARIES.
18WASTE WATER ENGINEERING PRODUCTS.
19FLOORINGS.
20STRUCTURAL METALLIC PRODUCTS AND ANCILLARIES.
21INTERNAL & EXTERNAL WALL AND CEILING FINISHES. INTERNAL PARTITION KITS.
22ROOF COVERINGS, ROOF LIGHTS, ROOF WINDOWS, AND ANCILLARY PRODUCTS. ROOF KITS.
23ROAD CONSTRUCTION PRODUCTS.
24AGGREGATES.
25CONSTRUCTION ADHESIVES.
26PRODUCTS RELATED TO CONCRETE, MORTAR AND GROUT.
27SPACE HEATING APPLIANCES.
28PIPES-TANKS AND ANCILLARIES NOT IN CONTACT WITH WATER INTENDED FOR HUMAN CONSUMPTION.
29CONSTRUCTION PRODUCTS IN CONTACT WITH WATER INTENDED FOR HUMAN CONSUMPTION.
30FLAT GLASS, PROFILED GLASS AND GLASS BLOCK PRODUCTS.
31POWER, CONTROL AND COMMUNICATION CABLES.
32SEALANTS FOR JOINTS.
33FIXINGS.
34BUILDING KITS, UNITS, AND PREFABRICATED ELEMENTS.
35FIRE STOPPING, FIRE SEALING AND FIRE PROTECTIVE PRODUCTS. FIRE RETARDANT PRODUCTS.
36ATTACHED LADDERS.
ANNEX VIIIRequirements for TABsTABs shall be able to fulfil the following tasks and requirements:
CompetenceDescription of tasksRequirement
1.Analysing risksIdentify the possible risks and benefits for the use of innovative products in the absence of established/consolidated technical information regarding their performance when installed in construction works.A TAB shall be established under national law and have legal personality. It shall be independent from the stakeholders and from any particular interests.A TAB shall have staff with:(a)objectivity and sound technical judgement;(b)detailed knowledge of the regulatory provisions and other requirements in force in the Member States where it is designated, concerning product families for which it is to be designated;(c)general understanding of construction practice and detailed technical knowledge, concerning product families for which it is to be designated;(d)detailed knowledge of specific risks involved and the technical aspects of the construction process;(e)detailed knowledge of the existing harmonised standards and test methods within product families for which it is to be designated;(f)detailed knowledge of this Regulation;(g)appropriate linguistic skills.The remuneration of the TAB personnel shall not depend on the number of the assessments carried out or on the results of such assessments.
2.Setting technical criteriaTransform the outcome of the risk analysis into technical criteria for evaluating behaviour and performance of the products regarding the fulfilment of applicable national requirements;provide the technical information needed by those participating in the building process as potential users of the products (manufacturers, designers, contractors, installers).
3.Setting assessment methodsDesign and validate appropriate methods (tests or calculations) to assess performance for essential characteristics of products, taking into account the current state of the art.
4.Determining the specific factory production controlUnderstand and evaluate the manufacturing process of the specific product in order to identify appropriate measures ensuring product constancy through the given manufacturing process.A TAB shall have staff with appropriate knowledge of the relationship between the manufacturing processes and product characteristics related to factory production control.
5.Assessing the productAssess the performance for essential characteristics of products on the basis of harmonised methods against harmonised criteria.In addition to the requirements listed in points 1, 2 and 3, a TAB shall have access to the necessary means and equipment for the assessment of the performance for essential characteristics of products within product families for which it is to be designated.
6.General managementEnsure consistency, reliability, objectivity and traceability through the constant application of appropriate management methods.A TAB shall have:(a)a proven record of respect of good administrative behaviour;(b)a policy and the supporting procedures to ensure confidentiality and protection of sensitive information within the TAB and all its partners;(c)a document control system to ensure registration, traceability, maintenance, protection and archiving of all relevant documents;(d)a mechanism for internal audit and management review to ensure the regular monitoring of the compliance with appropriate management methods;(e)a procedure to manage objectively appeals and complaints.
ANNEX IXAssessment and verification systems (AVS)The manufacturer shall, in accordance with Article 22(1), correctly determine the product type and apply the corresponding product category on the basis of the applicable harmonised technical specification or European assessment document. Where a notified body is involved in assessment and verification, the notified body shall, in accordance with Article 55(1), verify that the product type was correctly determined and the corresponding product category was correctly applied.1.System 1+Full notified body control including audit sample testing(a)The manufacturer shall carry out:(i)factory production control;(ii)further testing of samples taken at the manufacturing plant in accordance with the prescribed test plan;(iii)the drawing up of technical documentation containing proof of the correct application of this Regulation with regard to the assessment of performance;(iv)the drawing up of technical documentation containing proof of conformity with the applicable product requirements under this Regulation.(b)The notified body shall decide on the issuing, restriction, suspension, or withdrawal of the certificate of constancy of performance and of conformity of the product on the basis of:(i)confirmation that the product type and the product category were correctly determined;(ii)an assessment of the performance of the product on the basis of type-testing (including sampling of the items to be taken as representative of the type), type calculation or tabulated values or documentation describing the product;(iii)initial inspection of the manufacturing plant and of factory production control;(iv)continuing surveillance, assessment and evaluation of factory production control including periodic inspections to the manufacturing plant;(v)audit-testing of samples taken before placing the product on the market;(vi)verification of the tasks under points (a) (iii) and (iv).2.System 1Full notified body control without audit sample testing(a)The manufacturer shall carry out:(i)factory production control;(ii)further testing of samples taken at the manufacturing plant by the manufacturer in accordance with the prescribed test plan;(iii)the drawing up of technical documentation containing proof of the correct application of this Regulation with regard to the assessment of performance;(iv)the drawing up of technical documentation containing proof of conformity with the applicable product requirements under this Regulation.(b)The notified body shall decide on the issuing, restriction, suspension, or withdrawal of the certificate of constancy of performance and of conformity of the product on the basis of:(i)confirmation that the product type and the product category were correctly determined;(ii)an assessment of the performance of the product on the basis of type-testing (including sampling of the item or items to be taken as representative of the type), type calculation or tabulated values or documentation describing the product;(iii)initial inspection of the manufacturing plant and of factory production control;(iv)continuing surveillance, assessment and evaluation of factory production control including periodic inspections to the manufacturing plant;(v)verification of the tasks under points (a) (iii) and (iv).3.System 2+Notified body focusing on the factory production control(a)The manufacturer shall carry out:(i)an assessment of the performance of the product on the basis of testing (including sampling of the item or items to be taken as representative of the type), type calculation, tabulated values or documentation describing that product;(ii)factory production control;(iii)testing of samples taken at the factory in accordance with the prescribed test plan;(iv)the drawing up of technical documentation containing proof of the correct application of this Regulation with regard to the assessment of performance;(v)the drawing up of technical documentation containing proof of conformity with the applicable product requirements under this Regulation.(b)The notified body shall decide on the issuing, restriction, suspension or withdrawal of the certificate of conformity of the factory production control on the basis of:(i)confirmation that the product type and the product category were correctly determined, and that the performance of the product was correctly assessed on the basis of the review of the documentation of the product;(ii)initial inspection of the manufacturing plant and of factory production control;(iii)continuing surveillance, assessment and evaluation of factory production control, including periodic inspections to the manufacturing plant;(iv)verification of the tasks under points (a) (iv) and (v).4.System 3+Notified body’s control of environmental sustainability assessment(a)The manufacturer shall carry out:(i)the assessment of the performance of the product on the basis of data collection for input values, assumptions and modelling;(ii)factory production control.(b)The notified body shall decide on the issuing, restriction, suspension or withdrawal of the validation report on the basis of:(i)validation of the input values, assumptions made and compliance with applicable generic or product category specific rules;(ii)validation of the manufacturer’s assessment;(iii)validation of the process applied to generate that assessment;(iv)validation of the correct usage of software appropriate for the assessment;(v)initial inspection of the manufacturing plant to validate any company-specific data.5.System 3Notified body focusing on the determination of the product type(a)The manufacturer shall carry out:(i)further assessment of the performance of the product on the basis of testing (including sampling of the items to be taken as representative of the type), type calculation, tabulated values or documentation describing that product;(ii)factory production control;(iii)the drawing up of technical documentation containing proof of the correct application of this Regulation with regard to the assessment of performance;(iv)the drawing up of technical documentation containing proof of conformity with the applicable product requirements under this Regulation.(b)The notified body shall decide on the issuing, restriction, suspension or withdrawal of the certificate of performance and of conformity of the product on the basis of:(i)an assessment of the performance on the basis of testing performed by a notified testing laboratory (based on sampling carried out by the manufacturer), calculation, tabulated values or documentation describing the product;(ii)confirmation that the product type and the product category were correctly determined.6.System 4Manufacturer’s self-verification and self-certification(a)The manufacturer shall carry out:(i)an assessment of the performance of the product on the basis of testing (including sampling of the items to be taken as representative of the type), type calculation, tabulated values or documentation describing that product;(ii)determine the product type and the product category on the basis of type-testing, type-calculation or tabulated values;(iii)factory production control;(iv)the drawing up of technical documentation containing proof of the correct application of this Regulation with regard to the assessment of performance;(v)the drawing up of technical documentation containing proof of conformity with the applicable product requirements under this Regulation.(b)There is no task for the notified body.7.The following horizontal rules pertaining to some or all of the systems above shall apply:(a)When a system includes an inspection of the manufacturing plant by a notified body, those inspections shall cover all locations at which significant manufacturing processes take place and shall at least include verification of the following elements:(i)the factory production control specifying the measures and frequencies foreseen to ensure constancy of performance, including the critical to performance parameters;(ii)an outline of the intended factory production control.(b)When a system includes factory production control, those controls shall cover the production process from the moment when the raw materials and components were received to the dispatch of the product ("gate to gate" approach) once that production has started, and shall at least include the following elements:(i)ensuring that the products conform to the product type and therefore attain the performance declared in the declaration of performance and conformity, and are compliant with the requirements set out in or adopted in accordance with this Regulation;(ii)application of the technical details necessary for the implementation of the assessment and verification system or systems, as defined in harmonised technical specifications, European assessment documents and voluntary harmonised standards, including, as a minimum, those parameters that are critical to performance.(c)When a system includes further testing of samples, the following shall apply:(i)tests shall include testing of an adequate number of products, as defined in harmonised technical specifications, European assessment documents and voluntary harmonised standards, with regard to conformity with the product type;(ii)where tests are not suitable for the product, the product type may be defined using the applicable extended application rules referred in harmonised technical specifications, European assessment documents and voluntary harmonised standards, where available, and notified bodies confirming that the product type was correctly determined shall also confirm that the relevant extended application rules were correctly applied;(iii)results from tests undertaken by another manufacturer or notified body may be used in accordance with Articles 59 and 62.(d)In the case of systems dealing with environmental sustainability, the validation shall consist of the validation of calculations and input data, in which context the notified body shall validate whether the modelling and input data applicable in accordance with the harmonised technical specification or European assessment document reflect the performance of the product, as well as the use of the software provided by the Commission, along with any data used, and in particular shall validate the reliability of any company-specific data used.(e)Notified bodies and manufacturers shall consider the European technical assessment issued for the product as the assessment of the performance of that product. Manufacturers finding evidence or informed by the notified body that the performance of the product is not in conformity with the European technical assessment shall bring that product into conformity with that assessment, including, when relevant, by fulfilling of obligations set out in Article 22(11).ANNEX XEssential characteristics of a horizontal natureThe following are groupings of essential characteristics of a horizontal nature, which have been developed on the basis of Annexes I and II, for the application of this Regulation.1.Reaction to fire.2.Resistance to fire.3.External fire performance.4.Noise absorption.5.Release and content of dangerous substances.6.Environmental sustainability.ANNEX XICorrelation tables
Table 1: Regulation (EU) No 305/2011 > this Regulation
Regulation (EU) No 305/2011This Regulation
Article 1Article 1
Article 2Article 3
Article 3Article 4(4)
Article 4Article 13
Article 5Article 14
Article 6Article 15
Article 7Article 16
Article 8Article 17
Article 9Article 18
Article 10Article 72
Article 11Articles 20 and 22
Article 12Articles 20 and 23
Article 13Articles 20 and 24
Article 14Articles 20 and 25
Article 15Articles 20 and 26
Article 16Article 20
Article 17Article 5
Article 18Article 5
Article 19Article 31
Article 20Article 32
Article 21Article 33
Article 22Article 34
Article 23—
Article 24Article 35
Article 25Article 36
Article 26Article 37
Article 27Article 5(5) and (6)
Article 28Article 10
Article 29Article 39
Article 30Article 40
Article 31Article 41
Article 32Article 41
Article 33Article 41
Article 34Article 41
Article 35—
Article 36Article 59
Article 37Article 60
Article 38Article 61
Article 38aArticle 85
Article 38bArticle 86
Article 38cArticle 87
Article 38dArticle 88
Article 39Article 42
Article 40Article 43
Article 41Article 44
Article 42—
Article 43Article 46
Article 44Article 47
Article 45Article 48
Article 46Article 49
Article 47Article 50
Article 48Article 51
Article 49Article 52
Article 50Article 53
Article 51Article 54
Article 52Article 55
Article 53Article 56
Article 54Article 45
Article 55Article 58
Article 56Article 65
Article 57Article 66
Article 58Article 67
Article 59Article 65
Article 60Article 89
Article 61Article 89
Article 62Article 89
Article 63Article 89
Article 64Article 90
Article 65Article 94
Article 66Article 95
Article 67Article 93
Article 68Article 96
Table 2: this Regulation > Regulation (EU) No 305/2011
This RegulationRegulation (EU) No 305/2011
Article 1Article 1
Article 2—
Article 3Article 2
Article 4Article 3
Article 5Articles 17, 18 and 27
Article 6—
Article 7—
Article 8—
Article 9—
Article 10Article 28
Article 11—
Article 12—
Article 13Article 4
Article 14Article 5
Article 15Article 6
Article 16Article 7
Article 17Article 8
Article 18Article 9
Article 19—
Article 20Articles 11, 12, 13, 14, 15 and 16
Article 21—
Article 22Article 11
Article 23Article 12
Article 24Article 13
Article 25Article 14
Article 26Article 15
Article 27—
Article 28—
Article 29—
Article 30—
Article 31Article 19
Article 32Article 20
Article 33Article 21
Article 34Article 22
Article 35Article 24
Article 36Article 25
Article 37Article 26
Article 38—
Article 39Article 29
Article 40Article 30
Article 41Articles 31-34
Article 42Article 39
Article 43Article 40
Article 44Article 41
Article 45Article 54
Article 46Article 43
Article 47Article 44
Article 48Article 45
Article 49Article 46
Article 50Article 47
Article 51Article 48
Article 52Article 49
Article 53Article 50
Article 54Article 51
Article 55Article 52
Article 56Article 53
Article 57—
Article 58Article 55
Article 59Article 36
Article 60Article 37
Article 61Article 38
Article 62—
Article 63—
Article 64—
Article 65Articles 56 and 59
Article 66Article 57
Article 67Article 58
Article 68—
Article 69—
Article 70—
Article 71—
Article 72Article 10
Article 73—
Article 74—
Article 75—
Article 76—
Article 77—
Article 78—
Article 79—
Article 80—
Article 81—
Article 82—
Article 83—
Article 84—
Article 85Article 38a
Article 86Article 38b
Article 87Article 38c
Article 88Article 38d
Article 89Articles 60-63
Article 90Article 64
Article 91—
Article 92—
Article 93Article 67
Article 94Article 65
Article 95Article 66
Article 96Article 68