Directive (EU) 2024/1275 of the European Parliament and of the Council of 24 April 2024 on the energy performance of buildings (recast) (Text with EEA relevance)
Directive (EU) 2024/1275 of the European Parliament and of the Councilof 24 April 2024on the energy performance of buildings(recast)(Text with EEA relevance) THE EUROPEAN PARLIAMENT AND THE COUNCIL OF THE EUROPEAN UNION,Having regard to the Treaty on the Functioning of the European Union, and in particular Article 194(2) thereof,Having regard to the proposal from the European Commission,After transmission of the draft legislative act to the national parliaments,Having regard to the opinion of the European Economic and Social CommitteeOJ C 290, 29.7.2022, p. 114.,Having regard to the opinion of the Committee of the RegionsOJ C 375, 30.9.2022, p. 64.,Acting in accordance with the ordinary legislative procedurePosition of the European Parliament of 12 March 2024 (not yet published in the Official Journal) and decision of the Council of 12 April 2024.,Whereas:(1)Directive 2010/31/EU of the European Parliament and of the CouncilDirective 2010/31/EU of the European Parliament and of the Council of 19 May 2010 on the energy performance of buildings (OJ L 153, 18.6.2010, p. 13). has been substantially amended several timesSee Annex IX, Part A.. Since further amendments are to be made, that Directive should be recast in the interests of clarity.(2)Under the Paris AgreementOJ L 282, 19.10.2016, p. 4., adopted in December 2015 under the United Nations Framework Convention on Climate Change (UNFCCC) (the "Paris Agreement"), its Parties have agreed to hold the increase in the global average temperature well below 2 oC above pre-industrial levels and to pursue efforts to limit the temperature increase to 1,5 oC above pre-industrial levels. Reaching the objectives of the Paris Agreement is at the core of the Commission communication of 11 December 2019 entitled "The European Green Deal" (the "European Green Deal"). The Union committed itself to reducing the Union’s economy-wide net greenhouse gas emissions by at least 55 % by 2030 below 1990 levels in the updated nationally determined contribution submitted to the UNFCCC Secretariat on 17 December 2020.(3)As announced in the European Green Deal, the Commission presented its Renovation Wave strategy in its communication of 14 October 2020 entitled "A Renovation Wave for Europe — greening our buildings, creating jobs, improving lives". The Renovation Wave strategy contains an action plan with concrete regulatory, financing and enabling measures, with the objective to at least double the annual energy renovation rate of buildings by 2030 and to foster deep renovations, resulting in 35 million building units renovated by 2030 and the creation of jobs in the construction sector. The revision of Directive 2010/31/EU is necessary as one of the vehicles by which to deliver on the Renovation Wave. It will also contribute to delivering on the New European Bauhaus initiative, presented in the Commission communication of 15 September 2021 entitled "New European Bauhaus — Beautiful, Sustainable, Together" and the European mission on climate-neutral and smart cities. The New European Bauhaus initiative is intended to foster a more inclusive society that promotes the wellbeing of all in keeping with the historical Bauhaus, which contributed to social inclusion and the well-being of citizens, in particular worker communities. By facilitating training, networks and providing guidelines to architects, students, engineers and designers under the principles of sustainability, aesthetics and inclusion, the New European Bauhaus initiative can empower local authorities to develop innovative and cultural solutions in creating a more sustainable built environment.(4)Regulation (EU) 2021/1119 of the European Parliament and of the CouncilRegulation (EU) 2021/1119 of the European Parliament and of the Council of 30 June 2021 establishing the framework for achieving climate neutrality and amending Regulations (EC) No 401/2009 and (EU) 2018/1999 ("European Climate Law") (OJ L 243, 9.7.2021, p. 1). enshrines in Union law the target of economy-wide climate neutrality by 2050 at the latest and establishes a binding Union domestic reduction commitment of net greenhouse gas emissions (emissions after the deduction of removals) of at least 55 % below 1990 levels by 2030.(5)The "Fit for 55" legislative package, announced by means of the Commission communication of 19 October 2020 entitled "Commission Work Programme 2021 — A Union of vitality in a world of fragility", aims to implement those objectives. That package covers a range of policy areas including energy efficiency, renewable energy, land use, land change and forestry, energy taxation, effort sharing, emissions trading and alternative fuels infrastructure. The revision of Directive 2010/31/EU is an integral part of that package. Building on the "Fit for 55" legislative package, the REPowerEU plan contained in the Commission communication of 18 May 2022 entitled "REPowerEU Plan" put forward an additional set of actions to save energy, diversify supplies, quickly substitute fossil fuels by accelerating Europe’s clean energy transition and smartly combine investments and reforms. It contained new legislative proposals and targeted recommendations by which to increase ambition with regard to energy efficiency and savings. The communication also referred to taxation measures as means to provide incentives for energy savings and reduce fossil fuel consumption.(6)Buildings account for 40 % of final energy consumption in the Union and 36 % of its energy-related greenhouse gas emissions while 75 % of Union buildings are still energy-inefficient. Natural gas plays the largest role in the heating of buildings, accounting for around 39 % of energy consumption used for space heating in the residential sector. Oil is the second most important fossil fuel for heating, accounting for 11 % and coal accounts for around 3 %. Therefore, reduction of energy consumption, in line with the "energy efficiency first" principle as laid down in Article 3 of Directive (EU) 2023/1791 of the European Parliament and of the CouncilDirective (EU) 2023/1791 of the European Parliament and of the Council of 13 September 2023 on energy efficiency and amending Regulation (EU) 2023/955 (OJ L 231, 20.9.2023, p. 1). and defined in Article 2, point (18), of Regulation (EU) 2018/1999 of the European Parliament and of the CouncilRegulation (EU) 2018/1999 of the European Parliament and of the Council of 11 December 2018 on the Governance of the Energy Union and Climate Action, amending Regulations (EC) No 663/2009 and (EC) No 715/2009 of the European Parliament and of the Council, Directives 94/22/EC, 98/70/EC, 2009/31/EC, 2009/73/EC, 2010/31/EU, 2012/27/EU and 2013/30/EU of the European Parliament and of the Council, Council Directives 2009/119/EC and (EU) 2015/652 and repealing Regulation (EU) No 525/2013 of the European Parliament and of the Council (OJ L 328, 21.12.2018, p. 1). and the use of energy from renewable sources in the buildings sector constitute important measures needed to reduce greenhouse gas emissions and energy poverty in the Union. Reduced energy consumption and an increased use of energy from renewable sources, especially solar energy, also have a key role to play in reducing the Union’s energy dependency on fossil fuels overall and on imports especially, promoting security of energy supply in line with the objectives set out in the REPowerEU plan, fostering technological developments and in creating opportunities for employment and regional development, in particular in islands, rural areas and off-grid communities.(7)Buildings are responsible for greenhouse gas emissions before, during and after their operational lifetime. The 2050 vision for a decarbonised building stock goes beyond the current focus on operational greenhouse gas emissions. The whole-life-cycle emissions of buildings should therefore progressively be taken into account, starting with new buildings. Buildings are a significant material bank, being repositories for resources over many decades, and the design options and choices of materials largely influence the whole-life-cycle emissions both for new buildings and renovations. The whole-life-cycle performance of buildings should be taken into account not only in new construction, but also in renovations through the inclusion of policies for the reduction of whole-life-cycle greenhouse gas emissions in Member States’ national building renovation plans.(8)Minimising the whole-life-cycle greenhouse gas emissions of buildings requires resource efficiency and circularity. This can also be combined with turning parts of the building stock into a temporary carbon sink.(9)The global warming potential (GWP) over a building’s whole life cycle indicates the building’s overall contribution to emissions that lead to climate change. It brings together greenhouse gas emissions embodied in construction products with direct and indirect emissions from the use stage. A requirement to calculate the life-cycle GWP of new buildings therefore constitutes a first step towards increased consideration of the whole-life-cycle performance of buildings and a circular economy.(10)Buildings are responsible for about half of primary fine particulate matter (PM2,5) emissions in the Union that cause premature death and illness. Improving the energy performance of buildings can and should reduce pollutant emissions at the same time, in accordance with Directive (EU) 2016/2284 of the European Parliament and of the CouncilDirective (EU) 2016/2284 of the European Parliament and of the Council of 14 December 2016 on the reduction of national emissions of certain atmospheric pollutants, amending Directive 2003/35/EC and repealing Directive 2001/81/EC (OJ L 344, 17.12.2016, p. 1)..(11)Measures to improve further the energy performance of buildings should take into account climatic conditions, including adaptation to climate change, local conditions as well as the indoor climate and cost-effectiveness. Those measures should not affect other requirements concerning buildings such as accessibility, fire safety and seismic safety and the intended use of the building.(12)The energy performance of buildings should be calculated on the basis of a methodology, which may be differentiated at national and regional level. That methodology should include, in addition to thermal characteristics, other factors that play an increasingly important role such as urban heat island effect, heating and air-conditioning installations, the use of energy from renewable sources, building automation and control systems, heat recovery from exhaust air or waste water, system balancing, smart solutions, passive heating and cooling elements, shading, indoor environmental quality, adequate natural light and design of the building. The methodology for calculating the energy performance of buildings should be based not only on the season in which heating or air-conditioning is required, but should cover the annual energy performance of a building. It should take into account existing European standards. The methodology should ensure the representation of actual operating conditions and enable the use of metered energy to verify correctness and for comparability, and should be based on monthly, hourly or sub-hourly calculation intervals. In order to encourage the use of on-site renewable energy, and in addition to the common general framework, Member States should take the necessary measures to the effect that the benefits of maximising the use of on-site renewable energy, including for other uses, such as electric vehicle recharging points, are recognised and accounted for in the calculation methodology.(13)Member States should set minimum energy performance requirements for buildings and building elements with a view to achieving the cost-optimal balance between the investments involved and the energy costs saved throughout the life cycle of the building, without prejudice to the right of Member States to set minimum energy performance requirements which are more energy-efficient than cost-optimal energy efficiency levels. Provision should be made for the possibility for Member States to review regularly their minimum energy performance requirements for buildings in light of technical progress.(14)Two thirds of the energy used for heating and cooling of buildings still comes from fossil fuels. In order to decarbonise the building sector, it is of particular importance to phase out fossil fuel in heating and cooling. Therefore, Member States should indicate their national policies and measures to phase out fossil fuels in heating and cooling in their national building renovation plans. They should strive to phase out stand-alone boilers powered by fossil fuels, and, as a first step, they should not provide, from 2025, financial incentives for the installation of stand-alone boilers powered by fossil fuels, with the exception of those selected for investment, before 2025, under the Recovery and Resilience Facility established by Regulation (EU) 2021/241 of the European Parliament and of the CouncilRegulation (EU) 2021/241 of the European Parliament and of the Council of 12 February 2021 establishing the Recovery and Resilience Facility (OJ L 57, 18.2.2021, p. 17)., and the European Regional Development Fund and the Cohesion Fund under Regulation (EU) 2021/1058 of the European Parliament and of the CouncilRegulation (EU) 2021/1058 of the European Parliament and of the Council of 24 June 2021 on the European Regional Development Fund and on the Cohesion Fund (OJ L 231, 30.6.2021, p. 60).. It should still be possible to provide financial incentives for the installation of hybrid heating systems with a considerable share of renewable energy, such as the combination of a boiler with solar thermal or with a heat pump. A clear legal basis for the banning of heat generators on the basis of their greenhouse gas emissions, the type of fuel used or to the minimum part of renewable energy used for heating at building’s level should support national phase-out policies and measures.(15)Domestic hot-water generation is one of the main sources of energy consumption for high-performing buildings. In most cases, that energy is not recovered. Harvesting heat from domestic hot-water drains in buildings could be a simple and cost-effective way to save energy.(16)Energy performance requirements for technical building systems should apply to whole systems, as installed in buildings, and not to the performance of standalone components, which fall under the scope of product-specific regulations under Directive 2009/125/EC of the European Parliament and of the CouncilDirective 2009/125/EC of the European Parliament and of the Council of 21 October 2009 establishing a framework for the setting of ecodesign requirements for energy-related products (OJ L 285, 31.10.2009, p. 10).. When setting energy performance requirements for technical building systems, Member States should use, where available and appropriate, harmonised instruments, in particular testing and calculation methods and energy efficiency classes developed under measures implementing Directive 2009/125/EC and Regulation (EU) 2017/1369 of the European Parliament and of the CouncilRegulation (EU) 2017/1369 of the European Parliament and of the Council of 4 July 2017 setting a framework for energy labelling and repealing Directive 2010/30/EU (OJ L 198, 28.7.2017, p. 1)., with a view to ensuring consistency with related initiatives and minimise, to the extent possible, potential fragmentation of the market. Energy-saving technologies with very short payback periods, such as the installation or replacement of thermostatic control valves or heat recovery from exhaust air or waste water, are given insufficient consideration today. When estimating the effective rated output for heating systems, air-conditioning systems, systems for combined space heating and ventilation, or systems for combined air-conditioning and ventilation systems, in a given building or building unit the effective rated output of different generators of the same system should be added together.(17)This Directive is without prejudice to Articles 107 and 108 of the Treaty on the Functioning of the European Union (TFEU). The term "incentive" as used in this Directive should not therefore be interpreted as constituting State aid.(18)The Commission should lay down a comparative methodology framework for calculating cost-optimal levels of minimum energy performance requirements. A review of that framework should enable the calculation of both energy and emission performance and should take into account environmental and health externalities, as well as the extension of the emission trading system and carbon prices. Member States should use that framework to compare the results with the minimum energy performance requirements which they have adopted. Should there be significant discrepancies, namely discrepancies that exceed 15 %, between the calculated cost-optimal levels of minimum energy performance requirements and the minimum energy performance requirements in force, Member States should justify the difference or plan appropriate steps to reduce the discrepancy. The estimated economic life cycle of a building or building element should be determined by Member States, taking into account current practices and experience in defining typical economic life cycles. Member States should submit to the Commission, on a regular basis, the results of that comparison and the data used to reach those results. Those reports should enable the Commission to assess and report on the progress of Member States in reaching cost-optimal levels of minimum energy performance requirements.(19)Major renovations of existing buildings, regardless of their size, provide an opportunity to take cost-effective measures to enhance energy performance. For reasons of cost-effectiveness, it should be possible to limit the minimum energy performance requirements to the renovated parts that are most relevant for the energy performance of the building. Member States should be able to define a "major renovation" either in terms of a percentage of the surface of the building envelope or in terms of the value of the building. If a Member State decides to define a major renovation in terms of the value of the building, values such as the actuarial value, or the current value based on the cost of reconstruction, excluding the value of the land upon which the building is situated, could be used.(20)The enhanced climate and energy ambition of the Union requires a new vision for buildings: the zero-emission building, with very low energy demand, zero on-site carbon emissions from fossil fuels and zero or a very low amount of operational greenhouse gas emissions. All new buildings should be zero-emission buildings by 2030, and existing buildings should be transformed into zero-emission buildings by 2050.(21)Where an existing building is altered, it is not considered to be a new building.(22)Different options are available to cover the energy needs of a zero-emission building: energy generated on site or nearby from renewable sources such as solar thermal, geothermal, solar photovoltaics, heat pumps, hydroelectric power and biomass, renewable energy provided by renewable energy communities, efficient district heating and cooling, and energy from other carbon-free sources. Energy derived from combustion of renewable fuels is considered to be energy from renewable sources generated on-site where the combustion of the renewable fuel takes place on-site.(23)Zero-emission buildings can contribute to demand-side flexibility for instance through demand management, electrical storage, thermal storage and distributed renewable generation to support a more reliable, sustainable and efficient energy system.(24)The necessary decarbonisation of the Union building stock requires energy renovation at a large scale: almost 75 % of that building stock is inefficient according to current building standards, and 85 to 95 % of the buildings that exist today will still be standing in 2050. However, the weighted annual energy renovation rate is persistently low at around 1 %. At the current pace, the decarbonisation of the building sector would require centuries. Triggering and supporting building renovation, including a shift towards emission-free heating systems, is therefore a key goal of this Directive. Supporting renovations at district-level, including through industrial or serial type renovations, offers benefits by stimulating the volume and depth of building renovations and will lead to a quicker and cheaper decarbonisation of the building stock. Industrial solutions for construction and building renovation include versatile prefabricated elements providing different functions such as insulation and energy generation.(25)Minimum energy performance standards are the essential regulatory tool by means of which to trigger the renovation of existing buildings on a large scale, as they tackle the key barriers to renovation such as split incentives and co-ownership structures, which cannot be overcome by economic incentives. The introduction of minimum energy performance standards should lead to a gradual phasing out of the worst-performing buildings and a continuous improvement of the national building stock, contributing to the long-term goal of a decarbonised building stock by 2050.(26)Minimum energy performance standards for non-residential buildings should be provided for at Union level and should focus on the renovation of the worst-performing non-residential buildings, which have the highest potential in terms of decarbonisation and extended social and economic benefits and therefore need to be renovated as a priority. In addition, Member States should establish specific timelines for the further renovation of non-residential buildings in their national building renovation plans. Some specific situations justify exemptions for individual non-residential buildings from minimum energy performance standards, in particular the planned demolition of a building or an unfavourable cost-benefit assessment; cases of serious hardship justify an exemption for as long as the hardship persists. Member States should establish stringent criteria for such exemptions in order to avoid a disproportionate share of exempted non-residential buildings. They should communicate those criteria in their national building renovation plans and should compensate for the exempted non-residential buildings via equivalent energy performance improvements in other parts of the non-residential building stock.(27)As regards residential buildings, Member States should have the flexibility to choose the tools by means of which they achieve the required improvement of the residential building stock, such as minimum energy performance standards, technical assistance and financial support measures. Member States should establish a national trajectory for the progressive renovation of the national residential building stock in line with the national roadmap and the 2030, 2040 and 2050 targets contained in the Member State’s national building renovation plan and with the transformation of the national building stock into a zero-emission building stock by 2050. The national trajectories should comply with intermediate, five-year milestones for the decrease in the average primary energy use of the residential building stock, starting in 2030, which ensure similar efforts across Member States.(28)As regards the rest of the national building stock, Member States are free to decide whether they wish to introduce minimum energy performance standards, designed at national level and adapted to national conditions. When reviewing this Directive, the Commission should assess whether the measures established pursuant to this Directive will deliver sufficient progress towards achieving a fully decarbonised, zero-emission building stock by 2050 or whether further measures, such as binding minimum energy performance standards need to be introduced, in particular for residential buildings in order to achieve the five-year milestones.(29)The introduction of minimum energy performance standards should be accompanied by an enabling framework including technical assistance and financial measures, in particular for vulnerable households. Minimum energy performance standards set at national level do not amount to "Union standards" within the meaning of State aid rules, while Union-wide minimum energy performance standards might be considered to constitute such "Union standards". In line with revised State aid rules, Member States may grant State aid to building renovation to comply with the Union-wide energy performance standards until those Union-wide standards become mandatory. Once the standards are mandatory, Member States may continue to grant State aid for the renovation of buildings and building units falling under the Union-wide energy performance standards, provided that the building renovation aims at a higher standard.(30)The EU Taxonomy, established by Regulation (EU) 2020/852 of the European Parliament and of the CouncilRegulation (EU) 2020/852 of the European Parliament and of the Council of 18 June 2020 on the establishment of a framework to facilitate sustainable investment, and amending Regulation (EU) 2019/2088 (OJ L 198, 22.6.2020, p. 13)., classifies environmentally sustainable economic activities across the economy, including for the building sector. Under Commission Delegated Regulation (EU) 2021/2139Commission Delegated Regulation (EU) 2021/2139 of 4 June 2021 supplementing Regulation (EU) 2020/852 of the European Parliament and of the Council by establishing the technical screening criteria for determining the conditions under which an economic activity qualifies as contributing substantially to climate change mitigation or climate change adaptation and for determining whether that economic activity causes no significant harm to any of the other environmental objectives (OJ L 442, 9.12.2021, p. 1). (the "EU Taxonomy Climate Delegated Act"), building renovation is considered to be a sustainable activity where it achieves at least 30 % energy savings, complies with minimum energy performance requirements for major renovation of existing buildings, or consists of individual measures related to the energy performance of buildings, such as the installation, maintenance or repair of energy efficiency equipment or of instruments and devices for measuring, regulating and controlling the energy performance of buildings, where such individual measures comply with the established criteria. Building renovation to comply with Union-wide minimum energy performance standards is typically in line with the EU Taxonomy criteria related to building renovation activities.(31)Minimum energy performance requirements for existing buildings and building elements were already contained in the predecessors of this Directive and should continue to apply. While the newly introduced minimum energy performance standards set a minimum level for the energy performance of existing buildings and ensure that renovation of inefficient buildings takes place, minimum energy performance requirements for existing buildings and building elements ensure the necessary depth of renovation when a renovation takes place.(32)There is an urgent need to reduce the dependence on fossil fuels in buildings and to accelerate efforts to decarbonise and electrify their energy consumption. In order to enable the cost-effective installation of solar technologies at a later stage, all new buildings should be "solar-ready", that is, designed to optimise the solar generation potential on the basis of the site’s solar irradiance, enabling the installation of solar technologies without costly structural interventions. In addition, Member States should ensure the deployment of suitable solar installations on new buildings, both residential and non-residential, and on existing non-residential buildings. The large-scale deployment of solar energy on buildings would make a major contribution to shielding more effectively consumers from increasing and volatile prices of fossil fuels, reduce the exposure of vulnerable citizens to high energy costs and result in wider environmental, economic and social benefits. In order to efficiently exploit the potential of solar installations on buildings, Member States should establish criteria for the implementation of, and possible exemptions from, the deployment of solar installations on buildings, in line with the assessed technical and economic potential of the solar energy installations and the characteristics of the buildings covered by this obligation, taking into account the principle of technology neutrality and the combination of solar installations with other roof uses, such as green roofs or other building services installations. In their criteria for the practical implementation of the obligations of deployment of suitable solar energy installation on buildings, Member States should be able to express the relevant threshold in terms of the building’s ground floor area instead of the building’s useful floor area, provided that such a method corresponds to an equivalent installed capacity of suitable solar energy installation on buildings. As the obligation to deploy solar installations on individual buildings depends on the criteria established by Member States, the provisions on solar energy on buildings do not qualify as a "Union standard" within the meaning of State aid rules.(33)It should be possible for Member States to encourage, by means of information, appropriate administrative procedures or other measures that are set out in their national building renovation plans, the deployment of suitable solar energy installations in combination with the renovation of the building envelope, with the replacement of technical building systems or with the installation of recharging infrastructure for electric vehicles, of heat pumps or of building automation and control systems.(34)With regard to mixed-used buildings that include both residential and non-residential building units, Member States may continue to choose whether to treat them as residential or non-residential buildings.(35)Solar photovoltaics and solar thermal technologies, including in combination with energy storage, should be rolled out rapidly to benefit both the climate and the finances of citizens and businesses.(36)The electrification of buildings, such as through the deployment of heat pumps, solar installations, batteries and recharging infrastructure, changes the risks with regard to the fire safety of buildings, which Member States need to address. As regards fire safety in car parks, the Commission should publish non-binding guidance for Member States.(37)To achieve a highly energy-efficient and decarbonised building stock and the transformation of existing buildings into zero-emission buildings by 2050, Member States should establish national building renovation plans which replace the long-term renovation strategies provided for in Article 2a of Directive 2010/31/EU and which are to become an even stronger, fully operational planning tool for Member States, in line with the "energy efficiency first" principle, with a stronger focus on financing and ensuring that appropriately skilled workers are available for carrying out building renovations Member States may take into account the Pact for Skills set out in the communication of the Commission of 1 July 2020 entitled "European Skills Agenda for sustainable competitiveness, social fairness and resilience". In their national building renovation plans, Member States should set their own national building renovation targets. In accordance with Article 21, point (b)(7), of Regulation (EU) 2018/1999 and with the enabling conditions set under Regulation (EU) 2021/1060 of the European Parliament and of the CouncilRegulation (EU) 2021/1060 of the European Parliament and of the Council of 24 June 2021 laying down common provisions on the European Regional Development Fund, the European Social Fund Plus, the Cohesion Fund, the Just Transition Fund and the European Maritime, Fisheries and Aquaculture Fund and financial rules for those and for the Asylum, Migration and Integration Fund, the Internal Security Fund and the Instrument for Financial Support for Border Management and Visa Policy (OJ L 231, 30.6.2021, p. 159)., Member States should provide an outline of financing measures, as well as an outline of the investment needs and the administrative resources for the implementation of their national building renovation plans.(38)The "energy efficiency first" principle is an overarching principle that should be taken into account across all sectors, going beyond the energy system, at all levels. It is defined in Article 2, point (18), of Regulation (EU) 2018/1999 as meaning to take utmost account in energy planning, and in policy and investment decisions, of alternative cost-efficient energy efficiency measures to make energy demand and energy supply more efficient, in particular by means of cost-effective end-use energy savings, demand-response initiatives and more efficient conversion, transmission and distribution of energy, whilst still achieving the objectives of those decisions. The principle is therefore equally relevant with regard to improving the energy performance of buildings and is highlighted in the Renovation Wave strategy as one of the key principles for building renovation towards 2030 and 2050. As set out in Commission Recommendation (EU) 2021/1749Commission Recommendation (EU) 2021/1749 of 28 September 2021 on Energy Efficiency First: from principles to practice — Guidelines and examples for its implementation in decision-making in the energy sector and beyond (OJ L 350, 4.10.2021, p. 9)., improved health and well-being are among the major co-benefits of applying the "energy efficiency first" principle to improve the energy performance of buildings.(39)In order to ensure that the Union’s workforce is fully prepared to work actively towards the achievement of the Union climate objectives, Member States should encourage under-represented groups to train and work in the construction and building sector.(40)The national building renovation plans should be based on a harmonised template in order to ensure comparability of plans. In order to ensure the required ambition, the Commission should assess the draft national building renovation plans and issue recommendations to Member States.(41)The national building renovation plans should be closely linked with the integrated national energy and climate plans under Regulation (EU) 2018/1999, and progress in achieving the national targets and the contribution of the national building renovation plans to national and Union targets should be reported as part of the biennial reporting under Regulation (EU) 2018/1999. Considering the urgency to scale up renovation on the basis of solid national building renovation plans, the date for the submission of the first national building renovation plan should be set as early as possible. The subsequent national building renovation plans should be submitted as part of the integrated national energy and climate plans and their updates, which means that the second draft national building renovation plan should be submitted with the second draft integrated national energy and climate plans in 2028.(42)A staged deep renovation can be a solution to address high upfront costs and hassle for the inhabitants that may occur when renovating "in one go" and can allow for less disruptive and more financially feasible renovation measures. However, such staged deep renovation needs to be carefully planned in order to avoid that one renovation step precludes necessary subsequent steps. One-step deep renovation can be more cost-effective and result in fewer emissions linked to the renovation than staged renovation. Renovation passports provide a clear roadmap for staged deep renovations, helping owners and investors plan the best timing and scope for interventions. Therefore, renovation passports should be encouraged and made available, as a voluntary tool, to building owners across all Member States. Member States should ensure that renovation passports do not create a disproportionate burden.(43)There are some synergies between renovation passports and energy performance certificates, in particular as regards the assessment of the current performance of the building and the recommendations for its improvement. In order to make the most of those synergies and reduce costs for building owners, Member States should be able to allow the renovation passport and the energy performance certificate to be drawn up jointly by the same expert and issued together. In the case of such joint drawing up and issuing, the renovation passport should substitute the recommendations in the energy performance certificate. It should, however, remain possible to obtain an energy performance certificate without a renovation passport.(44)Long-term renovation contracts are an important instrument by means of which to stimulate staged renovation. Member States may introduce mechanisms that allow the establishment of long-term renovation contracts over the various stages of staged renovation. Where new and more effective incentives become available during the various stages of the renovation, access to those new incentives may be ensured by allowing beneficiaries to switch to new incentives.(45)The concept of "deep renovation" has not yet been defined in Union law. With a view to achieving the long-term vision for buildings, deep renovation should be defined as a renovation that transforms buildings into zero-emission buildings but, as a first step, as a renovation that transforms buildings into nearly zero-energy buildings. This definition serves the purpose of increasing the energy performance of buildings. A deep renovation for energy performance purposes may also be a prime opportunity to address other aspects such as indoor environmental quality, living conditions of vulnerable households, increasing climate resilience, resilience against disaster risks including seismic resilience, fire safety, the removal of hazardous substances including asbestos, and accessibility for persons with disabilities.(46)In order to foster deep renovation, which is one of the goals of the Renovation Wave strategy, Member States should give enhanced financial and administrative support to deep renovation.(47)Member States should support energy performance upgrades of existing buildings that contribute to achieving an adequate level of indoor environmental quality, removing asbestos and other harmful substances, preventing the illegal removal of harmful substances, and facilitating compliance with existing legislative acts such as Directives 2009/148/ECDirective 2009/148/EC of the European Parliament and of the Council of 30 November 2009 on the protection of workers from the risks related to exposure to asbestos at work (OJ L 330, 16.12.2009, p. 28). and (EU) 2016/2284Directive (EU) 2016/2284 of the European Parliament and of the Council of 14 December 2016 on the reduction of national emissions of certain atmospheric pollutants, amending Directive 2003/35/EC and repealing Directive 2001/81/EC (OJ L 344, 17.12.2016, p. 1). of the European Parliament and of the Council.(48)Integrated district or neighbourhood approaches help to increase the cost-effectiveness of the renovations required for buildings that are spatially related such as housing blocks. Such approaches to renovations offer a variety of solutions at a larger scale.(49)Electric vehicles are expected to play a crucial role in the decarbonisation and efficiency of the electricity system, namely through the provision of flexibility, balancing and storage services, especially through aggregation. This potential of electric vehicles to integrate with the electricity system and contribute to system efficiency and further absorption of renewable electricity should be fully exploited. Recharging in relation to buildings is particularly important, since this is where electric vehicles park regularly and for long periods of time. Slow recharging is economical and the installation of recharging points in private spaces can provide energy storage to the related building and integration of smart recharging services and bi-directional recharging and system integration services in general.(50)Combined with an increased share of renewable electricity production, electric vehicles produce less greenhouse gas emissions. Electric vehicles constitute an important component of a clean energy transition on the basis of energy efficiency measures, alternative fuels, renewable energy and innovative solutions for the management of energy flexibility. Building codes can be effectively used to introduce targeted requirements to support the deployment of recharging infrastructure in car parks of residential and non-residential buildings. Member States should aim to remove barriers such as split incentives and administrative complications which individual owners encounter when trying to install a recharging point on their parking space.(51)Pre-cabling and ducting facilitate the rapid deployment of recharging points if and where they are needed. Readily available infrastructure will decrease the costs of installation of recharging points for individual owners and ensure that electric vehicle users have access to recharging points. Establishing requirements for electromobility at Union level concerning the pre-equipping of parking spaces and the installation of recharging points is an effective way to promote electric vehicles in the near future while enabling further development at a reduced cost in the medium to long term. Where technically feasible, Member States should ensure the accessibility of recharging points for persons with disabilities.(52)Smart recharging and bi-directional recharging enable the energy system integration of buildings. Recharging points where electric vehicles typically park for extended periods of time, such as where people park for reasons of residence or employment, are highly relevant to energy system integration, therefore smart recharging functionalities need to be ensured. In situations where bi-directional recharging would assist further penetration of renewable electricity by electric vehicle fleets in transport and the electricity system in general, such functionality should also be made available.(53)Promoting green mobility is a key part of the European Green Deal and buildings can play an important role in providing the necessary infrastructure, not only for recharging of electric vehicles but also for bicycles. A shift to active mobility such as cycling can significantly reduce greenhouse gas emissions from transport. With the increase in the sale of electrically power-assisted cycles and other L-category vehicle types, referred to in Article 4 of Regulation (EU) No 168/2013 of the European Parliament and of the CouncilRegulation (EU) No 168/2013 of the European Parliament and of the Council of 15 January 2013 on the approval and market surveillance of two- or three-wheel vehicles and quadricycles (OJ L 60, 2.3.2013, p. 52)., and in order to facilitate the installation of recharging points at a later stage, pre-cabling or ducting should be required in new residential buildings and, where technically and economically feasible, in residential buildings undergoing major renovation. As set out in the communication of the Commission of 17 September 2020 on "Stepping up Europe’s 2030 climate ambition — Investing in a climate-neutral future for the benefit of our people" (the "Climate Target Plan"), increasing the modal shares of clean and efficient private and public transport, such as cycling, will drastically lower pollution from transport and bring major benefits to individual citizens and communities. The lack of bicycle parking spaces is a major barrier to the uptake of cycling, both in residential and non-residential buildings. Union requirements and national building codes can effectively support the transition to cleaner mobility by establishing requirements for a minimum number of bicycle parking spaces, and building bicycle parking spaces and related infrastructure in areas where bicycles are less used can lead to an increase in their use. The requirement to provide bicycle parking spaces should not depend on, or necessarily be linked to, the availability and supply of car parking spaces, which may be unavailable in certain circumstances. Member States should allow an increase in bicycle parking in residential buildings where there are no car parking spaces by providing for the installation of at least two bicycle parking spaces for every residential building unit.(54)The agendas of the Digital Single Market and the Energy Union should be aligned and should serve common goals. The digitalisation of the energy system is quickly changing the energy landscape, from the integration of renewables to smart grids and smart-ready buildings. In order to digitalise the building sector, the Union’s connectivity targets and ambitions for the deployment of high-capacity communication networks are important for smart homes and well-connected communities. Targeted incentives should be provided to promote smart-ready systems and digital solutions in the built environment. This would offer new opportunities for energy savings, by providing consumers with more accurate information about their consumption patterns, and by enabling the system operator to manage the grid more effectively. Member States should encourage the use of digital technologies for analysis, simulation and management of buildings, including with regard to deep renovations.(55)In order to facilitate a competitive and innovative market for smart building services that contributes to efficient energy use and integration of renewable energy in buildings and support investments in renovation, Member States should ensure direct access to building systems’ data by interested parties. To avoid excessive administrative costs for third parties, Member States shall facilitate the full interoperability of services and of the data exchange within the Union.(56)The smart readiness indicator should be used to measure the capacity of buildings to use information and communication technologies and electronic systems to adapt the operation of buildings to the needs of the occupants and the grid and to improve the energy efficiency and overall performance of buildings. The smart readiness indicator should raise awareness among building owners and occupants of the value behind building automation and electronic monitoring of technical building systems and should give confidence to occupants about the actual savings of those new enhanced-functionalities. The smart readiness indicator is particularly beneficial for large buildings with a high energy demand. For other buildings, the scheme for rating the smart readiness of buildings should be optional for Member States.(57)A digital building twin is an interactive and dynamic simulation that reflects the real-time status and behaviour of a physical building. By incorporating real-time data from sensors, smart meters and other sources, a digital building twin provides a holistic view of the building’s performance, including energy consumption, temperature, humidity, occupancy levels, and more and can be used to monitor and manage the building’s energy consumption. Where a digital building twin is available, it should be taken into account, in particular for the smart readiness indicator.(58)Access to sufficient funding is crucial to meet the 2030 and 2050 energy and climate targets. Union financial instruments and other measures have been put into place or adapted with the aim of supporting the energy performance of buildings. The most recent initiatives to increase the availability of financing at Union level include, inter alia, the "Renovate" flagship component of the Recovery and Resilience Facility, in particular the REPowerEU plan, and the Social Climate Fund established by Regulation (EU) 2023/955 of the European Parliament and of the CouncilRegulation (EU) 2023/955 of the European Parliament and of the Council of 10 May 2023 establishing a Social Climate Fund and amending Regulation (EU) 2021/1060 (OJ L 130, 16.5.2023, p. 1)..(59)Union financial instruments should be used to give practical effect to the objectives of this Directive, without replacing national measures. In particular, due to the scale of the renovation effort needed, they should be used for providing appropriate and innovative means of financing to catalyse investment in the energy performance of buildings. They could play an important role in the development of national, regional and local energy efficiency funds, instruments and mechanisms which deliver such financing possibilities to private property owners, to small and medium-sized enterprises (SMEs) and to energy efficiency service companies.(60)Financial mechanisms, incentives and the mobilisation of financial institutions for energy renovations in buildings should play a central role in national building renovation plans and be actively promoted by Member States. Such measures should include encouraging energy-efficient mortgages for certified energy-efficient building renovations, promoting investments for public bodies in an energy-efficient building stock, for example by public-private partnerships or energy performance contracts or reducing the perceived risk of the investments. Information about available funding and financial tools should be made available to the public in an easily accessible and transparent manner. Member States should encourage financial institutions to promote targeted financial products, grants and subsidies to improve the energy performance of buildings housing vulnerable households, as well as to owners in worst-performing buildings with multiple residential building units and buildings in rural areas, and other groups for whom access to financing is difficult. The Commission should adopt a voluntary framework to help financial institutions target and increase lending volumes in accordance with the Union’s decarbonisation ambition and relevant energy targets.(61)Green mortgages and green loans can significantly contribute to transforming the economy and reducing carbon emissions.(62)Financing alone will not deliver on the renovation needs. Together with financing, setting up accessible and transparent advisory tools and assistance instruments such as one-stop shops that provide integrated energy renovation services or facilitators, as well as implementing other measures and initiatives such as those referred to in the Commission’s Smart Finance for Smart Buildings Initiative, is indispensable to provide the right enabling framework and break barriers to renovation. One-stop shops should provide technical assistance and be easily available to all those involved in building renovations, including homeowners and administrative, financial and economic actors, such as SMEs, including microenterprises.(63)Inefficient buildings are often linked to energy poverty and social problems. Vulnerable households are particularly exposed to increasing energy prices as they spend a larger proportion of their budget on energy products. By reducing excessive energy bills, building renovation can lift people out of energy poverty and can also prevent energy poverty. At the same time, building renovation does not come for free, and it is essential to ensure that the social impact of the costs for building renovation, in particular on vulnerable households, is kept in check. The Renovation Wave strategy should leave no one behind and be seized as an opportunity to improve the situation of vulnerable households, and a fair transition towards climate neutrality should be ensured. Therefore, financial incentives and other policy measures should as a priority target vulnerable households, people affected by energy poverty and people living in social housing, and Member States should take measures to prevent evictions because of renovation, such as caps on rent increases. Council Recommendation of 16 June 2022Council Recommendation of 16 June 2022 on ensuring a fair transition towards climate neutrality (OJ C 243, 27.6.2022, p. 35). provides a common framework and shared understanding of comprehensive policies and investments needed for ensuring that the transition is fair.(64)Microenterprises represent 94 % of companies active in the building sector. Together with small enterprises, they amount to 70 % of employment in the construction sector. They supply essential services and jobs locally. However, as microenterprises typically rely on fewer than 10 employees, they have limited resources to comply with regulatory requirements and rules attached to financial support programmes schemes. Energy communities, citizen-led initiatives and local authorities and energy agencies, while indispensable for delivering the Renovation Wave, face the same issues of lower administrative, financial and organisational capacities. This should not hamper the essential role of such entities and should be taken into account in the development of support and training programmes, with sufficient visibility and ease of access. Member States may actively support organisations with lower means with dedicated technical, financial and legal assistance.(65)Energy performance certificates for buildings have been in use since 2002. However, the use of different scales and formats hinders the comparability between different national schemes. Greater comparability of energy performance certificates across the Union facilitates the use of such certificates by financial institutions, thereby steering financing towards buildings with better energy performance and building renovation. The EU Taxonomy relies on the use of energy performance certificates and accentuates the need to improve their comparability. Introducing a common scale of energy performance classes and a common template should ensure sufficient comparability between energy performance certificates across the Union.(66)A number of Member States have recently modified their energy performance certification schemes. In order to avoid disruption, those Member States should have additional time to adapt their schemes.(67)In order to ensure that the energy performance of buildings can be taken into account by prospective buyers or tenants early in the process, buildings or building units which are offered for sale or rent should have an energy performance certificate, and the energy performance class and indicator should be stated in all advertisements. The prospective buyer or tenant of a building or building unit should, in the energy performance certificate, be given correct information about the energy performance of the building and practical advice on improving such performance. The energy performance certificate should also provide information on its primary and final energy consumption, energy needs, renewable energy production, greenhouse gas emissions, life-cycle GWP if available, and, as an option, its indoor environmental quality sensors or controls. The energy performance certificate should contain recommendations for the improvement of the energy performance of the building.(68)The monitoring of the building stock is facilitated by the availability of data collected by digital tools, thereby reducing administrative costs. Therefore, national databases for the energy performance of buildings should be set up, and the information contained therein should be transferred to the EU Building Stock Observatory.(69)Buildings owned or occupied by public bodies should set an example by showing that environmental and energy factors are taken into account. Those buildings should therefore be subject to energy certification on a regular basis. The dissemination to the public of information on the energy performance of buildings should be enhanced by clearly displaying those energy performance certificates, in particular in buildings which are occupied by public bodies and which are frequently visited by the public and certain non-residential buildings, such as town halls, schools, shops and shopping centres, supermarkets, restaurants, theatres, banks and hotels.(70)Recent years have seen a rise in the number of air-conditioning systems in European countries. That creates considerable problems at peak load times, increasing the cost of electricity and disrupting the energy balance. Priority should be given to strategies which enhance the thermal performance of buildings during the summer period. To that end, there should be a focus on measures which avoid overheating, such as shading and sufficient thermal capacity in the building construction, and further development and application of passive cooling techniques, primarily those that improve indoor environmental quality, the micro-climate around buildings and the urban heat island effect.(71)Regular maintenance and inspection of heating systems, ventilation systems and air-conditioning systems by qualified personnel contributes to maintaining their correct adjustment in accordance with the product specification and in that way ensures optimal performance from an environmental, safety and energy point of view. An independent assessment of the entire heating system, ventilation system and air-conditioning system should occur at regular intervals during its lifecycle in particular before its replacement or upgrading. Inspections should address the parts of the systems that are accessible either directly or indirectly through available non-destructive methods. In order to minimise the administrative burden on building owners and tenants, Member States should endeavour to combine inspections and certifications as far as possible. Where a ventilation system is installed, its sizing and its capabilities to optimise its performance under typical or average operating conditions relevant for the specific and current use of the building should also be assessed.(72)Where the system to be inspected is based on fossil fuels, the inspection should include a basic assessment of the feasibility to reduce the on-site use of fossil fuels, for example by integrating renewable energy, changing energy source, or replacing or adjusting the existing systems. In order to reduce the burden on users, that assessment should not be repeated if such recommendations are already documented, in the context of an energy performance certificate, renovation passports, energy audit, recommendations from the manufacturer or other means of providing advice in an equivalent official document or if the replacement of the system is already planned.(73)Some heating systems involve a high risk of carbon monoxide intoxication, depending on the type of heat generator (boiler, heat pump), the type of fuel (coal, oil, biomass, gas) or the location of the heat generator (such as within living spaces or in spaces not properly ventilated). Inspections of such systems provide a good opportunity for managing those risks.(74)A common approach to the energy performance certification of buildings, renovation passports, smart readiness indicators and to the inspection of heating systems and air-conditioning systems, carried out by qualified or certified accredited experts, whose independence is to be guaranteed on the basis of objective criteria, will contribute to a level playing field as regards efforts made in Member States related to energy savings in the buildings sector and will introduce transparency for prospective owners or users with regard to energy performance in the Union property market. Experts should benefit from using test equipment certified in accordance with EN and ISO standards. In order to ensure the quality of energy performance certificates, renovation passports, smart readiness indicators and of the inspection of heating systems and air-conditioning systems throughout the Union, an independent control system should be established in each Member State.(75)A sufficient number of reliable professionals competent in the field of energy renovation should be available to ensure sufficient capacity to carry out quality renovation works at the required scale. Member States should therefore, where appropriate and feasible, put in place certification schemes for integrated renovation works, which require expertise in various building elements or systems such as building insulation, electricity and heating systems and the installation of solar technologies; professionals involved may include designers, general contractors, specialist contractors and installers.(76)Since local and regional authorities are critical for the successful implementation of this Directive, they should be consulted and involved, as and when appropriate in accordance with applicable national law, on planning issues, the development of programmes to provide information, training and awareness-raising, and on the implementation of this Directive at national or regional level. Such consultations may also serve to promote the provision of adequate guidance to local planners and building inspectors to carry out the necessary tasks. Furthermore, Member States should enable and encourage architects, planners and engineers to properly consider the optimal combination of improvements in energy efficiency, use of energy from renewable sources and use of district heating and cooling when planning, designing, building and renovating industrial or residential areas, including building modelling and simulation technologies.(77)Installers and builders are critical for the successful implementation of this Directive. Therefore, an adequate number of installers and builders should, through training and other measures, have the appropriate level of competence for the installation and integration of the energy-efficient and renewable energy technology required.(78)In order to further the aim of improving the energy performance of buildings, the power to adopt acts in accordance with Article 290 TFEU should be delegated to the Commission in respect of the adaptation to technical progress of certain parts of the general framework set out in Annex I, in respect of the establishment of a comparative methodology framework for calculating cost-optimal levels of minimum energy performance requirements, in respect of setting out a Union framework for the national calculation of life-cycle GWP with a view to achieving climate neutrality, in respect of a Union scheme for rating the smart readiness of buildings and to effectively encourage financial institutions to increase volumes provided for energy performance renovations by means of a comprehensive portfolio framework for voluntary use by financial institutions. It is of particular importance that the Commission carry out appropriate consultations during its preparatory work, including at expert level, and that those consultations be conducted in accordance with the principles laid down in the Interinstitutional Agreement of 13 April 2016 on Better Law-MakingOJ L 123, 12.5.2016, p. 1.. In particular, to ensure equal participation in the preparation of delegated acts, the European Parliament and the Council receive all documents at the same time as Member States’ experts, and their experts systematically have access to meetings of Commission expert groups dealing with the preparation of delegated acts.(79)In order to ensure an effective implementation of the provisions laid down in this Directive, the Commission supports Member States through various tools, such as the Technical Support Instrument established by Regulation (EU) 2021/240 of the European Parliament and of the CouncilRegulation (EU) 2021/240 of the European Parliament and of the Council of 10 February 2021 establishing a Technical Support Instrument (OJ L 57, 18.2.2021, p. 1). providing tailor-made technical expertise to design and implement reforms, including those aimed at increasing the annual energy renovation rate of residential and non-residential buildings by 2030 and to foster deep energy renovations. The technical support relates to, for example, strengthening of administrative capacity, supporting policy development and implementation, and sharing of relevant best practices.(80)Since the objectives of this Directive, namely improving the energy performance of buildings and reducing the greenhouse gas emissions from buildings, cannot be sufficiently achieved by the Member States, due to the complexity of the buildings sector and the inability of the national housing markets to adequately address the challenges of energy efficiency, but can rather, by reason of the scale and the effects of the action, be better achieved at Union level, the Union may adopt measures, in accordance with the principle of subsidiarity as set out in Article 5 of the Treaty on European Union. In accordance with the principle of proportionality as set out in that Article, this Directive does not go beyond what is necessary in order to achieve those objectives.(81)The legal basis of this initiative empowers the Union to establish the measures necessary to achieve the objectives of the Union with regard to policy on energy. The proposal contributes to the Union’s energy policy objectives outlined in Article 194(1) TFEU, in particular improving the energy performance of buildings and reducing their greenhouse gas emissions, which contributes to preserving and improving the environment.(82)In accordance with point 44 of the Interinstitutional Agreement on Better Law-Making, Member States should draw up, for themselves and in the interest of the Union, their own tables, illustrating, as far as possible, the correlation between this Directive and the transposition measures, and make them public. In accordance with the Joint Political Declaration of 28 September 2011 of Member States and the Commission on explanatory documents, Member States have undertaken to accompany, in justified cases, the notification of their transposition measures with one or more documents explaining the relationship between the components of a directive and the corresponding parts of national transposition instruments. With regard to this Directive, the legislator considers the transmission of such documents to be justified, in particular following the judgment of the Court of Justice of the European Union in Case C-543/17Judgment of the Court (Grand Chamber) of 8 July 2019, European Commission v Kingdom of Belgium, C-543/17, ECLI:EU:C:2019:573..(83)The obligation to transpose this Directive into national law should be confined to those provisions which represent a substantive amendment as compared to the earlier Directive. The obligation to transpose the provisions which are unchanged arises under the earlier Directive.(84)This Directive should be without prejudice to the obligations of the Member States relating to the time-limits for the transposition into national law and the dates of application of the Directives set out in Part B of Annex VIII,HAVE ADOPTED THIS DIRECTIVE:
Article 1Subject matter1.This Directive promotes the improvement of the energy performance of buildings and the reduction of greenhouse gas emissions from buildings within the Union, with a view to achieving a zero-emission building stock by 2050, taking into account the outdoor climatic conditions, the local conditions, the requirements for indoor environmental quality, and cost-effectiveness.2.This Directive lays down requirements as regards:(a)the common general framework for a methodology for calculating the integrated energy performance of buildings and building units;(b)the application of minimum energy performance requirements to new buildings and new building units;(c)the application of minimum energy performance requirements to:(i)existing buildings and existing building units that are undergoing major renovation;(ii)building elements that form part of the building envelope and that have a significant impact on the energy performance of the building envelope when they are retrofitted or replaced;(iii)technical building systems where they are installed, replaced or upgraded;(d)the application of minimum energy performance standards to existing buildings and existing building units, in accordance with Articles 3 and 9;(e)the calculation and disclosure of the life-cycle global warming potential of buildings;(f)solar energy in buildings;(g)renovation passports;(h)national building renovation plans;(i)sustainable mobility infrastructure in and adjacent to buildings;(j)smart buildings;(k)energy performance certification of buildings or building units;(l)regular inspection of heating systems, ventilation systems and air-conditioning systems in buildings;(m)independent control systems for energy performance certificates, renovation passports, smart readiness indicators and inspection reports;(n)the indoor environmental quality performance of buildings.3.The requirements laid down in this Directive are minimum requirements and shall not prevent any Member State from maintaining or introducing more stringent measures, provided that such measures are compatible with Union law. Those measures shall be notified to the Commission.
Article 2DefinitionsFor the purposes of this Directive, the following definitions apply:(1)"building" means a roofed construction having walls, for which energy is used to condition the indoor environment;(2)"zero-emission building" means a building with a very high energy performance, as determined in accordance with Annex I, requiring zero or a very low amount of energy, producing zero on-site carbon emissions from fossil fuels and producing zero or a very low amount of operational greenhouse gas emissions, in accordance with Article 11;(3)"nearly zero-energy building" means a building with a very high energy performance, as determined in accordance with Annex I, which is no worse than the 2023 cost-optimal level reported by Member States pursuant to Article 6(2) and where the nearly zero or very low amount of energy required is covered to a very significant extent by energy from renewable sources, including energy from renewable sources produced on-site or energy from renewable sources produced nearby;(4)"minimum energy performance standards" means rules that require existing buildings to meet an energy performance requirement as part of a wide renovation plan for a building stock or at a trigger point on the market such as sale, rent, donation or change of purpose within the cadastre or land registry, in a period of time or by a specific date, thereby triggering the renovation of existing buildings;(5)"public bodies" means public bodies as defined in Article 2, point (12), of Directive (EU) 2023/1791;(6)"technical building system" means technical equipment of a building or building unit for space heating, space cooling, ventilation, domestic hot water, built-in lighting, building automation and control, on-site renewable energy generation and energy storage, or a combination thereof, including those systems using energy from renewable sources;(7)"building automation and control system" means a system comprising all products, software and engineering services that can support energy-efficient, economical and safe operation of technical building systems through automatic controls and by facilitating the manual management of those technical building systems;(8)"energy performance of a building" means the calculated or metered amount of energy needed to meet the energy demand associated with a typical use of the building, which includes energy used for heating, cooling, ventilation, domestic hot water and lighting;(9)"primary energy" means energy from renewable and non-renewable sources which has not undergone any conversion or transformation process;(10)"metered" means measured by a relevant device, such as an energy meter, a power meter, a power metering and monitoring device, or an electricity meter;(11)"non-renewable primary energy factor" means an indicator that is calculated by dividing the primary energy from non-renewable sources for a given energy carrier, including the delivered energy and the calculated energy overheads of delivery to the points of use, by the delivered energy;(12)"renewable primary energy factor" means an indicator that is calculated by dividing the primary energy from renewable sources from an on-site, nearby or distant energy source that is delivered via a given energy carrier, including the delivered energy and the calculated energy overheads of delivery to the points of use, by the delivered energy;(13)"total primary energy factor" means the sum of renewable and non-renewable primary energy factors for a given energy carrier;(14)"energy from renewable sources" means energy from renewable non-fossil sources, namely wind, solar (solar thermal and solar photovoltaic) and geothermal energy, osmotic energy, ambient energy, tide, wave and other ocean energy, hydropower, biomass, landfill gas, sewage treatment plant gas, and biogas;(15)"building envelope" means the integrated elements of a building which separate its interior from the outdoor environment;(16)"building unit" means a section, floor or apartment within a building which is designed or altered to be used separately;(17)"building element" means a technical building system or an element of the building envelope;(18)"residential building or building unit" means a room or suite of rooms in a permanent building or a structurally separated part of a building which is designed for all-year habitation by one private household;(19)"renovation passport" means a tailored roadmap for the deep renovation of a specific building in a maximum number of steps that will significantly improve its energy performance;(20)"deep renovation" means a renovation which is in line with the "energy efficiency first" principle, which focuses on essential building elements and which transforms a building or building unit:(a)before 1 January 2030, into a nearly zero-energy building;(b)from 1 January 2030, into a zero-emission building;(21)"staged deep renovation" means a deep renovation carried out in a maximum number of steps, asset out in a renovation passport;(22)"major renovation" means the renovation of a building where:(a)the total cost of the renovation relating to the building envelope or the technical building systems is higher than 25 % of the value of the building, excluding the value of the land upon which the building is situated; or(b)more than 25 % of the surface of the building envelope undergoes renovation.Member States may choose to apply point (a) or (b);(23)"operational greenhouse gas emissions" means greenhouse gas emissions associated with the energy consumption of the technical building systems during the use and operation of the building;(24)"whole-life-cycle greenhouse gas emissions" means greenhouse gas emissions that occur over the whole life cycle of a building, including the production and transport of construction products, construction-site activities, the use of energy in the building and replacement of construction products, as well as demolition, transport and management of waste materials and their reuse, recycling and final disposal;(25)"life-cycle global warming potential" or "life-cycle GWP" means an indicator which quantifies the global warming potential contributions of a building along its full life cycle;(26)"split incentives" means split incentives as defined in Article 2, point (54), of Directive (EU) 2023/1791;(27)"energy poverty" means energy poverty as defined in Article 2, point (52), of Directive (EU) 2023/1791;(28)"vulnerable households" means households in energy poverty or households, including lower middle-income households, that are particularly exposed to high energy costs and that lack the means to renovate the building that they occupy;(29)"European standard" means a standard adopted by the European Committee for Standardization, the European Committee for Electrotechnical Standardization or the European Telecommunications Standards Institute and made available for public use;(30)"energy performance certificate" means a certificate, recognised by a Member State or by a legal person designated by it, which indicates the energy performance of a building or building unit, calculated in accordance with a methodology adopted pursuant to Article 4;(31)"cogeneration" means the simultaneous generation in one process of thermal energy and electrical or mechanical energy;(32)"cost-optimal level" means the energy performance level which leads to the lowest cost during the estimated economic life cycle, where:(a)the lowest cost is determined taking into account:(i)the category and use of the building concerned;(ii)energy-related investment costs on the basis of official forecasts;(iii)maintenance and operating costs, including energy costs taking into account the cost of greenhouse gas allowances;(iv)environmental and health externalities of energy use;(v)earnings from energy produced on-site, where applicable;(vi)waste management costs, where applicable; and(b)the estimated economic life cycle is determined by each Member State and refers to the remaining estimated economic life cycle of a building where energy performance requirements are set for the building as a whole, or to the estimated economic life cycle of a building element where energy performance requirements are set for building elements.The cost-optimal level shall lie within the range of performance levels where the cost-benefit analysis calculated over the estimated economic life cycle is positive;(33)"recharging point" means a recharging point as defined in Article 2, point (48), of Regulation (EU) 2023/1804 of the European Parliament and of the CouncilRegulation (EU) 2023/1804 of the European Parliament and of the Council of 13 September 2023 on the deployment of alternative fuels infrastructure, and repealing Directive 2014/94/EU (OJ L 234, 22.9.2023, p. 1).;(34)"pre-cabling" means all measures that are necessary to enable the installation of recharging points, including data transmission, cables, cable routes and, where necessary, electricity meters;(35)"roofed car park" means a roofed construction, with at least three car parking spaces, that does not use energy to condition the indoor environment;(36)"micro-isolated system" means any system with consumption less than 500 GWh in the year 2022, where there is no connection with other systems;(37)"smart recharging" means smart recharging as defined in Article 2, second paragraph, point (14m), of Directive (EU) 2018/2001 of the European Parliament and of the CouncilDirective (EU) 2018/2001 of the European Parliament and of the Council of 11 December 2018 on the promotion of the use of energy from renewable sources (OJ L 328, 21.12.2018, p. 82).;(38)"bi-directional recharging" means bi-directional recharging as defined in Article 2, point (11), of Regulation (EU) 2023/1804;(39)"mortgage portfolio standards" means mechanisms incentivising mortgage lenders to establish a path to increase the median energy performance of the portfolio of buildings covered by their mortgages towards 2030 and 2050, and to encourage potential clients to improve the energy performance of their property in line with the Union’s decarbonisation ambition and relevant energy targets in the area of energy consumption in buildings, relying on the criteria for determining environmentally sustainable economic activities set out in Article 3 of Regulation (EU) 2020/852;(40)"pay-as-you-save financial scheme" means a loan scheme dedicated exclusively to energy performance improvements where a correlation is established in the designing of the scheme between the repayments on the loan and the achieved energy savings, also taking into account other economic factors such as the indexation of the energy cost, interest rates, increased asset value and loan re-financing;(41)"digital building logbook" means a common repository for all relevant building data, including data related to energy performance such as energy performance certificates, renovation passports and smart readiness indicators, as well as data related to the life-cycle GWP, which facilitates informed decision making and information sharing within the construction sector, and among building owners and occupants, financial institutions and public bodies;(42)"air-conditioning system" means a combination of the components required to provide a form of indoor air treatment, by which temperature is controlled or can be lowered;(43)"heating system" means a combination of the components required to provide a form of indoor air treatment, by which the temperature is increased;(44)"ventilation system" means the technical building system which provides outdoor air to a space by natural or mechanical means;(45)"heat generator" means the part of a heating system that generates useful heat for uses identified in Annex I, using one or more of the following processes:(a)the combustion of fuels in, for example, a boiler;(b)the Joule effect, taking place in the heating elements of an electric resistance heating system;(c)capturing heat from ambient air, ventilation exhaust air, or a water or ground heat source using a heat pump;(46)"cooling generator" means the part of an air-conditioning system that generates useful cooling for uses identified in Annex I;(47)"energy performance contracting" means energy performance contracting as defined in Article 2, point (33), of Directive (EU) 2023/1791;(48)"boiler" means the combined boiler body-burner unit, designed to transmit to fluids the heat released from burning;(49)"effective rated output" means the maximum calorific output, expressed in kW, specified and guaranteed by the manufacturer as being deliverable during continuous operation while complying with the useful efficiency indicated by the manufacturer;(50)"district heating" or "district cooling" means the distribution of thermal energy in the form of steam, hot water or chilled liquids, from a central or decentralised source of production through a network to multiple buildings or sites, for the use of space or process heating or cooling;(51)"useful floor area" means the area of the floor of a building needed as parameter to quantify specific conditions of use that are expressed per unit of floor area and for the application of the simplifications and the zoning and allocation or re-allocation rules;(52)"reference floor area" means the floor area used as reference size for the assessment of the energy performance of a building, calculated as the sum of the useful floor areas of the spaces within the building envelope specified for the energy performance assessment;(53)"assessment boundary" means the boundary where the delivered energy and exported energy are measured or calculated;(54)"on-site" means in or on a particular building or on the land on which that building is located;(55)"energy from renewable sources produced nearby" means energy from renewable sources, produced within a local or district-level perimeter of a particular building, which fulfils all of the following conditions:(a)it can be distributed and used only within that local and district-level perimeter through a dedicated distribution network;(b)it allows for the calculation of a specific primary energy factor valid only for the energy from renewable sources produced within that local or district-level perimeter; and(c)it can be used on-site through a dedicated connection to the energy production source, where that dedicated connection requires specific equipment for the safe supply and metering of energy for self-use of the building;(56)"services related to the energy performance of buildings" or "EPB services" means the services, such as heating, cooling, ventilation, domestic hot water and lighting and others for which the energy use is taken into account in the calculation of the energy performance of buildings;(57)"energy needs" means the energy to be delivered to, or extracted from, a conditioned space to maintain the intended space conditions during a given period of time, disregarding any technical building system inefficiencies;(58)"energy use" or "energy consumption" means energy input to a technical building system providing an EPB service intended to satisfy an energy need;(59)"self-use" means the use of energy from renewable sources produced on-site or energy from renewable sources produced nearby by on-site technical systems for EPB services;(60)"other on-site uses" means on-site uses other than EPB services, including appliances, miscellaneous and ancillary loads, or electro-mobility recharging points;(61)"calculation interval" means the discrete time interval used for the calculation of the energy performance;(62)"delivered energy" means energy, expressed per energy carrier, supplied to the technical building systems through the assessment boundary, to satisfy the uses taken into account or to produce the exported energy;(63)"exported energy" means the proportion of the renewable energy, expressed per energy carrier and per primary energy factor, that is exported to the energy grid instead of being used on-site for self-use or for other on-site uses;(64)"bicycle parking space" means a designated space for parking at least one bicycle;(65)"car park physically adjacent to a building" means a car park which is intended for the use of residents, visitors or workers of a building and which is located within the property area of the building or is in the direct vicinity of the building;(66)"indoor environmental quality" means the result of an assessment of the conditions inside a building that influence the health and wellbeing of its occupants, based upon parameters such as those relating to the temperature, humidity, ventilation rate and presence of contaminants.
Article 3National building renovation plan1.Each Member State shall establish a national building renovation plan to ensure the renovation of the national stock of residential and non-residential buildings, both public and private, into a highly energy-efficient and decarbonised building stock by 2050, with the objective to transform existing buildings into zero-emission buildings.2.Each national building renovation plan shall include:(a)an overview of the national building stock for different building types, including their share in the national building stock, construction periods and climatic zones, based, as appropriate, on statistical sampling and the national database for energy performance certificates pursuant to Article 22, an overview of market barriers and market failures and an overview of the capacities in the construction, energy efficiency and renewable energy sectors, and of the share of vulnerable households based, as appropriate, on statistical sampling;(b)a roadmap with nationally established targets and measurable progress indicators, including the reduction of the number of people affected by energy poverty, with a view to achieving the 2050 climate neutrality goal, in order to ensure a highly energy-efficient and decarbonised national building stock and the transformation of existing buildings into zero-emission buildings by 2050;(c)an overview of implemented and planned policies and measures, supporting the implementation of the roadmap pursuant to point (b);(d)an outline of the investment needs for the implementation of the national building renovation plan, the financing sources and measures, and the administrative resources for building renovation;(e)the thresholds for the operational greenhouse gas emissions and annual primary energy demand of a new or renovated zero-emission building pursuant to Article 11;(f)minimum energy performance standards for non-residential buildings on the basis of maximum energy performance thresholds pursuant to Article 9(1);(g)national trajectory for the renovation of the residential building stock, including the 2030 and 2035 milestones for average primary energy use in kWh/(m2.y) pursuant to Article 9(2); and(h)an evidence-based estimate of expected energy savings and wider benefits, including those related to indoor environmental quality.The roadmap referred to in point (b) of this paragraph shall include national targets for 2030, 2040 and 2050 as regards the annual energy renovation rate, the primary and final energy consumption of the national building stock and its operational greenhouse gas emission reductions; specific timelines for non-residential buildings to comply with lower maximum energy performance thresholds pursuant to Article 9(1), by 2040 and 2050, in line with the pathway for transforming the national building stock into zero-emission buildings; and an evidence-based estimate of expected energy savings and wider benefits, including those related to indoor environmental quality.Where an overview of specific policies and measures as referred to in point (c) or an outline of specific investment needs as referred to in point (d) is already included in the national energy and climate plans, a clear reference to the relevant parts of the national energy and climate plans may be included in the building renovation plan in place of a fully developed overview.3.Every five years, each Member State shall prepare and submit to the Commission its draft national building renovation plan, using the template set out in Annex II to this Directive. Each Member State shall submit its draft national building renovation plan as part of its draft integrated national energy and climate plan referred to in Article 9 of Regulation (EU) 2018/1999 and, where the Member States submits a draft update, as part of the draft update referred to in Article 14 of that Regulation.Notwithstanding the first subparagraph, Member States shall submit the first draft building renovation plan to the Commission by 31 December 2025.4.To support the development of its national building renovation plan, each Member State shall carry out a public consultation on its draft national building renovation plan prior to submitting it to the Commission. The public consultation shall involve in particular local and regional authorities and other socioeconomic partners, including civil society and bodies working with vulnerable households. Each Member State shall annex a summary of the results of its public consultation to its draft national building renovation plan. The public consultation may be integrated as part of the public consultation undertaken pursuant to Article 10 of Regulation (EU) 2018/1999.5.The Commission shall assess the draft national building renovation plans submitted pursuant to paragraph 3, in particular with regard to whether:(a)the level of ambition of the nationally established targets is sufficient and in line with the national commitments on climate and energy laid down in the national integrated energy and climate plans;(b)the policies and measures are sufficient to achieve the nationally established targets;(c)the allocation of budgetary and administrative resources is sufficient for the implementation of the plan;(d)the financing sources and measures referred to in paragraph 2, first subparagraph, point (d), of this Article are in line with the planned reduction of energy poverty referred to in paragraph 2, first subparagraph, point (b), of this Article;(e)the plans prioritise the renovation of worst-performing buildings in accordance with Article 9;(f)the public consultation pursuant to paragraph 4 has been sufficiently inclusive; and(g)the plans comply with the requirements of paragraph 1 and the template in Annex II.After consulting the Committee established by Article 33 of this Directive, the Commission may issue country-specific recommendations to Member States in accordance with Article 9(2) and Article 34 of Regulation (EU) 2018/1999.With regard to the first draft national building renovation plan, the Commission may issue country-specific recommendations to Member States no later than six months after the Member State has submitted that plan.6.In its national building renovation plan, each Member State shall take due account of any recommendations issued by the Commission on the draft national building renovation plan. If the Member State concerned does not address a recommendation or a substantial part thereof, it shall provide reasons to the Commission and shall make those reasons public.7.Every five years, each Member State shall submit its national building renovation plan to the Commission, using the template set out in Annex II to this Directive. Each Member State shall submit its national building renovation plan as part of its integrated national energy and climate plan referred to in Article 3 of Regulation (EU) 2018/1999 and, where a Member State submits an update, as part of the update referred to in Article 14 of that Regulation.Notwithstanding the first subparagraph, Member States shall submit the first national building renovation plan to the Commission by 31 December 2026.8.Each Member State shall annex the details of the implementation of its most recent long-term renovation strategy or national building renovation plan to its next national building renovation plan, indicating whether its national targets have been achieved.9.Each Member State shall include in its integrated national energy and climate progress reports, in accordance with Articles 17 and 21 of Regulation (EU) 2018/1999, information on the implementation of the national targets referred to in paragraph 2, point (b), of this Article. Every two years, the Commission shall include in its annual State of the Energy Union report submitted pursuant to Article 35 of Regulation (EU) 2018/1999, an overall progress report on the renovation of the national stock of residential and non-residential buildings, both public and private, in line with the roadmaps set out in the building renovation plans, based upon the information submitted by the Member States in their integrated national energy and climate progress reports. The Commission shall monitor annually the evolution of the energy performance of the Union building stock, on the basis of best available information from Eurostat and other sources, and publish the information through the EU Building Stock Observatory.
Article 4Adoption of a methodology for calculating the energy performance of buildingsMember States shall apply a methodology for calculating the energy performance of buildings in accordance with the common general framework set out in Annex I. That methodology shall be adopted at national or regional level.The Commission shall issue guidance for the calculation of the energy performance of transparent building elements that form part of the building envelope and the consideration of ambient energy.
Article 5Setting of minimum energy performance requirements1.Member States shall take the necessary measures to ensure that minimum energy performance requirements for buildings or building units are set with a view to at least achieving cost-optimal levels and, where relevant, more stringent reference values such as nearly zero-energy building requirements and zero-emission buildings requirements. The energy performance shall be calculated in accordance with the methodology referred to in Article 4. Cost-optimal levels shall be calculated in accordance with the comparative methodology framework referred to in Article 6.Member States shall take the necessary measures to ensure that minimum energy performance requirements are set for building elements that form part of the building envelope and that have a significant impact on the energy performance of the building envelope when they are replaced or retrofitted, with a view to achieving at least cost-optimal levels. Member States may set the requirements for building elements at a level that would facilitate the effective installation of low temperature heating systems in renovated buildings.When setting requirements, Member States may differentiate between new and existing buildings and between different categories of building.Those requirements shall take account of optimal indoor environmental quality, in order to avoid possible negative effects such as inadequate ventilation, as well as local conditions and the designated function and the age of the building.Member States shall review their minimum energy performance requirements at regular intervals which shall not be longer than five years and shall, if necessary, update them in order to reflect technical progress in the building sector, the results of the cost-optimal calculation set out in Article 6, and updated national energy and climate targets and policies.2.Member States may adapt the requirements referred to in paragraph 1 to buildings officially protected at national, regional or local level, as part of a designated environment or because of their special architectural or historical merit, in so far as compliance with certain requirements would unacceptably alter their character or appearance.3.Member States may decide not to set or apply the requirements referred to in paragraph 1 to the following categories of building:(a)buildings owned by the armed forces or central government and serving national defence purposes, apart from single living quarters or office buildings for the armed forces and other staff employed by national defence authorities;(b)buildings used as places of worship and for religious activities;(c)temporary buildings with a time of use of two years or less, industrial sites, workshops and non-residential agricultural buildings with low energy demand and non-residential agricultural buildings which are used by a sector covered by a national sectoral agreement on energy performance;(d)residential buildings which are used or intended to be used for either less than four months of the year or, alternatively, for a limited annual time of use and with an expected energy consumption of less than 25 % of what would be the result of all-year use;(e)stand-alone buildings with a total useful floor area of less than 50 m2.
Article 6Calculation of cost-optimal levels of minimum energy performance requirements1.The Commission is empowered to adopt delegated acts in accordance with Article 32 to supplement this Directive concerning the establishment and revision of a comparative methodology framework for calculating cost-optimal levels of minimum energy performance requirements for buildings and building elements.By 30 June 2025, the Commission shall revise the comparative methodology framework for calculating cost-optimal levels of minimum energy performance requirements in new buildings and existing buildings undergoing major renovation and for individual building elements. Those levels shall be in line with the national pathways set out in the national energy and climate plans submitted to the Commission pursuant to Article 14 of Regulation (EU) 2018/1999.The comparative methodology framework shall be laid down in accordance with Annex VII and shall differentiate between new and existing buildings and between different categories of building.2.Member States shall calculate cost-optimal levels of minimum energy performance requirements using the comparative methodology framework established in accordance with paragraph 1 and relevant parameters, such as climatic conditions and the practical accessibility of energy infrastructure, and compare the results of that calculation with the minimum energy performance requirements in force. When calculating the cost-optimal levels of minimum energy performance requirements, Member States may take into account the life-cycle GWP.Member States shall report to the Commission all input data and assumptions used for the calculations of cost-optimal levels of minimum energy performance requirements and the results of those calculations. To that end Member States shall use the template provided in Annex III to the Commission Delegated Regulation (EU) No 244/2012Commission Delegated Regulation (EU) No 244/2012 of 16 January 2012 supplementing Directive 2010/31/EU of the European Parliament and of the Council on the energy performance of buildings by establishing a comparative methodology framework for calculating cost-optimal levels of minimum energy performance requirements for buildings and building elements (OJ L 81, 21.3.2012, p. 18).. Member States shall update and submit those reports to the Commission at regular intervals, which shall not be longer than five years. The first report on the calculations on the basis of the revised methodology framework pursuant to paragraph 1 of this Article shall be submitted by 30 June 2028.3.If the result of the comparison performed in accordance with paragraph 2 shows that the minimum energy performance requirements in force in a Member State are less energy-efficient than cost-optimal levels of minimum energy performance requirements by more than 15 %, the Member State concerned shall adjust the minimum energy performance requirements in place within 24 months of the availability of the results of that comparison.4.The Commission shall publish a report on the progress of the Member States in reaching cost-optimal levels of minimum energy performance requirements.
Article 7New buildings1.Member States shall ensure that new buildings are zero-emission buildings in accordance with Article 11:(a)from 1 January 2028, new buildings owned by public bodies; and(b)from 1 January 2030, all new buildings;Until the application of the requirements under the first subparagraph, Member States shall ensure that all new buildings are at least nearly zero-energy buildings and meet the minimum energy performance requirements laid down in accordance with Article 5. Where public bodies intend to occupy a new building that they do not own, they shall aim for that building to be a zero-emission building.2.Member States shall ensure that the life-cycle GWP is calculated in accordance with Annex III and disclosed in the energy performance certificate of the building:(a)from 1 January 2028, for all new buildings with a useful floor area larger than 1000 m2;(b)from 1 January 2030, for all new buildings.3.The Commission is empowered to adopt delegated acts in accordance with Article 32 to amend Annex III to set out a Union framework for the national calculation of life-cycle GWP with a view to achieving climate neutrality. The first such delegated act shall be adopted by 31 December 2025.4.Member States may decide not to apply paragraphs 1 and 2 to buildings for which building permit applications or equivalent applications, including for change of use, have already been submitted by the dates pursuant to paragraphs 1 and 2.5.By 1 January 2027, Member States shall publish and notify to the Commission a roadmap detailing the introduction of limit values on the total cumulative life-cycle GWP of all new buildings and set targets for new buildings from 2030, considering a progressive downward trend, as well as maximum limit values, detailed for different climatic zones and building typologies.Those maximum limit values shall be in line with the Union’s objective of achieving climate neutrality.The Commission shall issue guidance, share evidence on existing national policies and offer technical support to Member States, at their request.6.Member States shall address, in relation to new buildings, the issues of optimal indoor environmental quality, adaptation to climate change, fire safety, risks related to intense seismic activity and accessibility for persons with disabilities. Member States shall also address carbon removals associated to carbon storage in or on buildings.
Article 8Existing buildings1.Member States shall take the necessary measures to ensure that, when buildings undergo major renovation, the energy performance of the building or the renovated part thereof is upgraded in order to meet minimum energy performance requirements set in accordance with Article 5 in so far as technically, functionally and economically feasible.Those requirements shall be applied to the renovated building or building unit as a whole. Additionally or alternatively, requirements may be applied to the renovated building elements.2.Member States shall in addition take the necessary measures to ensure that, when a building element that forms part of the building envelope and has a significant impact on the energy performance of the building envelope is retrofitted or replaced, the energy performance of the building element meets minimum energy performance requirements in so far as technically, functionally and economically feasible.3.Member States shall, in relation to buildings undergoing major renovation, encourage high-efficiency alternative systems, in so far as technically, functionally and economically feasible. Member States shall address, in relation to buildings undergoing major renovation, the issues of indoor environmental quality, adaptation to climate change, fire safety, risks related to intense seismic activity, the removal of hazardous substances including asbestos and accessibility for persons with disabilities.
Article 9Minimum energy performance standards for non-residential buildings and trajectories for progressive renovation of the residential building stock1.Member States shall establish minimum energy performance standards for non-residential buildings which ensure that those buildings do not exceed the specified maximum energy performance threshold, as referred to in the third subparagraph, expressed by a numeric indicator of primary or final energy use in kWh/(m2.y), by the dates specified in the fifth subparagraph.The maximum energy performance thresholds shall be established on the basis of the non-residential building stock on 1 January 2020, based on available information and, where appropriate, on statistical sampling. Member States shall exclude from the baseline non-residential buildings that they exempt pursuant to paragraph 6.Each Member State shall set a maximum energy performance threshold to the effect that 16 % of its national non-residential building stock is above that threshold (the "16 % threshold"). Each Member State shall also set a maximum energy performance threshold to the effect that 26 % of its national non-residential building stock is above that threshold (the "26 % threshold"). Member States may set the maximum energy performance thresholds with reference to the national non-residential building stock as a whole or per building type or category of building.Member States may set the thresholds at a level corresponding to a specific energy performance class, provided that they comply with the third subparagraph.The minimum energy performance standards shall ensure, at least, that all non-residential buildings are below:(a)the 16 % threshold from 2030; and(b)the 26 % threshold from 2033.Compliance of individual non-residential buildings with the thresholds shall be checked on the basis of energy performance certificates or, where appropriate, other available means.In their roadmaps as referred to in Article 3(1), point (b), Member States shall establish specific timelines for non-residential buildings to comply with lower maximum energy performance thresholds by 2040 and 2050, in line with the pathway for transforming the national building stock into zero-emission buildings.Member States may establish and publish criteria to exempt individual non-residential buildings, in light of the expected future use of those buildings, in light of serious hardship or in the case of an unfavourable cost-benefit assessment, from requirements in this paragraph. Any such criteria shall be clear, precise and stringent and shall ensure equal treatment between non-residential buildings. When establishing those criteria Member States shall enable the ex ante assessment of the potential share of non-residential buildings covered and shall avoid a disproportionate number of non-residential buildings from being exempted. Member States shall also report on the criteria as part of their national building renovation plans submitted to the Commission pursuant to Article 3.Where Member States establish criteria for exemptions pursuant to the eighth subparagraph, they shall achieve equivalent energy performance improvements in other parts of the non-residential building stock.Where the overall renovation necessary to achieve the energy performance thresholds specified in this paragraph has an unfavourable cost-benefit assessment for a given non-residential building, Member States shall require that, for that given non-residential building, at least those individual renovation measures with a favourable cost-benefit assessment are implemented.To the extent that the national non-residential building stock, or part of it, is seriously damaged by a natural disaster, a Member State may temporarily adjust the maximum energy performance threshold so that the energy renovation of damaged non-residential buildings replaces the energy renovation of other worst-performing non-residential buildings, whilst ensuring that a similar percentage of the non-residential building stock undergoes energy renovation. In that case, the Member State shall report the adjustment and its projected length in its national building renovation plan.2.By 29 May 2026, each Member State shall establish a national trajectory for the progressive renovation of the residential building stock in line with the national roadmap and the 2030, 2040 and 2050 targets contained in the Member State’s national building renovation plan and with the aim of transforming the national building stock into a zero-emission building stock by 2050. The national trajectory for the progressive renovation of the residential building stock shall be expressed as a decrease in the average primary energy use in kWh/(m2.y) of the entire residential building stock over the period from 2020 to 2050, and shall identify the number of residential buildings and residential building units or floor area to be renovated annually, including the number or floor area of the 43 % worst-performing residential buildings and residential building units.Member States shall ensure that the average primary energy use in kWh/(m2.y) of the entire residential building stock:(a)decreases by at least 16 % compared to 2020 by 2030;(b)decreases by at least 20-22 % compared to 2020 by 2035;(c)by 2040, and every 5 years thereafter, is equivalent to, or lower than the nationally determined value derived from a progressive decrease in the average primary energy use from 2030 to 2050, in line with the transformation of the residential building stock into a zero-emission building stock.Member States shall ensure that at least 55 % of the decrease in the average primary energy use referred to in the third subparagraph is achieved through the renovation of the 43 % worst-performing residential buildings. Member States may count the decrease in the average primary energy use achieved by the renovation of residential buildings affected by natural disasters such as earthquakes and floods towards the share achieved by means of the renovation of the 43 % worst-performing residential buildings.In their renovation efforts to achieve the required decrease in the average primary energy use of the entire residential building stock, Member States shall put in place measures such as minimum energy performance standards, technical assistance and financial support measures.In their renovation efforts, Member States shall not disproportionately exempt rental residential buildings or building units.Member States shall report in the national building renovation plans the methodology used and data gathered for estimating the values referred to in the second and third subparagraphs. As part of the assessment of national building renovation plans, the Commission shall monitor the achievement of the values referred to in the second and third subparagraphs, including the number of buildings and building units or floor area of the 43 % worst-performing residential buildings, and make recommendations where necessary. Those recommendations may include a more extensive use of minimum energy performance standards.The national trajectory for the progressive renovation of the residential building stock shall refer to data on the national residential building stock, based, as appropriate, on statistical sampling and energy performance certificates.If the average fossil share of energy use in residential buildings is lower than 15 %, Member States may adjust the levels laid down in the points (a) and (b) of the third subparagraph, to ensure that the average primary energy use in kWh/(m2.y) of the entire residential building stock by 2030, and every five years thereafter, is equivalent to, or lower than a nationally determined value derived from a linear decrease in the average primary energy use from 2020 to 2050, in line with the transformation of the residential building stock into a zero-emission building stock.3.In addition to primary energy use referred to in paragraphs 1 and 2 of this Article, Member States may establish additional indicators of non-renewable and renewable primary energy use, and of operational greenhouse gas emissions produced in kgCO2eq/(m2.y). In order to ensure reduction of operational greenhouse gas emissions, minimum energy performance standards shall take into account Article 15a(1) of Directive (EU) 2018/2001.4.In accordance with Article 17, Member States shall support compliance with minimum energy performance standards by all of the following measures:(a)providing appropriate financial measures, in particular those targeting vulnerable households, people affected by energy poverty or, where applicable, living in social housing, in accordance with Article 24 of Directive (EU) 2023/1791;(b)providing technical assistance, including through one-stop shops with a particular focus on vulnerable households and, where applicable, people living in social housing, in accordance with Article 24 of Directive (EU) 2023/1791;(c)designing integrated financing schemes which provide incentives for deep renovations and staged deep renovations, pursuant to Article 17;(d)removing non-economic barriers, including split incentives; and(e)monitoring social impacts, in particular on the most vulnerable households.5.Where a building is renovated in order to comply with a minimum energy performance standard, Member States shall ensure compliance with the minimum energy performance requirements for building elements pursuant to Article 5 and, in the case of major renovation, with the minimum energy performance requirements for existing buildings pursuant to Article 8.6.Member States may decide not to apply the minimum energy performance standards referred to in paragraphs 1 and 2 to the following categories of building:(a)buildings officially protected as part of a designated environment or because of their special architectural or historical merit, or other heritage buildings, in so far as compliance with the standards would unacceptably alter their character or appearance, or if their renovation is not technically or economically feasible;(b)buildings used as places of worship and for religious activities;(c)temporary buildings with a time of use of two years or less, industrial sites, workshops and non-residential agricultural buildings with low energy demand and non-residential agricultural buildings which are used by a sector covered by a national sectoral agreement on energy performance;(d)residential buildings which are used or intended to be used for either less than four months of the year or, alternatively, for a limited annual time of use and with an expected energy consumption of less than 25 % of what would be the result of all-year use;(e)stand-alone buildings with a total useful floor area of less than 50 m2;(f)buildings owned by the armed forces or central government and serving national defence purposes, apart from single living quarters or office buildings for the armed forces and other staff employed by national defence authorities.7.Member States shall take the measures necessary to ensure the implementation of minimum energy performance standards referred to in paragraphs 1 and 2 of this Article, including appropriate monitoring mechanisms and penalties in accordance with Article 34.When laying down the rules on penalties, Member States shall take into account the financial situation and access to adequate financial support of homeowners, in particular for vulnerable households.8.By 31 March 2025, the Commission shall, in support of the implementation of this Directive and taking due account of the principle of subsidiarity, present an analysis with particular regard to:(a)the effectiveness of, the appropriateness of the level of, the actual amount used from, and the types of instrument used with regard to structural funds and Union framework programmes, including funding from the European Investment Bank, for improving the energy performance of buildings, especially in housing;(b)the effectiveness of, the appropriateness of the level of, and the types of instrument and types of measure used with regard to funds from public finance institutions;(c)the coordination of Union and national funding and other types of measure that can act as leverage for stimulating investments in the energy performance of buildings, and the adequacy of such funding for achieving Union objectives.On the basis of that analysis, the Commission shall submit a report to the European Parliament and to the Council on the effectiveness and appropriateness of financing instruments towards the improvement of the energy performance of buildings, in particular the worst-performing ones.
Article 10Solar energy in buildings1.Member States shall ensure that all new buildings are designed to optimise their solar energy generation potential on the basis of the solar irradiance of the site, enabling the subsequent cost-effective installation of solar technologies.2.The permit-granting procedure for the installation of solar energy equipment set out in Article 16d of Directive (EU) 2018/2001, and simple-notification procedure for grid connections set out in Article 17 of that Directive shall apply to the installation of solar energy equipment on buildings.3.Member States shall ensure the deployment of suitable solar energy installations, if technically suitable and economically and functionally feasible, as follows:(a)by 31 December 2026, on all new public and non-residential buildings with useful floor area larger than 250 m2;(b)on all existing public buildings with useful floor area larger than:(i)2000 m2, by 31 December 2027;(ii)750 m2, by 31 December 2028;(iii)250 m2, by 31 December 2030;(c)by 31 December 2027, on existing non-residential buildings with useful floor area larger than 500 m2, where the building undergoes a major renovation or an action that requires an administrative permit for building renovations, works on the roof or the installation of a technical building system;(d)by 31 December 2029, on all new residential buildings; and(e)by 31 December 2029, on all new roofed car parks physically adjacent to buildings.In their national building renovation plans referred to in Article 3, Member States shall include policies and measures with regard to the deployment of suitable solar energy installations on all buildings.4.Member States shall establish, and make publicly available, criteria at national level for the practical implementation of the obligations set out in this Article, and for possible exemptions from those obligations for specific types of building, taking into account the principle of technological neutrality with regard to technologies not producing any on-site emissions and in accordance with the assessed technical and economic potential of the solar energy installations and the characteristics of the buildings covered by this obligation. Member States shall also take into account structural integrity, green roofs, and attic and roof insulation, where appropriate.In order to achieve the objectives of this Article and to take into account the issues linked to the stability of the electricity network, Member States shall include relevant stakeholders in the establishment of the criteria referred to in the first subparagraph of this paragraph.In the transposition of the obligations set out in the first subparagraph of paragraph 3, a Member State may use the measurement of buildings’ ground floor area instead of buildings’ useful floor area, provided that the Member State shows that this results in an equivalent amount of installed capacity of suitable solar energy installations on buildings.5.Member States shall put in place a framework providing the necessary administrative, technical and financial measures to support the deployment of solar energy in buildings, including in combination with technical building systems or efficient district heating systems.
Article 11Zero-emission buildings1.A zero-emission building shall not cause any on-site carbon emissions from fossil fuels. A zero-emission building shall, where economically and technically feasible, offer the capacity to react to external signals and adapt its energy use, generation or storage.2.Member States shall take the necessary measures to ensure that the energy demand of a zero-emission building complies with a maximum threshold.Member States shall set that maximum threshold for the energy demand of a zero-emission building with a view to achieving at least the cost-optimal levels established in the most recent national cost-optimal report pursuant to Article 6. Member States shall revise the maximum threshold every time that the cost-optimal levels are revised.3.The maximum threshold for the energy demand of a zero-emission building shall be at least 10 % lower than the threshold for total primary energy use established at Member State level for nearly zero-energy buildings on 28 May 2024.4.Member States may adjust the maximum threshold for the energy demand of a zero-emission building for renovated buildings, while complying with the respective provisions on cost optimality, and, where thresholds for renovated nearly zero-energy buildings have been established, the requirements of paragraph 3.5.Member States shall take the necessary measures to ensure that the operational greenhouse gas emissions of a zero-emission building comply with a maximum threshold established at the Member State level in their national building renovation plans. That maximum threshold may be set at different levels for new and renovated buildings.6.Member States shall notify the Commission about their maximum thresholds, including a description of the calculation methodology per building type and relevant outdoor climate designation, in accordance with Annex I. The Commission shall review the maximum thresholds and recommend their adaptation where appropriate.7.Member States shall ensure that the total annual primary energy use of a new or renovated zero-emission building is covered by:(a)energy from renewable sources generated on-site or nearby, fulfilling the criteria laid down in Article 7 of Directive (EU) 2018/2001;(b)energy from renewable sources provided from a renewable energy community within the meaning of Article 22 of Directive (EU) 2018/2001;(c)energy from an efficient district heating and cooling system in accordance with Article 26(1) of Directive (EU) 2023/1791; or(d)energy from carbon-free sources.Where it is not technically or economically feasible to fulfil the requirements laid down in this paragraph, the total annual primary energy use may also be covered by other energy from the grid complying with criteria established at national level.
Article 12Renovation passport1.By 29 May 2026, Member States shall introduce a scheme for renovation passports based on the common framework set out in Annex VIII.2.The scheme referred to in paragraph 1 shall be of voluntary use by owners of buildings and building units, unless the Member State decides to make it mandatory.Member States shall take measures to ensure that renovation passports are affordable and shall consider whether to provide financial support to vulnerable households wishing to renovate their buildings.3.Member States may allow for the renovation passport to be drawn up and issued jointly with the energy performance certificate.4.The renovation passport shall be issued in a digital format suitable for printing, by a qualified or certified expert, following an on-site visit.5.When the renovation passport is issued, a discussion with the expert referred to in paragraph 4 shall be suggested to the building owner to allow the expert to explain the best steps by which to transform the building into a zero-emission building well before 2050.6.Member States shall strive to provide a dedicated digital tool by means of which to prepare and, where appropriate, update the renovation passport. Member States may develop a complementary tool allowing building owners and building managers to simulate a draft simplified renovation passport and for them to update it once a renovation takes place or a building element is replaced.7.Member States shall ensure that the renovation passport can be uploaded to the national database for the energy performance of buildings set up pursuant to Article 22.8.Member States shall ensure that the renovation passport is stored in, or can be accessed via, where available, the digital building logbook.
Article 13Technical building systems1.Member States shall, for the purpose of optimising the energy use of technical building systems, set system requirements, using energy-saving technologies, in respect of the overall energy performance, the proper installation, the appropriate dimensioning, adjustment and control and, where appropriate, the hydronic balancing of the technical building systems which are installed in new or existing buildings. When setting up the requirements, Member States shall take account of design conditions and typical or average operating conditions.System requirements shall be set for new and for the replacement and upgrading of existing technical building systems and shall be applied in so far as technically, economically and functionally feasible.Member States may set requirements related to the greenhouse gas emissions of, or to the type of fuel used by heat generators or to the minimum part of renewable energy used for heating at building’s level, provided that such requirements do not constitute an unjustified market barrier.Member States shall ensure that the requirements they set for technical building systems reach at least the latest cost-optimal levels.2.Member States may set specific system requirements for technical building systems in order to facilitate the effective installation and operation of low temperature heating systems in new or renovated buildings.3.Member States shall require new buildings, where technically and economically feasible, to be equipped with self-regulating devices for the separate regulation of the temperature in each room or, where justified, in a designated heated or cooled zone of the building unit and, where appropriate, with hydronic balancing. The installation of such self-regulating devices and, where appropriate, hydronic balancing in existing buildings shall be required when heat generators or cooling generators are replaced, where technically and economically feasible.4.Member States shall set requirements for the implementation of adequate indoor environmental quality standards in buildings in order to maintain a healthy indoor climate.5.Member States shall require non-residential zero-emission buildings to be equipped with measuring and control devices for the monitoring and regulation of indoor air quality. In existing non-residential buildings, the installation of such devices shall be required, where technically and economically feasible, when a building undergoes a major renovation. Member States may require the installation of such devices in residential buildings.6.Member States shall ensure that, when a technical building system is installed, the overall energy performance of the altered part and, where relevant, of the complete altered system is assessed. The results shall be documented and passed on to the building owner, so that they remain available and can be used for the verification of compliance with the minimum requirements laid down pursuant to paragraph 1 and the issue of energy performance certificates.Member States shall take the necessary measures to ensure that the energy performance of technical building systems is optimised where they are retrofitted or replaced.Member States shall promote energy storage for renewable energy in buildings.Member States may provide for new incentives and funding to encourage the switch from fossil-fuel-based heating and cooling systems to non-fossil-fuel-based heating and cooling systems.7.Member States shall strive to replace stand-alone boilers powered by fossil fuels in existing buildings, in line with the national phase-out plans for fossil fuel boilers.8.The Commission shall issue guidance on what qualifies as a fossil fuel boiler.9.Member States shall lay down requirements to ensure that, where technically and economically feasible, non-residential buildings are equipped with building automation and control systems, as follows:(a)by 31 December 2024, non-residential buildings with an effective rated output for heating systems, air-conditioning systems, systems for combined space heating and ventilation, or systems for combined air conditioning and ventilation of over 290 kW;(b)by 31 December 2029, non-residential buildings with an effective rated output for heating systems, air-conditioning systems, systems for combined space heating and ventilation, or systems for combined air conditioning and ventilation of over 70 kW.10.The building automation and control systems shall be capable of:(a)continuously monitoring, logging, analysing and allowing for adjusting energy use;(b)benchmarking the building’s energy efficiency, detecting losses in efficiency of technical building systems, and informing the person responsible for the facilities or technical building management about opportunities for energy efficiency improvement;(c)allowing communication with connected technical building systems and other appliances inside the building, and being interoperable with technical building systems across different types of proprietary technologies, devices and manufacturers;(d)by 29 May 2026 monitoring of indoor environmental quality.11.Member States shall lay down requirements to ensure that, where technically, economically and functionally feasible, from 29 May 2026, new residential buildings and residential buildings undergoing major renovations are equipped with the following:(a)the functionality of continuous electronic monitoring that measures systems’ efficiency and informs building owners or managers in the case of a significant variation and when system servicing is necessary;(b)effective control functionalities to ensure optimum generation, distribution, storage, use of energy and, where applicable, hydronic balance;(c)a capacity to react to external signals and adjust the energy consumption.Member States may exclude single-family houses undergoing major renovations from the requirements laid down in this paragraph where the costs of installation exceed the benefits.12.Member States shall lay down requirements to ensure that, where technically and economically feasible, non-residential buildings with an effective rated output for heating systems, air-conditioning systems, systems for combined space heating and ventilation, or systems for combined air conditioning and ventilation of:(a)over 290 kW are equipped with automatic lighting controls by 31 December 2027;(b)over 70 kW are equipped with automatic lighting controls by 31 December 2029.The automatic lighting controls shall be suitably zoned and capable of occupancy detection.
Article 14Infrastructure for sustainable mobility1.With regard to new non-residential buildings with more than five car parking spaces and non-residential buildings undergoing major renovation, with more than five car parking spaces, Member States shall ensure:(a)the installation of at least one recharging point for every five car parking spaces;(b)the installation of pre-cabling for at least 50 % of car parking spaces and ducting, namely conduits for electric cables, for the remaining car parking spaces, to enable the installation at a later stage of recharging points for electric vehicles, electrically power-assisted cycles and other L-category vehicle types; and(c)the provision of bicycle parking spaces representing at least 15 % of average or 10 % of total user capacity of non-residential buildings, taking into account the space required also for bicycles with larger dimensions than standard bicycles.The first subparagraph shall apply where:(a)the car park is located inside the building, and, for major renovations, renovation measures include the car park or the electrical infrastructure of the building; or(b)the car park is physically adjacent to the building, and, for major renovations, renovation measures include the car park or the electrical infrastructure of the car park.Member States shall ensure that the pre-cabling and ducting referred to in point (b) of the first subparagraph are dimensioned so as to enable the simultaneous and efficient use of the required number of recharging points and support, where appropriate, the installation of a load or recharging management system, to the extent that this is technically and economically feasible and justifiable.By way of derogation from point (a) of the first subparagraph, for new office buildings and office buildings undergoing major renovation, with more than five parking spaces, Member States shall ensure the installation of at least one recharging point for every two parking spaces.2.With regard to all non-residential buildings with more than 20 car parking spaces, Member States shall, by 1 January 2027, ensure:(a)the installation of at least one recharging point for every 10 car parking spaces, or of ducting, namely conduits for electric cables, for at least 50 % of the car parking spaces to enable the installation at a later stage of recharging points for electric vehicles; and(b)the provision of bicycle parking spaces representing at least 15 % of average or 10 % of total user capacity of the building and with space required also for bicycles with larger dimensions than standard bicycles.For buildings owned or occupied by public bodies, Member States shall ensure the installation of pre-cabling for at least 50 % of car parking spaces by 1 January 2033.Member States may postpone the implementation of this requirement until 1 January 2029 for all non-residential buildings that have been renovated in the two years prior to 28 May 2024 in order to comply with the national requirements established in accordance with Article 8(3) of Directive 2010/31/EU.3.Member States may adjust requirements for the number of bicycle parking spaces in accordance with paragraphs 1 and 2 for specific categories of non-residential buildings that are not typically accessed by bicycles.4.With regard to new residential buildings with more than three car parking spaces and residential buildings undergoing major renovation, with more than three car parking spaces, Member States shall ensure:(a)the installation of pre-cabling for at least 50 % of car parking spaces and ducting, namely conduits for electric cables, for the remaining car parking spaces to enable the installation, at a later stage, of recharging points for electric vehicles, electrically power-assisted cycles and other L-category vehicle types; and(b)the provision of at least two bicycle parking spaces for every residential building unit.With regard to new residential buildings with more than three car parking spaces, Member States shall also ensure the installation of at least one recharging point.The first and second subparagraphs shall apply where:(a)the car park is located inside the building, and, for major renovations, renovation measures include the car park or the electric infrastructure of the building; or(b)the car park is physically adjacent to the building, and, for major renovations, renovation measures include the car park or the electrical infrastructure of the car park.By way of derogation from the first subparagraph, Member States may, subject to an assessment by local authorities and taking into account local characteristics, including demographical, geographical and climate conditions, adjust requirements for the number of bicycle parking spaces.Member States shall ensure that the pre-cabling referred to in point (a) of the first subparagraph is dimensioned to enable the simultaneous use of recharging points on all parking spaces. Where, in the case of major renovation, ensuring two bicycle parking spaces for every residential building unit is not feasible, Member States shall ensure as many bicycle parking spaces as appropriate.5.Member States may decide not to apply paragraphs 1, 2 and 4 of this Article to specific categories of building where:(a)the recharging infrastructure required would rely on micro-isolated systems or the buildings are situated in the outermost regions within the meaning of Article 349 TFEU where this would lead to substantial problems for the operation of the local energy system and would endanger the stability of the local grid; or(b)the cost of the recharging and ducting installations exceeds at least 10 % of the total cost of the major renovation of the building.6.Member States shall ensure that the recharging points referred to in paragraphs 1, 2 and 4 of this Article are capable of smart recharging and, where appropriate, bi-directional recharging and that they are operated on the basis of non-proprietary and non-discriminatory communication protocols and standards, in an interoperable manner, and in compliance with any European standards and delegated acts adopted pursuant to Article 21(2) and (3) of Regulation (EU) 2023/1804.7.Member States shall encourage that operators of non-publicly accessible recharging points operate them in accordance with Article 5(4) of Regulation (EU) 2023/1804, where applicable.8.Member States shall provide for measures in order to simplify, streamline and accelerate the procedure for the installation of recharging points in new and existing, residential and non-residential buildings, especially of co-owners’ associations, and remove regulatory barriers, including permitting and approval procedures from public authorities without prejudice to the property and tenancy law of the Member States. Member States shall remove barriers to the installation of recharging points in residential buildings with parking spaces, in particular the need to obtain consent from the landlord or co-owners for a private recharging point for own use. A request by tenants or co-owners to be allowed to install recharging infrastructure in a parking space may be refused only if there are serious and legitimate grounds for doing so.Without prejudice to their property and tenancy law, Member States shall assess administrative barriers regarding the application for the installation of a recharging point in a building with multiple residential building units at a tenants’ or a co-owners’ association.Member States shall ensure the availability of technical assistance for building owners and tenants wishing to install recharging points and bicycle parking spaces.With regard to residential buildings, Member States shall consider whether to introduce support schemes for the installation of recharging points, pre-cabling or ducting of parking spaces in line with the number of battery electric light-duty vehicles registered in their territory.9.Member States shall ensure the coherence of policies for buildings, active and green mobility, climate, energy, biodiversity and urban planning.10.By 31 December 2025, the Commission shall publish guidance for fire safety in car parks.
Article 15Smart readiness of buildings1.The Commission shall adopt delegated acts in accordance with Article 32 to supplement this Directive concerning an optional common Union scheme for rating the smart readiness of buildings. The rating shall be based on an assessment of the capabilities of a building or building unit to adapt its operation to the needs of the occupant, in particular concerning indoor environmental quality and the grid and to improve its energy efficiency and overall performance.In accordance with Annex IV, the optional common Union scheme for rating the smart readiness of buildings shall lay down:(a)the definition of the smart readiness indicator;(b)a methodology by which it is to be calculated.2.By 30 June 2026, the Commission shall submit a report to the European Parliament and the Council on the testing and implementation of the smart readiness indicator on the basis of the available results of the national test phases and other relevant projects.Taking into account the outcome of that report, the Commission shall, by 30 June 2027, adopt a delegated act in accordance with Article 32, supplementing this Directive by requiring the application of the common Union scheme for rating the smart readiness of buildings, in accordance with Annex IV, to non-residential buildings with an effective rated output for heating systems, air-conditioning systems, systems for combined space heating and ventilation, or systems for combined air-conditioning and ventilation of over 290 kW.3.The Commission shall, after having consulted the relevant stakeholders, adopt an implementing act detailing the technical arrangements for the effective implementation of the scheme referred to in paragraph 1 of this Article, including a timeline for a non-committal test phase at national level, and clarifying the complementary relation of the scheme to the energy performance certificates referred to in Article 19.That implementing act shall be adopted in accordance with the examination procedure referred to in Article 33(3).4.Provided that the Commission has adopted the delegated act referred to in paragraph 2, it shall, by 30 June 2027, adopt an implementing act detailing the technical arrangements for the effective implementation of the application of the scheme referred to in paragraph 2 to non-residential buildings with an effective rated output for heating systems, air-conditioning systems, systems for combined space heating and ventilation, or systems for combined air-conditioning and ventilation of over 290 kW.That implementing act shall be adopted in accordance with the examination procedure referred to in Article 33(3).
Article 16Data exchange1.Member States shall ensure that the building owners, tenants and managers can have direct access to their building systems’ data. Upon their consent, the access or data shall be made available to a third party, subject to the existing applicable rules and agreements. Member States shall facilitate the full interoperability of services and of data exchange within the Union in accordance with paragraph 5.For the purposes of this Directive, building systems’ data shall include at least all readily available data related to the energy performance of building elements, the energy performance of building services, the projected lifespan of the heating systems, where available, building automation and control systems, meters, measuring and control devices and recharging points for e-mobility and be linked, where available, to the digital building logbook.2.When laying down the rules regarding the management and exchange of data, taking into account the international standards and management format to data exchange, Member States or, where a Member State has so provided, the designated competent authorities, shall comply with the applicable Union law. The rules on the access and any charges shall not constitute a barrier or create discrimination for third parties to access building systems’ data.3.No additional costs shall be charged to the building owner, tenant or manager for access to their data or for a request to make their data available to a third party subject to the existing applicable rules and agreements. Member States shall be responsible for setting the relevant charges for access to data by other eligible parties such as financial institutions, aggregators, energy suppliers, energy services providers and national statistical institutes or other national authorities responsible for the development, production and dissemination of European statistics. Member States or, where applicable, the designated competent authorities, shall ensure that any charges imposed by regulated entities that provide data services are reasonable and duly justified. Member States shall incentivise the sharing of the relevant building systems’ data.4.The rules on access to data and data storage for the purposes of this Directive shall comply with the relevant Union law. The processing of personal data within the framework of this Directive shall be carried out in accordance with Regulation (EU) 2016/679 of the European Parliament and of the CouncilRegulation (EU) 2016/679 of the European Parliament and of the Council of 27 April 2016 on the protection of natural persons with regard to the processing of personal data and on the free movement of such data, and repealing Directive 95/46/EC (General Data Protection Regulation) (OJ L 119, 4.5.2016, p. 1)..5.By 31 December 2025, the Commission shall adopt implementing acts detailing interoperability requirements and non-discriminatory and transparent procedures for access to the data.Those implementing acts shall be adopted in accordance with the advisory procedure referred to in Article 33(2).The Commission shall issue a consultation strategy, setting out consultation objectives, targeted stakeholders and the consultation activities for the development of the implementing acts.
Article 17Financial incentives, skills and market barriers1.Member States shall provide appropriate financing, support measures and other instruments able to address market barriers in order to deliver the necessary investments identified in their national building renovation plan to transform their building stock into zero-emission buildings by 2050.2.Member States shall ensure that applications and procedures for public financing are simple and streamlined in order to facilitate access to financing, especially for households.3.Member States shall assess and, where appropriate, address barriers related to up-front costs of renovations.4.When designing financial support schemes for building renovation, Member States shall consider whether to use revenue-based parameters.Member States may use the national energy efficiency funds, where such funds are set up pursuant to Article 30 of Directive (EU) 2023/1791, to finance dedicated schemes and programmes for energy performance renovations.5.Member States shall take appropriate regulatory measures to remove non-economic barriers to building renovation. With regard to buildings with more than one building unit, such measures may include removing unanimity requirements in co-ownership structures, or allowing co-ownership structures to be direct recipients of financial support.6.Member States shall make best cost-effective use of national financing and financing available established at Union level, in particular the Recovery and Resilience Facility, the Social Climate Fund, the Cohesion fund, InvestEU, auctioning revenues from emission trading pursuant to Directive 2003/87/EC of the European Parliament and of the CouncilDirective 2003/87/EC of the European Parliament and of the Council of 13 October 2003 establishing a system for greenhouse gas emission allowance trading within the Union and amending Council Directive 96/61/EC (OJ L 275, 25.10.2003, p. 32). and other public funding sources. Those funding sources shall be deployed consistently with a path to achieving a zero-emission building stock by 2050.7.To support the mobilisation of investments, Member States shall promote the effective development and use of enabling funding and financial tools, such as energy efficiency loans and mortgages for building renovation, energy performance contracting, pay-as-you-save financial schemes, fiscal incentives, for example reduced tax rates on renovation works and materials, on-tax schemes, on-bill schemes, guarantee funds, funds targeting deep renovations, funds targeting renovations with a significant minimum threshold of targeted energy savings and mortgage portfolio standards. They shall guide investments into an energy-efficient public building stock, in line with Eurostat guidance on the recording of energy performance contracts in government accounts.Member States may also promote and simplify the use of public-private partnerships.8.Member States shall ensure that information about available funding and financial tools is made available to the public in an easily accessible and transparent manner, including by digital means.9.The enabling funding and financial tools may include renovation loans or guarantee funds for energy performance renovations, including in combination with relevant Union programmes, where applicable.10.By 29 May 2025, the Commission shall adopt a delegated act in accordance with Article 32 supplementing this Directive by establishing a comprehensive portfolio framework for voluntary use by financial institutions that supports lenders in targeting and increasing lending volumes provided in accordance with the Union’s decarbonisation ambition and relevant energy targets, in order to effectively encourage financial institutions to increase lending volumes provided for energy performance renovations. The actions set out in the comprehensive portfolio framework shall cover increasing lending volumes for energy renovations and shall include suggested safeguards to protect vulnerable households through blended funding solutions. The framework shall describe best practices to encourage lenders to identify and act upon the worst-performing buildings within their portfolios.11.Member States shall facilitate the aggregation of projects to enable investor access as well as packaged solutions for potential clients.Member States shall adopt measures that promote energy efficiency lending products for building renovations, such as green mortgages and green loans, secured and unsecured, and ensure that they are offered widely and in a non-discriminatory manner by financial institutions and, are visible and accessible to consumers. Member States shall ensure that banks and other financial institutions and investors receive information on opportunities to participate in the financing of the improvement of the energy performance of buildings.12.Member States shall put in place measures and financing to promote education and training with a view to ensuring that there is a sufficient workforce with the appropriate level of skills corresponding to the needs in the building sector, especially targeting SMEs, including microenterprises, as appropriate. One-stop shops established pursuant to Article 18 may facilitate access to such measures and financing.13.The Commission shall, where appropriate and upon request, assist Member States in setting up national or regional financial support programmes with the aim of increasing the energy performance of buildings, especially of existing buildings, including by supporting the exchange of best practice between the responsible national or regional authorities or bodies. Member States shall ensure that such programmes are developed in a way that they are accessible to organisations with lower administrative, financial, and organisational capacities.14.With due regard to vulnerable households, Member States shall link their financial measures for energy performance improvements and reduced greenhouse gas emissions in the renovation of buildings to the targeted or achieved energy savings and improvements, as determined by one or more of the following criteria:(a)the energy performance of the equipment or material used for the renovation and the related greenhouse gas emission reduction; in which case, the equipment or material used for the renovation is to be installed by an installer with the relevant level of certification or qualification and shall comply with at least minimum energy performance requirements for building elements or higher reference values for an improved energy performance of buildings;(b)standard values for the calculation of energy savings and greenhouse gas emission reduction in buildings;(c)the improvement achieved due to such renovation by comparing energy performance certificates issued before and after renovation;(d)the results of an energy audit;(e)the results of another relevant, transparent and proportionate method that shows the improvement in energy performance, for example by comparing the energy consumption before and after renovation with metering systems, provided it complies with the requirements set out in Annex I.15.From 1 January 2025, Member States shall not provide any financial incentives for the installation of stand-alone boilers powered by fossil fuels, with the exception of those selected for investment, before 2025, in accordance with Regulation (EU) 2021/241, Article 7(1), point (h)(i), third indent, of Regulation (EU) 2021/1058 and with Article 73 of Regulation (EU) 2021/2115 of the European Parliament and of the CouncilRegulation (EU) 2021/2115 of the European Parliament and of the Council of 2 December 2021 establishing rules on support for strategic plans to be drawn up by Member States under the common agricultural policy (CAP Strategic Plans) and financed by the European Agricultural Guarantee Fund (EAGF) and by the European Agricultural Fund for Rural Development (EAFRD) and repealing Regulations (EU) No 1305/2013 and (EU) No 1307/2013 (OJ L 435, 6.12.2021, p. 1)..16.Member States shall incentivise deep renovation and staged deep renovation with higher financial, fiscal, administrative and technical support. Where it is not technically or economically feasible to transform a building into a zero-emission building, a renovation resulting in at least a 60 % reduction of primary energy use shall be considered to be a deep renovation for the purposes of this paragraph. Member States shall incentivise sizeable programmes that address a high number of buildings, in particular the worst-performing buildings, such as through integrated district renovation programmes, and that result in an overall reduction of at least 30 % of primary energy use, with higher financial, fiscal, administrative and technical support, according to the level of performance achieved.17.Without prejudice to their national economic and social policies and to their systems of property law, Member States shall address the eviction of vulnerable households caused by disproportionate rent increases following energy renovation of their residential building or building unit.18.Financial incentives shall target, as a priority, vulnerable households, people affected by energy poverty and people living in social housing, in accordance with Article 24 of Directive (EU) 2023/1791.19.When providing financial incentives to owners of buildings or building units for the renovation of rented buildings or building units, Member States shall aim at financial incentives benefiting both the owners and the tenants. Member States shall introduce effective safeguards, to protect in particular vulnerable households, including by providing rent support or by imposing caps on rent increases, and may incentivise financial schemes that tackle the upfront costs of renovations, such as on-bill schemes, pay-as-you-save schemes or energy performance contracting, as referred to in point (33) of Article 2 and Article 29 of Directive (EU) 2023/1791.
Article 18One-stop shops for the energy performance of buildings1.Member States shall, in cooperation with competent authorities, and, where appropriate, private stakeholders, ensure the establishment and the operation of technical assistance facilities, including through inclusive one-stop shops for the energy performance of buildings, targeting all actors involved in building renovations, inter alia, home owners and administrative, financial and economic actors, such as SMEs, including microenterprises.Member States shall ensure that technical assistance facilities are available across their territory by establishing at least one one-stop shop:(a)per 80000 inhabitants;(b)per region;(c)in areas where the average age of the building stock is above the national average;(d)in areas where Member States intend to implement integrated district renovation programmes; or(e)in a location that can be reached within less than 90 minutes of average travel time, on the basis of the means of transport that is locally available.Member States may designate the one-stop shops established pursuant to Article 22(3), point (a), of Directive (EU) 2023/1791 as one-stop shops for the purposes of this Article.The Commission shall provide guidelines to establish those one-stop shops in accordance with Article 22(6) of Directive (EU) 2023/1791.2.The technical assistance facilities established pursuant to paragraph 1, shall:(a)provide streamlined information on technical and financial possibilities and solutions to households, SMEs including microenterprises, and public bodies;(b)provide holistic support to all households, with a particular focus on households affected by energy poverty and on worst-performing buildings, as well as to accredited companies and installers providing retrofit services, adapted to different housing typologies and geographical scope, and provide support covering the different stages of the retrofit project.3.One-stop shops established pursuant to paragraph 1 shall:(a)provide independent advice on the energy performance of buildings and may accompany integrated district renovation programmes;(b)offer dedicated services for vulnerable households, people affected by energy poverty and people in low-income households.
Article 19Energy performance certificates1.Member States shall lay down the necessary measures to establish a system of certification of the energy performance of buildings.The energy performance certificate shall include the energy performance of a building expressed by a numeric indicator of primary energy use in kWh/(m2.y), and reference values such as minimum energy performance requirements, minimum energy performance standards, nearly zero-energy building requirements and zero-emission building requirements, in order to make it possible for owners or tenants of the building or building unit to compare and assess its energy performance.2.By 29 May 2026, the energy performance certificate shall comply with the template in Annex V. It shall specify the energy performance class of the building, on a closed scale using only letters from A to G. The letter A shall correspond to zero-emission buildings, and the letter G shall correspond to the very worst-performing buildings in the national building stock at the time of the introduction of the scale. Member States that, on 29 May 2026, already designate zero-emission buildings as "A0" may continue to use that designation instead of class A. Member States shall ensure that the remaining classes (B to F or, where A0 is used, A to F) have an appropriate distribution of energy performance indicators among the energy performance classes.Member States may define an A+ energy performance class corresponding to buildings with a maximum threshold for energy demand which is at least 20 % lower than the maximum threshold for zero-emission buildings, and which generates more renewable energy on-site annually than its total annual primary energy demand. For existing buildings renovated to A+ class, Member States shall ensure that the life-cycle GWP is estimated and disclosed in the energy performance certificate of the building.Member States which have rescaled their energy performance classes on or after 1 January 2019 and before 28 May 2024, may postpone the rescaling of their energy performance classes until 31 December 2029.3.Member States shall ensure a common visual identity for energy performance certificates on their territory.4.Member States shall ensure the quality, reliability and affordability of energy performance certificates.Member States shall take measures to ensure that energy performance certificates are affordable and shall consider whether to provide financial support for vulnerable households.Member States shall ensure that energy performance certificates are issued in accordance with Article 20(1) and by independent experts on the basis of an on-site visit, which may be carried out, where appropriate, by virtual means with visual checks. The energy performance certificates shall be clear and easily legible, available in a machine-readable format and in accordance with the template in Annex V.5.The energy performance certificate shall include recommendations for the cost-effective improvement of the energy performance and the reduction of operational greenhouse gases emissions and the improvement of indoor environmental quality of a building or building unit, unless the building or building unit already achieves at least energy performance class A.The recommendations included in the energy performance certificate shall cover:(a)measures carried out in connection with a major renovation of the building envelope or technical building system or systems; and(b)measures for individual building elements independent of a major renovation of the building envelope or technical building system or systems.6.Where Member States provide for a renovation passport to be drawn up and issued jointly with the energy performance certificate pursuant to Article 12(3), the renovation passport shall substitute the recommendations pursuant to paragraph 5 of this Article.7.The recommendations included in the energy performance certificate shall be technically feasible for the specific building and shall provide an estimate for the energy savings and the reduction of operational greenhouse gas emissions. They may provide an estimate for the range of payback periods or costs and benefits over its economic life cycle and information on available financial incentives, administrative and technical assistance, as well as financial benefits which are broadly associated with the achievement of the reference values.8.The recommendations shall include an assessment of whether the heating systems, ventilation systems, air-conditioning systems and domestic hot-water systems can be adapted to operate at more efficient temperature settings, such as low temperature emitters for water based heating systems, including the required design of thermal power output and temperature and flow requirements.9.The recommendations shall include an assessment of the remaining lifespan of the heating system or air-conditioning system. Where relevant, the recommendations shall indicate possible alternatives for the replacement of the heating system or air-conditioning system, in line with the 2030 and 2050 climate targets, taking into account local and system-related circumstances.10.The energy performance certificate shall provide an indication as to where the owner or tenant of the building or building unit can receive more detailed information, including as regards the cost-effectiveness of the recommendations made in the energy performance certificate. The evaluation of cost-effectiveness shall be based on a set of standard conditions, such as the assessment of energy savings and underlying energy prices and a preliminary cost forecast. In addition, it shall contain information on the steps to be taken to implement the recommendations, the contact information of relevant one-stop shops and, where relevant, on financial support options. Other information on related topics, such as energy audits or incentives of a financial or other nature and financing possibilities, or advice on how to increase the climate resilience of the building, may also be provided to the owner or tenant of the building or building unit.11.Certification for building units may be based:(a)on a common certification of the whole building; or(b)on the assessment of another representative building unit with the same energy-relevant characteristics in the same building.12.Certification for single-family houses may be based on the assessment of another representative building of similar design and size with a similar actual energy performance quality if such correspondence can be guaranteed by the expert issuing the energy performance certificate.13.The validity of the energy performance certificate shall not exceed 10 years. Member States shall ensure that, where a building was issued a energy performance certificate below level C, building owners are invited to a one-stop shop to receive renovation advice on whichever of the following is the earlier:(a)immediately after the energy performance certificate of the building expires; or(b)five years after the issuance of the energy performance certificate.14.Member States shall make simplified procedures for updating an energy performance certificate available where only individual elements are upgraded, by means of single or standalone measures.Member States shall make simplified procedures for updating an energy performance certificate available where measures identified in a renovation passport are put in place or where a building digital twin, other certified methods, or data from certified tools determining the energy performance of a building are used.
Article 20Issue of energy performance certificates1.Member States shall ensure that a digital energy performance certificate is issued for:(a)buildings or building units when they are constructed, when they have undergone a major renovation, when they are sold, when they are rented out to a new tenant, or for which a rental contract is renewed;(b)existing buildings owned or occupied by public bodies.The requirement to issue an energy performance certificate shall not apply where a certificate, issued in accordance with either Directive 2010/31/EU or this Directive, for the building or building unit concerned is available and valid.Member States shall ensure that a paper version of the energy performance certificate is issued on request.2.Member States shall require that, when buildings or building units are constructed, have undergone a major renovation, or are sold or rented out, or when rental contracts for buildings or building units are renewed, the energy performance certificate is shown to the prospective tenant or buyer and handed over to the buyer or tenant.3.Where a building is sold or rented out in advance of construction or major renovation, Member States may require the seller to provide an assessment of its future energy performance, as a derogation from paragraphs 1 and 2; in that case, the energy performance certificate shall be issued at the latest once the building has been constructed or renovated and shall reflect the as-built state.4.Member States shall require that buildings or buildings units which are offered for sale or for rent have an energy performance certificate, and that the energy performance indicator and class of the energy performance certificate of the building or the building unit, as applicable, is stated in online and offline advertisements, including in property search portal websites.Member States shall carry out sample checks or other controls to ensure compliance with these requirements.5.The provisions of this Article shall be implemented in accordance with applicable national rules on joint ownership or common property.6.Member States may exclude the categories of building referred to in Article 5(3), points (b), (c) and (e), from the application of paragraphs 1, 2, 4 and 5 of this Article. Member States which chose to exclude from the obligations of this Article by 28 May 2024, residential buildings which are used or intended to be used for either less than four months of the year or, alternatively, for a limited annual time of use and with an expected energy consumption of less than 25 % of what would be the result of all-year use, may continue to do so.7.The possible effects of energy performance certificates in terms of legal proceedings, if any, shall be decided in accordance with national rules.8.Member States shall ensure that all energy performance certificates issued are uploaded to the database for the energy performance of buildings referred to in Article 22. The upload shall contain the full energy performance certificate, including all necessary data required for the calculation of the energy performance of the building.
Article 21Display of energy performance certificates1.Member States shall take measures to ensure that, where a building for which an energy performance certificate has been issued in accordance with Article 20(1) is occupied by public bodies and frequently visited by the public, the energy performance certificate is displayed in a prominent place clearly visible to the public.2.Member States shall require that in a non-residential building for which an energy performance certificate has been issued in accordance with Article 20(1), the energy performance certificate is displayed in a prominent and clearly visible place.3.The provisions of paragraphs 1 and 2 do not include an obligation to display the recommendations included in the energy performance certificate.
Article 22Databases for the energy performance of buildings1.Each Member State shall set up a national database for the energy performance of buildings which allows data to be gathered on the energy performance of individual buildings and on the overall energy performance of the national building stock. Such databases may consist of a set of interconnected databases.The database shall allow data to be gathered from all relevant sources related to energy performance certificates, inspections, the renovation passport, the smart readiness indicator and the calculated or metered energy consumption of the buildings covered. In order to populate the database, building typologies may also be gathered. Data may also be gathered and stored on both operational and embodied emissions and life-cycle GWP.2.The aggregated and anonymised data of building stock shall be made publicly available, in compliance with Union and national data protection rules. The data stored shall be machine-readable and accessible via an appropriate digital interface. Member States shall ensure easy and free-of-charge access to the full energy performance certificate for building owners, tenants and managers and to financial institutions as regards the buildings in their investment and lending portfolios, and, upon permission from the owner, also to independent experts. For buildings offered for rent or sale, Member States shall ensure access to the full energy performance certificate for prospective tenants or buyers that have been authorised by the owner of the building.3.Member States shall ensure that local authorities have access to relevant data on the energy performance of buildings on their territory as required to facilitate drafting of heating and cooling plans and include operational geographic information systems and the related databases, in accordance with Regulation (EU) 2016/679. Member States shall support the local authorities in obtaining necessary resources for data and information management.4.Member States shall make publicly available information on the share of buildings in the national building stock covered by energy performance certificates and aggregated or anonymised data on the energy performance, including the energy consumption, and, where available, the life-cycle GWP of the buildings covered. The public information shall be updated at least twice per year. Member States shall make anonymised or aggregated information available to public and research institutions such as national statistical institutes, upon request.5.At least once per year, Member States shall ensure the transfer of the information in the national database to the EU Building Stock Observatory. Member States may transfer the information more frequently.6.The Commission shall adopt implementing acts to establish common templates for the transfer of the information to the EU Building Stock Observatory. The first such implementing act shall be adopted by 30 June 2025.Those implementing acts shall be adopted in accordance with the examination procedure referred to in Article 33(3).7.For the purpose of ensuring coherence and consistency of information, Member States shall ensure that the national database for the energy performance of buildings is interoperable and integrated with other administrative databases containing information on buildings, such as the national building cadastre or land registry and digital building logbooks.
Article 23Inspections1.Member States shall lay down the necessary measures to establish regular inspections of the accessible parts of heating systems, ventilation systems and air-conditioning systems, including any combination thereof, with an effective rated output of over 70 kW. The effective rating of the system shall be based on the sum of the rated output of the heat generators and cooling generators.2.Member States may establish separate inspection schemes for the inspections of residential and non-residential systems.3.Member States may set different inspection frequencies depending on the type and effective rated output of the system whilst taking into account the costs of the inspection of the system and the estimated energy cost savings that may result from the inspection. Systems shall be inspected at least every five years. Systems with generators of an effective rated output of more than 290 kW shall be inspected at least every three years.4.The inspection shall include the assessment of the generator or generators, circulation pumps and, where appropriate, components of ventilation systems, air and water distribution systems, hydronic balancing systems and control systems. Member States may include in the inspection schemes any additional building systems identified under Annex I.The inspection shall include an assessment of the efficiency and sizing of the heat and cooling generator or generators and of the main components thereof compared with the requirements of the building and shall consider the capabilities of the system to optimise its performance under typical or average operating conditions, using available energy-saving technologies, and under changing conditions due to use variation. Where relevant, the inspection shall assess the feasibility of the system to operate under different and more efficient temperature settings, such as at low temperature for water-based heating systems, including via the design of thermal power output and temperature and flow requirements, while ensuring the safe operation of the system. The inspection shall, where relevant, include a basic assessment of the feasibility to reduce on-site use of fossil fuels, for example by integrating renewable energy, changing energy source or replace or adjust the existing systems.Where a ventilation system is installed, its sizing and its capabilities to optimise its performance under typical or average operating conditions relevant for the specific and current use of the building shall also be assessed.Where no changes have been made to the system or to the requirements of the building following an inspection carried out pursuant to this Article, Member States may choose not to require the assessment of the main component sizing or the assessment of operation under different temperatures to be repeated.5.Technical building systems that are explicitly covered by an agreed energy performance criterion or a contractual arrangement specifying an agreed level of energy efficiency improvement, such as energy performance contracting, or that are operated by a utility or network operator and therefore subject to performance monitoring measures on the system side, shall be exempt from the requirements laid down in paragraph 1, provided that the overall impact of such an approach is equivalent to that resulting from paragraph 1.6.Where the overall impact is equivalent to that resulting from paragraph 1, Member States may opt to take alternative measures such as financial support or the provision of advice to users concerning the replacement of generators, other modifications to the system and alternative solutions to assess the performance, efficiency and appropriate size of those systems.Before applying the alternative measures referred to in the first subparagraph of this paragraph, each Member State shall, by means of submitting a report to the Commission, document the equivalence of the impact of those measures to the impact of the measures referred to in paragraph 1, including in terms of energy savings and greenhouse gas emissions.7.Buildings that comply with Article 13(10) or (11) shall be exempt from the requirements laid down in paragraph 1 of this Article.8.Member States shall put in place inspection schemes or alternative measures such as digital tools and checklists to certify that the delivered construction and renovation works meet the designed energy performance and are compliant with the minimum energy performance requirements laid down in the building codes or equivalent regulations.9.Member States shall include a summarised analysis of the inspection schemes and their results as an annex to the national building renovation plan referred to in Article 3. Member States that have chosen the alternative measures indicated in paragraph 6 of this Article shall include a summarised analysis and the results of the alternative measures.
Article 24Reports on the inspection of heating systems, ventilation systems and air-conditioning systems1.An inspection report shall be issued after each inspection of a heating system, ventilation system or air-conditioning system. The inspection report shall contain the result of the inspection performed in accordance with Article 23 and include recommendations for the cost-effective improvement of the energy performance of the inspected system.Those recommendations may be based on a comparison of the energy performance of the system inspected with that of the best available feasible system, using energy-saving technologies, and a system of similar type for which all relevant components achieve the level of energy performance required by the applicable law. The recommendations shall, where relevant, include the results from the basic assessment of the feasibility to reduce on-site use of fossil fuels.The inspection report shall indicate any safety issue that was detected during inspection. However, the author of the report shall not be considered to be liable in relation to the detection or indication of any such safety issues.2.The inspection report shall be handed over to the owner or tenant of the building or building unit.3.The inspection report shall be uploaded into the national database for the energy performance of buildings pursuant to Article 22.
Article 25Independent experts1.Member States shall ensure that the energy performance certification of buildings, the establishment of renovation passports, the smart readiness assessment and the inspection of heating systems, ventilation systems and air-conditioning systems are carried out in an independent manner by qualified or certified experts, whether operating in a self-employed capacity or employed by public bodies or private enterprises.Experts shall be certified in accordance with Article 28 of Directive (EU) 2023/1791 taking into account their competence.2.Member States shall make available to the public information on training and certifications. Member States shall ensure that either regularly updated lists of qualified or certified experts or regularly updated lists of certified companies which offer the services of such experts are made available to the public.
Article 26Certification of building professionals1.Member States shall ensure the appropriate level of competence for building professionals carrying out integrated renovation works in accordance with Article 3 of, and Annex II to, this Directive and with Article 28 of Directive (EU) 2023/1791.2.Where appropriate and feasible, Member States shall ensure that certification or equivalent qualification schemes are available for providers of integrated renovation works where this is not covered by Article 18(3) of Directive (EU) 2018/2001 or Article 28 of Directive (EU) 2023/1791.
Article 27Independent control system1.Member States shall ensure that independent control systems for energy performance certificates are established in accordance with Annex VI, and that independent control systems for renovation passports, smart readiness indicators and reports on the inspection of heating systems, ventilation systems and air-conditioning systems are established. Member States may establish separate systems for the control of energy performance certificates, renovation passports, smart readiness indicators and reports on the inspection of heating systems, ventilation systems and air-conditioning systems.2.The Member States may delegate the responsibilities for implementing the independent control systems.Where the Member States decide to do so, they shall ensure that the independent control systems are implemented in compliance with Annex VI.3.Member States shall require the energy performance certificates, the renovation passports, the smart readiness indicators and the inspection reports referred to in paragraph 1 to be made available to the competent authorities or bodies on request.
Article 28ReviewThe Commission, assisted by the Committee referred to in Article 33, shall review this Directive by 31 December 2028, in light of the experience gained and progress made during its application, and, if necessary, make proposals.As part of that review, the Commission shall assess whether the application of this Directive in combination with other legislative instruments addressing energy performance and greenhouse gas emissions from buildings, in particular through carbon pricing, deliver sufficient progress towards achieving a fully decarbonised, zero-emission building stock by 2050, or whether further binding measures at Union level, in particular mandatory minimum energy performance standards across the whole building stock, need to be introduced, including in order to ensure that the values for 2030 and 2035 set out in Article 9(2) can be achieved. The Commission shall also assess the national roadmaps and in particular the planned limit values for the life-cycle GWP of new buildings pursuant to Article 7(4) and shall consider whether additional measures promoting a sustainable built environment are needed. The Commission shall also examine in what manner Member States could apply integrated district or neighbourhood approaches in Union building and energy efficiency policy, while ensuring that each building meets the minimum energy performance requirements, for example by means of integrated renovation programmes and overall renovation schemes applying to a number of buildings in a spatial context instead of a single building. The Commission shall also assess whether alternative indicators, such as final energy use and energy needs would be better suited for the purposes of Annex I.
Article 29Information1.Member States shall prepare and carry out information and awareness-raising campaigns. They shall take the necessary measures to inform the owners and tenants of buildings or building units and all relevant market actors, such as local and regional authorities and energy communities, of the different methods and practices that serve to enhance energy performance. In particular, Member States shall take the necessary measures to provide tailor-made information to vulnerable households. That information shall also be made available to local authorities and civil society organisations.2.Member States shall in particular provide information to the owners or tenants of buildings on energy performance certificates, including their purpose and objectives, on cost-effective measures and, where appropriate, financial instruments, to improve the energy performance of the building, and on replacing fossil fuel boilers with more sustainable alternatives. Member States shall provide the information through accessible and transparent advisory tools such as renovation advice and the one-stop shops established pursuant to Article 18, paying particular attention to vulnerable households.At the request of the Member States, the Commission shall assist Member States in staging information campaigns for the purposes of paragraph 1 and the first subparagraph of this paragraph, which may be dealt with in Union programmes.3.Member States shall ensure that guidance and training, including for under-represented groups, are made available, for those responsible for implementing this Directive. Such guidance and training shall address the importance of improving energy performance, and shall enable consideration of the optimal combination of improvements in energy efficiency, reduction of greenhouse gas emissions, use of energy from renewable sources and use of district heating and cooling when planning, designing, building and renovating industrial or residential areas. Such guidance and training may also address structural improvements, adaptation to climate change, fire safety, risks related to intense seismic activity, the removal of hazardous substances including asbestos, air pollutant emissions (including fine particulate matter), indoor environmental quality and accessibility for persons with disabilities. Member States shall endeavour to put in place measures to support training for local and regional authorities, renewable energy communities and other relevant actors, such as citizen-led renovation initiatives, to promote the objectives of this Directive.4.The Commission shall continuously improve its information services, in particular the website that has been set up as a European portal for energy efficiency in buildings directed towards citizens, professionals and authorities, in order to assist Member States in their information and awareness-raising efforts. Information displayed on that website might include links to relevant Union law and national, regional and local rules, links to Europa websites that display the National Energy Efficiency Action Plans, links to available financial instruments, as well as best practice examples at national, regional and local level, including with regard to the one-stop shops established pursuant to Article 18 of this Directive. In the context of the European Regional Development Fund, the Cohesion Fund and the Just Transition Fund established by Regulation (EU) 2021/1056 of the European Parliament and of the CouncilRegulation (EU) 2021/1056 of the European Parliament and of the Council of 24 June 2021 establishing the Just Transition Fund (OJ L 231, 30.6.2021, p. 1)., the Social Climate Fund, and the Recovery and Resilience Facility, the Commission shall continue and further intensify its information services with the aim of facilitating the use of available funds by providing assistance and information, including, in cooperation with the European Investment Bank, through the European Local Energy Assistance facility, to interested stakeholders, including national, regional and local authorities, on funding possibilities, taking into account the latest changes in the regulatory framework.
Article 30ConsultationIn order to facilitate the effective implementation of this Directive, Member States shall consult the stakeholders involved, including local and regional authorities, in accordance with the national law applicable and as relevant. Such consultation is of particular importance for the application of Article 29.
Article 31Adaptation of Annex I to technical progressThe Commission shall adopt delegated acts in accordance with Article 32 to amend this Directive concerning the adaptation of points 4 and 5 of Annex I to technical progress.
Article 32Exercise of the delegation1.The power to adopt delegated acts is conferred on the Commission subject to the conditions laid down in this Article.2.The power to adopt delegated acts referred to in Articles 6, 7, 15, 17 and 31 shall be conferred on the Commission for an indeterminate period of time from 28 May 2024.3.The delegation of power referred to in Articles 6, 7, 15, 17 and 31 may be revoked at any time by the European Parliament or by the Council. A decision to revoke shall put an end to the delegation of the power specified in that decision. It shall take effect the day following the publication of the decision in the Official Journal of the European Union or at a later date specified therein. It shall not affect the validity of any delegated acts already in force.4.Before adopting a delegated act, the Commission shall consult experts designated by each Member State in accordance with the principles laid down in the Interinstitutional Agreement of 13 April 2016 on Better Law-Making.5.As soon as it adopts a delegated act, the Commission shall notify it simultaneously to the European Parliament and to the Council.6.A delegated act adopted pursuant to Article 6, 7, 15, 17 or 31 shall enter into force only if no objection has been expressed either by the European Parliament or the Council within a period of two months of notification of that act to the European Parliament and the Council or if, before the expiry of that period, the European Parliament and the Council have both informed the Commission that they will not object. That period shall be extended by two months at the initiative of the European Parliament or of the Council.
Article 33Committee procedure1.The Commission shall be assisted by a committee. That committee shall be a committee within the meaning of Regulation (EU) No 182/2011 of the European Parliament and of the CouncilRegulation (EU) No 182/2011 of the European Parliament and of the Council of 16 February 2011 laying down the rules and general principles concerning mechanisms for control by Member States of the Commission’s exercise of implementing powers (OJ L 55, 28.2.2011, p. 13)..2.Where reference is made to this paragraph, Article 4 of Regulation (EU) No 182/2011 shall apply.3.Where reference is made to this paragraph, Article 5 of Regulation (EU) No 182/2011 shall apply.
Article 34PenaltiesMember States shall lay down the rules on penalties applicable to infringements of national provisions adopted pursuant to this Directive and shall take all measures necessary to ensure that they are implemented. The penalties provided for must be effective, proportionate and dissuasive. Member States shall, without delay, notify the Commission of those rules and of those measures and shall notify it, without delay, of any subsequent amendment affecting them.
Article 35Transposition1.Member States shall bring into force the laws, regulations and administrative provisions necessary to comply with Articles 1, 2 and 3, 5 to 29 and 32 and Annexes I, II and III and V to X by 29 May 2026. They shall immediately communicate the text of those measures and a correlation table to the Commission.Member States shall bring into force the laws, regulations and administrative provisions necessary to comply with Article 17(15) by 1 January 2025.When Member States adopt those measures, they shall contain a reference to this Directive or be accompanied by such a reference on the occasion of their official publication. They shall also include a statement that references in existing laws, regulations and administrative provisions to the Directive repealed by this Directive shall be construed as references to this Directive. Member States shall determine how such reference is to be made and how that statement is to be formulated.2.Member States shall communicate to the Commission the text of the main provisions of national law which they adopt in the field covered by this Directive.
Article 36RepealDirective 2010/31/EU, as amended by the acts listed in Part A of Annex IX, is repealed with effect from 30 May 2026, without prejudice to the obligations of the Member States relating to the time-limits for the transposition into national law and the dates of application of the Directives set out in Part B of Annex IX.References to the repealed Directive shall be construed as references to this Directive and shall be read in accordance with the correlation table in Annex X.
Article 37Entry into force and applicationThis Directive shall enter into force on the twentieth day following that of its publication in the Official Journal of the European Union.Articles 30, 31, 33 and 34 shall apply from 30 May 2026.
Article 38AddresseesThis Directive is addressed to the Member States.
Done at Strasbourg, 24 April 2024.For the European ParliamentThe PresidentR. MetsolaFor the CouncilThe PresidentM. MichelANNEX ICommon general framework for the calculation of the energy performance of buildings(referred to in Article 4)1.The energy performance of a building shall be determined on the basis of calculated or metered energy use and shall reflect typical energy use for space heating, space cooling, domestic hot water, ventilation, built-in lighting and other technical building systems. Member States shall ensure that the typical energy use is representative of actual operating conditions for each relevant typology and reflects the typical user behaviour. Where possible, typical energy use and typical user behaviour shall be based on available national statistics, building codes and metered data.Where metered energy use is the basis for calculating the energy performance of buildings, the calculation methodology shall be capable of identifying the influence of the behaviour of occupants and the local climate, which shall not be reflected in the result of the calculation. Metered energy use for the purpose of calculating the energy performance of buildings shall require readings of at least monthly intervals and must differentiate between energy carriers.Member States may use metered energy consumption under typical operating conditions to verify the correctness of the calculated energy use and enable comparison between calculated and actual performance. Metered energy consumption for the purposes of verification and comparison may be based on monthly readings.The energy performance of a building shall be expressed by a numeric indicator of primary energy use per unit of reference floor area per year, in kWh/(m2.y) for the purposes of both energy performance certification and compliance with minimum energy performance requirements. The methodology applied for the determination of the energy performance of a building shall be transparent and open to innovation.Member States shall describe their national calculation methodology on the basis of Annex A to the key European standards on the energy performance of buildings, namely (EN) ISO 52000-1, (EN) ISO 52003-1, (EN) ISO 52010-1, (EN) ISO 52016-1, (EN) ISO 52018-1, (EN) ISO 52120-1, EN 16798-1 and EN 17423 or superseding documents. This provision shall not constitute a legal codification of those standards.Member States shall take the necessary measures to ensure that, where buildings are supplied by district heating or cooling systems, the benefits of such supply are recognised and accounted for in the calculation methodology, in particular the renewable energy share, through individually certified or recognised primary energy factors.2.The energy needs and energy use for space heating, space cooling, domestic hot water, ventilation, lighting and other technical building systems shall be calculated using monthly, hourly or sub-hourly time calculation intervals in order to account for varying conditions that significantly affect the operation and performance of the system and the indoor conditions, and to optimise health, indoor air quality, including comfort levels, defined by Member States at national or regional level.Where product-specific regulations for energy-related products adopted under Directive 2009/125/EC include specific product information requirements for the purpose of calculating energy performance and life-cycle GWP under this Directive, national calculation methods shall not require additional information.The calculation of primary energy shall be based on regularly updated and forward-looking primary energy factors (distinguishing non-renewable, renewable and total) or weighting factors per energy carrier, which have to be recognised by the national authorities and taking into account the expected energy mix on the basis of its national energy and climate plan. Those primary energy factors or weighting factors may be based on national, regional or local information. Primary energy factors or weighting factors may be set on an annual, seasonal, monthly, daily or hourly basis or on more specific information made available for individual district systems.Primary energy factors or weighting factors shall be defined by Member States. The choices made and data sources shall be reported according to EN 17423 or any superseding document. Member States may opt for an average Union primary energy factor for electricity established pursuant to Directive (EU) 2023/1791 instead of a primary energy factor reflecting the electricity mix in the country.3.For the purpose of expressing the energy performance of a building, Member States shall define additional numeric indicators of total, non-renewable and renewable primary energy use, and of operational greenhouse gas emissions produced in kgCO2eq/(m2.y).4.The methodology shall be laid down taking into consideration at least the following aspects:(a)the following actual thermal characteristics of the building including its internal partitions:(i)thermal capacity;(ii)insulation;(iii)passive heating;(iv)cooling elements;(v)thermal bridges;(b)heating installation and domestic hot-water supply, including their insulation characteristics;(c)capacity of installed on-site renewable energy generation and energy storage;(d)air-conditioning installations;(e)natural and mechanical ventilation which may include air-tightness and heat recovery;(f)built-in lighting installation (mainly in the non-residential sector);(g)the design, positioning and orientation of the building, including outdoor climate;(h)passive solar systems and solar protection;(i)indoor climatic conditions, including the designed indoor climate;(j)internal loads;(k)building automation and control systems and their capabilities to monitor, control and optimise energy performance.5.The positive influence of the following aspects shall be taken into account:(a)local solar exposure conditions, active solar systems and other heating and electricity systems on the basis of energy from renewable sources;(b)electricity produced by cogeneration;(c)district or block heating and cooling systems;(d)natural lighting;(e)electrical storage systems;(f)thermal storage systems.6.For the purposes of the calculation of the energy performance of buildings, buildings should be adequately classified into the following categories:(a)single-family houses of different types;(b)apartment blocks;(c)offices;(d)educational buildings;(e)hospitals;(f)hotels and restaurants;(g)sports facilities;(h)wholesale and retail trade services buildings;(i)other types of energy-consuming buildings.ANNEX IITemplate for the national building renovation plans(referred to in Article 3)
This Directive Article 3Mandatory indicatorsOptional indicators
(a)Overview of the national building stockNumber of buildings and total floor area (m2):per building type (including public buildings and social housing)per energy performance classnearly zero-energy buildingsworst-performing buildings (including a definition)the 43 % worst-performing residential buildingsestimation of the share of buildings exempted pursuant to Article 9(6), point (b)Number of buildings and total floor area (m2):per building ageper building sizeper climatic zonedemolition (number and total floor area (m2))
Number of energy performance certificates:per building type (including public buildings)per energy performance classNumber of energy performance certificates:per construction period
Annual renovation rates: number and total floor area (m2)per building typeto nearly zero-energy and/or to zero-emission building levelsper renovation depth (weighted average renovation)public buildings
Primary and final annual energy consumption (ktoe):per building typeper end useEnergy savings (ktoe):residential buildingsnon-residential buildingspublic buildingsAverage primary energy use in kWh/(m2.y) for residential buildingsShare of renewable energy in the building sector (MW installed or GWh generated):for different usesReduction in energy costs (EUR) per household (average)Primary energy use of a building corresponding to the top 15 % (substantial contribution threshold) and the top 30 % (do no significant harm threshold) of the national building stock, as per Delegated Regulation (EU) 2021/2139Share of heating system in the building sector per boiler/heating system typeShare of renewable energy in the building sector (MW installed or GWh generated):on-siteoff-site
Annual operational greenhouse gas emissions (kgCO2eq/(m2.y):per building typeAnnual operational greenhouse gas emission reduction (kgCO2eq/(m2.y):per building typeLife-cycle GWP (kgCO2eq/m2) in new buildings:per building type
Market barriers and failures (description):split incentivescapacity of construction and energy sectorEvaluation of the capacities in the construction, energy efficiency and renewable energy sectorsMarket barriers and failures (description):administrativefinancialtechnicalawarenessotherNumber of:energy service companiesconstruction companiesarchitects and engineersskilled workersone-stop shopsSMEs in the construction/renovation sectorrenewable energy communities and citizen-led renovation initiativesProjections of the construction workforce:retiring architects/engineers/skilled workersarchitects/engineers/skilled workers entering the marketyoung people in the sectorwomen in the sectorOverview and forecast of the evolution of prices of construction materials and national market developments
Energy poverty (definition):% of people affected by energy povertyproportion of disposable household income spent on energypopulation living in inadequate dwelling conditions (e.g. leaking roof) or with inadequate thermal comfort conditions
Primary energy factors:per energy carriernon-renewable primary energy factorrenewable primary energy factortotal primary energy factor
Definition of nearly-zero energy building for new and existing buildingsOverview of the legal and administrative framework
Cost-optimal minimum energy performance requirements for new and existing buildings
(b)Roadmap for 2030, 2040, 2050Targets for annual renovation rates: number and total floor area (m2):per building typeworst-performing buildingsthe 43 % worst-performing residential buildingsInformation pursuant to Article 9(1):criteria to exempt individual non-residential buildingsestimated share of exempted non-residential buildingsestimation of equivalent energy performance improvements due to exempted non-residential buildingsTargets for expected share (%) of renovated buildings:per building typeper renovation depth
Targets for expected primary and final annual energy consumption (ktoe):per building typeper end useExpected energy savings:per building typeTargets for the increase in the share of renewable energy in accordance with Article 15a of Directive (EU) 2018/2001Numerical targets for the deployment of solar energy in buildingsShare of energy from renewable sources in the building sector (MW installed or GWh generated)
Targets for expected operational greenhouse gas emissions (kgCO2eq/(m2.y):per building typeTargets for expected operational greenhouse gas emission reduction (%):per building typeSplit between emissions covered by Chapter III [stationary installations], Chapter IVa [emissions trading system for buildings, road transport and additional sectors] of Directive 2003/87/EC, and other stock;Targets for expected whole-life-cycle greenhouse gas emission (kgCO2eq/(m2.y) in new buildings:per building type
Expected wider benefits:% reduction of people affected by energy povertyCreation of new jobsIncrease in GDP (share and billion euros)
The Member State’s contribution to the Union’s energy efficiency targets in accordance with Article 4 of Directive (EU) 2023/1791 attributable to its building stock’s renovation (share and figure in ktoe)
The Member State’s contribution to the Union’s renewable energy targets in accordance with Directive (EU) 2018/2001 attributable to its building stock’s renovation (share, MW installed or GWh generated)
(c)Overview of implemented and planned policies and measuresPolicies and measures with regard to the following elements:(a)the identification of cost-effective approaches to renovation for different building types and climatic zones, considering potential relevant trigger points in the life cycle of the building;(b)national minimum energy performance standards pursuant to Article 9 and other policies and actions to target the worst-performing segments of the national building stock, including safeguards as referred to in Article 17(19);(c)the promotion of deep renovation of buildings, including staged deep renovation;(d)empowering and protecting vulnerable customers and the alleviation of energy poverty, including policies and measures pursuant to Article 24 of Directive (EU) 2023/1791, and housing affordability;(e)the creation of one-stop shops or similar mechanisms pursuant to Article 18 for the provision of technical, administrative and financial advice and assistance;(f)the decarbonisation of heating and cooling, including through district heating and cooling networks, and the phasing out of fossil fuels in heating and cooling with a view to a complete phasing out of fossil fuel boilers by 2040;(g)prevention and high-quality treatment of construction and demolition waste in accordance with Directive 2008/98/EC, in particular as regards the waste hierarchy, and the objectives of the circular economy;(h)the promotion of renewable energy sources in buildings in line with the indicative target for the share of energy from renewable sources in the building sector laid down in Article 15a(1) of Directive (EU) 2018/2001;(i)the deployment of solar energy installations on buildings;(j)the reduction of whole-life-cycle greenhouse gas emissions for the construction, renovation, operation and end of life of buildings, and the uptake of carbon removals;(k)the promotion of district and neighbourhood approaches and integrated renovation programmes at district level, which may address issues such as energy, mobility, green infrastructure, waste and water treatment and other aspects of urban planning and may take into account local and regional resources, circularity and sufficiency;(l)the improvement of buildings owned by public bodies, including policies and measures pursuant to Articles 5, 6 and 7 of Directive (EU) 2023/1791;(m)the promotion of smart technologies and infrastructure for sustainable mobility in buildings;(n)addressing market barriers and market failures;(o)addressing skills gaps and promoting education, targeted training, upskilling and reskilling in the construction sector and energy efficiency and renewable energy sectors (whether public or private), with a view to ensuring that there is a sufficient workforce with the appropriate level of skills corresponding to the needs in the building sector, with a special focus on the underrepresented groups;(p)awareness-raising campaigns and other advisory tools; and(q)promotion of modular and industrialised solutions for construction and building renovation.For all policies and measures:name of policy or measureshort description (precise scope, objective and conditions of operation)quantified objectivetype of policy or measure (such as legislative; economic; fiscal; training, awareness)planned budget and funding sourcesentities responsible for implementing the policyexpected impactstatus of implementationdate of entry into forceimplementation periodPolicies and measures with regard to the following elements:(a)the increase in the climate resilience of buildings;(b)the promotion of the energy services market;(c)the increase in fire safety;(d)the increase in resilience against disaster risks, including risks related to intense seismic activity;(e)the removal of hazardous substances including asbestos;(f)accessibility for persons with disabilities;(g)the role of renewable energy communities and citizen energy communities in district and neighbourhood approaches;(h)addressing mismatches in human capacities; and(i)addressing the improvement of indoor environmental quality.For all policies and measures:administrative resources and capacitiesarea(s) coveredworst-performingminimum energy performance standardsenergy poverty, social housingpublic buildingsresidential (single-family, multi-family)non-residentialindustryrenewable energy sourcesphasing out of fossil fuels in heating and coolingwhole-lifecycle greenhouse gas emissionscircular economy and wasteone-stop shopsrenovation passportssmart technologiessustainable mobility in buildingsdistrict and neighbourhood approachesskills, trainingawareness campaigns and advisory tools
(d)Outline of the investment needs, the budgetary sources and the administrative resourcestotal investment needs for 2030, 2040, 2050 (million EUR)public investments (million EUR)private investments (million EUR)budgetary resources
(e)Thresholds of new and renovated zero-emission buildings, referred to in Article 11operational greenhouse gas emissions thresholds of new zero-emission buildings;operational greenhouse gas emissions thresholds of renovated zero-emission buildings;annual primary energy use thresholds of new zero-emission buildings;annual primary energy use thresholds of renovated zero-emission buildings
(f)Minimum energy performance standards for non-residential buildingsmaximum energy performance thresholds, pursuant to Article 9(1)
(g)National trajectory for the progressive renovation of the residential building stockthe national trajectory for the progressive renovation of the residential building stock, including the 2030 and 2035 milestones for average primary energy use in kWh/(m2.y), pursuant to Article 9(2)
ANNEX IIICalculation of life-cycle GWP of new buildings pursuant to Article 7(2)For the calculation of the life-cycle GWP of new buildings pursuant to Article 7(2), the total life-cycle GWP is communicated as a numeric indicator for each life-cycle stage expressed as kgCO2eq/(m2) (of useful floor area) calculated over a reference study period of 50 years. The data selection, scenario definition and calculations shall be carried out in accordance with EN 15978 (EN 15978:2011 Sustainability of construction works. Assessment of environmental performance of buildings. Calculation method) and taking into account any subsequent standard relating to the sustainability of construction works and the calculation method for the assessment of environmental performance of buildings. The scope of building elements and technical equipment is as defined in the Level(s) common EU framework for indicator 1.2. Where a national calculation tool or method exists, or is required for making disclosures or for obtaining building permits, that tool or method may be used to provide the required disclosure. Other calculation tools or methods may be used if they fulfil the minimum criteria established by the Level(s) common EU framework. Data regarding specific construction products calculated in accordance with Regulation (EU) No 305/2011 of the European Parliament and of the CouncilRegulation (EU) No 305/2011 of the European Parliament and of the Council of 9 March 2011 laying down harmonised conditions for the marketing of construction products and repealing Council Directive 89/106/EEC (OJ L 88, 4.4.2011, p. 5). shall be used when available.ANNEX IVCommon general framework for rating the smart readiness of buildings1.The Commission shall establish the definition of the smart readiness indicator and a methodology by which it is to be calculated, in order to assess the capabilities of a building or building unit to adapt its operation to the needs of the occupant and of the grid and to improve its energy efficiency and overall performance.The smart readiness indicator shall cover features for enhanced energy savings, benchmarking and flexibility, enhanced functionalities and capabilities resulting from more interconnected and intelligent devices.The methodology shall take into account features such as the possible existence of a digital twin of the building.The methodology shall take into account features such as smart meters, building automation and control systems, self-regulating devices for the regulation of indoor air temperature, built-in home appliances, recharging points for electric vehicles, energy storage and detailed functionalities and the interoperability of those features, as well as benefits for the indoor climate conditions, energy efficiency, performance levels and enabled flexibility.2.The methodology shall rely on the following key functionalities relating to the building and its technical building systems:(a)the ability to maintain energy performance and operation of the building through the adaptation of energy consumption for example through use of energy from renewable sources;(b)the ability to adapt its operation mode in response to the needs of the occupant while paying due attention to the availability of user-friendliness, maintaining healthy indoor climate conditions and the ability to report on energy use;(c)the flexibility of a building’s overall energy demand, including its ability to enable participation in active and passive as well as implicit and explicit demand response, through its energy storage and release of energy back to the grid, for example through flexibility and load shifting capacities; and(d)the ability to improve its energy efficiency and overall performance through the use of energy-saving technologies.3.The methodology may further take into account:(a)the interoperability between systems (smart meters, building automation and control systems, built-in home appliances, self-regulating devices for the regulation of indoor air temperature within the building and indoor air quality sensors and ventilations); and(b)the positive influence of existing communication networks, in particular the existence of high-speed-ready in-building physical infrastructure, such as the voluntary "broadband ready" label, and the existence of an access point for buildings with multiple residential building units, in accordance with Article 8 of Directive 2014/61/EU of the European Parliament and of the CouncilDirective 2014/61/EU of the European Parliament and of the Council of 15 May 2014 on measures to reduce the cost of deploying high-speed electronic communications networks (OJ L 155, 23.5.2014, p. 1)..4.The methodology shall not negatively affect existing national energy performance certification schemes and shall build on related initiatives at national level, while taking into account the principle of occupant ownership, data protection, privacy and security, in compliance with relevant Union data protection and privacy law as well as best available techniques for cyber security.5.The methodology shall set out the most appropriate format of the smart readiness indicator parameter and shall be simple, transparent, and easily understandable for consumers, owners, investors and demand-response market participants.ANNEX VTemplate for energy performance certificates(referred to in Article 19)1.On its front page, the energy performance certificate shall display at least the following elements:(a)the energy performance class;(b)the calculated annual primary energy use in kWh/(m2.y);(c)the calculated annual final energy use in kWh/(m2.y);(d)renewable energy produced on-site in % of energy use;(e)operational greenhouse gas emissions (kgCO2/(m2.y)), and the value of the life-cycle GWP, if available.The energy performance certificate shall also display the following elements:(a)the calculated annual primary and final energy consumption in kWh or MWh;(b)renewable energy production in kWh or MWh; main energy carrier and type of renewable energy source;(c)the calculated energy needs in kWh/(m2.y);(d)a yes/no indication whether the building has a capacity to react to external signals and adjust the energy consumption;(e)a yes/no indication whether the heat distribution system inside the building is capable to work at low or more efficient temperature levels, where applicable;(f)the contact information of the relevant one-stop shop for renovation advice.2.In addition, the energy performance certificate may include the following indicators:(a)energy use, peak load, size of generator or system, main energy carrier and main type of element for each of the uses: heating, cooling, domestic hot water, ventilation and in-built lighting;(b)the greenhouse gas emission class (if applicable);(c)information on carbon removals associated to the temporary storage of carbon in or on buildings;(d)a yes/no indication whether a renovation passport is available for the building;(e)the average U-value for the opaque elements of the building envelope;(f)the average U-value for the transparent elements of the building envelope;(g)type of most common transparent element (e.g. double-glazed window);(h)results of the analysis on overheating risk (if available);(i)the presence of fixed sensors that monitor the indoor environmental quality;(j)the presence of fixed controls that respond to the levels of indoor environmental quality;(k)number and type of recharging points for electric vehicles;(l)presence, type and size of energy storage systems;(m)expected remaining lifespan of the heating or air-conditioning systems and appliances, where applicable;(n)feasibility of adapting the heating system to operate at more efficient temperature settings;(o)feasibility of adapting the domestic hot-water system to operate at more efficient temperature settings;(p)feasibility of adapting the air-conditioning system to operate at more efficient temperature settings;(q)metered energy consumption;(r)whether there is a connection to a district heating and cooling network, and, if available, information about a potential connection to an efficient district heating and cooling system;(s)local primary energy factors and related carbon emission factors of the connected local district heating and cooling network;(t)operational fine particulate matter (PM2,5) emissions.The energy performance certificate may include the following links with other initiatives if these apply in the relevant Member State:(a)a yes/no indication whether a smart readiness assessment has been carried out for the building;(b)where available, the value of the smart readiness assessment;(c)a yes/no indication whether a Digital Building Logbook is available for the building.Persons with disabilities shall have equal access to the information in energy performance certificates.ANNEX VIIndependent control systems for energy performance certificates1.Definition of a valid energy performance certificateMember States shall provide a clear definition of what is considered to be a valid energy performance certificate.The definition of a valid energy performance certificate shall ensure:(a)a validity check of the input data (including on-site checks) of the building used to issue the energy performance certificate and the results stated in the certificate;(b)the validity of the calculations;(c)a maximum deviation for the energy performance of a building, preferably expressed by the numeric indicator of primary energy use (kWh/(m2.y));(d)a minimum number of elements differing from default or standard values.Member States may include additional elements in the definition of a valid energy performance certificate, such as maximum deviation for specific input data values.2.Quality of the independent control system for energy performance certificatesMember States shall provide a clear definition of the quality objectives and the level of statistical confidence that the energy performance certificate framework should achieve. The independent control system shall ensure at least 90 % of valid issued energy performance certificates with a statistical confidence of 95 % for the evaluated period, which shall not exceed one year.The level of quality and the level of confidence of the independent control system for energy performance certificates shall be measured using random sampling and shall account for all elements provided in the definition of a valid energy performance certificate. Member States shall require third-party verification for the evaluation of at least 25 % of the random sample when the independent control systems have been delegated to non-governmental bodies.The validity of the input data shall be verified with information provided by the independent expert. Such information may include product certificates, specifications or building plans that include details on the performance of the different elements included in the energy performance certificate.The validity of the input data shall be verified by on-site visits, which may be carried out by virtual means, where appropriate in at least 10 % of the energy performance certificates that are part of the random sampling used to assess the overall quality of the scheme.In addition to the minimum random sampling to determine the overall level of quality, Member States may use different strategies to specifically detect and target poor quality in energy performance certificates with the objective to improve the overall quality of the scheme. Such targeted analysis cannot be used as the basis to measure the overall quality of the scheme.Member States shall deploy pre-emptive and reactive measures to ensure the quality of the overall energy performance certificate framework. Those measures may include additional training for independent experts, targeted sampling, obligation to re-submit energy performance certificates, proportional fines and temporary or permanent bans for experts.Where information is added to a database it shall be possible for national authorities to identify the originator of the addition, for monitoring and verification purposes.3.Availability of energy performance certificatesThe independent control system shall verify the availability of energy performance certificates to prospective buyers and tenants in order to ensure that it is possible to consider the energy performance of the building in their decision to buy or rent.The independent control system shall verify the visibility of the energy performance indicator and class in advertising media.4.Treatment of building typologiesThe independent control system shall account for different building typologies, particularly for building typologies that are most prevalent in the real estate market, such as single residential, multi-residential, offices or retail.5.Public disclosureMember States shall regularly publish, on the national database on energy performance certificates, at least the following information on the quality system:(a)the definition of a valid energy performance certificate;(b)quality objectives for the energy performance certificate scheme;(c)results of the quality assessment, including number of certificates evaluated and relative size to the total number of issued certificates in the given period (per typology);(d)contingency measures to improve the overall quality of energy performance certificates.ANNEX VIIComparative methodology framework to identify cost-optimal levels of energy performance requirements for buildings and building elementsThe comparative methodology framework shall enable Member States to determine the energy and emission performance of buildings and building elements and the economic aspects of measures relating to the energy and emission performance, and to link them with a view to identifying the cost-optimal level to achieve the 2030 emission reduction and climate neutrality goals, as well as a zero-emission building stock by 2050 at the latest.The comparative methodology framework shall be accompanied by guidelines outlining how to apply that framework in the calculation of cost-optimal performance levels.The comparative methodology framework shall allow for taking into account use patterns, outdoor climate conditions and their future changes according to best available climate projections, including heat and cold waves, investment costs, building category, maintenance and operating costs (including energy costs and savings), earnings from energy produced, where applicable, environmental and health externalities of energy use, waste management costs, where applicable, and technological developments. It should be based on relevant European standards relating to this Directive.The Commission shall also provide:guidelines to accompany the comparative methodology framework; those guidelines will serve to enable the Member States to undertake the steps listed below,information on estimated long-term energy price developments.For the application of the comparative methodology framework by Member States, general conditions, expressed by parameters, shall be laid down at Member State level. The Commission shall issue recommendations to Member States regarding their cost optimality levels, where relevant.The comparative methodology framework shall require Member States to:define reference buildings that are characterised by and representative of their functionality and geographic location, including indoor and outdoor climate conditions. The reference buildings shall cover residential and non-residential buildings, both new and existing ones,define energy efficiency measures to be assessed for the reference buildings. Those may be measures for individual buildings as a whole, for individual building elements, or for a combination of building elements,assess the final and primary energy need and resulting emissions of the reference buildings with the defined energy efficiency measures applied,calculate the costs (i.e. the net present value) of the energy efficiency measures (as referred to in the second indent) during the expected economic life cycle applied to the reference buildings (as referred to in the first indent) by applying the comparative methodology framework principles.By calculating the costs of the energy efficiency measures during the expected economic life cycle, the cost-effectiveness of different levels of minimum energy performance requirements is assessed by the Member States. That will allow the determination of cost-optimal levels of energy performance requirements.ANNEX VIIIRequirements for renovation passports1.The renovation passport shall include:(a)information on the current energy performance of the building;(b)a graphical representation or graphical representations of the roadmap and its steps for a staged deep renovation;(c)information on relevant national requirements such as minimum energy performance requirements for buildings, minimum energy performance standards and rules in the Member State on the phasing out of fossil-fuel used in buildings for heating and cooling, including application dates;(d)a succinct explanation on the optimal sequencing of steps;(e)information about each step, including:(i)the name and description of the renovation measures for the step, including relevant options for the technologies, techniques and materials to be used;(ii)the estimated energy savings in primary and final energy consumption, in kWh and in percentage improvement compared to the energy consumption prior to the step;(iii)the estimated reduction of operational greenhouse gas emissions;(iv)the estimated savings on the energy bill, clearly indicating the assumptions on energy costs used for the calculation;(v)the estimated energy performance class of the energy performance certificate to be achieved following completion of the step;(f)information about a potential connection to an efficient district heating and cooling system;(g)the share of individual or collective generation and self-consumption of renewable energy estimated to be achieved after the renovation;(h)general information on available options for improving construction products’ circularity and for reducing their whole-life-cycle greenhouse gas emissions, as well as wider benefits related to health and comfort, indoor environmental quality and the improved adaptive capacity of the building to climate change;(i)information on available funding and links to the relevant web pages indicating the sources of such funding;(j)information on technical advice and advisory services, including contact details and links to the web pages of one-stop shops.2.The renovation passport may include:(a)an indicative timing of the steps;(b)for each step:(i)a detailed description of the technologies, techniques and materials to be used, their advantages, disadvantages and costs;(ii)how the energy performance of the building would compare to minimum energy performance requirements for buildings undergoing major renovation, nearly zero-energy building and zero-emission building requirements after completion of the step and how the energy performance of the building elements replaced would compare to minimum energy performance requirements for single building elements, where these exist;(iii)the estimated costs for carrying out the step;(iv)the estimated payback period for the step, with and without any available financial support;(v)the estimated time needed to carry out the step;(vi)where available, the reference values on the life-cycle greenhouse gas emissions for the materials and equipment and links to the relevant web pages where they can be found;(vii)the estimated lifetime of measures and the estimated maintenance costs;(c)independent modules on:(i)the typical trades necessary or recommended for carrying out energy renovations (architects, advisors, contractors, suppliers and installer, etc.) or links to the relevant web pages;(ii)a list of relevant architects, advisors, contractors, suppliers or installers in the area, that may include only those fulfilling certain conditions such as matching higher qualification or certification labels or conditions, or links to the relevant web pages;(iii)the technical conditions needed for an optimal roll-out of low temperature heating;(iv)how the renovation steps and additional measures could improve the smart readiness of a building;(v)technical and safety requirements for materials and works;(vi)the underlying assumptions behind the calculations provided or links to the relevant web page where they can be found;(d)information on how to access a digital version of the renovation passport;(e)any major renovations made to the building or building unit, as referred to in Article 8(1), and any retrofitting or replacement of a building element that forms part of the building envelope and which has a significant impact on the energy performance of the building envelope, as referred to in Article 8(2), where such information is made available to the expert carrying out the renovation passport;(f)information related to seismic safety, where such information relevant to the building is made available to the expert;(g)upon request of and on the basis of information made available by the current building owner, an attachment containing additional information, such as the adaptability of spaces to evolving needs and any planned renovations.3.Regarding the status of the building prior to the renovation steps, the renovation passport shall consider, to the extent possible, information contained in the energy performance certificate.4.Each metric used for estimating the impact of steps shall be based on a set of standard conditions.ANNEX IXPART ARepealed Directive with list of the successive amendments thereto(referred to in Article 36)
Directive 2010/31/EU of the European Parliament and of the Council(OJ L 153, 18.6.2010, p. 13).
Directive (EU) 2018/844 of the European Parliament and of the Council(OJ L 156, 19.6.2018, p. 75).only Article 1
Regulation (EU) 2018/1999 of the European Parliament and of the Council(OJ L 328, 21.12.2018, p. 1).only Article 53
PART BTime-limits for transposition into national law and dates of application(referred to in Article 36)
DirectiveTime-limit for transpositionDates of application
2010/31/EU9 July 2012as far as Articles 2, 3, 9, 11, 12, 13, 17, 18, 20 and 27 are concerned, 9 January 2013;as far as Articles 4 to 8, 14, 15 and 16 are concerned, 9 January 2013 with regard to buildings occupied by the public authorities and 9 July 2013 with regard to other buildings
(EU)2018/84410 March 2020
ANNEX XCorrelation table
Directive 2010/31/EUThis Directive
Article 1Article 1
Article 2, point (1)Article 2, point 1
—Article 2, point (2)
Article 2, point (2)Article 2, point (3)
—Article 2, points (5) and (6)
Article 2, points (3), (3a), (4) and (5)Article 2, points (7) to (10)
—Article 2, points (12), (13) and (14)
Article 2, points (6), (7), (8) and (9)Article 2, points (15) to (18)
—Article 2, points (19) to (22)
Article 2, point (10)Article 2, point (23)
—Article 2, points (24) to (29)
Article 2, points (11), (12), (13) and (14)Article 2, points (30) to (33)
—Article 2, points (34), (37) to (40) and (42)
Article 2, point (15)Article 2, point (42)
Article 2, points (15), (15a), (15b), (15c), (16) and (17)Article 2, points (43), (44), (47) to (50)
Article 2, point (18)—
Article 2, point (19)Article 2, point (51)
—Article 2, points (52) to (64)
Article 2, point (20)—
Article 2aArticle 3
Article 3Article 4
Article 4Article 5
Article 5Article 6
Articles 6 and 9Article 7
Article 7Article 8
—Article 9
—Article 12
Article 8(1), (9)Article 13
Article 8(2) to (8)Article 14
Article 8(10), (11)Article 15
—Article 16
Article 10Article 17
Article 11Article 19
Article 12Article 20
Article 13Article 21
—Article 22
Articles 14 and 15Article 23
Article 16Article 24
Article 17Article 25
—Article 26
Article 18Article 27
Article 19Article 28
Article 19a—
Article 20Article 29
Article 21Article 30
Article 22Article 31
Article 23Article 32
Article 26Article 33
Article 27Article 34
Article 28Article 35
Article 29Article 36
Article 30Article 37
Article 31Article 38
Annex IAnnex I
—Annex II
—Annex III
Annex IAAnnex IV
—Annex V
Annex IIAnnex VI
Annex IIIAnnex VII
Annex IVAnnex IX
Annex VAnnex X