Regulation (EC) No 661/2009 of the European Parliament and of the Council of 13 July 2009 concerning type-approval requirements for the general safety of motor vehicles, their trailers and systems, components and separate technical units intended therefor (Text with EEA relevance)
Modified by
  • Commission Regulation (EU) No 407/2011of 27 April 2011amending Regulation (EC) No 661/2009 of the European Parliament and of the Council as regards the inclusion of certain Regulations of the United Nations Economic Commission for Europe on the type-approval of motor vehicles, their trailers and systems, components and separate technical units intended therefor(Text with EEA relevance), 32011R0407, April 28, 2011
  • Commission Regulation (EU) No 523/2012of 20 June 2012amending Regulation (EC) No 661/2009 of the European Parliament and of the Council as regards the inclusion of certain Regulations of the United Nations Economic Commission for Europe on the type-approval of motor vehicles, their trailers and systems, components and separate technical units intended therefor(Text with EEA relevance), 32012R0523, June 21, 2012
  • Commission Regulation (EU) 2015/166of 3 February 2015supplementing and amending Regulation (EC) No 661/2009 of the European Parliament and of the Council as regards the inclusion of specific procedures, assessment methods and technical requirements, and amending Directive 2007/46/EC of the European Parliament and of the Council, and Commission Regulations (EU) No 1003/2010, (EU) No 109/2011 and (EU) No 458/2011(Text with EEA relevance), 32015R0166, February 4, 2015
  • Commission Regulation (EU) 2016/1004of 22 June 2016amending Regulation (EC) No 661/2009 of the European Parliament and of the Council(Text with EEA relevance), 32016R1004, June 23, 2016
  • Commission Regulation (EU) 2019/543of 3 April 2019amending Annex IV to Regulation (EC) No 661/2009 of the European Parliament and of the Council and Annexes I, III and IV to Directive 2007/46/EC of the European Parliament and of the Council as regards updating the references to and including certain Regulations of the United Nations Economic Commission for Europe on the type-approval of motor vehicles(Text with EEA relevance), 32019R0543, April 4, 2019
  • Regulation (EU) 2019/2144 of the European Parliament and of the Councilof 27 November 2019on type-approval requirements for motor vehicles and their trailers, and systems, components and separate technical units intended for such vehicles, as regards their general safety and the protection of vehicle occupants and vulnerable road users, amending Regulation (EU) 2018/858 of the European Parliament and of the Council and repealing Regulations (EC) No 78/2009, (EC) No 79/2009 and (EC) No 661/2009 of the European Parliament and of the Council and Commission Regulations (EC) No 631/2009, (EU) No 406/2010, (EU) No 672/2010, (EU) No 1003/2010, (EU) No 1005/2010, (EU) No 1008/2010, (EU) No 1009/2010, (EU) No 19/2011, (EU) No 109/2011, (EU) No 458/2011, (EU) No 65/2012, (EU) No 130/2012, (EU) No 347/2012, (EU) No 351/2012, (EU) No 1230/2012 and (EU) 2015/166(Text with EEA relevance), 32019R2144, December 16, 2019
Corrected by
  • Corrigendum to Regulation (EC) No 661/2009 of the European Parliament and of the Council of 13 July 2009 concerning type-approval requirements for the general safety of motor vehicles, their trailers and systems, components and separate technical units intended therefor, 32009R0661R(01), December 20, 2011
  • Corrigendum to Regulation (EC) No 661/2009 of the European Parliament and of the Council of 13 July 2009 concerning type-approval requirements for the general safety of motor vehicles, their trailers and systems, components and separate technical units intended therefor, 32009R0661R(05), November 25, 2015
Regulation (EC) No 661/2009 of the European Parliament and of the Councilof 13 July 2009concerning type-approval requirements for the general safety of motor vehicles, their trailers and systems, components and separate technical units intended therefor(Text with EEA relevance) CHAPTER ISUBJECT MATTER, SCOPE AND DEFINITIONS
Article 1Subject matterThis Regulation establishes requirements:1.for the type-approval of motor vehicles, their trailers and systems, components and separate technical units intended therefor with regard to their safety,2.for the type-approval of motor vehicles, in respect of tyre pressure monitoring systems, with regard to their safety, fuel efficiency and CO2 emissions and, in respect of gear shift indicators, with regard to their fuel efficiency and CO2 emissions; and3.for the type-approval of newly-manufactured tyres with regard to their safety, rolling resistance performance and rolling noise emissions.
Article 2ScopeThis Regulation shall apply to vehicles of categories M, N and O and systems, components and separate technical units intended therefor as defined in Section A of Annex II to Directive 2007/46/EC, subject to Articles 5 to 12 of this Regulation.
Article 3DefinitionsFor the purposes of this Regulation, the definitions laid down in Article 3 of Directive 2007/46/EC shall apply.In addition, the following definitions shall apply:1."electronic stability control" means an electronic control function for a vehicle which improves the dynamic stability of the vehicle;2."class I M2 or M3 vehicle" means an M2 or M3 vehicle with a capacity exceeding 22 passengers in addition to the driver constructed with areas for standing passengers to allow frequent passenger movement;3."class A M2 or M3 vehicle" means an M2 or M3 vehicle with a capacity not exceeding 22 passengers, in addition to the driver, designed to carry standing passengers and having seats and provision for standing passengers;4."lane departure warning system" means a system to warn the driver of unintentional drift of the vehicle out of its travel lane;5."advanced emergency braking system" means a system which can automatically detect an emergency situation and activate the vehicle braking system to decelerate the vehicle with the purpose of avoiding or mitigating a collision;6."load-capacity index" means one or two numbers which indicate the load the tyre can carry in single or in single and dual formation at the speed corresponding to the associated speed category and when used in conformity with requirements specified by the manufacturer;7."tyre pressure monitoring system" means a system fitted on a vehicle which can evaluate the pressure of the tyres or the variation of pressure over time and transmit corresponding information to the user while the vehicle is running;8."special use tyre" means a tyre intended for mixed use both on- and off-road or for other special duty;9."off-road professional tyre" means a special use tyre primarily used in severe off-road conditions;10."reinforced tyre" or "extra load tyre" means a C1 pneumatic tyre structure in which the carcass is designed to carry a greater load than the corresponding standard tyre;11."snow tyre" means a tyre whose tread pattern, tread compound or structure is primarily designed to achieve in snow conditions a performance better than that of a normal tyre with regard to its ability to initiate or maintain vehicle motion;12."T-type temporary-use spare tyre" means a temporary-use spare tyre designed for use at inflation pressures higher than those established for standard and reinforced tyres;13."traction tyre" means a tyre of classes C2 or C3 bearing the inscription "M + S", "M.S." or "M&S" and intended to be fitted to a vehicle drive axle or axles;14."unprotected road user" means pedestrians, cyclists and motorcyclists;15."gear shift indicator" or "GSI" means a visible indicator recommending that the driver shift gear;16."manual gearbox" means a gearbox that can be operated in a mode where the shift between all or some of the gears is always an immediate consequence of an action of the driver, regardless of its physical implementation; this does not cover systems where the driver can only preselect a certain gear shift strategy or limit the number of gears available for driving, and where the actual gear shifts are initiated independently of the decision of the driver according to certain driving patterns.

CHAPTER IIOBLIGATIONS OF MANUFACTURERS
Article 4General obligations1.Manufacturers shall demonstrate that all new vehicles sold, registered or put into service within the Community are type-approved in accordance with this Regulation and its implementing measures.2.Manufacturers may choose to apply for type-approval with regard to all the systems, and the installation of all the components and separate technical units covered by this Regulation, or for type-approval with regard to one or more systems and the installation of one or more components and one or more separate technical units covered by this Regulation. Type-approval in accordance with the UNECE Regulations listed in Annex IV shall be considered as EC type-approval in accordance with this Regulation and its implementing measures.3.Manufacturers shall demonstrate that all new systems, components and separate technical units sold or put into service within the Community are type-approved in accordance with this Regulation and its implementing measures.
Article 5General requirements and tests1.Manufacturers shall ensure that vehicles are designed, constructed and assembled so as to minimise the risk of injury to vehicle occupants and other road users.2.Manufacturers shall ensure that vehicles, systems, components and separate technical units comply with the relevant requirements set out in this Regulation and its implementing measures, including the requirements relating to:(a)vehicle structure integrity, including impact tests;(b)systems to aid the driver’s control of the vehicle, including steering, braking and electronic stability control systems;(c)systems to provide the driver with visibility and information on the state of the vehicle and the surrounding area, including glazing, mirrors and driver information systems;(d)vehicle lighting systems;(e)vehicle occupant protection, including interior fittings, head restraints, seat belts, "ISOfix" anchorages or built-in child restraints and vehicle doors;(f)the vehicle exterior and accessories;(g)electromagnetic compatibility;(h)audible warning devices;(i)heating systems;(j)devices to prevent unauthorised use;(k)vehicle identification systems;(l)masses and dimensions;(m)electrical safety;(n)gear shift indicators.3.The requirements referred to in paragraphs 1 and 2 shall apply to vehicles and systems, components and separate technical units intended therefor, as specified in Annex I.
Article 6Specific requirements relating to certain vehicles of categories N and O1.In addition to the requirements contained in Articles 5, 8, 9, 10 and 12 and the implementing measures thereof, vehicles of categories N and O shall, where relevant, meet the requirements set out in paragraphs 2 to 5 of this Article and the implementing measures thereof.2.Vehicles of categories N2 and N3 shall be constructed to ensure that, in the event of a front collision with another vehicle, the risk of injury to a vehicle occupant due to underrun is minimised.3.Vehicles of categories N2, N3, O3 and O4 shall be constructed to ensure that, in the event of the vehicle being hit from the side by an unprotected road user, the risk of injury to that unprotected road user due to underrun is minimised.4.The vehicle cab or the space provided for the driver and passengers shall be of sufficient strength to offer protection to the occupants in the event of an impact, taking account of UNECE Regulation 29.5.Vehicles of categories N2, N3, O3 and O4 shall be constructed so as to minimise the effect of spray emissions from the vehicle on the ability of drivers of other vehicles to see.
Article 7Specific requirements relating to vehicles of categories M2 and M31.In addition to the requirements contained in Articles 5, 8, 9, 10 and 12 and the implementing measures thereof, vehicles of categories M2 and M3 shall meet the requirements set out in paragraphs 2 to 5 of this Article and the implementing measures thereof.2.The carrying capacity of a vehicle, including seated and standing passengers and wheelchair users, shall be appropriate to the mass, size and layout of the vehicle.3.Vehicle bodies shall be designed and constructed so as to enable the vehicle to be operated in a safe and stable manner, even at full capacity. Suitable provisions shall be made to ensure safe access to and exit from the vehicle, particularly in the case of an emergency.4.Vehicles of Class I shall be accessible for people with reduced mobility, including wheelchair users.5.Materials used in the construction of the inside of bus and coach bodywork shall, as far as possible, prevent or at least retard fire in order to allow occupants to evacuate the vehicle in the event of fire.
Article 8Classification of tyres1.Tyres shall be classified as follows:(a)class C1 tyrestyres designed primarily for vehicles of categories M1, N1, O1 and O2;(b)class C2 tyrestyres designed primarily for vehicles of categories M2, M3, N, O3 and O4 with a load capacity index in single formation ≤ 121 and the speed category symbol ≥ "N";(c)class C3 tyrestyres designed primarily for vehicles of categories M2, M3, N, O3 and O4 with one of the following load capacity indices:(i)a load capacity index in single formation ≤ 121 and the speed category symbol ≤ "M";(ii)a load capacity index in single formation ≥ 122.A tyre may be classified in more than one class provided that it meets all the relevant requirements of each class in which it is classified.2.The list of load-capacity indices and their corresponding masses contained in UNECE Regulations 30 and 54 shall apply.
Article 9Specific provisions relating to vehicle tyres, installation of tyres and tyre pressure monitoring systems1.All tyres provided as part of the equipment of a vehicle, including, where appropriate, any spare tyres, shall be suitable for use on the vehicles for which they are intended, particularly with regard to their dimensions, speed and load performance characteristics.2.Vehicles of category M1 shall be equipped with an accurate tyre pressure monitoring system capable of giving, when necessary, an in-car warning to the driver when a loss of pressure occurs in any tyre, in the interests of optimum fuel consumption and road safety. Appropriate limits in the technical specifications shall be set to achieve this, which shall furthermore allow for a technology-neutral and cost-effective approach in the development of accurate tyre pressure monitoring systems.3.All C1 tyres shall meet the wet grip requirements contained in Part A of Annex II.4.All tyres shall meet the rolling resistance requirements contained in Part B of Annex II.5.All tyres shall meet the rolling noise requirements contained in Part C of Annex II.6.Paragraphs 3, 4 and 5 shall not apply to:(a)tyres whose speed rating is less than 80 km/h;(b)tyres whose nominal rim diameter does not exceed 254 mm or is 635 mm or more;(c)T-type temporary-use spare tyres;(d)tyres designed only to be fitted to vehicles registered for the first time before 1 October 1990;(e)tyres fitted with additional devices to improve traction properties.7.The requirements regarding rolling resistance and rolling noise set out in Parts B and C of Annex II shall not apply to off-road professional tyres.
Article 10Advanced vehicle systems1.Subject to exemptions established in accordance with Article 14(3)(a), vehicles of categories M2, M3, N2 and N3 shall be equipped with an advanced emergency braking system which shall meet the requirements of this Regulation and its implementing measures.2.Subject to exemptions established in accordance with Article 14(3)(a), vehicles of categories M2, M3, N2 and N3 shall be equipped with a lane departure warning system which shall meet the requirements of this Regulation and its implementing measures.
Article 11Gear shift indicatorsVehicles of category M1 with a reference mass not exceeding 2610 kg and vehicles to which type-approval is extended in accordance with Article 2(2) of Regulation (EC) No 715/2007 which are fitted with a manual gearbox shall be equipped with gear shift indicators in accordance with the requirements of this Regulation and its implementing measures.
Article 12Electronic stability control systems1.Vehicles of categories M1 and N1 shall be equipped with an electronic stability control system meeting the requirements of this Regulation and its implementing measures.2.With the exception of off-road vehicles as defined in points 4.2 and 4.3 of Section A of Annex II to Directive 2007/46/EC, the following vehicles shall be equipped with an electronic stability control system meeting the requirements of this Regulation and its implementing measures:(a)vehicles of categories M2 and M3, except for those with more than three axles, articulated buses and coaches, and buses of Class I or Class A;(b)vehicles of categories N2 and N3 except for those with more than three axles, tractors for semi-trailers with a gross vehicle mass between 3.5 and 7.5 tonnes, and special purpose vehicles as defined in points 5.7 and 5.8 of Section A of Annex II to Directive 2007/46/EC;(c)vehicles of categories O3 and O4 equipped with air suspension, except for those with more than three axles, trailers for exceptional load transport and trailers with areas for standing passengers.
CHAPTER IIIOBLIGATIONS OF THE MEMBER STATES
Article 13Type-approval of vehicles, components and separate technical units1.With effect from 1 November 2011, national authorities shall refuse, on grounds relating to electronic stability control systems, to grant EC type-approval or national type-approval in respect of new types of vehicle of categories M1 and N1 which do not comply with this Regulation and its implementing measures.Following the implementation dates set out in Table 1 of Annex V, national authorities shall refuse, on grounds relating to electronic stability control systems, to grant EC type-approval or national type-approval in respect of new types of vehicle of categories M2, M3, N2, N3, O3 and O4, which do not comply with this Regulation and its implementing measures.2.With effect from 1 November 2012, national authorities shall refuse to grant on grounds relating to the areas of vehicle safety and tyres covered by Articles 5 to 8, Article 9(2) and Article 11:(a)EC type-approval or national type-approval in respect of new types of vehicle of the categories specified in those Articles and their implementing measures, where such vehicles do not comply with this Regulation and its implementing measures; and(b)EC component/separate technical unit type-approval in respect of new types of components or separate technical units intended for such vehicles, where such components or separate technical units do not comply with this Regulation and its implementing measures.3.With effect from 1 November 2012, national authorities shall refuse, on grounds relating to the areas of tyres covered by Article 9(1) and (3) to (7) and Annex II, with the exception of the rolling resistance limit values set out in Table 2 of Part B of Annex II, to grant EC component/separate technical unit type-approval in respect of new types of tyre which do not comply with this Regulation and its implementing measures.With effect from 1 November 2013, national authorities shall refuse, on grounds relating to the areas of tyres covered by Article 9(1) and (3) to (7) and Annex II, with the exception of the rolling resistance limit values set out in Table 2 of Part B of Annex II, to grant EC type-approval or national type-approval in respect of new types of vehicle of the categories M, N and O which do not comply with this Regulation and its implementing measures.4.Following the implementation dates set out in Table 2 of Annex V, national authorities shall, on grounds relating to electronic stability control systems, consider certificates of conformity for new vehicles of categories M2, M3, N2, N3, O3 and O4 to be no longer valid for the purposes of Article 26 of Directive 2007/46/EC, and shall prohibit the registration, sale and entry into service of such vehicles, where such vehicles do not comply with this Regulation and its implementing measures.5.With effect from 1 November 2014, national authorities shall, on grounds relating to the areas of vehicle safety and tyres covered by Articles 5, 6, 7 and 8, Article 9(1) to (4), Article 11, Article 12(1) and Parts A and B of Annex II, with the exception of the rolling resistance limit values for C3 tyres and the rolling resistance limit values set out in Table 2 of Part B of Annex II:(a)consider certificates of conformity for new vehicles of the categories specified in those Articles to be no longer valid for the purposes of Article 26 of Directive 2007/46/EC, and prohibit the registration, sale and entry into service of such vehicles, where such vehicles do not comply with this Regulation and its implementing measures; and(b)prohibit the sale and entry into service of new components or separate technical units intended for such vehicles, where such components or separate technical units do not comply with this Regulation and its implementing measures.6.With effect from 1 November 2016, national authorities shall, on grounds relating to tyre rolling noise and, in the case of C3 tyres, also on grounds relating to tyre rolling resistance, with the exception of the rolling resistance limit values set out in Table 2 of Part B of Annex II:(a)consider certificates of conformity for new vehicles of categories M, N and O to be no longer valid for the purposes of Article 26 of Directive 2007/46/EC, and prohibit the registration, sale and entry into service of such vehicles, where such vehicles do not comply with this Regulation and its implementing measures; and(b)prohibit the sale and entry into service of new tyres intended for such vehicles, where such tyres do not comply with this Regulation and its implementing measures.7.With effect from 1 November 2016 national authorities shall refuse, on grounds relating to tyre rolling resistance, to grant EC component/separate technical unit type-approval in respect of new types of tyres which do not comply with the rolling resistance limit values set out in Table 2 of Part B of Annex II.8.With effect from 1 November 2017 national authorities shall refuse, on grounds relating to tyre rolling resistance, to grant EC type-approval or national type-approval in respect of new types of vehicle of categories M, N and O which do not comply with the rolling resistance limit values set out in Table 2 of Part B of Annex II.9.With effect from 1 November 2018 national authorities shall:(a)on grounds relating to the rolling resistance limit values of C1 and C2 tyres set out in Table 2 of Part B of Annex II, consider certificates of conformity for new vehicles of categories M, N and O to be no longer valid for the purposes of Article 26 of Directive 2007/46/EC, and prohibit the registration, sale and entry into service of such vehicles, where such vehicles do not comply with this Regulation and its implementing measures; and(b)prohibit the sale and entry into service of new tyres intended for such vehicles, where such tyres do not comply with the rolling resistance limit values set out in Table 2 of Part B of Annex II.10.With effect from 1 November 2020 national authorities shall:(a)on grounds relating to the rolling resistance limit values of C3 tyres set out in Table 2 of Part B of Annex II, consider certificates of conformity for new vehicles of categories M, N and O to be no longer valid for the purposes of Article 26 of Directive 2007/46/EC, and prohibit the registration, sale and entry into service of such vehicles, where such vehicles do not comply with this Regulation and its implementing measures; and(b)prohibit the sale and entry into service of new tyres intended for such vehicles, where such tyres do not comply with the rolling resistance limit values set out in Table 2 of Part B of Annex II.11.C1, C2 and C3 tyres that were manufactured prior to the dates set out in paragraphs 5, 6, 9 and 10 and which do not comply with the requirements of Annex II may be sold for a period not exceeding 30 months from those dates.12.With effect from 1 November 2013 national authorities shall refuse, on grounds relating to the areas of vehicle safety covered in Article 10, to grant EC type-approval or national type-approval in respect of new types of vehicle of categories M2, M3, N2 and N3, where such vehicles do not comply with this Regulation and its implementing measures.13.With effect from 1 November 2015 national authorities shall, on grounds relating to vehicle safety covered in Article 10, consider certificates of conformity for new vehicles of categories M2, M3, N2 and N3 to be no longer valid for the purposes of Article 26 of Directive 2007/46/EC, and prohibit the registration, sale and entry into service of such vehicles, where such vehicles do not comply with this Regulation and its implementing measures.14.National authorities shall permit the sale and entry into service of vehicles, components and separate technical units type-approved before the dates referred to in paragraphs 1, 2 and 3 and continue to grant extension of approvals to those vehicles, components and separate technical units under the terms of the regulatory act under which they were originally permitted or granted, unless the requirements applying to such vehicles, components or separate technical units have been modified or new requirements have been added by this Regulation and its implementing measures.National authorities shall permit the sale and entry into service of and continue to grant extensions to EC type-approval to replacement components and separate technical units, with the exception of replacement tyres, intended for vehicles type-approved before the dates referred to in paragraphs 1, 2 and 3, under the terms of the regulatory act under which they were originally permitted or granted.15.Without prejudice to paragraphs 1 to 14, and subject to entry into force of the implementing measures referred to in Article 14, if a manufacturer so requests, national authorities may not, on grounds relating to the areas of vehicle safety and tyres covered in Articles 5 to 12:(a)refuse to grant EC type-approval or national type-approval for a new type of vehicle or to grant EC component/separate technical unit type-approval for a new type of component or separate technical unit, where such vehicle, component or separate technical unit complies with this Regulation and its implementing measures; or(b)prohibit the registration, sale or entry into service of a new vehicle or prohibit the sale or entry into service of a new component or separate technical unit, where the vehicle, component or separate technical unit concerned complies with this Regulation and its implementing measures.
CHAPTER IVIMPLEMENTATION
Article 14Implementing measures1.The Commission shall adopt the following implementing measures:(a)detailed rules concerning the specific procedures, tests and technical requirements for the type-approval of motor vehicles, their trailers and components and separate technical units with regard to the provisions of Articles 5 to 12;(b)detailed rules concerning specific safety requirements for vehicles intended for the transport of dangerous goods by road within or between Member States, taking account of UNECE Regulation 105;(c)a more precise definition of the physical characteristics and performance requirements a tyre must fulfil to be defined as "special use tyre", "off-road professional tyre", "reinforced tyre", "extra load tyre", "snow tyre", "T-type temporary-use spare tyre" or "traction tyre" in accordance with points 8 to 13 of the second paragraph of Article 3;(d)measures amending the limit values on rolling resistance and rolling noise laid down in Parts B and C of Annex II insofar as is necessary as a result of changes in test procedures and without lowering the level of protection of the environment;(e)detailed rules on the procedure for the determination of the noise levels referred to in point 1 of Part C of Annex II;(f)measures amending Annex IV to include the UNECE Regulations that are mandatory under Article 4(4) of Decision 97/836/EC.2.The measures referred to in paragraph 1, with the exception of those relating to the provisions of Article 10, shall be adopted by 31 December 2010.The measures relating to the provisions of Article 10 shall be adopted by 31 December 2011.3.The Commission may adopt the following implementing measures:(a)measures exempting certain vehicles or classes of vehicles of categories M2, M3, N2 and N3 from the obligation to install advanced vehicle systems referred to in Article 10 where, following a cost/benefit analysis and taking into account all relevant safety aspects, the application of those systems proves not to be appropriate to the vehicle or class of vehicles concerned;(b)by 31 December 2010, and on the basis of a cost/benefit analysis, measures shortening the period laid down in Article 13(11), which may be differentiated according to the class or category of tyres concerned.4.The measures referred to in this Article, designed to amend non-essential elements of this Regulation, inter alia, by supplementing it, shall be adopted in accordance with the regulatory procedure with scrutiny referred to in Article 15(2).
Article 15Committee procedure1.The Commission shall be assisted by the Technical Committee — Motor Vehicles (TCMV) established by Article 40(1) of Directive 2007/46/EC.2.Where reference is made to this paragraph, Article 5a(1) to (4) and Article 7 of Decision 1999/468/EC shall apply, having regard to the provisions of Article 8 thereof.
CHAPTER VFINAL PROVISIONS
Article 16Penalties for non-compliance1.Member States shall lay down the rules on penalties applicable to infringement by manufacturers of the provisions of this Regulation and its implementing measures and shall take all measures necessary to ensure that they are implemented. The penalties provided for shall be effective, proportionate and dissuasive. By 20 February 2011 or, as appropriate, 18 months from the date of entry into force of the relevant implementing measure, Member States shall notify those provisions to the Commission, and shall notify it without delay of any subsequent amendment affecting them.2.The types of infringement which are subject to a penalty shall include at least the following:(a)making false declarations during an approval procedure or a procedure leading to a recall;(b)falsifying test results for type-approval;(c)withholding data or technical specifications which could lead to recall or withdrawal of type-approval.
Article 17ReportingBy 1 December 2012 and every three years thereafter, the Commission shall present a report to the European Parliament and to the Council including, where appropriate, proposals for amendment to this Regulation or other relevant Community legislation regarding the inclusion of further new safety features.
Article 18Amendments to Directive 2007/46/ECAnnexes IV, VI, XI and XV to Directive 2007/46/EC shall be amended in accordance with Annex III to this Regulation.
Article 19Repeal1.Directives 70/221/EEC, 70/222/EEC, 70/311/EEC, 70/387/EEC, 70/388/EEC, 71/320/EEC, 72/245/EEC, 74/60/EEC, 74/61/EEC, 74/297/EEC, 74/408/EEC, 74/483/EEC, 75/443/EEC, 76/114/EEC, 76/115/EEC, 76/756/EEC, 76/757/EEC, 76/758/EEC, 76/759/EEC, 76/760/EEC, 76/761/EEC, 76/762/EEC, 77/389/EEC, 77/538/EEC, 77/539/EEC, 77/540/EEC, 77/541/EEC, 77/649/EEC, 78/316/EEC, 78/317/EEC, 78/318/EEC, 78/549/EEC, 78/932/EEC, 89/297/EEC, 91/226/EEC, 92/21/EEC, 92/22/EEC, 92/24/EEC, 92/114/EEC, 94/20/EC, 95/28/EC, 96/27/EC, 96/79/EC, 97/27/EC, 98/91/EC, 2000/40/EC, 2001/56/EC, 2001/85/EC, 2003/97/EC shall be repealed with effect from 1 November 2014.2.Directive 92/23/EEC shall be repealed with effect from 1 November 2017.3.References to the repealed Directives shall be construed as references to this Regulation.
Article 20Entry into forceThis Regulation shall enter into force on the 20th day following its publication in the Official Journal of the European Union.It shall apply from 1 November 2011.Article 13(15), Article 14 and points 1(a)(iii), 1(b)(iii) and (iv), 2(c), 3(a)(iii), 3(b)(iii), 3(c)(iii), 3(d)(iii), 3(e)(iii) and 3(f)(ii) of Annex III shall apply from 20 August 2009.Points 1(a)(i), 1(b)(i), 2(a), 3(a)(i), 3(b)(i), 3(c)(i), 3(d)(i), 3(e)(i) and 3(f)(i) of Annex III shall apply from 1 November 2014.Points 1(a)(ii), 1(b)(ii), 2(b), 3(a)(ii), 3(b)(ii), 3(c)(ii), 3(d)(ii), 3(e)(ii) and point 4 of Annex III shall apply from 1 November 2017.
This Regulation shall be binding in its entirety and directly applicable in all Member States.ANNEX IScope of application of the requirements referred to in Article 5(1) and (2)
Vehicles of this category shall be fitted with an adequate windscreen defrosting and demisting device.Vehicles of this category shall be fitted with adequate windscreen washing and wiping devices.Only if the vehicle is fitted with couplings.Not exceeding 2,5 tonnes technically permissible maximum laden mass.Only applicable to vehicles where the "Seating reference point ("R" point)" of the lowest seat is not more than 700 mm above ground level. The "R" point is defined in UNECE Regulation 95.Only when the manufacturer applies for type-approval of a vehicle intended for the transport of dangerous goods.
SubjectApplicability
M1M2M3N1N2N3O1O2O3O4
Fuel tanks/rear protective devicesXXXXXXXXXX
Rear registration plateXXXXXXXXXX
Steering effortXXXXXXXXXX
Door latches and hingesXXXX
Audible warningXXXXXX
Indirect vision devicesXXXXXX
BrakingXXXXXXXXXX
Radio interference (electromagnetic compatibility)XXXXXXXXXX
Interior fittingsX
Anti-theft and immobiliserXXXXXX
Protective steeringXX
Seat strengthXXXXXX
Exterior projectionsX
SpeedometerXXXXXX
Plates (statutory)XXXXXXXXXX
Seat belt anchoragesXXXXXX
Installation of lighting and light signalling devicesXXXXXXXXXX
Retro reflectorsXXXXXXXXXX
End-outline, front-position (side), rear-position (side), stop, side marker, daytime running lampsXXXXXXXXXX
Direction indicatorsXXXXXXXXXX
Rear registration plate lampsXXXXXXXXXX
Headlamps (including bulbs)XXXXXX
Front fog lampsXXXXXX
Towing hooksXXXXXX
Rear fog lampsXXXXXXXXXX
Reversing lampsXXXXXXXXXX
Parking lampsXXXXXX
Seat belts and restraint systemsXXXXXX
Forward visionX
Identification of controls, tell-tales and indicatorsXXXXXX
Defrost/demistX
Wash/wipeX
Heating systemsXXXXXXXXXX
Wheel guardsX
Head restraintsX
Lateral protectionXXXX
Spray-suppression systemsXXXXXXX
Safety glazingXXXXXXXXXX
TyresXXXXXXXXXX
Speed limitation devicesXXXX
Masses and dimensionsXXXXXXXXXX
External projections of cabsXXX
CouplingsXXXXXXXXXX
FlammabilityX
Buses and coachesXX
Frontal impactX
Side impactXX
Vehicles intended for the transportation of dangerous goodsXXXXXXX
Front underrun protectionXX
Electric safetyXXXXXX
ANNEX IIRequirements for tyres with regard to wet grip, rolling resistance and rolling noisePART A —WET GRIP REQUIREMENTSClass C1 tyres shall meet the following requirements:
Category of useWet grip index (G)
snow tyre with a speed symbol ("Q" or below, excluding "H") indicating a maximum permissible speed not greater than 160 km/h≥ 0,9
snow tyre with a speed symbol ("R" and above, including "H") indicating a maximum permissible speed greater than 160 km/h≥ 1,0
normal (road type) tyre≥ 1,1
PART B —ROLLING RESISTANCE REQUIREMENTSThe maximum values for the rolling resistance coefficient for each tyre type, measured in accordance with ISO 28580, shall not exceed the following:
Table 1
Tyre classMax value (kg/tonne)1st stage
C112,0
C210,5
C38,0
Table 2
Tyre classMax value (kg/tonne)2nd stage
C110,5
C29,0
C36,5
For snow tyres, the limits in Table 1 and Table 2 shall be increased by 1 kg/tonne.
PART C —ROLLING NOISE REQUIREMENTS1.The noise levels determined in accordance with the procedure specified in the implementing measures to this Regulation shall not exceed the limits designated in points 1.1 or 1.2. The Tables in points 1.1 and 1.2 represent the measured values corrected for temperature, except in the case of C3 tyres, and instrument tolerance, and are rounded down to the nearest whole value.1.1.Class C1 tyres, with reference to the nominal section width of the tyre that has been tested:
Tyre classNominal section width (mm)Limit values in dB(A)
C1A≤ 18570
C1B> 185 ≤ 21571
C1C> 215 ≤ 24571
C1D> 245 ≤ 27572
C1E> 27574
For snow tyres, extra load tyres or reinforced tyres, or any combination of these classifications, the above limits shall be increased by 1 dB(A).
1.2.Class C2 and C3 tyres, with reference to the category of use of the range of tyres:
Tyre classCategory of useLimit values in dB(A)
C2Normal tyres72
Traction tyres73
C3Normal tyres73
Traction tyres75
For special use tyres, the above limits shall be increased by 2 dB(A). An additional 2 dB(A) shall be allowed for snow tyres in the C2 traction tyre category. For all other categories of C2 and C3 tyres, an additional 1 dB(A) shall be allowed for snow tyres.
ANNEX IIIAmendments to Directive 2007/46/ECDirective 2007/46/EC is hereby amended as follows:1.Part I of Annex IV shall be amended as follows:(a)the table shall be amended as follows:(i)points 3, 4, 5, 6, 7, 8, 9, 10, 12, 13, 14, 15, 16, 17, 18, 19, 20, 21, 22, 23, 24, 25, 26, 27, 28, 29, 30, 31, 32, 33, 34, 35, 36, 37, 38, 42, 43, 44, 45, 47, 48, 49, 50, 51, 52, 53, 54, 55, 56 and 57 shall be deleted;(ii)point 46 shall be deleted;(iii)the following row shall be added:
ItemSubjectRegulatory act referenceOfficial Journal referenceApplicability
M1M2M3N1N2N3O1O2O3O4
"63General safetyRegulation (EC) No 661/2009OJ L 200, 31.7.2009, p. 1.XXXXXXXXXX"
(b)the Appendix shall be amended as follows:(i)points 3, 4, 5, 6, 7, 8, 9, 10, 12, 13, 14, 15, 16, 17, 18, 19, 20, 21, 22, 23, 24, 25, 26, 27, 28, 29, 30, 31, 32, 33, 34, 35, 36, 37, 44, 45, 50, 51, 52, 53 and 54 of the table shall be deleted;(ii)point 46 of the table shall be deleted;(iii)the following row shall be added to the table:
SubjectRegulatory act referenceOfficial Journal referenceM1
"63General safetyRegulation (EC) No 661/2009OJ L 200, 31.7.2009, p. 1.P/A"
(iv)in the "Key", the following text shall be added:"P/AThis Regulation is partially applicable. The precise scope of application is established in the implementing measures to this Regulation."
2.In the Appendix to Annex VI, the table shall be amended as follows:(a)points 3 to 10, 12 to 38, 42 to 45 and 47 to 57 shall be deleted;(b)point 46 shall be deleted;(c)the following row shall be added:
SubjectRegulatory act reference (1)As amended byApplicable to versions
"63General safetyRegulation (EC) No 661/2009"
3.Annex XI shall be amended as follows:(a)in Appendix 1, the table shall be amended as follows:(i)points 3, 4, 5, 6, 7, 8, 9, 10, 12, 13, 14, 15, 16, 17, 18, 19, 20, 21, 22, 23, 24, 25, 26, 27, 28, 29, 30, 31, 32, 33, 34, 35, 36, 37, 38, 44, 45, 47, 48, 49, 50, 51, 52, 53 and 54 shall be deleted;(ii)point 46 shall be deleted;(iii)the following row shall be added:
ItemSubjectRegulatory act referenceM12500 (1) kgM1 > 2500 (1) kgM2M3
"63General safetyRegulation (EC) No 661/2009P/AP/AP/AP/A"
(b)in Appendix 2, the table shall be amended as follows:(i)points 3, 4, 5, 6, 7, 8, 9, 10, 12, 13, 14, 15, 16, 17, 18, 19, 20, 21, 22, 23, 24, 25, 26, 27, 28, 29, 30, 31, 32, 33, 34, 35, 36, 37, 38, 42, 43, 44, 45, 47, 48, 49, 50, 51, 52, 53, 54, 55, 56 and 57 shall be deleted;(ii)point 46 shall be deleted;(iii)the following row shall be added:
ItemSubjectRegulatory act referenceM1M2M3N1N2N3O1O2O3O4
"63General safetyRegulation (EC) No 661/2009P/AP/AP/AP/AP/AP/AP/AP/AP/AP/A"
(c)in Appendix 3, the table shall be amended as follows:(i)points 3, 4, 5, 6, 7, 8, 9, 10, 12, 13, 14, 15, 16, 17, 18, 19, 20, 21, 22, 23, 24, 25, 26, 27, 28, 29, 30, 31, 32, 33, 34, 35, 36, 37, 44, 45, 50, 51, 52, 53 and 54 shall be deleted;(ii)point 46 shall be deleted;(iii)the following row shall be added:
ItemSubjectRegulatory act referenceM1
"63General safetyRegulation (EC) No 661/2009P/A"
(d)in Appendix 4, the table shall be amended as follows:(i)points 3, 4, 5, 6, 7, 8, 9, 10, 13, 14, 15, 16, 17, 18, 19, 20, 21, 22, 23, 24, 25, 26, 27, 28, 29, 30, 31, 32, 33, 34, 35, 36, 42, 43, 44, 45, 47, 48, 49, 50, 51, 52, 53, 54, 55, 56 and 57 shall be deleted;(ii)point 46 shall be deleted;(iii)the following row shall be added:
ItemSubjectRegulatory act referenceM2M3N1N2N3O1O2O3O4
"63General safetyRegulation (EC) No 661/2009P/AP/AP/AP/AP/AP/AP/AP/AP/A"
(e)in Appendix 5, the table shall be amended as follows:(i)points 3, 4, 5, 6, 7, 8, 9, 10, 12, 13, 14, 15, 16, 17, 18, 19, 20, 21, 22, 23, 24, 25, 26, 27, 28, 29, 30, 31, 32, 33, 34, 35, 36, 42, 43, 44, 45, 47, 48, 49, 50, 51, 52, 53, 54, 55, 56 and 57 shall be deleted;(ii)point 46 shall be deleted;(iii)the following row shall be added:
ItemSubjectRegulatory act referenceMobile crane of category N3
"63General safetyRegulation (EC) No 661/2009P/A"
(f)the "Meaning of letters" shall be amended as follows:(i)points C, U, W5, and W6 shall be deleted;(ii)the following text shall be added:"P/AThis regulatory act is partially applicable. The precise scope of application is established in the implementing measures of this Regulation."
4.In the table in Annex XV, point 46 shall be deleted.
ANNEX IVList of UNECE Regulations which apply on a compulsory basis
Regulation NumberSubjectSeries of amendments published in the OJOJ ReferenceScope covered by the UNECE Regulation
1Headlamps emitting an asymmetrical passing beam and/or driving beam equipped with filament lamps R2 and/or HS102 series of amendmentsOJ L 177, 10.7.2010, p. 1.M, N (a)
3Retro-reflecting devices for power-driven vehiclesSupplement 12 to the 02 series of amendmentsOJ L 323, 6.12.2011, p. 1.M, N, O
4Illumination of rear-registration plates of power-driven vehicles and their trailersSupplement 15 to the original version of the RegulationOJ L 4, 7.1.2012, p. 7.M, N, O
6Direction indicators for power-driven vehicles and their trailersSupplement 25 to the 01 series of amendmentsOJ L 213, 18.7.2014, p. 1.M, N, O
7Front and rear position (side) lamps, stop-lamps and end-outline marker lamps for power-driven vehicles and their trailersSupplement 23 to the 02 series of amendmentsOJ L 285, 30.9.2014, p. 1.M, N, O
8Motor vehicles headlamps (H1, H2, H3, HB3, HB4, H7, H8, H9, HIR1, HIR2 and/or H11)05 series of amendments Corrigendum 1 to Revision 4OJ L 177, 10.7.2010, p. 71.M, N (a)
10Electromagnetic compatibilitySupplement 1 to the 05 series of amendmentsOJ L 41, 17.2.2017, p. 1.M, N, O
11Door latches and door retention componentsSupplement 2 to the 03 series of amendmentsOJ L 120, 13.5.2010, p. 1.M1, N1
12Protection of the driver against the steering mechanism in the event of impactSupplement 1 to the 04 series of amendmentsOJ L 89, 27.3.2013, p. 1.M1, N1
13Braking of vehicles and trailersSupplement 13 to the 11 series of amendmentsOJ L 42, 18.2.2016, p. 1.M2, M3, N, O (b)
13-HBraking of passenger carsSupplement 16 to the original version of the RegulationOJ L 335, 22.12.2015, p. 1.M1, N1 (c)
14Safety-belt anchorages, ISOFIX anchorages systems and ISOFIX top tether anchoragesSupplement 5 to the 07 series of amendmentsOJ L 218, 19.8.2015, p. 27.M, N
16Safety-belts, restraint systems, child restraint systems and ISOFIX child restraint systemsSupplement 2 to the 07 series of amendmentsOJ L 109, 27.4.2018, p. 1.M, N (d)
17Seats, their anchorages and any head restraints08 series of amendmentsOJ L 230, 31.8.2010, p. 81.M, N
18Protection of motor vehicles against unauthorized useSupplement 2 to the 03 series of amendmentsOJ L 120, 13.5.2010, p. 29.M2, M3, N2, N3
19Power-driven vehicle front fog lampsSupplement 6 to the 04 series of amendmentsOJ L 250, 22.8.2014, p. 1.M, N
20Headlamps emitting an asymmetrical passing beam or a driving beam or both and equipped with halogen filament lamps (H4)03 series of amendmentsOJ L 177, 10.7.2010, p. 170.M, N (a)
21Interior fittingsSupplement 3 to the 01 series of amendmentsOJ L 188, 16.7.2008, p. 32.M1
23Reversing lights for power-driven vehicles and their trailersSupplement 19 to the original version of the RegulationOJ L 237, 8.8.2014, p. 1.M, N, O
25Head restraints (headrests), whether or not incorporated in vehicle seats04 series of amendments Corrigendum 2 to Revision 1OJ L 215, 14.8.2010, p. 1.M1
26External projectionsSupplement 1 to the 03 series of amendmentsOJ L 215, 14.8.2010, p. 27.M1
28Audible warning devices and signalsSupplement 3 to the original version of the RegulationOJ L 323, 6.12.2011, p. 33.M, N
29Protection of the occupants of the cab of a commercial vehicle03 series of amendmentsOJ L 304, 20.11.2010, p. 21.N
30Pneumatic tyres for motor vehicles and their trailers (Class C1)Supplement 16 to the 02 series of amendmentsOJ L 307, 23.11.2011, p. 1.M, N, O
31Power-driven vehicle's sealed-beam headlamps (SB) emitting an European asymmetrical passing beam or a driving beam or bothSupplement 7 to the 02 series of amendmentsOJ L 185, 17.7.2010, p. 15.M, N
34Prevention of fire risks (liquid fuel tanks)Supplement 1 to the 03 series of amendmentsOJ L 231, 26.8.2016, p. 41.M, N, O (e)
37Filament lamps for use in approved lamp units of power-driven vehicles and their trailersSupplement 42 to the 03 series of amendmentsOJ L 213, 18.7.2014, p. 36.M, N, O
38Rear fog lamps for power-driven vehicles and their trailersSupplement 15 to the original version of the RegulationOJ L 4, 7.1.2012, p. 20.M, N, O
39Speedometer equipment including its installationSupplement 1 to the 01 series of amendmentsOJ L 302, 28.11.2018, p. 106M, N
43Safety glazing materialsSupplement 2 to the 01 series of amendmentsOJ L 42, 12.2.2014, p. 1.M, N, O
44Restraining devices for child occupants of power-driven vehicles ("child restraint system")Supplement 10 to the 04 series of amendmentsOJ L 265, 30.9.2016, p. 1.M, N (h)
46Devices for indirect vision and their installationSupplement 1 to the 04 series of amendmentsOJ L 237, 8.8.2014, p. 24.M, N
48Installation of lighting and light-signalling devices on motor vehiclesSupplement 10 to the 06 series of amendmentsOJ L 14, 16.1.2019, p. 42M, N, O
54Pneumatic tyres for commercial vehicles and their trailers (Classes C2 and C3)Supplement 17 to the original version of the RegulationOJ L 307, 23.11.2011, p. 2.M, N, O
55Mechanical coupling components of combinations of vehiclesSupplement 1 to the 01 series of amendmentsOJ L 227, 28.8.2010, p. 1.M, N, O (f)
58Rear underrun protective devices (RUPDs) and their installation; Rear underrun protection (RUP)03 series of amendmentsOJ L 49, 20.2.2019, p. 1.M, N, O
61Commercial vehicles with regard to their external projections forward of the cab's rear panelSupplement 1 to the original version of the RegulationOJ L 164, 30.6.2010, p. 1.N
64Temporary-use spare unit, run-flat tyres/system and tyre pressure monitoring systemCorrigendum 1 to the 02 series of amendmentsOJ L 310, 26.11.2010, p. 18.M1, N1
66Strength of the superstructure of large passenger vehicles02 series of amendmentsOJ L 84, 30.3.2011, p. 1.M2, M3
67Motor vehicles using LPGSupplement 14 to the 01 series of amendmentsOJ L 285, 20.10.2016, p. 1.M, N
73Lateral protection of goods vehicles01 series of amendmentsOJ L 122, 8.5.2012, p. 1.N2, N3, O3, O4
77Parking lamps for power-driven vehiclesSupplement 14 to the original version of the RegulationOJ L 4, 7.1.2012, p. 21.M, N
79Steering equipment03 series of amendmentsOJ L 318, 14.12.2018, p. 1.M, N, O
80Seats of large passenger vehicles03 series of amendments to the RegulationOJ L 226, 24.8.2013, p. 20.M2, M3
87Daytime running lamps for power-driven vehiclesSupplement 15 to the original version of the RegulationOJ L 4, 7.1.2012, p. 24.M, N
89Speed limitation devicesSupplement 2 to the original version of the RegulationOJ L 4, 7.1.2012, p. 25.M, N (g)
90Replacement brake lining assemblies and drum brake linings for power-driven vehicles and their trailers02 series of amendmentsOJ L 185, 13.7.2012, p. 24.M, N, O
91Side-marker lamps for motor vehicles and their trailersSupplement 13 to the original version of the RegulationOJ L 4, 7.1.2012, p. 27.M, N, O
93Front underrun protective devices (FUPDs) and their installation; front underrun protection (FUP)Original version of the RegulationOJ L 185, 17.7.2010, p. 56.N2, N3
94Protection of occupants in the event of a frontal collision03 series of amendmentsOJ L 35, 8.2.2018, p. 1.M1
95Protection of occupants in the event of a lateral collisionSupplement 4 to the 03 series of amendmentsOJ L 183, 10.7.2015, p. 91.M1, N1
97Vehicle Alarm Systems (VAS)Supplement 6 to the 01 series of amendmentsOJ L 122, 8.5.2012, p. 19.M1, N1
98Motor vehicle headlamps equipped with gas-discharge light sourcesSupplement 4 to the 01 series of amendmentsOJ L 176, 14.6.2014, p. 64.M, N
99Gas-discharge light sources for use in approved gas-discharge lamp units of power-driven vehiclesSupplement 9 to the original version of the RegulationOJ L 285, 30.9.2014, p. 35.M, N
100Electric safetySupplement 3 to the 02 series of amendmentsOJ L 302, 28.11.2018, p. 114.M, N
102Close-coupling device (CCD); fitting of an approved type of CCDOriginal version of the RegulationOJ L 351, 30.12.2008, p. 44.N2, N3, O3, O4
104Retro-reflective markings (heavy and long vehicles)Supplement 7 to the original versionOJ L 75, 14.3.2014, p. 29.M2, M3, N, O2, O3, O4
105Vehicles for the carriage of dangerous goods05 series of amendmentsOJ L 4, 7.1.2012, p. 30.N, O
107M2 and M3 vehiclesSupplement 1 to the 07 series of amendmentsOJ L 52, 23.2.2018, p. 1.M2, M3
110Specific components for CNGSupplement 2 to 01 series of amendmentsOJ L 166, 30.6.2015, p. 1.M, N
112Motor vehicle headlamps emitting an asymmetrical passing beam or a driving beam or both and equipped with filament lamps and/or LED modulesSupplement 4 to the 01 series of amendmentsOJ L 250, 22.8.2014, p. 67.M, N
116Protection of motor vehicles against unauthorized useSupplement 3 to the original version of the RegulationOJ L 45, 16.2.2012, p. 1.M1, N1
117Tyres with regard to rolling sound emissions, adhesion on wet surfaces and rolling resistance (Classes C1, C2 and C3)Supplement 8 to the 02 series of amendmentsOJ L 218, 12.8.2016, p. 1.M, N, O
118Fire resistance of materials used in busesSupplement 1 to the 02 series of amendmentsOJ L 102, 21.4.2015, p. 67.M3
119Cornering lampsSupplement 3 to the 01 series of amendmentsOJ L 89, 25.3.2014, p. 101.M, N (h)
121Location and identification of hand controls, tell-tales and indicators01 series of amendmentsOJ L 5, 8.1.2016, p. 9.M, N
122Heating system of vehiclesSupplement 1 to the original version of the RegulationOJ L 164, 30.6.2010, p. 231.M, N, O
123Adaptive front-lighting systems (AFS)Supplement 9 to the 01 series of amendmentsOJ L 49, 20.2.2019, p. 24.M, N
125Forward field of visionSupplement 1 to the 01 series of amendmentsOJ L 20, 25.1.2018, p. 16.M1
128Light Emitting Diode (LED) light sourcesSupplement 6 to the original version of the RegulationOJ L 320, 17.12.2018, p. 63.M, N, O
140Stability controlSupplement 2 to the original version of the RegulationOJ L 269, 26.10.2018, p. 17.M1, N1
141Tyre Pressure Monitoring Systems (TPMS)Original version of the RegulationOJ L 269, 26.10.2018, p. 36.M1, N1 (i)
Notes to the table:The transitional provisions of the UNECE regulations listed in this table apply, except where specific alternative dates are provided for in this Regulation. Compliance with prescriptions in accordance with subsequent amendments to those listed in this table shall also be accepted.The dates specified in the UNECE regulations listed in this table, as regards the obligations of Contracting Parties to the "Revised 1958 Agreement" (Council Decision of 27 November 1997 with a view to accession by the European Community to the Agreement of the United Nations Economic Commission for Europe concerning the adoption of uniform technical prescriptions for wheeled vehicles, equipment and parts which can be fitted to and/or be used on wheeled vehicles and the conditions for reciprocal recognition of approvals granted on the basis of these prescriptions ("Revised 1958 Agreement") (OJ L 346, 17.12.1997, p. 78).), linked to first registration, entry into service, making available on the market, sale, and any similar provisions, apply on a compulsory basis for the purposes of Articles 26 and 28 of Directive 2007/46/EC except in the case where alternative dates are specified in Regulation (EC) No 661/2009, which should then be taken instead.In certain instances, a UNECE regulation listed in this table provides in its transitional provisions that as from a specified date, Contracting Parties to the "Revised 1958 Agreement", applying a certain series of amendments to that UNECE regulation, shall not be obliged to accept or may refuse to accept, for the purpose of national or regional type-approval, a type approved in accordance with a preceding series of amendments, or wording with similar intention and meaning. This shall be construed as a binding provision for national authorities to consider the certificates of conformity to be no longer valid for the purposes of Article 26 of Directive 2007/46/EC, except in the case where alternative dates are specified in Regulation (EC) No 661/2009, which should then be taken instead.(a)UNECE Regulation Nos 1, 8 and 20 are not applicable for EC type-approval of new vehicles.(b)The fitting of an electronic stability control system is required in accordance with Article 12(1) and (2) of Regulation (EC) No 661/2009.(c)The fitting of an electronic stability control system is required in accordance with Article 12(1) and (2) of Regulation (EC) No 661/2009.(d)A safety-belt reminder is not required for a driver position equipped with an S-type belt or Harness belt.(e)Compliance with Part II of UNECE Regulation No 34 is not compulsory.(f)Where it is declared by the vehicle manufacturer that a vehicle is suitable for towing loads (point 2.11.5 of Annex I to Directive 2007/46/EC) and any part of a suitable mechanical coupling device, whether fitted or not to the type of motor-vehicle, could (partly) obscure any lighting component and/or the space for mounting and fixing the rear registration plate, the following shall apply:the motor-vehicle's user instructions (e.g. owner's manual, vehicle handbook) shall clearly specify that installation of a mechanical coupling device that cannot be easily removed or repositioned is not permitted;the instructions shall also clearly specify that, when fitted, a mechanical coupling device must always be removed or repositioned when it is not in use; andin the case of vehicle system type-approval according to UN Regulation 55, it shall be ensured that the removal, repositioning and/or alternate location provisions are also fully complied with as regards lighting installation and space for mounting and fixing the rear registration plate.(g)Only Speed Limitation Devices (SLD) and the mandatory installation of SLD on vehicles of category M2, M3, N2 and N3 are concerned.(h)A Universal International Whole Vehicle Type Approval issued under UN Regulation No 0 (OJ L 135, 31.5.2018, p. 1), that includes type-approval under the respective UN Regulations in the table that refer to this note, shall be considered equivalent to an EC type-approval granted under this Regulation.(i)Tyre pressure monitoring system for M1 vehicles applies on a compulsory basis in accordance with Article 9(2) of Regulation (EC) No 661/2009. UN Regulation No 141 applies to the approval of vehicles of category M1 up to a maximum mass of 3500 kg. UN Regulation No 141 may apply on voluntary basis to the approval of vehicles of category N1 that are not fitted with twin wheels on an axle.
ANNEX VImplementation dates of the requirements for electronic stability control systems on vehicles of categories M2, M3, N2, N3, O3 and O4
Table 1 —Implementation dates for new types of vehicle
Vehicle categoryImplementation date
M211 July 2013
M3 (Class III)1 November 2011
M3 < 16 tonnes (pneumatic transmission)1 November 2011
M3 (Class II and B) (hydraulic transmission)11 July 2013
M3 (Class III) (hydraulic transmission)11 July 2013
M3 (Class III) (pneumatic control transmission and hydraulic energy transmission)11 July 2014
M3 (Class II) (pneumatic control transmission and hydraulic energy transmission)11 July 2014
M3 (other than above)1 November 2011
N2 (hydraulic transmission)11 July 2013
N2 (pneumatic control transmission and hydraulic energy transmission)11 July 2014
N2 (other than above)11 July 2012
N3 (2 axle tractors for semi-trailers)1 November 2011
N3 (2 axle tractors for semi-trailers with pneumatic control transmission (ABS))1 November 2011
N3 (3 axles with electric control transmission (EBS))1 November 2011
N3 (2 and 3 axles with pneumatic control transmission (ABS))11 July 2012
N3 (other than above)1 November 2011
O3 (combined axle load between 3.5 and 7.5 tonnes)11 July 2012
O3 (other than above)1 November 2011
O41 November 2011
Table 2 —Implementation dates for new vehicles
Vehicle categoryImplementation date
M211 July 2015
M3 (Class III)1 November 2014
M3 < 16 tonnes (pneumatic transmission)1 November 2014
M3 (Class II and B) (hydraulic transmission)11 July 2015
M3 (Class III) (hydraulic transmission)11 July 2015
M3 (Class III) (pneumatic control transmission and hydraulic energy transmission)11 July 2016
M3 (Class II) (pneumatic control transmission and hydraulic energy transmission)11 July 2016
M3 (other than above)1 November 2014
N2 (hydraulic transmission)11 July 2015
N2 (pneumatic control transmission and hydraulic energy transmission)11 July 2016
N2 (other than above)1 November 2014
N3 (2 axle tractors for semi-trailers)1 November 2014
N3 (2 axle tractors for semi-trailers with pneumatic control transmission (ABS))1 November 2014
N3 (3 axles with electric control transmission (EBS))1 November 2014
N3 (2 and 3 axles with pneumatic control transmission (ABS))1 November 2014
N3 (other than above)1 November 2014
O3 (combined axle load between 3.5 and 7.5 tonnes)1 November 2014
O3 (other than above)1 November 2014
O41 November 2014