(a) fuels intended for the purposes of research and testing; (b) fuels intended for processing prior to final combustion; (c) fuels to be processed in the refining industry; (d) fuels used and placed on the market in the outermost regions of the Community provided that the relevant Member States ensure that, in those regions: air quality standards are respected, heavy fuel oils are not used if their sulphur content exceeds 3 % by mass;
(e) fuels used by warships and other vessels on military service. However, each Member State shall endeavour to ensure, by the adoption of appropriate measures not impairing the operations or operational capability of such ships, that these ships act in a manner consistent, so far as is reasonable and practical, with this Directive; (f) any use of fuels in a vessel necessary for the specific purpose of securing the safety of a ship or saving life at sea; (g) any use of fuels in a ship necessitated by damage sustained to it or its equipment, provided that all reasonable measures are taken after the occurrence of the damage to prevent or minimise excess emissions and that measures are taken as soon as possible to repair the damage. This shall not apply if the owner or master acted either with intent to cause damage, or recklessly; (h) without prejudice to Article 3a, fuels used on board vessels employing emission abatement methods in accordance with Articles 4c and 4e.
Council Directive 1999/32/EC of 26 April 1999 relating to a reduction in the sulphur content of certain liquid fuels and amending Directive 93/12/EEC
Modified by
- Regulation (EC) No 1882/2003 of the European Parliament and of the Councilof 29 September 2003adapting to Council Decision 1999/468/EC the provisions relating to committees which assist the Commission in the exercise of its implementing powers laid down in instruments subject to the procedure referred to in Article 251 of the EC Treaty, 32003R1882, October 31, 2003
- Directive 2005/33/EC of the European Parliament and of the Councilof 6 July 2005amending Directive 1999/32/EC, 32005L0033, July 22, 2005
- Regulation (EC) No 219/2009 of the European Parliament and of the Councilof 11 March 2009adapting a number of instruments subject to the procedure referred to in Article 251 of the Treaty to Council Decision 1999/468/EC with regard to the regulatory procedure with scrutinyAdaptation to the regulatory procedure with scrutiny — Part Two, 32009R0219, March 31, 2009
- Directive 2009/30/EC of the European Parliament and of the Councilof 23 April 2009amending Directive 98/70/EC as regards the specification of petrol, diesel and gas-oil and introducing a mechanism to monitor and reduce greenhouse gas emissions and amending Council Directive 1999/32/EC as regards the specification of fuel used by inland waterway vessels and repealing Directive 93/12/EEC(Text with EEA relevance), 32009L0030, June 5, 2009
- Directive 2012/33/EU of the European Parliament and of the Councilof 21 November 2012amending Council Directive 1999/32/EC as regards the sulphur content of marine fuels, 32012L0033, November 27, 2012
- Directive (EU) 2016/802 of the European Parliament and of the Councilof 11 May 2016relating to a reduction in the sulphur content of certain liquid fuels(codification), 32016L0802, May 21, 2016
1. heavy fuel oil means:any petroleum-derived liquid fuel, excluding marine fuel, falling within CN code 27101951 to27101968 ,27102031 ,27102035 ,27102039 , orany petroleum-derived liquid fuel, other than gas oil as defined in points 2 and 3, which, by reason of its distillation limits, falls within the category of heavy oils intended for use as fuel and of which less than 65 % by volume (including losses) distils at 250 °C by the ASTM D86 method. If the distillation cannot be determined by the ASTM D86 method, the petroleum product is likewise categorised as a heavy fuel oil;
2. gas oil means:any petroleum-derived liquid fuel, excluding marine fuel, falling within CN code 27101925 ,27101929 ,27101947 ,27101948 ,27102017 or27102019 , orany petroleum-derived liquid fuel, excluding marine fuel, of which less than 65 % by volume (including losses) distils at 250 °C and of which at least 85 % by volume (including losses) distils at 350 °C by the ASTM D86 method.
Diesel fuels as defined in point 2 of Article 2 of Directive 98/70/EC of the European Parliament and of the Council of 13 October 1998 relating to the quality of petrol and diesel fuels are excluded from this definition. Fuels used in non-road mobile machinery and agricultural tractors are also excluded from this definition;OJ L 350, 28.12.1998, p. 58 .3. marine fuel means any petroleum-derived liquid fuel intended for use or in use on board a vessel, including those fuels defined in ISO 8217. It includes any petroleum-derived liquid fuel in use on board inland waterway vessels or recreational craft, as defined in Directive 97/68/EC of the European Parliament and of the Council of16 December 1997 on the approximation of the laws of the Member States relating to measures against the emission of gaseous and particulate pollutants from internal combustion engines to be installed in non-road mobile machinery and Directive 94/25/EC of the European Parliament and of the Council ofOJ L 59, 27.2.1998, p. 1 .16 June 1994 on the approximation of the laws, regulations and administrative provisions of the Member States relating to recreational craft , when such vessels are at sea;OJ L 164, 30.6.1994, p. 15 .3a. marine diesel oil means any marine fuel as defined for DMB grade in Table I of ISO 8217 with the exception of the reference to the sulphur content;3b. marine gas oil means any marine fuel as defined for DMX, DMA and DMZ grades in Table I of ISO 8217 with the exception of the reference to the sulphur content;3c. MARPOL means the International Convention for the Prevention of Pollution from Ships, 1973, as modified by the Protocol of 1978 relating thereto;3d. Annex VI to MARPOL means the annex, entitled "Regulations for the Prevention of Air Pollution from Ships", that the Protocol of 1997 adds to MARPOL;3e. Ox Emission Control Areas means sea areas defined as such by the IMO under Annex VI to MARPOL;3f. passenger ships means ships that carry more than 12 passengers, where a passenger is every person other than:(i) the master and the members of the crew or other person employed or engaged in any capacity on board a ship on the business of that ship, and (ii) a child under one year of age;
3g. regular services means a series of passenger ship crossings operated so as to serve traffic between the same two or more ports, or a series of voyages from and to the same port without intermediate calls, either:(i) according to a published timetable, or (ii) with crossings so regular or frequent that they constitute a recognisable schedule;
3h. warship means a ship belonging to the armed forces of a State bearing the external marks distinguishing such ships of its nationality, under the command of an officer duly commissioned by the government of the State and whose name appears in the appropriate service list or its equivalent, and manned by a crew which is under regular armed forces discipline;3i. ships at berth means ships which are securely moored or anchored in a Community port while they are loading, unloading or hotelling, including the time spent when not engaged in cargo operations;3j. inland waterway vessel means a vessel particularly intended for use on an inland waterway as defined in Council Directive 82/714/EEC of4 October 1982 laying down technical requirements for inlandwaterway vessels , including all vessels which carry:OJ L 301, 28.10.1982, p. 1 . Directive as last amended by the 2003 Act of Accession.(i) a Community inlandnavigation certificate, as defined in Directive 82/714/EEC, (ii) a certificate issued pursuant to Article 22 of the Revised Convention for the Navigation of the Rhine;
3k. placing on the market means supplying or making available to third persons, against payment or free of charge, anywhere within Member States' jurisdictions, marine fuels for on-board combustion. It excludes supplying or making available marine fuels for export in ships' cargo tanks;3l. outermost regions means the French overseas departments, the Azores, Madeira and the Canary Islands, as set out in Article 299 of the Treaty;3m. emission abatement method means any fitting, material, appliance or apparatus to be fitted in a ship or other procedure, alternative fuel, or compliance method, used as an alternative to low sulphur marine fuel meeting the requirements set out in this Directive, that is verifiable, quantifiable and enforceable;4. ASTM method means the methods laid down by the American Society for Testing and Materials in the 1976 edition of standard definitions and specifications for petroleum and lubricating products;5. combustion plant means any technical apparatus in which fuels are oxidised in order to use the heat generated.6. critical load means a quantitative estimate of exposure to one or more pollutants below which significant harmful effects on sensitive elements of the environment do not occur according to current knowledge.
(a) in combustion plants which fall within the scope of Directive 2001/80/EC of the European Parliament and of the Council of 23 October 2001 on the limitation of emissions of certain pollutants into the air from large combustion plants , which are subject to Article 4(1) or (2) or Article 4(3)(a) of that Directive and which comply with the emission limits for sulphur dioxide for such plants as set out in that Directive;OJ L 309, 27.11.2001, p. 1 .(b) in combustion plants which fall within the scope of Directive 2001/80/EC, which are subject to Article 4(3)(b) and Article 4(6) of that Directive and the monthly average sulphur dioxide emissions of which do not exceed 1700 mg/Nm3 at an oxygen content in the flue gas of 3 % by volume on a dry basis;(c) in combustion plants which do not fall under points (a) or (b), and the monthly average sulphur dioxide emissions of which do not exceed 1700 mg/Nm3 at an oxygen content in the flue gas of 3 % by volume on a dry basis;(d) for combustion in refineries, where the monthly average of emissions of sulphur dioxide averaged over all combustion plants in the refinery, irrespective of the type of fuel or fuel combination used, but excluding plants which fall under points (a) and (b), gas turbines and gas engines, do not exceed 1700 mg/Nm3 at an oxygen content in the flue gas of 3 % by volume on a dry basis.
(a) in combustion plants which fall within the scope of Chapter III of Directive 2010/75/EU of the European Parliament and of the Council , and which comply with the emission limits for sulphur dioxide for such plants as set out in Annex V to that Directive or, where those emission limit values are not applicable according to that Directive, for which the monthly average sulphur dioxide emissions do not exceedOJ L 334, 17.12.2010, p. 17 .1700 mg/Nm3 at an oxygen content in the flue gas of 3 % by volume on a dry basis;(b) in combustion plants which do not fall under point (a), and the monthly average sulphur dioxide emissions of which do not exceed 1700 mg/Nm3 at an oxygen content in the flue gas of 3 % by volume on a dry basis;(c) for combustion in refineries, where the monthly average of emissions of sulphur dioxide averaged over all combustion plants in the refinery, irrespective of the type of fuel or fuel combination used, but excluding plants falling under point (a), gas turbines and gas engines, do not exceed 1700 mg/Nm3 at an oxygen content in the flue gas of 3 % by volume on a dry basis.
(a) 1,00 % until 31 December 2014 ;(b) 0,10 % as from 1 January 2015 .
(a) 3,50 % as from 18 June 2014 ;(b) 0,50 % as from 1 January 2020 .
(a) for the Baltic Sea area referred to in regulation 14(3)(a) of Annex VI to MARPOL, 11 August 2006 ;(b) for the North Sea: 12 months after entry into force of the IMO designation, according to established procedures, or 11 August 2007 ,
whichever is the earlier; (c) for any other sea areas, including ports, that the IMO subsequently designates as SOx Emission Control Areas in accordance with regulation 14(3)(b) of Annex VI to MARPOL: 12 months after the date of entry into force of the designation.
vessels flying their flag, and in the case of Member States bordering SOx Emission Control Areas, vessels of all flags while in their ports.
(a) present a record of the actions taken to attempt to achieve compliance; and (b) provide evidence that it attempted to purchase marine fuel which complies with this Directive in accordance with its voyage plan and, if it was not made available where planned, that attempts were made to locate alternative sources for such marine fuel and that, despite best efforts to obtain marine fuel which complies with this Directive, no such marine fuel was made available for purchase.
(a) maintain a publicly available register of local suppliers of marine fuel; (b) ensure that the sulphur content of all marine fuels sold in their territory is documented by the supplier on a bunker delivery note, accompanied by a sealed sample signed by the representative of the receiving ship; (c) take action against marine fuel suppliers that have been found to deliver fuel that does not comply with the specification stated on the bunker delivery note; (d) ensure that remedial action is taken to bring any non-compliant marine fuel discovered into compliance.
(a) whenever, according to published timetables, ships are due to be at berth for less than two hours; (b) to ships which switch off all engines and use shore-side electricity while at berth in ports.
(a) be empowered to adopt delegated acts in accordance with Article 9a amending Annexes I and II; (b) adopt implementing acts laying down the detailed requirements for monitoring of emissions, where appropriate. Those implementing acts shall be adopted in accordance with the examination procedure referred to in Article 9(2).;
(a) guidelines developed by the IMO; (b) the results of any trials conducted under Article 4e; (c) effects on the environment, including achievable emission reductions, and impacts on ecosystems in enclosed ports, harbours and estuaries; and (d) the feasibility of monitoring and verification.
(a) the Commission and any port State concerned are notified in writing at least six months before trials begin; (b) permits for trials do not exceed 18 months in duration; (c) all ships involved install tamper-proof equipment for the continuous monitoring of funnel gas emissions and use it throughout the trial period; (d) all ships involved achieve emission reductions which are at least equivalent to those which would be achieved through the sulphur limits for fuels specified in this Directive; (e) there are proper waste management systems in place for any waste generated by the emission abatement methods throughout the trial period; (f) there is an assessment of impacts on the marine environment, particularly ecosystems in enclosed ports, harbours and estuaries throughout the trial period; and (g) full results are provided to the Commission, and made publicly available, within six months of the end of the trials.
(a) inspection of ships' log books and bunker delivery notes; and, as appropriate, the following means of sampling and analysis: (b) sampling of the marine fuel for on-board combustion while being delivered to ships, in accordance with the Guidelines for the sampling of fuel oil for determination of compliance with the revised MARPOL Annex VI adopted on 17 July 2009 by Resolution 182(59) of the Marine Environment Protection Committee (MEPC) of the IMO, and analysis of its sulphur content; or(c) sampling and analysis of the sulphur content of marine fuel for on-board combustion contained in tanks, where technically and economically feasible, and in sealed bunker samples on board ships.
(a) the frequency of sampling; (b) the sampling methods; (c) the definition of a sample representative of the fuel examined.
(a) in Article 1, paragraph 1(a) and paragraph 2 are deleted; (b) in Article 2, the first subparagraph of paragraph 2 and paragraph 3 are deleted; (c) Articles 3 and 4 are deleted.
Marine fuel Sulphur Content (% m/m) | Ratio Emission SO |
---|---|
The use of the Ratio Emissions limits is only applicable when using petroleum based Distillate or Residual Fuel Oils. In justified cases where the CO 2 concentration is reduced by the exhaust gas cleaning (EGC) unit, the CO2 concentration may be measured at the EGC unit inlet, provided that the correctness of such a methodology can be clearly demonstrated.
Emission abatement method | Criteria for use |
---|---|
Mixture of marine fuel and boil-off gas | Commission Decision 2010/769/EU of |
Exhaust gas cleaning systems | |
Biofuels |