Article 1 This Regulation, laying down technical conservation measures, shall apply to the taking and landing of fishery resources occurring in the maritime waters under the sovereignty or jurisdiction of the Member States and situated in one of the regions specified in Article 2, except as otherwise provided in Articles 26 and 33.

Article 1a In Article 4(2)(c), Article 46(1)(b) and in Annex I, footnote (5), the noun "Community", or the corresponding adjective, is replaced by the noun "Union", or the corresponding adjective, and any grammatical adjustments needed as a consequence of this replacement shall be made.

TITLE I DEFINITIONS

Article 2 1. For the purposes of this Regulation, the following definitions of maritime waters shall apply: (a)Region 1 All waters which lie to the north and west of a line running from a point at latitude 48o N, longitude 18o W, thence due north to latitude 60o N, thence due east to latitude 5o W, thence due north to latitude 60o 30′ N, thence due east to longitude 4o W, thence due north to latitude 64o N, thence due east to the coast of Norway. (b)Region 2 All waters situated north of latitude 48o N, but excluding the waters in Region 1 and ICES divisions IIIb, IIIc, and IIId. (c)Region 3 All waters corresponding to ICES sub-areas VIII and IX. (d)Region 4 All waters corresponding to ICES sub-area X. (e)Region 5 All waters in that part of the east central Atlantic comprising divisions 34.1.1, 34.1.2 and 34.1.3 and sub-area 34.2.0 of fishing zone 34 of the CECAF region. (f)Region 6 All waters off the coasts of the French department of Guyana that come under the sovereignty or jurisdiction of France. (g)Region 7 All waters off the coasts of the French departments of Martinique and Guadeloupe that come under the sovereignty or jurisdiction of France. (h)Region 8 All waters off the coasts of the French departments of Réunion and Mayotte that fall under the sovereignty or jurisdiction of France. (i)Region 9 All waters of the Black Sea corresponding to the geographical sub-area 29 as defined in Annex I to Regulation (EU) No 1343/2011 of the European Parliament and of the Council of 13 December 2011 on certain provisions for fishing in the GFCM (General Fisheries Commission for the Mediterranean) Agreement areaOJ L 347, 30.12.2011, p. 44. and in Resolution GFCM/33/2009/2. 2. The geographical areas designated in this Regulation by the letters "ICES"and "CECAF"shall be those defined by the International Council for the Exploration of the Sea and the Fishery Committee for the Eastern Central Atlantic, respectively. They are described, subject to any subsequent amendments, in Commission communications No 85/C 335/02OJ C 335, 24.12.1985, p. 2. and No 85/C 347/05OJ C 347, 31.12.1985, p. 14.. 3. The regions referred to in paragraph 1 may be divided into geographical areas, in particular on the basis of the definitions referred to in paragraph 2, in accordance with the procedure referred to in Article 48. 4. Notwithstanding paragraph 2, for the purposes of this Regulation: the Kattegat is limited in the north by a line drawn from Skagen Lighthouse to the lighthouse in Tistlarna, and from there to the nearest point on the Swedish coast, and in the south by a line drawn from Hasenøre Head to Gniben Point, from Korshage to Spodsbjerg, and from Gilbjerg Head to the Kullen, the Skagerrak is limited in the west by a line drawn form the lighthouse of Hanstholm to the lighthouse of Lindesnes, and in the south by a line drawn form Skagen Lighthouse to the lighthouse of Tistlarna, and from there to the nearest point on the Swedish coast, the North Sea shall comprise ICES sub-area IV, the adjacent part of ICES Division IIa lying south of latitude 64o N, and that part of ICES Division IIIa which is not covered by the definition of the Skagerrak given in the second indent.

Article 3 For the purposes of this Regulation: (a) marine organismsshall mean all marine fish, including anadromous and catadromous species during their marine life, crustaceans and molluscs and parts thereof; (b) mesh sizeof a towed net shall mean the mesh size of any cod-end or extension piece found on board a fishing vessel and attached to or suitable for attachment to any towed net. The mesh size shall be determined by procedures specified in Regulation (EEC) No 2108/84OJ L 194 24.7.1984, p. 22.. This definition of mesh size shall not be applied to mesh size of square-meshed netting; (c) multiple twine nettingshall mean netting constructed of two or more twines, where the twines can be separated between the knots without damage to the twine structure; (d) square-meshed nettingshall mean a construction of netting mounted so that of the two sets of parallel lines formed by the mesh bars, one set is parallel to, and the other at right angles to, the long axis of the net; (e) mesh size of a square-meshed panel or windowshall mean the largest determinable mesh size of such a panel or window inserted into a towed net. The mesh size shall be determined by procedures in Regulation (EEC) No 2108/84; (f) knotless nettingshall mean netting which is composed of meshes of four sides of approximately equal length in which the corners of the meshes are formed by the interweaving of the twines of two adjacent sides of the mesh; (g) bottom set gill nets or entangling netsshall mean any fixed gear made up of a single piece of net, fixed, or capable of being fixed, by any means to the bottom of the sea; (h) trammel netsshall mean any fixed gear made up of two or more pieces of net hung jointly in parallel on a single headline, fixed, or capable of being fixed, by any means to the bottom of the sea.

TITLE II NETS AND CONDITIONS FOR THEIR USE CHAPTER I PROVISIONS FOR TOWED GEARS

Article 4 1. For each of the regions or geographical areas mentioned in Annexes I to V, and depending where applicable on the time period, the target species for each range of mesh size are as defined in the relevant Annex. 2. (a)The use, during any fishing voyage, of any combination of towed nets of more than one range of mesh size shall be prohibited, within the totality of Regions l and 2 except Skagerrak and Kattegat, and depending where applicable on the time period, unless the mesh sizes of such nets used are in compliance with no more than one of the permitted combinations of mesh size ranges laid down in Annex VIII, and within Region 3 except ICES Division IXa east of longitude 7o 23′ 48″ W unless the mesh sizes of such nets used are in compliance with no more than one of the permitted combinations of mesh size ranges laid down in Annex IX. (b)Within each of the regions or geographical areas mentioned in Annexes III, IV, and V, and depending, where applicable, on the time period, the use, during any fishing voyage, of any combination of towed nets of the mesh size ranges specified in the relevant Annex shall be allowed. (c)Masters of fishing vessels who during any fishing voyage do not complete a logbook in accordance with the provisions of Article 6 of Regulation (EEC) No 2847/93 shall not use during that voyage any combination of towed nets of more than one range of mesh size within Community fishing waters. This requirement shall not apply to fishing voyages within Community fishing waters in Regions 4, 5 and 6. (d)Vessels may carry on board during any fishing voyage any combination of towed nets of mesh size ranges which do not comply with the conditions laid down in subparagraphs (a) or (b), provided that all such nets are lashed and stowed in accordance with the provisions of Article 20(1) of Regulation (EEC) No 2847/93. Any towed net which is not lashed and stowed in accordance with the aforementioned provisions shall be considered to be in use. (e)Whenever more than one net is towed simultaneously by a fishing vessel or by more than one fishing vessel, each net shall be of the same mesh size range. (f)The use of any towed net of mesh size: less than 16 mm shall be prohibited in Region 3 except ICES Division IXa east of longitude 7o 23′ 48″ W, less than 40 mm shall be prohibited in ICES Division IXa east of longitude 7o 23′ 48″ W, less than 20 mm shall be prohibited in Regions 4 and 5, less than 45 mm shall be prohibited in Region 6. 3. Masters of fishing vessels who do not complete a logbook in accordance with the provisions of Article 6 of Regulation (EEC) No 2847/93 shall not, during any fishing voyage, fish in more than one of the regions or geographical areas mentioned in Annexes I to V. This requirement shall not apply to vessels which, during any fishing voyage, use only towed nets of mesh size equal to or greater than 100 mm. 4. (a)For each fishing voyage during which any combination of towed nets of more than one range of mesh size is used, landings shall be prohibited whenever: (i)the catches are taken in Regions 1 or 2 except for the Skagerrak and Kattegat and any one of the nets used is of mesh size equal to or greater than 100 mm, unless the percentage composition of the catches retained on board is in compliance with the relevant conditions laid down in Annex X(A); or (ii)the catches are taken in the Skagerrak and Kattegat and any one of the nets used is of mesh size equal to or greater than 90 mm, unless the percentage composition of the catches retained on board is in compliance with the relevant conditions laid down in Annex X(B); or (iii)the catches are taken in Region 3 except for ICES Division IXa east of 7o 23′ 48″ W and any one of the nets used is of mesh size equal to or greater than 70 mm, unless the percentage composition of the catches retained on board is in compliance with the relevant conditions laid down in Annex XI(A); or (iv)the catches are taken in ICES Division IXa east of 7o 23′ 48″ W and any one of the nets used is of mesh size equal to or greater than 55 mm, unless the percentage composition of the catches retained on board is in compliance with the relevant conditions laid down in Annex XI(B); (b)For each fishing voyage, during which only towed nets of one range of mesh size are used, landings shall be prohibited whenever the catch taken in each of the regions or geographical areas mentioned in Annexes I to V, and retained on board, does not comply with the corresponding conditions laid down in the relevant annex. 5. (a)The percentage of target species and of other species shall be obtained by aggregating all quantities retained on board, or transshipped, of target species and other species as set out in Annexes I to V. (b)However, detailed rules for obtaining the percentage of target species and of other species retained on board when these have been taken by a net or nets towed simultaneously by more than one fishing vessel, shall be drawn up in accordance with the procedure laid down in Article 48. 6. Before 31 May 2001, Member States will report to the Commission on the application of the conditions laid down in this Article, Article 15 and relevant Annexes. On the basis of these reports, the Commission shall submit appropriate proposals. The Council shall decide, on the basis of any such proposal, before 31 October 2001.

Article 5 1. The percentages referred to in Annexes I to V, X and XI shall be calculated as the proportion by live weight of all marine organisms on board after sorting or on landing. 2. However, when calculating the percentages referred to in paragraph 1 for a fishing vessel from which quantities of marine organisms have been transhipped, these quantities shall be taken into account. 3. Masters of fishing vessels who do not complete a logbook in accordance with the provisions of Article 6 of Regulation (EEC) No 2847/93 shall not tranship marine organisms to any other vessel, or receive transhipments of marine organisms from any other vessel. 4. The percentages referred to in paragraph 1 may be calculated on the basis of one or more representative samples. 5. Notwithstanding paragraph 1, in the case of catches of sand eel retained on board and caught with nets having mesh sizes smaller than 16 millimetres, the percentage may be calculated before sorting. 6. For the purpose of this Article, the equivalent weight of whole Norway lobster shall be obtained by multiplying the weight of Norway lobster tails by three.

Article 6 1. (a)The carrying on board or the use of any demersal trawl, Danish seine or similar towed net having more than 100 meshes in any circumference of the cod-end stricto sensu, excluding the joinings and selvedges shall be prohibited. This provision shall apply to demersal trawls, Danish seines or similar towed nets of which the mesh size lies within the range 90 to 119 millimetres. (b)The first subparagraph shall not apply to beam trawls. 2. Within any single cod-end stricto sensu, the number of meshes around any circumference of the cod-end must not increase from the front end to the rear end. This provision shall apply to all towed nets of which the mesh size is equal to, or greater than, 55 millimetres. 3. The number of meshes, excluding those in the selvedges, at any point on any circumference of any extension or lengthening piece shall not be less than the maximum number of meshes on the circumference of the front-end of the cod-end stricto sensu excluding meshes in the selvedges. This provision shall apply to all towed nets of which the mesh size is equal to, or greater than, 55 millimetres.

Article 7 1. (a)Square-meshed panels of a mesh size of at least 80 millimetres may be inserted into any towed net. (b)Alternatively, any demersal trawl, Danish seine or similar towed net of which the mesh size is equal to, or greater than, 100 millimetres may be equipped with panels authorised in accordance with Council Regulation (EEC) No 1866/86 of 12 June 1986 laying down certain technical measures for the conservation of fishery resources in the waters of the Baltic Sea, the Belts and the SoundOJ L 162, 18.6.1986, p. 1. Regulation as last amended by Regulation (EC) No 1821/96 (OJ L 241, 21.9.1996, p. 8).. 2. Any square-meshed panel: (a)shall be placed in the top half or top sheet of a net in front of any extension piece or at any point between the front of any extension piece and the posterior of the cod-end; (b)shall not be obstructed in any way by either internal or external attachments; (c)shall be at least three metres in length except when incorporated into nets towed by vessels of less than 112 kilowatts, when it must be of at least two metres in length; (d)shall be constructed of knotless netting or of netting constructed with non-slip knots, and shall be inserted in such a way that the meshes remain fully open at all times while fishing; (e)shall be constructed so that the number of meshes in the anterior row of meshes of the panel is equal to or greater than the number of meshes in the posterior row of meshes in the panel. 3. In any net in which a square-meshed panel is inserted in an untapered portion of the net, there shall be at most five open diamond meshes between each panel side and the adjacent selvedges of the net. In any net in which a square-meshed panel is inserted, wholly or partially, into a tapered portion of the net there shall be at most five open diamond meshes between the posterior row of meshes in the square-meshed panel and the adjacent selvedges of the net. 4. Notwithstanding paragraph 1(a), any demersal trawl, Danish seine or similar towed net of which the mesh size lies in the range 70 to 79 millimetres shall be equipped with a square-meshed panel having a mesh size equal to, or greater than, 80 millimetres. 5. Notwithstanding paragraph 1(a), the retention on board of any quantity of crustaceans of the genus Pandalus caught with any demersal towed net having a mesh size lying in the range 32 to 54 millimetres shall be prohibited, unless the net is equipped with a square-meshed panel or window having a mesh size equal to, or greater than, 70 millimetresor with a sorting grid whose use is established under the conditions laid down in Article 46. 6. The conditions of paragraphs 4 and 5 shall apply only within Regions 1 and 2. 7. Measurements of the mesh size of any square-meshed netting inserted into any part of a net shall not be taken into consideration when assessing the mesh size of a towed net.

Article 8 1. The carrying on board or the use of any towed nets constructed wholly or in part in the cod-end of single twine netting materials having a twine thickness of more than eight millimetres shall be prohibited. 2. The carrying on board or the use of any towed nets constructed wholly or in part in the cod-end of netting materials consisting of multiple twine shall be prohibited, unless the multiple twines are of approximately equal thickness and unless the sum of the thicknesses of the multiple twines on any side of any mesh is no more than 12 millimetres. 3. Paragraphs 1 and 2 shall not apply to pelagic trawls.

Article 9 1. The carrying on board or the use of any towed net the cod-end of which is constructed wholly or in part of any type of netting material made of meshes other than square mesh or diamond mesh shall be prohibited. 2. Paragraph 1 shall not apply to any towed net the cod-end of which has a mesh size of 31 millimetres or less.

Article 10 Dredges are exempted from the provisions of Article 4. However, it shall be prohibited during any voyage when dredges are carried on board, (a)to tranship marine organisms and (b)to retain on board or land any quantity of marine organisms unless at least 95 % by weight thereof consists of bivalve molluscs.

CHAPTER II PROVISIONS FOR FIXED GEARS

Article 11 1. For each of the regions or geographical areas mentioned in Annexes VI and VII, and depending where applicable on the time-period, the use or keeping on board of any bottom set gillnet, entangling net or trammel net shall be prohibited, unless: (a)the catch taken with that net and retained on board includes a percentage of target species no less than 70 %; and (b) in the case of bottom set gillnets and entangling nets, its mesh size corresponds to one of the categories set out in the relevant Annex, in the case of trammel nets, its mesh size in that part of the net having the smallest meshes corresponds to one of the categories set out in the relevant Annex. This derogation shall apply without prejudice to Article 34b(2)(c). 2. The minimum percentage of target species may be obtained by aggregating the quantities of all the target species caught.

Article 11a In Region 9, the minimum mesh size for bottom set gillnets, when used to catch turbot, shall be 400 millimetres.

Article 12 1. The percentage referred to in Article 11(1) shall be calculated as the proportion by live weight of all marine organisms on board after sorting or on landing. 2. The percentage referred to in paragraph 1 may be calculated on the basis of one or more representative samples.

Article 13 Articles 11 and 12 shall not apply to catches of salmonids, lampreys or hagfish.

CHAPTER III GENERAL PROVISIONS ON NETS AND CONDITIONS FOR THEIR USE

Article 14 Sorting shall be carried out immediately after catches have been removed from the net or nets.

Article 15 1. Quantities of marine organisms caught in excess of permitted percentages specified in Annexes I to VII, X and XI may not be landed but shall be returned to the sea prior to each landing. 2. At all times during a fishing voyage, and following sorting of the catch, the percentage of target species as defined in Annexes I to VIl retained on board shall be at least half of the minimum percentages of the target species referred to in the said Annexes. 3. Masters of fishing vessels who are required to complete a logbook shall ensure that after the first 24 hours of a fishing voyage has expired, the minimum percentage of target species as set out in Annexes I to VII, X and XI shall be met at the time of each completion of the logbook, in accordance with conditions laid out in Article 6 of Regulation (EEC) No 2847/93. 4. Whenever, during a fishing voyage, a vessel newly enters any of the regions or geographical areas mentioned in Annexes I to V, the minimum percentage of target species, as set out in Annexes I to VII, X and XI, caught and retained on board from the region or geographical area previously fished during this voyage shall be met within two hours.

Article 16 No device shall be used by means of which the mesh in any part of the fishing net is obstructed or otherwise effectively diminished. This provision shall not exclude the use of certain devices of which a list and technical descriptions shall be drawn up in accordance with the procedure referred to in Article 48.

TITLE III MINIMUM SIZE OF MARINE ORGANISMS

Article 17 A marine organism is undersized if its dimensions are smaller than the minimum dimensions specified in Annex XII and Annex XIIa for the relevant species and the relevant geographical area.

Article 18 1. The measurement of the size of a marine organism shall take place in accordance with the provisions laid down in Annex XIII. 2. Where more than one method of measuring the size of a marine organism is provided for, the organism is considered to be of the minimum size if the application of any one of these methods results in a size equal to, or greater than, the corresponding minimum size. 3. Lobsters, crawfish, and bivalve and gastropod molluscs belonging to any such species for which a minimum size is set in Annex XII may only be retained on board whole and may only be landed whole. 4. (a)For catches of edible crabs made by pots or creels, a maximum of 1 % by weight of the total catch of edible crabs or parts thereof retained on board during any fishing voyage or landed at the end of any fishing voyage may consist of detached crab claws. (b)For catches of edible crabs made by any fishing gear other than pots or creels, a maximum of 75 kg of detached crab claws may be retained on board at any moment in time during a fishing voyage or may be landed at the end of any fishing voyage.

Article 19 1. Undersized marine organisms shall not be retained on board or be transhipped, landed, transported, stored, sold, displayed or offered for sale, but shall be returned immediately to the sea. 2. Paragraph 1 shall not apply to: (a)sardine, anchovy, herring, horse mackerel and mackerel, within a limit of 10 % by live weight of the total catches retained on board of each of these species. The percentage of undersized sardine, anchovy, herring, horse mackerel or mackerel shall be calculated as the proportion by live weight of all marine organisms on board after sorting or on landing. The percentage may be calculated on the basis of one or more representative samples. The limit of 10 % shall not be exceeded during transhipment, landing, transportation, storage, display or sale; (b)marine organisms other than those defined in Annexes I to V as target species for the mesh size categories smaller than 16 millimetres or than 16 to 31 millimetres, and caught with towed gear of a mesh size less than 32 millimetres, provided that said organisms are not sorted and are not sold, displayed or offered for sale for human consumption. 3. However, undersized sardine, anchovy, horse mackerel or mackerel caught for use as live bait may be retained on board, provided they are retained alive. 4. Paragraphs 2 and 3 shall not apply in Region 9.

TITLE IIIa MEASURES TO REDUCE DISCARDING

Article 19a Prohibition of highgrading 1. Within Regions 1, 2, 3 and 4 the discarding, during fishing operations, of species subject to quota which can be legally landed shall be prohibited. 2. The provisions referred to in paragraph 1 are without prejudice to the obligations set out in this Regulation or in any other Union legal acts in the field of fisheries.

Article 19b Moving-on provisions and prohibition on slipping 1. Within Regions 1, 2, 3 and 4, where the quantity of undersized mackerel, herring or horse mackerel exceeds 10 % of the total quantity of the catches in any one haul, the vessel shall move fishing grounds. 2. Within Regions 1, 2, 3 and 4 it is prohibited to release mackerel, herring or horse mackerel before the net is fully taken on board a fishing vessel resulting in the loss of dead or dying fish.

TITLE IV SPECIAL PROVISIONS RELATING TO FISHING FOR CERTAIN MARINE ORGANISMS

Article 20 Restrictions on fishing for herring 1. The retention on board of herring which are caught within the geographical areas and during the periods mentioned below shall be prohibited: (a)from 1 January to 30 April, within the geographical area situated to the north-east of a line drawn between Mull of Kintyre and Corsewall Point; (b)from 1 July to 31 October, within the geographical area bounded by the following coordinates: the west coast of Denmark at latitude 55o 30′ N, latitude 55o 30′ N, longitude 7o 00′ E, latitude 57o 00′ N, longitude 7o 00′ E, the west coast of Denmark at latitude 57o 00′ N; (c)from 15 August to 15 September, within the zone extending from six to 12 miles off the east coast of the United Kingdom as measured from the baselines between latitudes 55o 30′ N and 55o 45′ N; (d)from 15 August to 30 September, within the geographical area bounded by a line joining the following points: the Butt of Lewis, Cape Wrath, latitude 58o 55′ N, longitude 5o 00′ W, latitude 58o 55′ N, longitude 7o 10′ W, latitude 58o 20′ N, longitude 8o 20′ W, latitude 57o 40′ N, longitude 8o 20′ W, the west coast of North Uist at latitude 57o 40′ N, then along the north coast of the island as far as latitude 57o 40′ 36″ N, longitude 7o 20′ 39″ W, latitude 57o 50′ 3″ N, longitude 7o 8′ 6″ W, north-east along the west coast of Lewis as far as the point of departure (Butt of Lewis); (e)from 15 August to 30 September, within the zone extending from six to 12 miles off the east coast of the United Kingdom as measured from the baselines between latitudes 54o 10′ N and 54o 45′ N; (f) (i)from 21 September to 15 November, within the part of ICES Division VIIa bounded by the coast of the Isle of Man and straight lines drawn consecutively between the following coordinates: latitude 54o20′00″ N, longitude 04o25′05″ W and latitude 54o20′00″ N, longitude 03o57′02″ W, latitude 54o20′00″ N, longitude 03o57′02″ W and latitude 54o17′05″ N, longitude 03o56′08″ W, latitude 54o17′05″ N, longitude 03o56′08″ W and latitude 54o14′06″ N, longitude 03o57′05″ W, latitude 54o14′06″ N, longitude 03o57′05″ W and latitude 54o00′00″ N, longitude 04o07′05″ W, latitude 54o00′00″ N, longitude 04o07′05″ W and latitude 53o51′05″ N, longitude 04o27′08″ W, latitude 53o51′05″ N, longitude 04o27′08″ W and latitude 53o48′00″ N, longitude 04o50′00″ W, latitude 53o48′05″ N, longitude 04o50′00″ W and latitude 54o04′05″ N, longitude 04o50′00″ W; (ii)from 21 September to 31 December, within the part of ICES Division VIIa bounded by the following coordinates: the east coast of Northern Ireland at latitude 54o15′ N, latitude 54o 15′ N, longitude 5o15′ W, latitude 53o50′ N, longitude 5o50′ W, the east coast of Ireland at latitude 53o50′ N; (g)throughout the year within ICES Division VIIa, in the geographical area between the west coasts of Scotland, England and Wales, and a line drawn 12 miles from the baselines of the coasts bounded to the south by latitude 53o 20′ N and to the north-west by a line drawn between the Mull of Galloway (Scotland) and the Point of Ayre (Isle of Man); (h)throughout the year within Logan Bay, defined as the waters east of a line drawn from the Mull of Logan situated at latitude 54o 44′ N and longitude 4o 59′ W, to Laggantalluch Head, situated at latitude 54o 41′ N and longitude 4o 58′ W; (i)in 1997, and every third year thereafter, from the second Friday in January, for a period of 16 consecutive days within the area bounded by the following coordinates: the south-east coast of Ireland at latitude 52o 00′ N, latitude 52o 00′ N, longitude 6o 00′ W, latitude 52o 30′ N, longitude 6o 00′ W, the south-east coast of Ireland at latitude 52o 30′; (j)in 1997, and every third year thereafter from the first Friday in November for a period of 16 consecutive days within the area bounded by the following coordinates: the south coast of Ireland at longitude 9o 00′ W, latitude 51o 15′ N, longitude 9o 00′ W, latitude 51o 15′ N, longitude 11o 00′ W, latitude 52o 30′ N, longitude 11o 00′ W, the west coast of Ireland at latitude 52o 30′ N; (k)in 1998, and every third year thereafter, from the first Friday in November for a period of 16 consecutive days within the area bounded by the following coordinates: the south coast of Ireland at longitude 9o 00′ W, latitude 51o 15′ N, longitude 9o 00′ W, latitude 51o 15′ N, longitude 7o 30′ W, the south coast of Ireland at latitude 52o 00′ N. 2. However, vessels may retain on board quantities of herring from any of the areas described, provided they do not exceed 5 % of the total live weight of the marine organisms on board which have been caught in each separate area during one of the periods specified. 3. Notwithstanding paragraph 1, points (f)(ii) and (h), vessels with a length not exceeding 12,2 metres based in ports situated on the east coast of Ireland and Northern Ireland between latitudes 53o 00′ N and 55o 00′ N may retain on board quantities of herring from the areas set out in paragraph 1, points (f)(ii) and (h). The only method of fishing authorised shall be drift-netting with nets of a mesh size equal to, or greater than, 54 millimetres.

Article 20a Restrictions on fishing for herring in Union waters of ICES division IIa It shall be prohibited to land or retain on board herring caught in Union waters of ICES division IIa in the periods from 1 January to 28 February and from 16 May to 31 December.

Article 21 Restrictions on fishing for sprat to protect herring 1. The retention on board of sprat which are caught within the geographical areas and during the periods mentioned below shall be prohibited: (a)from 1 January to 31 March, and from 1 October to 31 December, within ICES statistical area 39E8. For the purpose of this Regulation, this ICES area shall be the area bounded by a line due east from the United Kingdom east coast along latitude 55o 00′ N to a point at longitude 1o 00′ W, from there due north to a point at latitude 55o 30′ N and from there due west to the United Kingdom coast; (b)from 1 January to 31 March, and from 1 October to 31 December, within the inner waters of the Moray Firth west of longitude 3o 30′ W, and in the inner waters of the Firth of Forth west of longitude 3o 00′ W, (c)from 1 July to 31 October, within the geographical area bounded by the following coordinates: the west coast of Denmark at latitude 55o 30′ N, latitude 55o 30′ N, longitude 7o 00′ E, latitude 57o 00′ N, longitude 7o 00′ E, the west coast of Denmark at latitude 57o 00′ N. 2. However, vessels may retain on board quantities of sprat from any of the areas described, provided they do not exceed 5 % of the total live weight of the marine organisms on board which have been caught in each separate area during any of the periods specified.

Article 22 Restrictions on fishing for mackerel 1. the retention on board of mackerel which are caught within the geographical area bounded by the following coordinates shall be prohibited: a point on the south coast of the United Kingdom at longitude 2o 00′ W, latitude 49o 30′ N, longitude 2o 00′ W, latitude 49o 30′ N, longitude 7o 00′ W, latitude 52o 00′ N, longitude 7o 00′ W, a point on the west coast of the United Kingdom at latitude 52o 00′ N,except where the weight of the mackerel does not exceed 15 % by live weight of the total quantities of mackerel and other marine organisms on board which have been caught in this area. 2. Paragraph 1 shall not apply: (a)to vessels fishing exclusively with gill nets and/or hand lines; (b)to vessels fishing with demersal trawls, Danish seines or other similar towed nets, provided that they have on board a minimum of 75 % by live weight of marine organisms with the exception of anchovy, herring, horse mackerel, mackerel, pelagic cephalopods and sardine, calculated as a percentage of the total live weight of all the marine organisms on board; (c)to vessels which are not equipped for fishing and to which mackerel are being transhipped. 3. All mackerel which are on board shall be deemed to have been caught within the area provided for by paragraph 1, except those which have been declared to be on board before the vessel enters that area, under the procedure described in the following subparagraphs. The master of a vessel intending to enter that area in order to fish, and holding mackerel on board, shall notify the control authority of the Member state in whose zone he intends to fish of his estimated time and place of arrival in this area no more than 36 hours and no less than 24 hours before the vessel enters that area. On entering the area, he shall notify the competent control authority of the quantities of mackerel which he has on board and which are entered in the log-book. The master may be required to submit his log-book and the catches on board for verification at a time and place to be determined by the competent control authority. The time shall be no later than six hours after receipt by the control authority of the message notifying the quantities of mackerel on board and the place shall be as near as possible to the point of entry into the area. The master of the fishing vessel who intends to enter the area for the purpose of having mackerel transhipped to his vessel shall notify the control authority of the Member State in whose zone transhipment will take place, or the intended time and place of transhipment no more than 36 hours and no less than 24 hours before transhipment begins. Immediately on completion of transhipment, the master shall inform the competent control authority of the quantities of mackerel which have been transhipped to that vessel. The competent control authorities are: for France:Mimer, telex: Paris 25 08 23, for Ireland:Department of Marine, telex: Dublin 91798 MRNE, for the United Kingdom:Ministry of Agriculture, Fisheries and Food, telex: London 21274.

Article 23 Restrictions on fishing for anchovy 1. The retention on board of anchovy caught using pelagic trawls in ICES Division VIIIc or the fishing for anchovy with pelagic trawls in this Division shall be prohibited. 2. Within the Division referred to in paragraph 1, the simultaneous carrying on board of pelagic trawls and purse seines shall be prohibited.

Article 24 Restrictions on fishing for tuna 1. The retention on board of any quantity of skipjack, bigeye or yellowfin tuna which are caught using purse seines in waters under the sovereignty or jurisdiction of Portugal in ICES sub-area X north of 36o 30′ N or in CECAF areas north of 31o N and east of 17o 30′ W, or the fishing for the said species in the said areas with the said gears shall be prohibited. 2. The retention on board of tuna which are caught using drift-nets in waters under the sovereignty or jurisdiction of Spain or Portugal in ICES sub-areas VIII, IX and X, or in CECAF areas around the Canary Islands and Madeira, or the fishing for the said species in the said areas with the said gears shall be prohibited.

Article 25 Restrictions on fishing for shrimps to protect flatfish 1. The retention on board of any quantity of common shrimps and Aesop shrimps caught with demersal towed nets having any mesh size between 16 and 31 millimetres shall be prohibited, unless the vessel has installed on board a functioning device designed to separate flatfish from common shrimps and Aesop shrimps following capture. 2. At the latest on 1 July 2002, a separator trawl or a trawl with a sorting grid shall be used to catch common shrimps and Aesop shrimps in conformity with detailed rules which Member States shall establish in accordance with Article 46. Such rules may be applicable only to nets towed by fishing vessels. 3. However, quantities of common shrimp or Aesop shrimp may be retained on board fishing vessels that do not comply with the provisions laid down in paragraphs 1 and 2, provided these quantities do not exceed 5 % of the total live weight of the marine organisms on board.

Article 26 Restrictions on fishing for salmon and sea trout 1. Salmon and sea trout shall not be retained on board or be transhipped, landed, transported, stored, sold, displayed or offered for sale, but shall be returned immediately to the sea when taken: within the waters situated outside the six-mile limit measured from Member States' baselines in regions 1, 2, 3 and 4, by way of derogation from Article 2(1), outside the waters under the sovereignty or jurisdiction of the Member States in regions 1, 2, 3, and 4, except in the waters under the jurisdiction of Greenland and the Faroe Islands, when fishing with any towed net. 2. Paragraph 1 shall not apply to salmon and sea trout taken within the Skagerrak and Kattegat.

Article 27 Restrictions on fishing for Norway pout to protect other roundfish 1. The retention on board of Norway pout which are caught with any towed gear in the area which is bounded by a line joining the following points shall be prohibited: a point at 56o N on the east coast of the United Kingdom as far as 2o E, the running north to 58o N, west to 0o 30′ W, north to 59o 15′ N, east to 1o E, north to 60o N, west to longitude 0o 00′; from there north to 60o 30′ N, west to the coast of the Shetland Isles, then west from 60o N on the west coast of the Shetlands to 3o W, south to 58o 30′ N, and finally west to the coast of the United Kingdom. 2. However, vessels may retain on board quantities of Norway pout from the area and caught with the gear described in paragraph 1, provided they do not exceed 5 % of the total weight of the marine organisms on board which have been caught in the said area with the said gear.

Article 28 Restrictions on fishing for hake 1. Fishing with any trawl, Danish seine or similar towed net, in the geographical areas and during the periods mentioned below, shall be prohibited: (a)from 1 October to 31 January of the following year, within the geographical area bounded by a line sequentially joining the following coordinates: latitude 43o46,5′ N, longitude 7o54,4′ W, latitude 44o1,5′ N, longitude 7o54,4′ W, latitude 43o25′ N, longitude 9o12′ W, latitude 43o10′ N, longitude 9o12′ W; (b)from 1 October to 31 December, within the geographical area bounded by a line joining the following coordinates: the point on the west coast of Spain called Cabo Corrubedo (latitude 42o 35′ N, longitude 9o 05′ W), latitude 42o 35′ N, longitude 9o 25′ W, latitude 43o 00′ N, longitude 9o 30′ W, the point on the west coast of Spain at latitude 43o 00′ N; (c)from 1 December to the last day of February in the following year, within the geographical area bounded by a line joining the following coordinates: a point on the west coast of Portugal at latitude 37o 50′ N, latitude 37o 50′ N, longitude 9o 08′ W, latitude 37o 00′ N, longitude 9o 07′ W, a point on the west coast of Portugal at latitude 37o 00′ N. 2. Within the zones and during the periods referred to in paragraph 1, the carrying on board of any trawl, Danish seine or similar towed net shall be prohibited, unless such gears are lashed and stowed in accordance with the provisions laid down in Article 20(1) of Regulation (EEC) No 2847/93.

Article 29 Conditions applicable in a major plaice nursery area 1. Vessels exceeding eight metres length overall shall be prohibited from using any demersal trawl, Danish seine or similar towed gear inside the following geographical areas: (a)the area within 12 miles of the coasts of France, north of latitude 51o 00′ N, Belgium, and the Netherlands up to latitude 53o 00′ N, measured from the baselines; (b)the area bounded by a line joining the following coordinates: a point on the west coast of Denmark at latitude 57o 00′ N, latitude 57o 00′ N, longitude 7o 15′ E, latitude 55o 00′ N, longitude 7o 15′ E, latitude 55o 00′ N, longitude 7o 00′ E, latitude 54o 30′ N, longitude 7o 00′ E, latitude 54o 30′ N, longitude 7o 30′ E, latitude 54o 00′ N, longitude 7o 30′ E, latitude 54o 00′ N, longitude 6o 00′ E, latitude 53o 50′ N, longitude 6o 00′ E, latitude 53o 50′ N, longitude 5o 00′ E, latitude 53o 30′ N, longitude 5o 00′ E, latitude 53o 30′ N, longitude 4o 15′ E, latitude 53o 00′ N, longitude 4o 15′ E, a point on the coast of the Netherlands at latitude 53o 00′ N; (c)the area within 12 miles of the west coast of Denmark from latitude 57o 00′ N as far north as the Hirtshals Lighthouse, measured from the baselines. 2. (a)However, vessels to which a special fishing permit has been issued in accordance with Article 7(3) of Regulation (EC) No 1627/94 shall be authorised to fish in the areas referred to in paragraph 1 using beam trawls. The use of any beam trawl of which the beam length, or of any beam trawls of which the aggregate beam length, measured as the sum of the length of each beam, is greater than nine metres, or can be extended to a length greater than nine metres, shall be prohibited, except when operating with gear having a mesh size between 16 and 31 millimetres. The length of a beam shall be measured between its extremities including all attachments thereto. (b)Notwithstanding Article 1(2) of Regulation (EC) No 1627/94, special fishing permits for the purposes indicated in (a) may be issued for vessels exceeding eight metres length overall. (c)Vessels to which a special fishing permit as referred to in (a) and (b) has been issued shall comply with the following criteria: they must be included in a list to be provided to the Commission by each Member State such that the total engine power of the vessels within each list does not exceed the total engine power in evidence for each Member State at 1 January 1998, their engine power does not exceed 221 kilowatts (kW) at any time and, in the case of derated engines did not exceed 300 kW before derating. (d)Any individual vessel on the list may be replaced by another vessel or vessels, provided that: no replacement will lead to an increase for each Member State in its total engine power indicated in the first indent of (c), the engine power of any replacement vessel does not exceed 221 kW at any time, the engine of any replacement vessel is not derated, and the length overall of any replacement vessel does not exceed 24 metres. (e)An engine of any individual vessel included in the list for any Member State may be replaced, provided that: the replacement of an engine does not lead to the vessel's engine power exceeding 221 kW at any time, the replacement engine is not derated, and the power of the replacement engine is not such that replacement will lead to an increase in the total engine power as indicated in the first indent of (c) for that Member State. (f)Fishing vessels which do not comply with the criteria specified in this paragraph shall have their special fishing permit withdrawn. 3. Notwithstanding paragraph 2(a), vessels holding a special fishing permit and whose primary activity is fishing for common shrimp, shall be permitted to use beam trawls of which the aggregate beam length, measured as the sum of the length of each beam, is greater than nine metres when operating with gear having a mesh size between 80 and 99 millimetres, provided that an additional special fishing permit to this effect has been issued to these vessels. This additional special fishing permit shall be annually reviewed. Any vessel or vessels to which such an additional special fishing permit has been issued may be replaced by another vessel, provided that: the replacement vessel does not exceed 70 GRT and does not exceed an overall length of 20 metres, or the capacity of the replacement vessel does not exceed 180 kW and that the replacement vessel does not exceed an overall length of 20 metres. Fishing vessels which cease to comply with the criteria specified in this paragraph shall have their additional special fishing permit permanently withdrawn. 4. (a)By way of derogation from paragraph 1: vessels whose engine power does not exceed 221 kW at any time and, in the case of derated engines did not exceed 300 kW before derating, shall be authorised to fish in the areas referred to in that paragraph using demersal otter trawls or Danish seine, paired vessels whose combined engine power does not exceed 221 kW at any time and, in the case of derated engines did not exceed 300 kW before derating, shall be authorised to fish in said areas using demersal pair trawls. (b)However, vessels whose engine power exceeds 221 kW shall be permitted to use demersal otter trawls or Danish seine, or paired vessels whose combined engine power exceeds 221 kW shall be permitted to use demersal pair trawls, provided that: (i) the catch of sand eel and/or sprat retained on board and caught in the said areas constitutes at least 90 % of the total live weight of the marine organisms on board and caught in the said areas, and the quantities of plaice and/or sole retained on board and caught in the said areas do not exceed 2 % of the total live weight of the marine organisms on board and caught in the said areas;or (ii) in the case of demersal otter trawls or demersal pair trawls, the mesh size used is at least 100 millimetres, and the quantities of plaice and/or sole retained on board and caught in the said areas do not exceed 5 % of the total weight of the marine organisms on board and caught in the said areas;or (iii) the mesh size used is at least 80 millimetres, and the use of such mesh sizes is restricted to an area within 12 miles of the coast of France north of latitude 51o 00′ N, and the quantities of plaice and/or sole retained on board and caught in the said areas, do not exceed 5 % of the total live weight of the marine organisms on board and caught in the said areas;or (iv)in the case of Danish seine, the mesh size used is at least 100 millimetres. 5. Within areas where beam trawls, otter trawls, bottom pair trawls or Danish seine may not be used, the carrying on board of such nets shall be prohibited, unless they are lashed and stowed in accordance with the provisions laid down in Article 20(1) of Regulation (EEC) No 2847/93. 6. Detailed rules for the implementation of this Article shall be drawn up in accordance with the procedure laid down in Article 48.

Article 29a Closure of an area for sand eel fisheries in ICES sub-area IV 1. It shall be prohibited to land or retain on board sand eels caught within the geographical area bounded by the east coast of England and Scotland, and enclosed by sequentially joining with rhumb lines the following coordinates, which shall be measured according to the WGS84 system: the east coast of England at latitude 55°30′ N, latitude 55°30′ N, longitude 01°00′ W, latitude 58°00′ N, longitude 01°00′ W, latitude 58°00′ N, longitude 02°00′ W, the east coast of Scotland at longitude 02°00′ W. 2. Fisheries for scientific investigation shall be allowed in order to monitor the sand eel stock in the area and the effects of the closure.

Article 29b Restrictions on fishing for Norway lobster 1. During the periods set out below fishing with: (i)bottom trawls or similar towed nets operating in contact with the bottom of the sea, and (ii)creels shall be prohibited in the geographical areas bounded by rhumb lines joining the following positions as measured according to the WGS84 standard: (a)from 1 June to 31 August: latitude 42°23′ N, longitude 08°57′ W latitude 42°00′ N, longitude 08°57′ W latitude 42°00′ N, longitude 09°14′ W latitude 42°04′ N, longitude 09°14′ W latitude 42°09′ N, longitude 09°09′ W latitude 42°12′ N, longitude 09°09′ W latitude 42°23′ N, longitude 09°15′ W latitude 42°23′ N, longitude 08°57′ W; (b)from 1 May to 31 August: latitude 37°45′ N, longitude 09°00′ W latitude 38°10′ N, longitude 09°00′ W latitude 38°10′ N, longitude 09°15′ W latitude 37°45′ N, longitude 09°20′ W. 2. By way of derogation from the prohibition laid down in paragraph 1, fishing with bottom trawls or similar towed nets operating in contact with the bottom of the sea in the geographical areas and during the period set out in paragraph 1(b) shall be authorised provided that the by-catch of Norway lobster does not exceed 2 % of the total weight of the catch. 3. By way of derogation from the prohibition laid down in paragraph 1, fishing with creels that do not catch Norway lobster shall be authorised in the geographical areas and during the periods set out in that paragraph. 4. In the geographical areas and outside the periods referred to in paragraph 1, the by-catch of Norway lobster may not exceed 5 % of the total weight of the catch. 5. In the geographical areas and outside the periods set out in paragraph 1, Member States shall ensure that the fishing effort levels of vessels fishing with bottom trawls or similar towed nets operating in contact with the bottom of the sea do not exceed the levels of fishing effort carried out by the vessels of the Member State concerned during the same periods and in the same geographical areas in 2004. 6. Member States shall communicate to the Commission their measures to fulfil the obligation laid down in paragraph 5. If the Commission finds that the measures of a Member State do not fulfil that obligation, it may propose amendments to those measures. In the absence of agreement on measures between the Commission and the Member State concerned, the Commission may adopt measures in accordance with the procedure referred to in Article 30(2) of Regulation (EC) No 2371/2002OJ L 358, 31.12.2002, p. 59..

Article 29c Rockall Haddock box in ICES sub-area VI 1. All fishing of Rockall haddock, except with longlines, shall be prohibited in the areas enclosed by sequentially joining with rhumb lines the following coordinates, which shall be measured according to the WGS84 system: 57°00′ N, 15°00′ W 57°00′ N, 14°00′ W 56°30′ N, 14°00′ W 56°30′ N, 15°00′ W 57°00′ N, 15°00′ W.

Article 29d Restrictions on fishing for cod, haddock and whiting in ICES sub-area VI 1. It shall be prohibited to conduct any fishing activity for cod, haddock and whiting within that part of ICES division VIa that lies to the east or to the south of those rhumb lines which sequentially join the following coordinates, which shall be measured according to the WGS84 system: 54°30′ N, 10°35′ W 55°20′ N, 09°50′ W 55°30′ N, 09°20′ W 56°40′ N, 08°55′ W 57°00′ N, 09°00′ W 57°20′ N, 09°20′ W 57°50′ N, 09°20′ W 58°10′ N, 09°00′ W 58°40′ N, 07°40′ W 59°00′ N, 07°30′ W 59°20′ N, 06°30′ W 59°40′ N, 06°05′ W 59°40′ N, 05°30′ W 60°00′ N, 04°50′ W 60°15′ N, 04°00′ W. 2. Any fishing vessel present within the area referred to in paragraph 1 of this Article shall ensure that any fishing gears carried on board are lashed and stowed in accordance with Article 47 of Council Regulation (EC) No 1224/2009 of 20 November 2009 establishing a Community control system for ensuring compliance with the rules of the common fisheries policyOJ L 343, 22.12.2009, p. 1.. 3. By way of derogation from paragraph 1, it shall be permitted to conduct fishing activities within the area referred to in that paragraph using inshore static nets fixed with stakes, scallop dredges, mussel dredges, handlines, mechanised jigging, draft nets and beach seines, pots and creels, provided that: (a)no fishing gears other than inshore static nets fixed with stakes, scallop dredges, mussel dredges, handlines, mechanised jigging, draft nets and beach seines, pots and creels are carried on board or deployed; and (b)no fish other than mackerel, pollack, saithe and salmon, or shellfish other than molluscs and crustaceans are retained on board, landed or brought ashore. 4. By way of derogation from paragraph 1, it shall be permitted to conduct fishing activities within the area referred to in that paragraph using nets with a mesh size of less than 55 millimetres, provided that: (a)no net of mesh size greater than or equal to 55 millimetres is carried on board; and (b)no fish other than herring, mackerel, pilchard/sardines, sardinelles, horse mackerel, sprat, blue whiting, boarfish and argentines are retained on board. 5. By way of derogation from paragraph 1, it shall be permitted to conduct fishing activities within the area referred to in that paragraph using gillnets of mesh size greater than 120 millimetres, provided that: (a)they are only deployed in the area south of 59° N; (b)the maximum length of gillnet deployed is 20 km per vessel; (c)the maximum soak time is 24 hours; and (d)no more than 5 % of the catch is made up of whiting and cod. 6. By way of derogation from paragraph 1, it shall be permitted to conduct fishing activities within the area referred to in that paragraph using gillnets with a mesh size that is greater than 90 millimetres, provided that: (a)they are only deployed within 3 nautical miles of the coastline and for a maximum of 10 days per calendar month; (b)the maximum length of gillnet deployed is 1000 metres; (c)the maximum soak time is 24 hours; and (d)at least 70 % of the catch is made up of lesser spotted dogfish. 7. By way of derogation from paragraph 1, it shall be permitted to fish for Norway lobster within the area set out in that paragraph, provided that: (a)the fishing gear used incorporates a sorting grid in accordance with points 2 to 5 of Annex XIVa, or a square-mesh panel as described in Annex XIVc, or is another gear with equivalent high selectivity; (b)the fishing gear is constructed with a minimum mesh size of 80 millimetres; (c)at least 30 % of the retained catch by weight is Norway lobster. The Commission shall, on the basis of a favourable opinion by STECF, adopt implementing acts, determining which gears are to be considered to have equivalent high selectivity for the purpose of point (a). 8. Paragraph 7 shall not apply within the area enclosed by sequentially joining with rhumb lines the following coordinates, which shall be measured according to the WGS84 system: 59°05′ N, 06°45′ W 59°30′ N, 06°00′ W 59°40′ N, 05°00′ W 60°00′ N, 04°00′ W 59°30′ N, 04°00′ W 59°05′ N, 06°45′ W. 9. By way of derogation from paragraph 1, it shall be permitted to fish with trawls, demersal seines or similar gears within the area set out in that paragraph, provided that: (a)all nets on board the vessel are constructed with a minimum mesh size of 120 millimetres for vessels with an overall length of more than 15 metres and of 110 millimetres for all other vessels; (b)where the catch retained on board includes less than 90 % saithe the fishing gear used incorporates a square mesh panel as described in Annex XIVc; and (c)where the overall length of the vessel is less than or equal to 15 metres, regardless of the quantity of saithe retained on board, the fishing gear used incorporates a square-mesh panel as described in Annex XIVd. 10. No later than 1 January 2015 and no later than every two years thereafter, the Commission shall, in the light of scientific advice by STECF, assess the characteristics of gears specified in paragraph 9 and, where appropriate, submit to the European Parliament and to the Council a proposal for amendment of paragraph 9. 11. Paragraph 9 shall not apply within the area enclosed by sequentially joining with rhumb lines the following coordinates, which shall be measured according to the WGS84 system: 59°05′ N, 06°45′ W 59°30′ N, 06°00′ W 59°40′ N, 05°00′ W 60°00′ N, 04°00′ W 59°30′ N, 04°00′ W 59°05′ N, 06°45′ W. 12. From 1 January to 31 March, and from 1 October to 31 December each year, it shall be prohibited to conduct any fishing activity using any of the gears specified in Annex I to Council Regulation (EC) No 1342/2008 of 18 December 2008 establishing a long-term plan for cod stocks and the fisheries exploiting those stocksOJ L 348, 24.12.2008, p. 20. in the area specified in ICES area VIa enclosed by sequentially joining with rhumb lines the following coordinates, which shall be measured according to the WGS84 system: 55°25′ N, 07°07′ W 55°25′ N, 07°00′ W 55°18′ N, 06°50′ W 55°17′ N, 06°50′ W 55°17′ N, 06°52′ W 55°25′ N, 07°07′ W. Neither the master of a fishing vessel nor any other person on board shall cause or permit a person on board to attempt to fish for, land, tranship or have on board fish caught in the specified area. 13. Each Member State concerned shall implement an onboard observer programme from 1 January to 31 December each year in order to sample the catches and discards of vessels benefiting from the derogations provided for in paragraphs 5, 6, 7 and 9. The observer programmes shall be carried out without prejudice to the obligations under the respective rules and shall aim to estimate cod, haddock and whiting catches and discards with a precision of at least 20 %. 14. Member States concerned shall produce a report on the total amount of catches and discards made by vessels subject to the observer programme during each calendar year and shall submit it to the Commission no later than 1 February of the following calendar year. 15. No later than 1 January 2015 and no later than every two years thereafter, the Commission shall assess the state of cod, haddock and whiting stocks in the area specified in paragraph 1 in the light of scientific advice by STECF and, where appropriate, submit to the European Parliament and the Council a proposal for the amendment of this Article.

Article 29e Restrictions on fishing for cod in ICES sub-area VII 1. From 1 February until 31 March each year, it shall be prohibited to conduct any fishing activity in ICES sub-area VII in the area which consists of ICES statistical rectangles: 30E4, 31E4, 32E3. This prohibition shall not apply within 6 nautical miles from the baseline. 2. By way of derogation from paragraph 1, it shall be permitted to conduct fishing activities using inshore static nets fixed with stakes, scallop dredges, mussel dredges, draft nets and beach seines, handlines, mechanised jigging, pots and creels within the area and time periods referred to in that paragraph, provided that: (a)no fishing gears other than inshore static nets fixed with stakes, scallop dredges, mussel dredges, draft nets and beach seines, handlines, mechanised jigging, pots and creels are carried on board or deployed; and (b)no fish other than mackerel, pollack, salmon, or shellfish other than molluscs and crustaceans are landed, retained on board or brought ashore. 3. By way of derogation from paragraph 1, it shall be permitted to conduct fishing activities within the area referred to in that paragraph using nets of mesh size less than 55 millimetres, provided that: (a)no net of mesh size greater than or equal to 55 millimetres is carried on board; and (b)no fish other than herring, mackerel, pilchard/sardines, sardinelles, horse mackerel, sprat, blue whiting, boarfish and argentines are retained on board.

Article 29f Special rules for the protection of blue ling 1. From 1 March to 31 May each year it shall be prohibited to retain on board any quantity of blue ling in excess of 6 tonnes per fishing trip in the areas of ICES division VIa enclosed by sequentially joining with rhumb lines the following coordinates, which shall be measured according to the WGS84 system: (a)Edge of Scottish continental shelf 59°58′ N, 07°00′ W 59°55′ N, 06°47′ W 59°51′ N, 06°28′ W 59°45′ N, 06°38′ W 59°27′ N, 06°42′ W 59°22′ N, 06°47′ W 59°15′ N, 07°15′ W 59°07′ N, 07°31′ W 58°52′ N, 07°44′ W 58°44′ N, 08°11′ W 58°43′ N, 08°27′ W 58°28′ N, 09°16′ W 58°15′ N, 09°32′ W 58°15′ N, 09°45′ W 58°30′ N, 09°45′ W 59°30′ N, 07°00′ W 59°58′ N, 07°00′ W; (b)Edge of Rosemary bank 60°00′ N, 11°00′ W 59°00′ N, 11°00′ W 59°00′ N, 09°00′ W 59°30′ N, 09°00′ W 59°30′ N, 10°00′ W 60°00′ N, 10°00′ W 60°00′ N, 11°00′ W Not including the area enclosed by sequentially joining with rhumb lines the following coordinates, which shall be measured according to the WGS84 system: 59°15′ N, 10°24′ W 59°10′ N, 10°22′ W 59°08′ N, 10°07′ W 59°11′ N, 09°59′ W 59°15′ N, 09°58′ W 59°22′ N, 10°02′ W 59°23′ N, 10°11′ W 59°20′ N, 10°19′ W 59°15′ N, 10°24′ W. 2. When entering and exiting the areas referred to in paragraph 1, the master of a fishing vessel shall record the date, time and place of entry and exit in the logbook. 3. In either of the two areas referred to in paragraph 1, if a vessel reaches the 6 tonnes of blue ling: (a)it shall immediately cease fishing and exit the area in which it is present; (b)it may not re-enter either of the areas until its catch has been landed; (c)it may not return to the sea any quantity of blue ling. 4. The observers referred to in Article 8 of Council Regulation (EC) No 2347/2002 of 16 December 2002 establishing specific access requirements and associated conditions applicable to fishing for deep-sea stocksOJ L 351, 28.12.2002, p. 6. who are assigned to fishing vessels present in one of the areas referred to in paragraph 1 shall, in addition to the tasks referred to in paragraph 4 of that Article, for appropriate samples of the catches of blue ling, measure the fish in the samples and determine the stage of sexual maturity of subsampled fish. On the basis of advice from STECF, Member States shall establish detailed protocols for sampling and for the collation of results. 5. From 15 February to 15 April each year, it shall be prohibited to use bottom trawls, longlines and gillnets within an area enclosed by sequentially joining with rhumb lines the following coordinates, which shall be measured according to the WGS84 system: 60°58.76′ N, 27°27.32′ W 60°56.02′ N, 27°31.16′ W 60°59.76′ N, 27°43.48′ W 61°03.00′ N, 27°39.41′ W 60°58.76′ N, 27°27.32′ W.

Article 29g Measures for the redfish fishery in international waters of ICES sub-areas I and II 1. Directed fishing for redfish in the international waters of ICES sub-areas I and II shall only be permitted within the period from 1 July to 31 December each year by vessels which have previously been engaged in the redfish fishery in the NEAFC Regulatory Area, as defined in Article 3(3) of Regulation (EU) No 1236/2010 of the European Parliament and of the Council of 15 December 2010 laying down a scheme of control and enforcement applicable in the area covered by the Convention on future multilateral cooperation in the North-East Atlantic fisheriesOJ L 348, 31.12.2010, p. 17.. 2. Vessels shall limit their by-catches of redfish in other fisheries to a maximum of 1 % of the total catch retained on board. 3. The conversion factor to be applied to the gutted and headed presentation, including the Japanese cut presentation, of redfish caught in this fishery shall be 1,70. 4. By way of derogation from Article 9(1)(b) of Regulation (EU) No 1236/2010, masters of fishing vessels engaged in this fishery shall report their catches on a daily basis. 5. In addition to the provisions of Article 5 of Regulation (EU) No 1236/2010, an authorisation to fish for redfish shall only be valid if the reports transmitted by vessels are in accordance with Article 9(1) of that Regulation and are recorded in accordance with Article 9(3) thereof. 6. Member States shall ensure that scientific information is collected by scientific observers on board vessels flying their flag. As a minimum, the information collected shall include representative data on sex, age and length composition by depths. This information shall be reported to ICES by the competent authorities in the Member States. 7. The Commission shall inform Member States of the date on which the NEAFC Secretariat notifies the NEAFC Contracting Parties that the total allowable catch (TAC) has been fully utilised. Member States shall prohibit directed fishery for redfish by vessels flying their flag from that date.

Article 29h Measures for the redfish fishery in the Irminger Sea and adjacent waters 1. It shall be prohibited to catch redfish in international waters of ICES sub-area V and Union waters of ICES sub-areas XII and XIV. By way of derogation from the first subparagraph, it shall be permitted to catch redfish from 11 May to 31 December in the area enclosed by sequentially joining with rhumb lines the following coordinates, which shall be measured according to the WGS84 system (the "Redfish Conservation Area"): 64°45′ N, 28°30′ W 62°50′ N, 25°45′ W 61°55′ N, 26°45′ W 61°00′ N, 26°30′ W 59°00′ N, 30°00′ W 59°00′ N, 34°00′ W 61°30′ N, 34°00′ W 62°50′ N, 36°00′ W 64°45′ N, 28°30′ W. 2. Notwithstanding paragraph 1, a fishery for redfish may be permitted, by a Union legal act, outside the Redfish Conservation Area in the Irminger Sea and adjacent waters from 11 May to 31 December each year on the basis of scientific advice and provided that NEAFC has established a recovery plan in respect of redfish in that geographical area. Only Union vessels that have been duly authorised by their respective Member State and notified to the Commission as required under Article 5 of Regulation (EU) No 1236/2010 shall participate in this fishery. 3. It shall be prohibited to use trawls with a mesh size of less than 100 millimetres. 4. The conversion factor to be applied to the gutted and headed presentation, including the Japanese cut presentation, of redfish caught in this fishery shall be 1,70. 5. Masters of fishing vessels engaged in the fishery outside the Redfish Conservation Area shall transmit the catch report provided for in Article 9(1)(b) of Regulation (EU) No 1236/2010 on a daily basis after the fishing operations of that calendar day have been completed. It shall indicate the catches on board taken since the last communication of catches. 6. In addition to the provisions of Article 5 of Regulation (EU) No 1236/2010, an authorisation to fish for redfish shall only be valid if the reports transmitted by vessels are in accordance with Article 9(1) of that Regulation and are recorded in accordance with Article 9(3) thereof. 7. The reports referred to in paragraph 6 shall be made in accordance with the relevant rules.

TITLE V RESTRICTIONS ON CERTAIN TYPES OF FISHING AND ASSOCIATED ACTIVITIES

Article 30 Restrictions on the use of demersal towed gears 1. Vessels shall be prohibited from having on board or using any beam trawl of which the beam length, or any beam trawls of which the aggregate beam length measured as the sum of the length of each beam, is greater than 24 metres or can be extended to a length greater than 24 metres. The length of a beam shall be measured between its extremities including all attachments thereto. 1a. Paragraph 1 shall not apply to Region 9. 2. Vessels shall be prohibited from using any beam trawl of which the mesh size lies between 32 and 99 millimetres within either of the following geographical areas: (a)the North Sea north of a line joined by the following points: a point on the east coast of the United Kingdom at latitude 55o N, then east to latitude 55o N, longitude 5o E, then north to latitude 56o N, and finally east to a point on the west coast of Denmark at latitude 56o N; (b)ICES Division Vb and ICES sub-area VI north of latitude 56oN. Within the areas mentioned under (a) and (b), the keeping on board of any beam trawl of which the mesh size lies between 32 and 99 millimetres shall be prohibited, unless such a net is lashed and stowed in accordance with the provisions laid down in Article 20(1) of Regulation (EEC) No 2847/93. 3. Vessels shall be prohibited from using any demersal otter trawl, demersal pair trawl or Danish seine of which the mesh size lies between 80 and 99 millimetres within the geographical area set out in paragraph 2(a). Within this area, the keeping on board of any demersal otter trawl, demersal pair trawl or Danish seine of which the mesh size lies between 80 and 99 millimetres shall be prohibited, unless such a net is lashed and stowed in accordance with the provisions laid down in Article 20(1) of Regulation (EEC) No 2847/93. 4. Vessels shall be prohibited from using any bottom trawl or similar towed nets operating in contact with the bottom of the sea in the area bounded by a line joining the following coordinates:

Latitude 59o54 N	Longitude 6o55 W
Latitude 59o47 N	Longitude 6o47 W
Latitude 59o37 N	Longitude 6o47 W
Latitude 59o37 N	Longitude 7o39 W
Latitude 59o45 N	Longitude 7o39 W
Latitude 59o54 N	Longitude 7o25 W.

5. Vessels shall be prohibited from using any gillnet, entangling net or trammel net at depths greater than 200 metres and any bottom trawl or similar towed nets operating in contact with the bottom of the sea in the areas bounded by a line joining the following coordinates: (a)area named "Madeira and Canaries"

Latitude 27° 00′ N	longitude 19° 00′ W
Latitude 26° 00′ N	longitude 15° 00′ W
Latitude 29° 00′ N	longitude 13° 00′ W
Latitude 36° 00′ N	longitude 13° 00′ W
Latitude 36° 00′ N	longitude 19° 00′ W

(b)area named "Azores"

Latitude 36° 00′ N	longitude 23° 00′ W
Latitude 39° 00′ N	longitude 23° 00′ W
Latitude 42° 00′ N	longitude 26° 00′ W
Latitude 42° 00′ N	longitude 31° 00′ W
Latitude 39° 00′ N	longitude 34° 00′ W
Latitude 36° 00′ N	longitude 34° 00′ W.

Article 31 Unconventional fishing methods 1. The catching of marine organisms using methods incorporating the use of explosives, poisonous or stupefying substances or electric current shall be prohibited. 2. The sale, display or offer for sale of marine organisms caught using methods incorporating the use of any kind of projectile shall be prohibited.

Article 31a Electric fishing in ICES divisions IVc and IVb 1. By way of derogation from Article 31, fishing with beam trawl using electrical pulse current shall be allowed in ICES divisions IVc and IVb south of a rhumb line joined by the following points, which shall be measured according to the WGS84 coordinate system: a point on the east coast of the United Kingdom at latitude 55° N, then east to latitude 55° N, longitude 5° E, then north to latitude 56° N, and finally east to a point on the west coast of Denmark at latitude 56° N. 2. Electrical pulse fishing shall be allowed only when: (a)no more than 5 % of the beam trawler fleet per Member State use the electric pulse trawl; (b)the maximum electrical power in kW for each beam trawl is no more than the length in metres of the beam multiplied by 1,25; (c)the effective voltage between the electrodes is no more than 15 V; (d)the vessel is equipped with an automatic computer management system which records the maximum power used per beam and the effective voltage between electrodes for at least the last 100 tows. It is not possible for non-authorised personnel to modify this automatic computer management system; (e)it is prohibited to use one or more tickler chains in front of the footrope.

Article 32 Restrictions on the use of automatic grading equipment 1. The carrying or use on board a fishing vessel of equipment which is capable of automatically grading by size or by sex herring or mackerel or horse mackerel shall be prohibited. 2. However, the carrying and use of such equipment shall be permitted provided that: (a)the vessel does not simultaneously carry or use on board either towed gear of mesh size less than 70 millimetres or one or more purse seines or similar fishing gears; or (b) (i)the whole of the catch which may be lawfully retained on board is stored in a frozen state, the graded fish are frozen immediately after grading and no graded fish are returned to the sea except as required by Article 19; and (ii)the equipment is installed and located on the vessel in such a way as to ensure immediate freezing and not to allow the return of marine organisms to the sea. 3. Any vessel authorised to fish in the Baltic, Belts or Sound may carry automatic grading equipment in the Kattegat provided that a special fishing permit has been issued to that effect. The special fishing permit shall define the species, areas, time periods and any other required conditions applicable to the use and carriage on board of the grading equipment.

Article 32a Catch handling and discharge restrictions on pelagic vessels 1. The maximum space between bars in the water separator on board pelagic fishing vessels targeting mackerel, herring and horse mackerel operating in the NEAFC Convention Area as defined in Article 3(2) of Regulation (EU) No 1236/2010 shall be 10 millimetres. The bars shall be welded in place. If holes are used in the water separator instead of bars, the maximum diameter of the holes shall not exceed 10 millimetres. Holes in the chutes before the water separator shall not exceed 15 millimetres in diameter. 2. Pelagic vessels operating in the NEAFC Convention Area shall be prohibited from discharging fish under their water line from buffer tanks or Refrigerated seawater (RSW) tanks. 3. Drawings related to the catch handling and discharge capabilities of pelagic vessels targeting mackerel, herring and horse mackerel in the NEAFC Convention Area which are certified by the competent authorities of the flag Member States, as well as any modifications thereto, shall be sent by the master of the vessel to the competent fisheries authorities of the flag Member State. The competent authorities of the flag Member State of the vessels shall carry out periodic verifications of the accuracy of the drawings submitted. Copies shall be carried on board the vessel at all times.

Article 33 Restrictions on the use of purse seines 1. The undertaking of any encirclement with purse seines of any school or group of marine mammals shall be prohibited. 2. Paragraph 1 shall apply, notwithstanding Article 1, to all vessels flying the flag of, or registered in, a Member State, in all waters. 3. However, paragraph 1 shall not apply to those vessels operating under the conditions agreed within the Agreement on the International Dolphin Conservation Programme (Washington, 15 May 1998) and signed by the Community on 12 May 1999. The names and technical characteristics of those vessels shall be contained on a list which shall be drawn up by the Commission in accordance with the procedure referred to in Article 48.

Article 34 Restrictions on fishing activities in the 12-mile zone around the United Kingdom and Ireland 1. Vessels shall be prohibited from using any beam trawl inside the areas within 12 miles of the coasts of the United Kingdom and Ireland, measured from the baselines from which the territorial waters are measured. 2. However, vessels in any of the following categories are authorised to fish in the areas referred to in paragraph 1 using beam trawls: (a)a vessel which entered into service before 1 January 1987, and whose engine power does not exceed 221 kW, and in the case of derated engines did not exceed 300 kW before derating; (b)a vessel which entered into service after 31 December 1986 whose engine is not derated, whose engine power does not exceed 221 kW, and whose length overall does not exceed 24 metres; (c)a vessel which had its engine replaced after 31 December 1986 with an engine which is not derated and whose power does not exceed 221 kW. 3. Notwithstanding paragraph 2, the use of any beam trawl of which the beam length, or of any beam trawls of which the aggregate beam length, measured as the sum of the length of each beam, is greater than nine metres or can be extended to a length greater than nine metres, shall be prohibited, except when operating with gear having a mesh size between 16 and 31 millimetres. The length of a beam shall be measured between its extremities including all attachments thereto. 4. Fishing vessels which do not comply with the criteria specified in paragraphs 2 and 3 shall not be allowed to engage in the fishing activities referred to in those paragraphs. 5. Vessels which may not use beam trawls shall be prohibited from carrying on board such nets within the areas referred to in this Article, unless they are lashed and stowed in accordance with the provisions laid down in Article 20(1) of Regulation (EEC) No 2847/93. 6. Detailed rules for the implementation of this Article shall be drawn up in accordance with the procedure laid down in Article 48.

Article 34a Technical conservation measures in the Irish Sea 1. From 14 February to 30 April, it shall be prohibited to use any demersal trawl, seine or similar towed net, any gillnet, trammel net, entangling net or similar static net or any fishing gear incorporating hooks within that part of ICES division VIIa enclosed by: the east coast of Ireland and the east coast of Northern Ireland, and straight lines sequentially joining the following geographical coordinates: a point on the east coast of the Ards peninsula in Northern Ireland at 54°30′ N, 54°30′ N, 04°50′ W, 53°15′ N, 04°50′ W, a point on the east coast of Ireland at 53°15′ N. 2. By way of derogation from paragraph 1, within the area and time period referred to in that paragraph: (a)the use of demersal otter trawls shall be permitted, provided that no other type of fishing gear is retained on board and that such nets: are of the mesh size ranges 70-79 millimetres or 80-99 millimetres, are of only one of the permitted mesh size ranges, incorporate no individual mesh, irrespective of its position within the net, with a mesh size greater than 300 millimetres, and are deployed only within an area enclosed by sequentially joining with rhumb lines the following coordinates, which shall be measured according to the WGS84 system: 53°30′ N, 05°30′ W 53°30′ N, 05°20′ W 54°20′ N, 04°50′ W 54°30′ N, 05°10′ W 54°30′ N, 05°20′ W 54°00′ N, 05°50′ W 54°00′ N, 06°10′ W 53°45′ N, 06°10′ W 53°45′ N, 05°30′ W 53°30′ N, 05°30′ W; (b)the use of any demersal trawl, seine or similar towed net with a separator panel or a sorting grid shall be permitted, provided that no other type of fishing gear is retained on board and that such nets: comply with the conditions laid down in point (a), in the case of a separator panel, are constructed in conformity with the technical details provided in the Annex of Council Regulation (EC) No 254/2002 of 12 February 2002 establishing measures to be applicable in 2002 for the recovery of the stock of cod in the Irish Sea (ICES) division VIIa)OJ L 41, 13.2.2002, p. 1., and in the case of sorting grids, are in accordance with points 2 to 5 of Annex XIVa to this Regulation; (c)the use of demersal trawl, seine or similar towed net with a separator panel or a sorting grid shall also be permitted within an area enclosed by sequentially joining with rhumb lines the following coordinates, which shall be measured according to the WGS84 system: 53°45′ N, 06°00′ W 53°45′ N, 05°30′ W 53°30′ N, 05°30′ W 53°30′ N, 06°00′ W 53°45′ N, 06°00′ W.

Article 34b Use of gillnets in ICES divisions IIIa, IVa, Vb, VIa, VIb, VIIb, c, j, k and ICES sub-areas VIII, IX, X and XII east of 27° W 1. Union vessels shall not deploy bottom set gillnets, entangling nets and trammel nets at any position where the charted depth is greater than 200 metres in ICES divisions IIIa, IVa, Vb, VIa, VIb, VII b, c, j, k and ICES sub-areas VIII, IX and X and XII east of 27° W. 2. By way of derogation from paragraph 1, it shall be permitted to use the following gears: (a)Gillnets in ICES divisions IIIa, IVa, Vb, VIa, VIb, VII b, c, j, k and ICES sub-area XII east of 27° W with a mesh size equal to or greater than 120 millimetres and less than 150 millimetres, gillnets in ICES divisions VIIIa, b, d and ICES sub-area X with a mesh size equal to or greater than 100 millimetres and less than 130 millimetres and gillnets in ICES divisions VIIIc and ICES sub-area IX with a mesh size equal to or greater than 80 millimetres and less than 110 millimetres, provided that: they are deployed in waters with a charted depth of less than 600 metres, they are no more than 100 meshes deep, and have a hanging ratio of not less than 0,5, they are rigged with floats or equivalent flotation, they each have a maximum length of 5 nautical miles, and the total length of all nets deployed at any one time does not exceed 25 km per vessel, the maximum soak time is 24 hours; (b)Entangling nets with a mesh size equal to or greater than 250 millimetres, provided that: they are deployed in waters with a charted depth of less than 600 metres, they are no more than 15 meshes deep, and have a hanging ratio of not less than 0,33, they are not rigged with floats or other means of floatation, they each have a maximum length of 10 km, and the total length of all nets deployed at any one time does not exceed 100 km per vessel, the maximum soak time is 72 hours; (c)Gillnets in ICES divisions IIIa, IVa, Vb, VIa, VIb, VIIb, c, j, k and ICES sub-area XII east of 27° W with a mesh size equal to or greater than 100 millimetres and less than 130 millimetres, provided that: they are deployed in waters with a charted depth of more than 200 metres and less than 600 metres, they are no more than 100 meshes deep, and have a hanging ratio of not less than 0,5, they are rigged with floats or equivalent floatation, they each have a maximum length of 4 nautical miles, and the total length of all nets deployed at any one time does not exceed 20 km per vessel, the maximum soak time is 24 hours, no less than 85 % of the retained catch by weight is hake, the number of vessels participating in the fishery does not rise above the level recorded in 2008, prior to leaving port the master of the vessel participating in this fishery records in the log-book, the quantity and total length of gear carried on board the vessel. At least 15 % of departures shall be subject to inspection, as verified in the Union logbook for that trip at the time of landing the master of the vessel has on board 90 % of the gear, and the quantity of all species caught greater than 50 kg, including all quantities discarded greater than 50 kg, is recorded in the Union logbook; (d)Trammel nets in ICES sub-area IX with a mesh size equal to or greater than 220 millimetres, provided that: they are deployed in waters with a charted depth of less than 600 metres, they are no more than 30 meshes deep, and have a hanging ratio of not less than 0,44, they are not rigged with floats or other means of floatation, they each have a maximum length of 5 km, and the total length of all nets deployed at any one time does not exceed 20 km per vessel, the maximum soak time is 72 hours. 3. However, this derogation shall not apply in the NEAFC Regulatory Area. 4. All vessels deploying bottom set gillnets, entangling or trammel nets at any position where the charted depth is greater than 200 metres in ICES divisions IIIa, IVa, Vb, VIa, VIb, VII b, c, j, k and ICES sub-areas XII east of 27° W, VIII, IX and X, shall be issued with a fishing authorisation in accordance with Article 7 of Regulation (EC) No 1224/2009. 5. Only one of the types of gear described in paragraph 2(a), (b) or (d) shall be retained on board the vessel at any one time. Vessels may carry on board nets with a total length that is 20 % greater than the maximum length of the fleets that may be deployed at any one time. 6. The master of a vessel with a fishing authorisation referred to in paragraph 4 shall record in the logbook the amount and lengths of gear carried by a vessel before it leaves port and when it returns to port, and shall account for any discrepancy between the two quantities. 7. The competent authorities shall have the right to remove unattended gear at sea in ICES divisions IIIa, IVa, Vb, VIa, VIb, VII b, c, j, k and ICES sub-areas XII east of 27° W, VIII, IX and X, in the following situations: (a)the gear is not properly marked; (b)the buoy markings or VMS data indicate that the owner has not been located at a distance less than 100 nautical miles from the gear for more than 120 hours; (c)the gear is deployed in waters with a charted depth greater than that which is permitted; (d)the gear is of an illegal mesh size. 8. The master of a vessel with a fishing authorisation referred to in paragraph 4 shall record in the logbook the following information during each fishing trip: the mesh size of the net deployed, the nominal length of one net, the number of nets in a fleet, the total number of fleets deployed, the position of each fleet deployed, the depth of each fleet deployed, the soak time of each fleet deployed, the quantity of any gear lost, its last known position and date of loss. 9. Vessels fishing with a fishing authorisation referred to in paragraph 4 shall only be permitted to land in the ports designated by the Member States pursuant to Article 7 of Regulation (EC) 2347/2002. 10. The quantity of sharks retained on board by any vessel using the gear type described in paragraph 2(b) and (d) shall be no more than 5 %, by live-weight, of the total quantity of marine organisms retained on board. 11. After consulting STECF, the Commission may adopt implementing acts excluding specific fisheries of a Member State, in ICES sub-areas VIII, IX and X, from the application of paragraphs 1 to 9, where information provided by Member States shows that those fisheries result in a very low level of shark by-catches and of discards.

Article 34c Condition for fisheries using certain towed gears authorised in the Bay of Biscay 1. By way of derogation from the provisions laid down in Article 5(2) of Commission Regulation (EC) No 494/2002 of 19 March 2002 establishing additional technical measures for the recovery of the stock of hake in ICES sub-areas III, IV, V, VI and VII and ICES divisions VIIIa, b, d and eOJ L 77, 20.3.2002, p. 8., it shall be permitted to conduct fishing activity using trawls, Danish seines and similar gears, with the exception of beam trawls, with a mesh size range of 70-99 millimetres in the area defined in Article 5(1)(b) of Regulation (EC) No 494/2002 if the gear is fitted with a square mesh panel in accordance with Annex XIVb. 2. When fishing in ICES divisions VIII a and b, it shall be permitted to use a selective grid and its attachments in front of the codend and/or a square mesh panel with a mesh size equal to or more than 60 millimetres in the lower part of the extension piece in front of the codend. The provisions laid down in Article 4(1), Article 6 and Article 9(1) of this Regulation and in Article 3(a) and (b) of Regulation (EC) No 494/2002 shall not apply to the section of the trawl where those selective devices are inserted.

Article 34d Measures for the protection of vulnerable deep-sea habitats in the NEAFC Regulatory Area 1. It shall be prohibited to conduct bottom trawling and fishing with static gear, including bottom set gillnets and bottom set longlines, within the areas enclosed by sequentially joining with rhumb lines the following coordinates, which shall be measured according to the WGS84 system: Part of the Reykjanes Ridge: 55°04.5327′ N, 36°49.0135′ W 55°05.4804′ N, 35°58.9784′ W 54°58.9914′ N, 34°41.3634′ W 54°41.1841′ N, 34°00.0514′ W 54°00′ N, 34°00′ W 53°54.6406′ N, 34°49.9842′ W 53°58.9668′ N, 36°39.1260′ W 55°04.5327′ N, 36°49.0135′ W Northern MAR Area: 59°45′ N, 33°30′ W 57°30′ N, 27°30′ W 56°45′ N, 28°30′ W 59°15′ N, 34°30′ W 59°45′ N, 33°30′ W Middle MAR Area (Charlie-Gibbs Fracture zone and Subpolar Frontal Region): 53°30′ N, 38°00′ W 53°30′ N, 36°49′ W 55°04.5327′ N, 36°49′ W 54°58.9914′ N, 34°41.3634′ W 54°41.1841′ N, 34°00′ W 53°30′ N, 30°00′ W 51°30′ N, 28°00′ W 49°00′ N, 26°30′ W 49°00′ N, 30°30′ W 51°30′ N, 32°00′ W 51°30′ N, 38°00′ W 53°30′ N, 38°00′ W Southern MAR Area: 44°30′ N, 30°30′ W 44°30′ N, 27°00′ W 43°15′ N, 27°15′ W 43°15′ N, 31°00′ W 44°30′ N, 30°30′ W The Altair Seamounts: 45°00′ N, 34°35′ W 45°00′ N, 33°45′ W 44°25′ N, 33°45′ W 44°25′ N, 34°35′ W 45°00′ N, 34°35′ W The Antialtair Seamounts: 43°45′ N, 22°50′ W 43°45′ N, 22°05′ W 43°25′ N, 22°05′ W 43°25′ N, 22°50′ W 43°45′ N, 22°50′ W Hatton Bank: 59°26′ N, 14°30′ W 59°12′ N, 15°08′ W 59°01′ N, 17°00′ W 58°50′ N, 17°38′ W 58°30′ N, 17°52′ W 58°30′ N, 18°22′ W 58°03′ N, 18°22′ W 58°03′ N, 17°30′ W 57°55′ N, 17°30′ W 57°45′ N, 19°15′ W 58°11.15′ N, 18°57.51′ W 58°11.57′ N, 19°11.97′ W 58°27.75′ N, 19°11.65′ W 58°39.09′ N, 19°14.28′ W 58°38.11′ N, 19°01.29′ W 58°53.14′ N, 18°43.54′ W 59°00.29′ N, 18°01.31′ W 59°08.01′ N, 17°49.31′ W 59°08.75′ N, 18°01.47′ W 59°15.16′ N, 18°01.56′ W 59°24.17′ N, 17°31.22′ W 59°21.77′ N, 17°15.36′ W 59°26.91′ N, 17°01.66′ W 59°42.69′ N, 16°45.96′ W 59°20.97′ N, 15°44.75′ W 59°21′ N, 15°40′ W 59°26′ N, 14°30′ W North-West Rockall: 57°00′ N, 14°53′ W 57°37′ N, 14°42′ W 57°55′ N, 14°24′ W 58°15′ N, 13°50′ W 57°57′ N, 13°09′ W 57°50′ N, 13°14′ W 57°57′ N, 13°45′ W 57°49′ N, 14°06′ W 57°29′ N, 14°19′ W 57°22′ N, 14°19′ W 57°00′ N, 14°34′ W 56°56′ N, 14°36′ W 56°56′ N, 14°51′ W 57°00′ N, 14°53′ W South-West Rockall (Empress of Britain Bank): 56°24′ N, 15°37′ W 56°21′ N, 14°58′ W 56°04′ N, 15°10′ W 55°51′ N, 15°37′ W 56°10′ N, 15°52′ W 56°24′ N, 15°37′ W Logachev Mound: 55°17′ N, 16°10′ W 55°34′ N, 15°07′ W 55°50′ N, 15°15′ W 55°33′ N, 16°16′ W 55°17′ N, 16°10′ W West Rockall Mound: 57°20′ N, 16°30′ W 57°05′ N, 15°58′ W 56°21′ N, 17°17′ W 56°40′ N, 17°50′ W 57°20′ N, 16°30′ W 2. Where, in the course of fishing operations in new and existing bottom fishing areas within the NEAFC Regulatory Area, the quantity of live coral or live sponge caught per gear set exceeds 60 kg of live coral and/or 800 kg of live sponge, the vessel shall inform its flag State, cease fishing and move at least 2 nautical miles away from the position that the evidence suggests is closest to the exact location where this catch was made.

Article 34e Measures for the protection of vulnerable deep-sea habitats in ICES divisions VIIc, j and k 1. It shall be prohibited to conduct bottom trawling and fishing with static gear, including bottom set gillnets and bottom set longlines, within the areas enclosed by sequentially joining with rhumb lines the following coordinates, which shall be measured according to the WGS84 coordinate system: Belgica Mound Province: 51°29.4′ N, 11°51.6′ W 51°32.4′ N, 11°41.4′ W 51°15.6′ N, 11°33.0′ W 51°13.8′ N, 11°44.4′ W 51°29.4′ N, 11°51.6′ W Hovland Mound Province: 52°16.2′ N, 13°12.6′ W 52°24.0′ N, 12°58.2′ W 52°16.8′ N, 12°54.0′ W 52°16.8′ N, 12°29.4′ W 52°04.2′ N, 12°29.4′ W 52°04.2′ N, 12°52.8′ W 52°09.0′ N, 12°56.4′ W 52°09.0′ N, 13°10.8′ W 52°16.2′ N, 13°12.6′ W North-West Porcupine Bank Area I: 53°30.6′ N, 14°32.4′ W 53°35.4′ N, 14°27.6′ W 53°40.8′ N, 14°15.6′ W 53°34.2′ N, 14°11.4′ W 53°31.8′ N, 14°14.4′ W 53°24.0′ N, 14°28.8′ W 53°30.6′ N, 14°32.4′ W North-West Porcupine Bank Area II: 53°43.2′ N, 14°10.8′ W 53°51.6′ N, 13°53.4′ W 53°45.6′ N, 13°49.8′ W 53°36.6′ N, 14°07.2′ W 53°43.2′ N, 14°10.8′ W South-West Porcupine Bank: 51°54.6′ N, 15°07.2′ W 51°54.6′ N, 14°55.2′ W 51°42.0′ N, 14°55.2′ W 51°42.0′ N, 15°10.2′ W 51°49.2′ N, 15°06.0′ W 51°54.6′ N, 15°07.2′ W 2. All pelagic vessels fishing in the areas for the protection of vulnerable deep-sea habitats set out in paragraph 1 of this Article shall be on a list of authorised vessels and be issued with a fishing authorisation in accordance with Article 7 of Regulation (EC) No 1224/2009. Vessels included in the list of authorised vessels shall carry on board exclusively pelagic gear. 3. Pelagic vessels intending to fish in an area for the protection of vulnerable deep-sea habitats as set out in paragraph 1 of this Article shall give four hours advance notification of their intention to enter an area for the protection of vulnerable deep-sea habitats to the Irish Fisheries Monitoring Centre (FMC) as defined in Article 4(15) of Regulation (EC) No 1224/2009. They shall at the same time notify quantities of fish retained on board. 4. Pelagic vessels fishing in an area for the protection of vulnerable deep-sea habitats as set out in paragraph 1 shall have an operational, fully functioning secure Vessel Monitoring System (VMS) which complies fully with the respective rules when present in an area for the protection of vulnerable deep-sea habitats. 5. Pelagic vessels fishing in an area for the protection of vulnerable deep-sea habitats as set out in paragraph 1 shall make VMS reports every hour. 6. Pelagic vessels who have concluded fishing in an area for the protection of vulnerable deep-sea habitats as set out in paragraph 1 shall inform the Irish FMC on departure from the area. They shall at the same time notify quantities of fish retained on board. 7. Fishing for pelagic species in an area for the protection of vulnerable deep-sea habitats as set out in paragraph 1 shall be restricted to having onboard or fishing with nets with a mesh size in the range of 16-31 millimetres or 32-54 millimetres.

Article 34f Measures for the protection of a vulnerable deep-sea habitat in ICES division VIIIc 1. It shall be prohibited to conduct bottom trawling and fishing with static gear, including bottom set gillnets and bottom set longlines, within the area enclosed by sequentially joining with rhumb lines the following coordinates, which shall be measured according to the WGS84 system:El Cachucho: 44°12′ N, 05°16′ W 44°12′ N, 04°26′ W 43°53′ N, 04°26′ W 43°53′ N, 05°16′ W 44°12′ N, 05°16′ W 2. By way of derogation from the prohibition set out in the paragraph 1, vessels that conducted fisheries with bottom set longlines in 2006, 2007 and 2008 targeting greater forkbeard may obtain from their fishing authorities a fishing authorisation in accordance with Article 7 of Regulation (EC) No 1224/2009 that allows them to continue conducting that fishery in the area south of 44°00.00′ N. All vessels having obtained this fishing authorisation shall, regardless of their overall length, have in use an operational, fully functioning secure VMS which complies with the respective rules, when conducting fisheries in the area set out in paragraph 1.

Article 34g Restrictions on fishing activities in the 24-mile zone around Mayotte Vessels shall be prohibited from using any purse-seine on tuna and tuna-like schools of fish inside the area within 24 miles of the coasts of Mayotte, as an outermost region within the meaning of Article 349 of the Treaty on the Functioning of the European Union, measured from the baselines from which territorial waters are measured.

TITLE VI SPECIFIC PROVISIONS FOR THE SKAGERRAK AND KATTEGAT

Article 35 Notwithstanding Article 19(1), undersized marine organisms caught in the Skagerrak or Kattegat may be retained on board, or be transhipped, landed, transported, stored, sold, displayed or offered for sale within a limit of 10 % by live weight of the total catches retained on board.

Article 36 Salmon and sea trout shall not be retained on board or be transhipped, landed, transported, stored, sold, displayed or offered for sale, but shall be returned immediately to the sea, when taken within any part of the Skagerrak and Kattegat situated outside the four-mile limit measured from Member States' baselines.

Article 37 1. The use of trawls having a mesh size of less than 32 millimetres from 1 July to 15 September in the waters situated within three miles of the baselines in the Skagerrak and Kattegat shall be prohibited. 2. However, when trawling within the waters and during the period referred to in paragraph 1: for northern shrimp (Pandalus borealis), nets with a minimum mesh size of 30 millimetres may be used, for eelpout (Zoarces viviparus), gobies (Gobiidae) or scorpion fish (Cottus ssp.) to be used as bait, nets with any mesh size may be used.

Article 38 The retention on board of any quantity of herring, mackerel or sprat caught using trawls or purse seines between Saturday midnight and Sunday midnight in the Skagerrak, and between Friday midnight and Sunday midnight in the Kattegat shall be prohibited.

Article 39 The use of any beam trawl in the Kattegat shall be prohibited.

Article 40 During the periods and within the areas referred to in Articles 37, 38 and 39 of this Regulation, where trawls or beam trawls may not be used, the carrying on board of such nets shall be prohibited, unless they are lashed and stowed in accordance with the provisions laid down in Article 20(1) of Regulation (EEC) No 2847/93.

Article 41 Notwithstanding Article 31, electric current or harpoon guns may be used to catch tuna and basking shark (Cetorhinus maximus) in the Skagerrak and Kattegat.

TITLE VII TECHNICAL PROVISIONS

Article 42 Processing operations 1. The carrying out on board a fishing vessel of any physical or chemical processing of fish to produce fish-meal, fish-oil, or similar products, or to tranship catches of fish for such purposes shall be prohibited. This prohibition shall not apply to the processing or transhipment of offal. 2. Paragraph 1 shall not apply to the production on board a fishing vessel of surimi and fish pulp.

Article 43 Scientific research 1. This Regulation shall not apply to fishing operations conducted solely for the purpose of scientific investigations which are carried out with the permission and under the authority of the Member State or Member States concerned, and of which the Commission and the Member State or Member States in whose waters the research is carried out have been informed in advance. 2. Marine organisms caught for the purposes specified in paragraph 1 may be sold, stored, displayed or offered for sale, provided that: they meet the standards laid down in Annex XII to this Regulation and the marketing standards adopted pursuant to Article 2 of Council Regulation (EEC) No 3759/92 of 17 December 1992 on the common organisation of the market in fishery and aquaculture productsOJ L 388, 31.12.1992, p. 1. Regulation as last amended by Regulation (EC) No 3318/94 (OJ L 350, 31.12.1994, p. 15)., or they are sold directly for purposes other than human consumption.

Article 44 Artificial restocking and transplantation 1. This Regulation shall not apply to fishing operations conducted solely for the purpose of artificial restocking or transplantation of marine organisms which are carried out with the permission and under the authority of the Member State or Member States concerned. Where the artificial restocking or transplantation is carried out in the waters of another Member State or Member States, the Commission and all the Member States concerned shall be informed in advance. 2. Marine organisms caught for the purposes specified in paragraph 1 of this Article, and subsequently returned alive to the sea, may be sold, stored, displayed or offered for sale, provided that the marketing standards adopted pursuant to Article 2 of Regulation (EEC) No 3759/92 are complied with.

TITLE VIII FINAL PROVISIONS

Article 45 1. Where the conservation of stocks of marine organisms calls for immediate action, the Commission may, in addition to or by way of derogation from this Regulation, adopt any measures necessary in accordance with the procedure referred to in Article 48. 2. Where the conservation of certain species or fishing grounds is seriously threatened, and where any delay would result in damage which would be difficult to repair, a Member State may take appropriate non-discriminatory conservation measures in respect of the waters under its jurisdiction. 3. The measures referred to in paragraph 2, together with an explanatory memorandum, shall be communicated to the Commission and the other Member States as soon as they are adopted. Within 10 working days of receipt of such notification, the Commission shall confirm such measures, or require their cancellation or amendment. The Commission's decision shall be immediately notified to the Member States. Member States may refer the Commission's decision to the Council within 10 working days of receiving this notification. The Council, acting by a qualified majority, may adopt a different decision within one month.

Article 46 1. Member States may take measures for the conservation and management of stocks: (a)in the case of strictly local stocks which are of interest solely to the Member State concerned; or (b)in the form of conditions or detailed arrangements designed to limit catches by technical measures: (i)supplementing those laid down in the Community legislation on fisheries; or (ii)going beyond the minimum requirements laid down in the said legislation;provided that such measures apply solely to fishing vessels flying the flag of the Member State concerned and registered in the Community or, in the case of fishing activities which are not conducted by a fishing vessel, to persons established in the Member State concerned. 2. The Commission shall be informed, in time for it to present its observations, of any plans to introduce or amend national technical measures. If the Commission so requests within one month of such notification, the Member State concerned shall suspend the entry into force of the measures planned until three months have elapsed from the date of the said notification, so that the Commission can decide within that period whether the measures in question comply with the provisions of paragraph 1. Where the Commission finds, by a decision which it shall communicate to all Member States, that a planned measure does not comply with the provisions of paragraph 1, the Member State concerned may not bring it into force without making the necessary amendments thereto. The Member State concerned shall immediately inform the other Member States and the Commission of the measures adopted, having made any amendments which may be necessary. 3. Member States shall provide the Commission, on request, with all particulars necessary to assess whether their national technical measures comply with the provisions of paragraph 1. 4. At the initiative of the Commission, or at the request of any Member State, the question of whether a national technical measure applied by a Member State complies with paragraph 1 of this Article may be the subject of a decision taken in accordance with the procedure laid down in Article 48. Should such a decision be taken, the third and fourth subparagraphs of paragraph 2 shall apply. 5. Measures relating to fishing from the shore shall be communicated by the Member State concerned to the Commission for information purposes only.

Article 47 1. At the latest one year after the date of entry into force of this Regulation, the Council shall decide, on the basis of a proposal from the Commission, on the establishment of rules for the use of mesh size combinations to be applied on the date of application of this Regulation. At the latest three years after the date of application of this Regulation, the Council shall decide, on the basis of a proposal from the Commission, on revisions and amendments to the conditions laid out in Annexes I to XI, to be applied within one year after that decision. 2. During the years 1998, 1999 and 2000 the Member States when applying for funding by the Commission for experimental projects shall give priority to experimental projects that are concerned with the utility of square-meshed panels or other devices for increasing the selectivity of towed gears. The Commission, in assessing experimental projects for funding, shall give priority to such projects. The Commission shall report, and at the same time submit appropriate proposals, on the findings of the said experimental projects to the Council at the latest four years after the date of adoption of this Regulation. The Council shall decide on these proposals at the latest one year after the date of submission.

Article 48 Detailed rules for the implementation of this Regulation shall be adopted in accordance with the procedure laid down in Article 18 of Regulation (EEC) No 3760/92. These rules may include, inter alia: technical rules for the determination of twine thickness, technical rules for the determination of mesh size, rules for sampling, lists and technical descriptions of devices that may be attached to nets, technical rules for measuring engine power, technical rules relating to square-meshed netting, technical rules relating to netting materials, amendments to rules for the use of mesh size combinations.

Article 49 The following Articles of, and Annexes to, Regulation (EC) No 894/97 shall be repealed as from 1 January 2000: Articles 1 to 10, Articles 12 to 17, Annexes I to VII. References to the said Regulation shall be construed as references to this Regulation and shall be read in accordance with the correlation table set out in Annex XV. The scientific names of marine organisms specifically mentioned in this Regulation are set out in Annex XIV.

Article 50 This Regulation shall enter into force on the seventh day following its publication in the Official Journal of the European Communities. It shall apply from 1 January 2000, with the exception of Article 32(3) and Article 47, which shall apply from the date of entry into force of this Regulation.

This Regulation shall be binding in its entirety and directly applicable in all Member States. ANNEX I TOWED GEARS: Regions 1 and 2, except Skagerrak and Kattegat

Mesh size ranges, target species, and required catch percentages applicable to the use of a single mesh size range In the North Sea from 1 March to 31 October, and during the whole of the year in the remainder of Regions 1 and 2, except Skagerrak and Kattegat. In the North Sea, from 1 November to the last day of February. The catch retained on board must consist of: at least 90 % of any mixture of two or more target species, or at least 60 % of any one of the target species and no more than 5 % of any mixture of cod, haddock, and saithe and no more than 15 % of any mixture of the species marked with the symbol "Ø". The catch retained on board must consist of: at least 90 % of any mixture of two or more target species, or at least 60 % of any one of the target species and no more than 5 % of any mixture of cod, haddock, and saithe and no more than 15 % of any mixture of the species marked with the symbol "ÿ". Provisions regarding limitations on catches of herring which may be retained on board when taken with nets of 16 to 31 mm mesh size are stipulated in Community legislation fixing, for certain fish stocks and groups of fish stocks, total allowable catches and certain conditions under which they may be fished. During the first year following the date of application of this Regulation a minimum percentage of target species of 50 % shall pertain with respect to catches taken in Region 2 with the exception of the North Sea, ICES Division Vb and sub-area VI north of latitude 56oN.

Target species		Mesh size range (millimetres)
		< 16	16 to 31		32 to 54		55 to 69	70 to 79	80 to 99		≥ 100
		Minimum percentage of target species
		95	90/60	60	30	90/60	90	35	30	70	None
Sand eels (Ammodytidae)		×	×			×		×	×	×	×
Sand eels (Ammodytidae)			×			×		×	×	×	×
Norway pout (Trisopterus esmarkii)			×			×		×	×	×	×
Smelt (Atherina spp. and Osmerus spp.)			×			×		×	×	×	×
Poor cod (Trisopterus minutus)			×			×		×	×	×	×
Silvery cod (Gadus argenteus)			×			×		×	×	×	×
Red bandfish (Cepolidae)			×			×		×	×	×	×
Sprat (Sprattus sprattus)			×			×		×	×	×	×
Eel (Anguilla anguilla)			×			×		×	×	×	×
Anchovy (Engraulis encrasicholus)			×			×		×	×	×	×
Blue whiting (Micromesistius poutassou)			×			×		×	×	×	×
Argentines (Argentinidae)			×			×		×	×	×	×
Sardine (Sardina pilchardus)			×			×		×	×	×	×
Shrimps/Common prawns (Pandalus montagui, Crangon spp., Palaemon spp.)				×	×	×		×	×	×	×
Mackerel (Scomber spp.)	Ø					×	×	×	×	×	×
Horse mackerel (Trachurus spp.)						×		×	×	×	×
Herring (Clupea harengus)						×		×	×	×	×
Squids (Loliginidae, Ommastrephidae)	Ø					×		×	×	×	×
Garfish (Belone spp.)	Ø					×		×	×	×	×
Bib (Trisopterus luscus)	Ø					×		×	×	×	×
Prawns (Pandalus spp., Parapenaeus longirostris)	Ø				×			×	×	×	×
Conger (Conger conger)	Ø ÿ							×	×	×	×
Weevers (Trachinidae)	Ø ÿ							×	×	×	×
Gurnards (Triglidae)	ÿ							×	×	×	×
Octopus (Octopus vulgaris)	Ø ÿ							×	×	×	×
Squat lobsters (Galatheidae)	Ø ÿ							×	×	×	×
Norway lobster (Nephrops norvegicus)	Ø ÿ							×	×	×	×
Sole (Solea vulgaris)	Ø ÿ									×	×
Plaice (Pleuronectes platessa)	Ø ÿ									×	×
Hake (Merluccius merluccius)	Ø ÿ									×	×
Megrim (Lepidorhombus spp.)	Ø ÿ									×	×
Whiting (Merlangius merlangus)	Ø ÿ									×	×
Brill (Scophthalmus rhombus)	Ø ÿ									×	×
Pollack (Pollachius pollachius)	Ø ÿ									×	×
Dab (Limanda limanda)	Ø ÿ									×	×
Cuttlefish (Sepia officinalis)	Ø ÿ									×	×
Sea bass (Dicentrarchus labrax)	Ø ÿ									×	×
Flounder (Platichthys flesus)	Ø ÿ									×	×
Lemon sole (Microstomus kitt)	Ø ÿ									×	×
Dogfish (Scyliorhinidæ)	Ø ÿ									×	×
Witch (Glyptocephalus cynoglossus)	Ø ÿ									×	×
John Dory (Zeus faber)	Ø ÿ									×	×
Queen scallop (Chlamys opercularis)	Ø ÿ									×	×
Variegated scallop (Chlamys varia)	Ø ÿ									×	×
Red mullets (Mullidae)	Ø ÿ									×	×
Grey mullets (Mugilidae)	Ø ÿ									×	×
Grenadiers (Nezumia spp., Trachyrhynchus spp., Malococephalus spp.)	Ø ÿ									×	×
Hairtails (Trichiuridae)	Ø ÿ									×	×
Anglers (Lophiidae)	Ø ÿ									×	×
Skates and rays (Rajidae)	Ø ÿ									×	×
Sea breams (Sparidae)	Ø ÿ									×	×
Turbot (Psetta maxima)	Ø ÿ									×	×
Boarfish (Caproidae)						×
All other marine organisms											×

ANNEX II TOWED GEAR: Region 3, except ICES Division IXa east of longitude 7o 23′ 48″ W

Mesh size ranges, target species and required catch percentages applicable to the use of a single mesh size range

Target species	Mesh size range (millimetres)
	16 to 31		32 to 54		55 to 59		60 to 69	≥ 70
	Minimum percentage of target species
	50 %	90 %	90 %	90 %	30 %	70 %	70 %	None
Sand eels (Ammodytidae)		×		×		×	×	×
Norway pout (Trisopterus esmarkii)		×		×		×	×	×
Sprat (Sprattus sprattus)		×		×		×	×	×
Eel (Anguilla anguilla)		×		×		×	×	×
Anchovy (Engraulis encrasicolus)		×		×		×	×	×
Smelt (Atherina spp. and Osmerus spp.)		×		×		×	×	×
Poor cod (Trisopterus minutus)		×		×		×	×	×
Silvery cod (Gadus argenteus)		×		×		×	×	×
Red bandfish (Cepolidae)		×		×		×	×	×
Sardine (Sardina pilchardus)		×		×		×	×	×
Swimming crab (Polybius henslowi)	×			×		×	×	×
Shrimps (Pandalus mantagui, Crangon spp., Palaemon spp.)	×		×	×	×	×	×	×
Mackerel (Scomber spp.)				×		×	×	×
Horse mackerel (Trachurus spp.)				×		×	×	×
Herring (Clupea harengus)				×		×	×	×
Blue whiting (Micromesistius poutassou)				×		×	×	×
Argentines (Argentinidae)				×		×	×	×
Squids (Loliginidae, Ommastrephidae)				×		×	×	×
Garfish (Belone spp.)				×		×	×	×
Pouting (Trisopterus spp.)				×		×	×	×
Wedge sole (Dicologoglossa cuneata)				×		×	×	×
Prawns (Pandalus spp.)			×		×	×	×	×
Breams (Bramidae, Berycidae)						×	×	×
Conger (Conger conger)						×	×	×
Sea breams (Sparidae except Spondyliosoma cantharus)						×	×	×
Rockfish (Scorpaenidae)						×	×	×
Sole (Microchirus azevia, Microchirus variegatus)						×	×	×
Forkbeard (Phycis spp.)							×	×
Weevers (Trachinidae)						×	×	×
Gurnards (Triglidae)						×	×	×
Picarels (Centracanthidae)						×	×	×
Octopus (Octopus vulgaris, Eledone cirrosa)						×	×	×
Wrasses (Labridae)						×	×	×
Shrimps (Aristeus antennatus, Aristaeomorpha foliacea, Parapenaeus longirostris)					×		×	×
Cuttlefish (Sepia officinalis)							×	×
Grenadiers (Malacocephalus spp., Nezumia spp., Trachyrhynchus spp.)							×	×
Dogfish (Scyliorhinidae)						s	×	×
Common mora (Mora moro)							×	×
Squat lobsters (Galatheidae)							×	×
John Dory (Zeus faber)							×	×
Red mullets (Mullidae)							×	×
Boarfish (Caproidae)				×
All other marine organisms								×

ANNEX III TOWED GEARS: ICES Division IXa east of longitude 7o 23′ 48″ W

Mesh size ranges, target species and required catch percentages applicable to the use of a single mesh size range Quantities of any mixture of the other species mentioned in Annex XII retained on board may not exceed 10 % by weight of the total catch retained on board.

Target species	Mesh size range (millimetres)
	40 to 54	≥ 55
	Minimum percentage of target species
	60 %	None
Grey mullets (Mugilidae)	×	×
Sea breams (Sparidae)	×	×
Red mullets (Mullidae)	×	×
Gurnards (Triglidae)	×	×
Weevers (Trachinidae)	×	×
Wrasses (Labridae)	×	×
Forkbeard (Phycis spp.)	×	×
Wedge sole (Dicologoglossa cuneata)	×	×
Spotted flounder (Citharus linguatula)	×	×
Conger (Conger conger)	×	×
Mantis shrimp (Squilla mantis)	×	×
Shrimps (Parapenaeus longirostris, Pandalus spp.)	×	×
Squids (Ommastrephidae, Loliginidae Alloteuthis spp.)	×	×
Octopus (Octopus vulgaris)	×	×
Cuttlefish (Sepia spp.)	×	×
Mackerel (Scomber spp.)	×	×
Horse mackerel (Trachurus spp.)	×	×
Blue whiting (Micromesistius poutassou)	×	×
Eel (Anguilla anguilla)	×	×
Smelt (Atherina spp., Osmerus spp.)	×	×
Garfish (Belone spp.)	×	×
All other marine organisms		×

ANNEX IV TOWED GEARS: — Skagerrak and Kattegat

Mesh size ranges, target species and required catch percentages applicable to the use of a single mesh size range Only within 4 miles from the baselines. Outside 4 miles from the baselines. From 1 March to 31 October in Skagerrak and from 1 March to 31 July in Kattegat. From 1 November to the last day of February in Skagerrak and from 1 August to the last day of February in Kattegat. When applying this mesh size range, the codend shall be constructed of square mesh netting with a sorting grid in accordance with Annex XIVa of this Regulation. The catch retained on board shall consist of no more than 10 % of any mixture of cod, haddock, hake, plaice, witch, lemon sole, sole, turbot, brill, flounder, mackerel, megrim, whiting, dab, saithe, Norway lobster and lobster. The catch retained on board shall consist of no more than 50 % of any mixture of cod, haddock, hake, plaice, witch, lemon sole, sole, turbot, brill, flounder, herring, mackerel, megrim, dab, saithe, Norway lobster and lobster. The catch retained on board shall consist of no more than 60 % of any mixture of cod, haddock, hake, plaice, witch, lemon sole, sole, turbot, brill, flounder, megrim, whiting, dab, saithe and lobster.

Species	Mesh size range (mm)
	< 16	16-31		32-69		35-69	70-89	≥ 90
	Minimum percentage of target species
	50 %	50 %	20 %	50 %	20 %	20 %	30 %	none
Sand eel (Ammodytidae)	X	X	X	X	X	X	X	X
Sand eel (Ammodytidae)		X		X	X	X	X	X
Norway pout (Trisopterus esmarkii)		X		X	X	X	X	X
Blue Whiting (Micromesistius poutassou)		X		X	X	X	X	X
Greater weever (Trachinus draco)		X		X	X	X	X	X
Molluscs (except Sepia)		X		X	X	X	X	X
Garfish (Belone belone)		X		X	X	X	X	X
Gray gurnard (Eutrigla gurnardus)		X		X	X	X	X	X
Argentine (Argentina spp.)				X	X	X	X	X
Sprat (Sprattus sprattus)		X		X	X	X	X	X
Eel (Anguilla Anguilla)			X	X	X	X	X	X
Common shrimp/Baltic shrimp (Crangon spp., Palaemon adspersus)			X	X	X	X	X	X
Mackerel (Scomber spp.)				X			X	X
Horse mackerel (Trachurus spp.)				X			X	X
Herring (Clupea harengus)				X			X	X
Northern shrimp (Pandalus borealis)						X	X	X
Common shrimp/Baltic shrimp (Crangon spp., Palaemon adspersus)					X		X	X
Whiting (Merlangius merlangus)							X	X
Norway lobster (Nephrops norvegicus)							X	X
All other marine organisms								X

ANNEX V TOWED GEARS: Regions 4, 5 and 6

A.Regions 4 and 5

Specie	Mesh size range (millimetres)
	20 to 39	40 to 64	≥ 65
	Minimum percentage of target species
	50 %	80 %	None
Bogue (Boops boops)	*	*	*
Sardine (Sardina pilchardus)	*	*	*
Mackerel (Scomber spp.)		*	*
Horse mackerel (Trachurus spp.)		*	*
All other marine organisms			*

B.Region 6

Species	Mesh size range (millimetres)
	45 to 50	≥ 100
	Minimum percentage of target species
	30 %	None
Shrimps (Penaeus subtilis, Penaeus brasiliensis, Xiphopenaeus kroyeri)	*	*
All other marine organisms		*

ANNEX VI

FIXED GEARS: Regions 1 and 2 Applicable only in ICES Divisions VIId and IIIa and in the North Sea. In ICES division VIIe the minimum size shall be 90 mm. In ICES divisions VIId and VIIe the minimum size shall be 110 mm. Catches of anglerfish (Lophius spp.) taken ICES Sub-areas VI and VII and retained on board in excess of 30 % of the total catch on board from those areas must be taken with a minimum mesh size of 250 mm or greater.

Species	Mesh
Species	10-30 mm	50-70 mm	90-99 mm	100-119 mm	120-219 mm	≥ 220 mm
Sardine (Sardina pilchardus)	*	*	*	*	*	*
Eel (Anguilla anguilla)	*	*	*	*	*	*
Sprat (Sprattus sprattus)	*	*	*	*	*	*
Horse mackerel (Trachurus spp.)		*	*	*	*	*
Herring (Clupea harengus)		*	*	*	*	*
Mackerel (Scomber spp.)		*	*	*	*	*
Red mullets (Mullidae)		*	*	*	*	*
Garfish (Belone spp.)		*	*	*	*	*
Sea bass (Dicentrarchus labrax)			*	*	*	*
Grey mullets (Mugilidae)			*	*	*	*
Lesser spotted dogfish (Scyliorhinus canicula)			*	*	*	*
Dab (Limanda limanda)			*	*	*	*
Haddock (Melanogrammus aeglefinus)				*	*	*
Whiting (Merlangius merlangus)			*	*	*	*
Flounder (Platichthys flesus)			*	*	*	*
Sole (Solea vulgaris)			*	*	*	*
Plaice (Pleuronectes platessa)				*	*	*
Cuttlefish (Sepia officinalis)				*	*	*
Cod (Gadus morhua)					*	*
Pollack (Pollachius pollachius)					*	*
Ling (Molva molva)					*	*
Saithe (Pollachius virens)					*	*
Hake (Merluccius merluccius)					*	*
Picked dogfish (Squalus acanthias)					*	*
Greater spotted dogfish (Scyliorhinus stellaris)					*	*
Megrim (Lepidorhombus spp.)					*	*
Lumpsucker (Cyclopterus lumpus)					*	*
All other marine organisms						*

ANNEX VII FIXED GEARS: Region 3

In ICES Divisions VIIIc and IX the minimum mesh size will be 60 mm. However, with effect from 31 December 1999, the minimum mesh size wull be 80 to 90 mm. Catches of anglerfish (Lophius spp.) and retained on board in excess of 30 % of the total catch on board must be taken with minimum mes size of 220 mm or greater.

Mesh sizeSpecies	< 40 mm	40 to 49 mm	50 to 59 mm	60 to 79 mm	80 to 99 mm	≥ 100 mm
Sardine (Sardina pilchardus)	×	×	×	×	×	×
Shrimps (Palaemon spp.)	×	×	×	×	×	×
Rainbow wrasse (Coris julis)	×	×	×	×	×	×
Bogue (Boops boops)	×	×	×	×	×	×
Shrimps (Penaeus spp.)		×	×	×	×	×
Mantis shrimps (Squilla mantis)		×	×	×	×	×
Red mullets (Mullidae)		×	×	×	×	×
Wedge sole (Dicologoglossa cuneata)		×	×	×	×	×
Wrasses (Labridae)		×	×	×	×	×
Horse mackerel (Trachurus spp.)			×	×	×	×
Mackerel (Scomber spp.)			×	×	×	×
Bib (Trisopterus luscus)			×	×	×	×
Cuttlefish (Sepia officinalis)			×	×	×	×
Gurnards (Triglidae)			×	×	×	×
Sea breams (Sparidae)				×	×	×
Rockfish (Scorpaenidae)				×	×	×
Eyed sole (Microchirus acevia)				×	×	×
Shortfinned squids (Ommatostrephidae)				×	×	×
Conger (Conger conger)				×	×	×
Forkbeard (Phycis spp.)				×	×	×
Brill (Scophtalmus rhombus)				×	×	×
Weevers (Trachinidae)				×	×	×
Picarels (Centracanthidae)				×	×	×
Sea bass (Dicentrarchus labrax)					×	×
Whiting (Merlangius merlangus)					×	×
Turbot (Psetta maxima)					×	×
Pollack (Pollachius pollachius)					×	×
Flounders (Pleuronectidae)					×	×
Sole (Solea vulgaris)						×
Hake (Merluccius merluccius)						×
All other marine organisms						×

ANNEX VIII Permitted combinations of mesh size ranges for Regions 1 and 2, except Skagerrak and Kattegat

Millimetres
< 16 + 16 to 31
16 to 31 + 32 to 54
16 to 31 + 70 to 79
16 to 31 + 80 to 99
16 to 31 + ≥ 100
32 to 54 + 70 to 79
32 to 54 + 80 to 99
32 to 54 + ≥ 100
70 to 79 + 80 to 99
70 to 79 + ≥ 100
80 to 99 + ≥ 100

ANNEX IX Permitted combinations of mesh size ranges for Region 3, except ICES Division IXa east of longitude 7o 23′ 48″ W

Millimetres
16 to 31 + 32 to 54
16 to 31 + ≥ 70
32 to 54 + ≥ 70
55 to 59 + ≥ 70
60-69 + ≥ 70

ANNEX X A.CONDITIONS FOR USE OF CERTAIN COMBINATIONS OF MESH SIZE IN REGIONS 1 AND 2, EXCEPT SKAGERRAK AND KATTEGAT 1.Mesh size combination: 16 to 31 mm + ≥ 100 mm The catch retained on board shall consist of at least 20 % of any mixture of shrimps and common prawns (Pandalus montagui, Crangon spp. and Palaemon spp.). 2.Mesh size combination: 32 to 54 mm + > = 100 mm The catch retained on board or landed shall consist of at least 20 % of any mixture of shrimps and prawns (Crangon spp., Pandalus spp., Palaemon spp., Parapenaeus longirostris);orthe catch retained on board or landed shall consist of at least 50 % of any mixture of those marine organisms indicated in Annex I as the target species for mesh sizes between 32 and 54 mm, with the exception of shrimps and prawns (Crangon spp., Pandalus spp., Palaemon spp., Parapenaeus longirostris) and of no more than 15 % of any mixture of the species marked in Annex I with the symbol "y". 3.Mesh size combination: 70 to 79 mm + > = 100 mm The catch retained on board or landed shall consist of at least 10 % of any mixture of those marine organisms indicated in Annex I as the target species for mesh sizes between 70 and 79 mm. 4.Mesh size combination: 80 to 99 mm + ≥ 100 mm The catch retained on board shall consist of at least 45 % of any mixture of those marine organisms indicated in Annex I as the target species for mesh sizes between 80 and 99 mm. B.CONDITIONS FOR USE OF CERTAIN COMBINATIONS OF MESH SIZE IN SKAGERRAK AND KATTEGAT Mesh size combination < = 89 mm + > = 90 mm The catch retained on board or landed shall consist of at least 10 % of any mixture of those marine organisms indicated in Annex IV as the target species for mesh sizes between 70 and 89 mm. ANNEX XI A.CONDITIONS FOR USE OF CERTAIN COMBINATIONS OF MESH SIZE IN REGION 3, EXCEPT ICES DIVISION IXa EAST OF LONGITUDE 7o 23′ 48″ W 1.Mesh size combination: 16 to 31 mm + > = 70 mm The catch retained on board or landed shall consist of at least 40 % of any mixture of shrimps (Pandalus montagui, Crangon spp. and Palaemon spp.) and swimming crab;orThe catch retained on board or landed shall consist of at least 70 % of any mixture of those marine organisms indicated in Annex II as the target species for mesh sizes between 16 and 31 mm, with the exception of shrimps (Pandalus montagui, Crangon spp. and Palaemon spp.) and swimming crab. 2.Mesh size combination: 32 to 54 mm + > = 70 mm The catch retained on board or landed shall consist of at least 70 % of any mixture of those marine organisms indicated in Annex II as the target species for mesh sizes between 32 and 54 mm, with the exception of shrimps and prawns (Pandalus spp., Crangon spp. and Palaermon spp.). 3.Mesh size combination: 55-59 mm + > = 70 mm The catch retained on board or landed shall consist of at least 20 % of any mixture of shrimps and prawns (Pandalus spp., Crangon spp., Palaemon spp., Aristeus antennatus, Aristaeomorpha foliacea, Parapenaeus longirostris);orThe catch retained on board or landed shall consist of at least 60 % of any mixture of those marine organisms indicated in Annex II as the target species for mesh sizes between 55 and 59 mm, with the exception of shrimps and prawns (Pandalus spp., Crangon spp., Palaemon spp., Aristeus antennatus, Aristaeomorpha foliacea, Parapenaeus longirostris). 4.Mesh size combination: 60 to 69 mm + > = 70 mm The catch retained on board or landed shall consist of at least 60 % of any mixture of those marine organisms indicated in Annex II as the target species for mesh sizes between 60 and 69 mm. B.CONDITIONS FOR USE OF CERTAIN COMBINATIONS OF MESH SIZE IN ICES DIVISION IXa EAST OF LONGITUDE 7o 23′ 48″ W Mesh size combination 40-54mm + > = 55 mm The catch retained on board or landed shall consist of at least 50 % of any mixture of those marine organisms indicated in Annex III as the target species for mesh sizes between 40 and 54 mm. ANNEX XII MINIMUM SIZES Total lenght (carapace length). 30 cm for industrial purposes only With effect from 1 January 2002 a carapace length of 87 mm shall apply. It is prohibited to land more than 15 %, in number, of swordfish below 25 kg, or 125 cm. However, the rules set out in Article 19(1), shall not apply to fish, up to 15 % in number of individuals, weighing between 3,2 and 6,4 kg, and caught accidentally. No minimum size will apply to horse mackerel (Trachurus picturatus) caught in waters adjacent to the Azores islands and under the sovereignty or jurisdiction of Portugal.

Species	Minimum size
Species	Regions 1 to 5, except Skagerrak/Kattegat	Skagerrak/Kattegat
Cod (Gadus morhua)	35 cm	30 cm
Haddock (Melanogrammus aeglefinus)	30 cm	27 cm
Saithe (Pollachius virens)	35 cm	30 cm
Pollack (Pollachius pollachius)	30 cm	—
Hake (Merluccius merluccius)	27 cm	30 cm
Megrim (Lepidorhombus spp.)	20 cm	25 cm
Sole (Solea spp.)	24 cm	24 cm
Plaice (Pleuronectes platessa)	27 cm	27 cm
Whiting (Merlangius merlangus)	27 cm	23 cm
Ling (Molva molva)	63 cm	—
Blue ling (Molva dipterygia)	70 cm	—
Bass (Dicentrarchus labrax)	36 cm	—
Norway lobster (Nephrops norvegicus)Norway lobster tails		130 (40) mm
Mackerel (Scomber spp.)		20 cm
Herring (Clupea harengus)	20 cm	18 cm
Horse mackerel (Trachurus spp.)	15 cm	15 cm
Sardine (Sardina pilchardus)	11 cm	—
Lobster (Homarus gammarus)	85 mm	220 (78) mm
Spinous spider crab (Maia squinado)	120 mm	—
Queen scallop (Chlamys spp.)	40 mm	—
Grooved carpetshell (Ruditapes decussatus)	40 mm	—
Carpetshell (Venerupis pullastra)	38 mm	—
Short-necked clam (Venerupis philippinarum)	35 mm
Clam (Venus verrucosa)	40 mm	—
Hard clam (Callista chione)	6 cm
Razor clam (Ensis spp)	10 cm
Surf clams (Spisula solida)	25 mm
Donax clams (Donax spp.)	25 mm
Bean solen (Pharus legumen)	65 mm
Whelk (Buccinum undatum)	45 mm	—
Octopus (Octopus Vulgaris)	Whole area except waters under sovereignty or jurisdiction of Region 5: 750 gramsWaters under sovereignty or jurisdiction of Region 5: 450 grams (gutted)
Swordfish (Xiphias gladius)	25 kg or 125 cm (lower mandible)
Bluefin tuna (Thunnus thynnus)	70 cm or 6,4 kg
Crawfish (Palinurus spp.)	95 mm
Deepwater rose shrimp (Parapenaeus longirostirs)	22 mm (carapace length)

Species	Minimum Size; Regions 1 to 5, except Skagerrak/Kattegat
Norway lobster (Nephrops norvegicus)	Whole area, except Region 3 and ICES VIa, VIIa: total length 85 mm, carapace length 25 mm
Norway lobster (Nephrops norvegicus)	ICES VIa, VIIa; Region 3: total length 70 mm, carapace length 20 mm
Norway lobster tails	Whole area, except Region 3 and ICES VIa, VIIa: 46 mm
Norway lobster tails	ICES VIa, VIIa; Regione 3: 37 mm
Mackerel (Scomber spp.)	Whole area, except North Sea: 20 cm
Mackerel (Scomber spp.)	North Sea: 30 cm
Anchovy (Engraulis encrasicolus)	Whole area, except ICES division IXa east of longitude 7° 23′ 48″ W: 12 cm or 90 individuals/kgICES division IXa east of longitude 7° 23′ 48″ W: 10 cm
Edible crab (Cancer pagarus)	Regions 1 and 2 north of 56o N: 140 mm
	Region 2 south of 56o N, except ICES Divisions VIId, e, f, and ICES Divisions IVb, c: 130 mm
	ICES Divisions IVb, c south of 56 oN: 130 mm, except for an area limited by a point at 53o28′22″ N, 0o09′24″ E, on the coast of England, a straight line joining this point with 53o28′22″ N, 0o22′24″ E, the 6 mile boundary of the United Kingdom, and a straight line connecting a point at 51o54′06″ N, 1o30′30″ E, with a point on the coast of England at 51o55′48″ N, 1o17′00″ E, where the minimum landing size shall be 115 mm
	ICES Divisions VIId, e, f: 140 mm
	Region 3: 130 mm
Scallop (Pecten maximus)	Whole area, except ICES VIIa north of 52o 30′ N VIId: 100 mm
Scallop (Pecten maximus)	ICES VIIa north of 52o 30′ N, VIId: 110 mm

ANNEX XII a

Minimum sizes for Region 9

Species	Minimum size: Region 9
Turbot (Psetta maxima)	45 cm

ANNEX XIII MEASUREMENT OF THE SIZE OF A MARINE ORGANISM 1. The size of any fish shall be measured, as shown in Figure 1, from the tip of the snout to the end of the tail fin. 2. The size of a Norway lobster shall be measured as shown in Figure 2: as the length of the carapace, parallel to the midline, from the back of either eye socket to the distal edge of the carapace, and/or, as the total length, from the tip of the rostrum to the rear end of the telson, not including the setae, and/or, in the case of detached Norway lobster tails: from the front edge of the first tail segment present to the rear end of the telson, not including the setae. The tail shall be measured flat, unstretched and on the dorsal side. 3. The size of a lobster or crawfish from Regions 1 to 5 except Skagerrak/Kattegat shall be measured as shown in Figure 3, as the length of the carapace, parallel to the midline, from the back of either eye socket to the distal edge of the carapace. 4. The size of a lobster from Skagerrak or Kattegat shall be measured as shown in Figure 3: as the length of the carapace, parallel to the midline, from the back of either eye socket to the distal edge of the carapace, and/or, as the total length, from the tip of the rostrum to the rear end of the telson, not including the setae. 5. (a)The size of a spinous spider crab shall be measured, as shown in Figure 4A, as the length of the carapace, along the midline, from the edge of the carapace between the rostrums to the posterior edge of the carapace. (b)The size of an edible crab shall be measured, as shown in Figure 4B as the maximum width of the carapace measured perpendicular to the antero-posterior midline of the carapace. 6. The size of any bivalve mollusc shall be measured as shown in Figure 5, across the longest part of the shell. 7. The size of a whelk shall be measured as shown in Figure 6 as the length of the shell. 8. The size of a crawfish shall be measured as shown in Figure 7 as the length of the carapace from the tip of the rostrum to the midpoint of the distal edge of the carapace. 01998R0850-20140101_en_img_1

(a)Carapace length (b)Overall length 01998R0850-20140101_en_img_4

ANNEX XIV VERNACULAR AND SCIENTIFIC NAMES

VERNACULAR NAME	SCIENTIFIC NAME
Aesop shrimp	Pandalus montagui
Anchovy	Engraulis encrasicolus
Anglers	Lophiidae
Argentines	Argentinidae
Baltic shrimp	Palaemon adspersus
Bib	Trisopterus luscus
Bigeye tuna	Thunnus obesus
Bivalve molluscs	Bivalvia
Blue and red shrimp	Aristeus antennatus
Blue ling	Molva dipterygia
Blue whiting	Micromesistius poutassou
Bluefin tuna	Thunnus thynnus
Bogue	Boops boops
Breams	Bramidae, Berycidae
Brill	Scophthalmus rhombus
Carpetshell	Venerupis pullastra
Clam (= warty venus)	Venus verrucosa
Cod	Gadus morhua
Common mora	Mora moro
Common prawn	Pandalus spp.
Common shrimp	Crangon spp.
Conger	Conger conger
Crawfish	Palinurus spp.
Cuttlefish	Sepia officinalis, Sepia spp.
Dap	Limanda limanda
Deeptwater rose shrimp	Parapenaeus longirostris
Dogfish, spotted dogfish	Scyliorhinidae
Donax clams	Donax spp.
Edible crab	Cancer pagurus
Eel	Anguilla anguilla
Eyed sole	Microchirus ocellatus
Flounder	Platichthys flesus
Flounders	Pleuronectidae
Forkbeard	Phycis spp.
Garfish	Belone spp.
Gastropod molluscs	Gastropoda
Giant red shrimp	Aristaeomorpha foliacea
Grenadiers	Malacocephalus spp., Nezumia spp., Trachyrhynchus spp.
Grey mullets	Mugilidae
Grey gurnard	Eutrigla gurnardus
Grooved carpetshell	Ruditapes decussatus
Gurnards	Triglidae
Haddock	Melanogrammus aeglefinus
Hagfish	Myxinidae
Hairtails	Trichiuridae
Hake	Merluccius merluccius
Hard clam	Mercenaria mercenaria
Herring	Clupea harengus
Horse mackerel	Trachurus spp.
John Dory	Zeus faber
Lampreys	Petromyzonidae
Lemon sole	Microstomus kitt
Ling	Molva molva
Lobster	Homarus gammarus
Lumpsucker, Lumpfish	Cyclopterus lumpus
Mackerel	Scomber spp., Scomber scombrus
Mantis shrimp	Squilla mantis
Megrim	Lepidorhombus spp.
Northern shrimp	Pandalus borealis
Norway lobster	Nephrops norvegicus
Norway pout	Trisopterus esmarkii
Octopus	Octopus vulgaris, Eledone cirrosa
Picarels	Centracanthidae
Picked dogfish, Spurdog	Squalus acanthias spp.
Pilchard (= sardine)	Sardina pilchardus
Plaice	Pleuronectes platessa
Pollack	Pollachius pollachius
Poor cod	Trisopterus minutus
Pouting	Trisopterus luscus
Prawn	Palaemon spp.
Queen scallop	Chlamys opercularis
Rainbow wrasse	Coris juris
Razor clam	Ensis spp., Pharus legumen
Redband fish	Cepolidae
Red mullets	Mullidae
Rockfish	Scorpaenidae
Saithe	Pollachius virens
Salmon	Salmo salar
Salmonids	Salmonidae
Sand eels	Ammodytidae
Sardine (= pilchard)	Sardina pilchardus
Scallop	Pecten maximus
Sea bass	Dicentrarchus labrax
Sea breams	Sparidae
Sea trout	Salmo trutta
Shortnecked clam	Ruditapes philipinarum
Shrimp	Penaeus spp.
Silvery cod	Gadus argenteus
Skates and rays	Rajidae
Skipjack tuna	Katsuwonus pelamis
Smelt	Atherina spp., Osmerus spp.
Sole	Solea solea/vulgaris
Spinous spider crab	Maja squinado
Spotted flounder	Citharus linguatula
Sprat	Sprattus sprattus
Squat lobsters	Galatheidae
Squids	Loliginidae, Ommastrephidae, Alloteuthis spp.
Surf clam	Spisula solidissima
Swimming crab	Polybius henslowi
Swordfish	Xiphias gladius
Thickback sole	Microchirus variegatus
Tuna	Auxis spp., Euthynnus spp., Katsuwonus spp., Thunnus spp.
Turbot	Psetta maxima
Variegated scallop	Chlamys varia
Warty venus (= clam)	Venus verrucosa
Wedge sole	Dicologoglossa cuneata
Weevers	Trachinidae
Whelk	Buccinum undatum
Whiting	Merlangius merlangus
Witch	Glyptocephalus cynoglossus
Wrasses	Laridae
Yellowfin tuna	Thunnus albacares
Boarfish	Capros aper
Greater forkbeard	Phycis blennoides
Redfish	Sebastes spp.
Sardinelles	Sardinella aurita

ANNEX XIVa SPECIFICATIONS FOR A SORTING GRID 1.The species selective grid shall be attached in trawls with full square mesh codend with a mesh size equal to or larger than 70 millimetres and smaller than 90 millimetres. The minimum length of the codend shall be 8 metres. It shall be prohibited to use any trawl with more than 100 square meshes in any circumference of the codend, excluding the joining or the selvedges. The square mesh codend is required only in Skagerrak and Kattegat. 2.The grid shall be rectangular. The bars of the grid shall be parallel to the longitudinal axis of the grid. The bar spacing of the grid shall not exceed 35 millimetres. It shall be permitted to use one or more hinges in order to facilitate its storage on the net drum. 3.The grid shall be mounted diagonally in the trawl, upwards and backwards, anywhere from just in front of the codend to the anterior end of the untapered section. All sides of the grid shall be attached to the trawl. 4.In the upper panel of the trawl there shall be an unblocked fish outlet in immediate connection to the upper side of the grid. The opening of the fish outlet shall have the same width in the posterior side as the width of the grid and shall be cut out to a tip in the anterior direction along mesh bars from both sides of the grid. 5.It shall be permitted to attach in front of the grid a funnel to lead the fish towards the trawl floor and grid. The minimum mesh size of the funnel shall be 70 millimetres. The minimum vertical opening of the guiding funnel towards the grid shall be 15 centimetres. The width of the guiding funnel towards the grid shall be the grid width. 01998R0850-20140101_en_img_9

Schematic illustration of a size and species selective trawl. Entering fish are led towards the trawl floor and grid via a leading funnel. Larger fish are then led out of the trawl by the grid while smaller fish and Norway lobster pass through the grid and enter the codend. The full square mesh codend enhances escapement of small fish and undersized Norway lobster. The square mesh codend shown in the diagram is required only in Skagerrak and Kattegat. ANNEX XIVb CONDITIONS FOR FISHERIES WITH CERTAIN TOWED GEARS AUTHORISED IN THE BAY OF BISCAY 1.Specifications of the top square mesh panel The panel shall be a rectangular section of netting. There shall be only one panel. The panel shall not be obstructed in any way by either internal or external attachments. 2.Location of the panel The panel shall be inserted into the middle of the top panel of the rear tapered section of the trawl, just in front of the untapered section constituted by the extension piece and the codend.The panel shall terminate not more than 12 meshes from the hand braided row of meshes between the extension piece and the rear tapered section of the trawl. 3.Size of the panel The length of the panel shall be at least 2 metres and the width of the panel at least 1 metre. 4.Netting of the panel The meshes shall have a minimum mesh opening of 100 millimetres. The meshes will be square meshes, i.e. all four sides of the panel netting shall be cut all bars.The netting shall be mounted such that the bars run parallel and perpendicular to the longitudinal axis of the codend.The netting shall be single twine. The twine thickness shall be not more than 4 millimetres. 5.Insertion of the panel into the diamond mesh netting It shall be permitted to attach a selvedge on the four sides of the panel. The diameter of this selvedge shall be no more than 12 millimetres.The stretched length of the panel shall be equal to the stretched length of the diamond meshes attached to the longitudinal side of the panel.The number of diamond meshes of the top panel attached to the smallest side of the panel (i.e. one metre long side which is perpendicular to the longitudinal axis of the codend) shall be at least the number of full diamond meshes attached to the longitudinal side of the panel divided by 0,7. 6. The insertion of the panel into the trawl is illustrated below. 01998R0850-20140101_en_img_10

ANNEX XIVc SQUARE MESH PANEL FOR VESSELS OF MORE THAN 15 METRES 1.Specifications of the top square mesh panel The panel shall be a rectangular section of netting. The netting shall be single twine. The meshes shall be square meshes, i.e. all four sides of the panel netting shall be cut all bars. The mesh size shall be equal or more than 120 millimetres. The length of the panel shall be at least 3 metres except when incorporated into nets towed by vessels of less than 112 kW, when it shall be of at least 2 metres in length. 2.Location of the panel The panel shall be inserted into the top panel of the codend. The rearmost edge of the panel shall be no more than 12 metres from the codline as defined in Article 8 of Commission Regulation (EEC) No 3440/84 of 6 December 1984 on the attachment of devices to trawls, Danish seines and similar netsOJ L 318, 7.12.1984, p. 23.. 3.Insertion of the panel into the diamond mesh netting There shall be no more than two open diamond meshes between the longitudinal side of the panel and the adjacent selvedge.The stretched length of the panel shall be equal to the stretched length of the diamond meshes attached to the longitudinal side of the panel. The joining rate between the diamond meshes of the top panel of the codend and the smallest side of the panel shall be three diamond meshes to one square mesh for 80 millimetre codends, or two diamond meshes to one square mesh for 120 millimetre codends, except for edge bars of the panel from both sides. ANNEX XIVd SQUARE MESH PANEL FOR VESSELS OF LESS THAN 15 METRES 1.Specifications of the top square mesh panel The panel shall be a rectangular section of netting. The netting shall be single twine. The meshes shall be square meshes, i.e. all four sides of the panel netting shall be cut all bars. The mesh size shall be equal or more than 110 millimetres. The length of the panel shall be at least 3 metres except when incorporated into nets towed by vessels of less than 112 kW, when it shall be of at least 2 metres in length. 2.Location of the panel The panel shall be inserted into the top panel of the codend. The rearmost edge of the panel shall be no more than 12 metres from the codline as defined in Article 8 of Regulation (EEC) No 3440/84. 3.Insertion of the panel into the diamond mesh netting There shall be no more than two open diamond meshes between the longitudinal side of the panel and the adjacent selvedge. The stretched length of the panel shall be equal to the stretched length of the diamond meshes attached to the longitudinal side of the panel. The joining rate between the diamond meshes of the top panel of the codend and the smallest side of the panel shall be two diamond meshes to one square mesh, except for edge bars of the window from both sides. ANNEX XV CORRELATION TABLE

Regulation (EC) No 894/97	Present Regulation
Article 1	Article 1 and 2
Article 2(1)	Article 4
Article 2(2)	Article 10
Article 2(3)	Article 5
Article 2(4)	Article 14 and 15
Article 2(5)	—
Article 2(6), first subparagraph	Article 5(1) and Article 12(1)
Article 2(6), second subparagraph	Article 5(6)
Article 2(7)	—
Article 2(8)	—
Article 2(9), first subparagraph	Article 6
Article 2(9), second subparagraph	Article 7
Article 2(9), third subparagraph	Article 3(d)
Article 2(10), first subparagraph (a), (b) and (c)	Article 11(1)
Article 2(10), first subparagraph (d)	Article 3(g) and (h)
Article 2(10), first subparagraph (e)	Article 13
Article 2(10), second subparagraph	Article 48
Article 3	Article 48
Article 4	Article 16
Article 5(1)	Article 17 and Article 18(2)
Article 5(2)	Annex XIII
Article 5(3), first subparagraph	Article 19(1)
Article 5(3), second subparagraph (a)	Article 19(2)(b)
Article 5(3), second subparagraph (b), first and second indents	Article 19(2)(a)
Article 5(3), second subparagraph (b), third indent	Article 35
Article 5(3), second subparagraph (c)	Article 19(3)
Article 5(3), third subparagraph	Article 19(2)(a), third sentence
Article 5(4)	Article 18(3) and (4)
Article 5(5)	—
Article 6(1)	Article 26
Article 6(2)	Article 36
Article 7	Article 20
Article 8(1)	—
Article 8(2)	Article 21
Article 9	Article 22
Article 10(1)	—
Article 10(2)(a)	Article 30(1)
Article 10(2)(b)	Article 39
Article 10(3)	Article 29
Article 10(4)	Article 34(1), (2) and (3)
Article 10(5)	Article 34(4)
Article 10(6)	Article 29(6) and Article 34(5)
Article 10(7)	—
Article 10(8)	—
Article 10(9)	Article 37
Article 10(10)	Article 23
Article 10(11)	Article 28(2), Article 29(5), Article 30(2), second subparagraph, Article 30(3), Article 34(5), and Article 40
Article 10(12), first subparagraph	Article 31
Article 10(12), second subparagraph	Article 41
Article 10(13)	—
Article 10(14)	Article 30(1), last sentence
Article 10(15)	Article 28(1)
Article 10(16)	Article 32
Article 10(17)	Article 33
Article 10(18)	Article 38
Article 10(19)	Article 24(1)
Article 11	—
Article 12	Article 24(2)
Article 13	Article 42
Article 14	Article 43
Article 15	Article 44
Article 16	Article 45
Article 17	Article 46
Article 18	Article 48
Article 19	Article 49
Article 20	Article 50
Annex I	Annexes I, II, III, IV and V
Annex II	Annex XII
Annex III	Annex XII
Annex IV	Annex XIII
Annex V	Annex VI
Annex VI	Annex VII
Annex VII	Annex XV

May 26, 2001	ART24	Repeal
May 26, 2001	ART41	Repeal
May 26, 2001	ANN12	Amendment
May 26, 2001	ART33	Repeal

Council Regulation (EC) No 850/98 of 30 March 1998 for the conservation of fishery resources through technical measures for the protection of juveniles of marine organisms

Modified by

Council Regulation (EC) No 973/2001 of 14 May 2001 laying down certain technical measures for the conservation of certain stocks of highly migratory species