Article 1This Directive shall apply to tractors as defined in Article 1 of Directive 74/150/EEC having the following characteristics:ground clearance of not more than 600 mm beneath the lowest points of the front and rear axles, allowing for the differential,fixed or adjustable minimum track width with one of the axles less than 1150 mm fitted with tyres of a larger size. It is assumed that the axle mounted with the wider types is set at a track width of not more than 1150 mm. It must be possible to set the track width of the other axle in such a way that the outer edges of the narrower tyres do not go beyond the outer edges of the tyres of the other axle. Where the two axles are fitted with rims and tyres of the same size, the fixed or adjustable track width of the two axles must be less than 1150 mm,mass of 600 and 3000 kilograms, corresponding to the unladen weight of the tractor as defined in section 2.4 of Annex I to Directive 74/150/EEC, including the roll-over protection structure fitted in compliance with this Directive and tyres of the largest size recommended by the manufacturer.

Article 21.Each Member State shall grant component type-approval for any type of roll-over protection structure and its tractor attachment which satisfies the construction and testing requirements laid down in Annexes I to IV.2.A Member State which has granted EEC component type-approval shall take the measures required to verify, in so far as is necessary and if need be in cooperation with the competent authorities in the other Member States, that production models conform to the approved type. Such verification shall be limited to spot checks.

Article 3Member States shall, for each type of roll-over protection structure and its tractor attachment which they approve pursuant to Article 2, issue to the manufacturer of the tractor or of the roll-over protection structure, or to his authorized representative, an EEC component type-approval mark conforming to the model shown in Annex VII.Member States shall take all appropriate measures to prevent the use of marks liable to create confusion between roll-over protection structures which have been component type-approved pursuant to Article 2 and other devices.

Article 41.No Member State may prohibit the placing on the market of roll-over protection structures or their tractor attachments on grounds relating to their construction if they bear the EEC component type-approval mark.2.Nevertheless, a Member State may prohibit the placing on the market of roll-over protection structures bearing the EEC component type-approval mark which fail to conform to the approved type.That State shall forthwith inform the other Member States and the Commission of the measures taken, specifying the reasons for its decision.

Article 5The competent authorities of each Member State shall within one month send to the competent authorities of the other Member States copies of the component type-approval certificate, an example of which is given in Annex VIII, completed for each type of roll-over protection structure which they approve or refuse to approve.

Article 61.If the Member State which has granted EEC component type-approval finds that a number of roll-over protection structures and their tractor attachments bearing the same EEC component type-approval mark do not conform to the type which it has approved, it shall take the necessary measures to ensure that production models conform to the approved type. The competent authorities of that State shall advise those of the other Member States of the measures taken which may, where there is serious and repeated failure to conform, extend to withdrawal of EEC component type-approval. The said authorities shall take the same measures if they are informed by the competent authorities of another Member State of such failure to conform.2.The competent authorities of the Member States shall within one month inform each other of any withdrawal of EEC component type-approval and of the reasons for any such measure.

Article 7Any decision taken pursuant to the provisions adopted in implementation of this Directive to refuse or withdraw component type-approval for roll-over protection structures and their tractor attachments, or to prohibit their placing on the market or their use, shall set out in detail the reasons on which it is based. Such decision shall be notified to the party concerned, who shall at the same time be informed of the remedies available to him under the laws in force in the Member States and of the time limits allowed for the exercise of such remedies.

Article 8No Member State may refuse to grant EEC type-approval or national type-approval in respect of a tractor on grounds relating to the roll-over protection structure or its tractor attachment if these bear the EEC component type-approval mark and if the requirements laid down in Annex IX have been satisfied.

Article 91.No Member State may refuse or prohibit the sale, registration, entry into service or use of any tractor on grounds relating to the roll-over protection structure and its tractor attachment if these bear the EEC component type-approval mark and if the requirements laid down in Annex IX have been met.However, Member States may, in compliance with the Treaty, impose restrictions on the use of tractors referred to in this Directive in certain areas where safety so dictates, owing to the specific nature of certain terrains or crops. Member States shall inform the Commission of any such restrictions before they are implemented and of the reasons for their adoption.2.This Directive shall not affect the right of Member States to specify — in due compliance with the Treaty — the requirements they deem necessary to ensure that workers are protected when using the tractors in question, provided this does not mean that the protection structures are modified in a way unspecified in this Directive.

Article 101.In connection with EEC type-approval, any tractor to which Article 1 refers must be fitted with a roll-over protection structure.2.The structure, referred to in paragraph 1, unless it is a rear-mounted protection structure, must comply with the requirements laid down in Annexes I to V to this Directive, or in Directives 77/536/EEC or 79/622/EEC.

Article 11Any amendments which are necessary in order to adapt the requirements of the Annexes to this Directive so as to take account of technical progress shall be adopted in accordance with the procedure laid down in Article 13 of Directive 74/150/EEC.

Article 12Within 18 months following notification of this Directive, the Council, acting on a proposal from the Commission, on the basis of the provisions of the Treaty, shall adopt a Directive supplementing this Directive with provisions introducing additional impact tests into the dynamic test procedure.

Article 131.Member States shall bring into force the provisions necessary to comply with this Directive within 24 months of its notificationThis Directive was notified to the Member States on 26 June 1987. and shall forthwith inform the Commission thereof.2.Member States shall communicate to the Commission the texts of the main provisions of national law which they adopt in the field covered by this Directive.

Article 14This Directive is addressed to the Member States.

nullANNEX ICONDITIONS FOR EEC COMPONENT TYPE-APPROVAL1.The definitions and requirements of point 1 of Code 6OECD standard code for the official testing of front mounted roll-over protective structures on narrow-track wheeled agricultural and forestry tractors. of OECD Decision C(2008) 128 of October 2008, with the exception of point 1.1 (Agricultural and forestry tractors), shall apply, reading as follows:"1.Definitions1.1[not applicable]1.2Rolling Over Protective Structure (ROPS)Roll-over protective structure (safety cab or frame), hereinafter called "protective structure", means the structure on a tractor the essential purpose of which is to avoid or limit risks to the driver resulting from roll-over of the tractor during normal use.The roll-over protective structure is characterized by the provision of space for a clearance zone large enough to protect the driver when seated either inside the envelope of the structure or within a space bounded by a series of straight lines from the outer edges of the structure to any part of the tractor that might come into contact with flat ground and that is capable of supporting the tractor in that position if the tractor overturns.1.3Track1.3.1Preliminary definition: median plane of the wheelThe median plane of the wheel is equidistant from the two planes containing the periphery of the rims at their outer edges.1.3.2Definition of trackThe vertical plane through the wheel axis intersects its median plane along a straight line which meets the supporting surface at one point. If A and B are the two points thus defined for the wheels on the same axle of the tractor, then the track width is the distance between points A and B. The track may be thus defined for both front and rear wheels. Where there are twin wheels, the track is the distance between two planes each being the median plane of the pairs of wheels.1.3.3Additional definition: median plane of the tractorTake the extreme positions of points A and B for the tractor rear axle, which gives the maximum possible value for the track. The vertical plane at right angles to the line AB at its centre point is the median plane of the tractor.1.4WheelbaseThe distance between the vertical planes passing through the two lines AB as defined above, one for the front wheels and one for the rear-wheels.1.5Determination of seat index point; seat location and adjustment for test1.5.1Seat index point (SIP)For extension tests to test reports that originally used seat reference point (SRP), the required measurements shall be made with reference to SRP instead of SIP and the use of SRP shall be clearly indicated (see Annex 1).The seat index point shall be determined in accordance with ISO 5353:19951.5.2Seat location and adjustment for test1.5.2.1where the inclination of the backrest and seat pan is adjustable, these must be adjusted so that the seat index point is in its rear uppermost position;1.5.2.2where the seat is equipped with suspension, the latter must be blocked at mid-travel, unless this is contrary to the instructions clearly laid down by the seat manufacturer;1.5.2.3where the position of the seat is adjustable only lengthwise and vertically, the longitudinal axis passing through the seat index point shall be parallel with the vertical longitudinal plane of the tractor passing through the centre of the steering wheel and not more than 100 mm from that plane.1.6Clearance zone1.6.1Reference vertical plane and lineThe clearance zone (Figure 6.1 in Annex II) is defined on the basis of a vertical reference plane and a reference line:1.6.1.1The reference plane is a vertical plane, generally longitudinal to the tractor and passing through the seat index point and the centre of the steering wheel. Normally the reference plane coincides with the longitudinal median plane of the tractor. This reference plane shall be assumed to move horizontally with the seat and steering wheel during loading but to remain perpendicular to the tractor or the floor of the roll-over protective structure.1.6.1.2The reference line is the line contained in the reference plane that passes through a point located 140 + ah rearward and 90 – av below the seat index point and the first point on the steering wheel rim that it intersects when brought to the horizontal.1.6.2Determination of the clearance zone for tractors with a non-reversible seatThe clearance zone for tractors with a non-reversible seat is defined in 1.6.2.1 to1.6.2.11 below and is bounded by the following planes, the tractor being on a horizontal surface, the seat, where adjustable, adjusted to its rear uppermost positionUsers are reminded that the seat index point is determined according to ISO 5353 and is a fixed point with respect to the tractor that does not move as the seat is adjusted away from the mid-position. For purposes of determining the clearance zone, the seat shall be placed in the rear and uppermost position., and the steering wheel, where adjustable, adjusted to the mid-position for seated driving:1.6.2.1two vertical planes 250 mm on either side of the reference plane, these vertical planes extending 300 mm upwards from the plane defined in 1.6.2.8 below and longitudinally at least 550 mm in front of the vertical plane perpendicular to the reference plane passing (210 – ah) mm in front of the seat index point;1.6.2.2two vertical planes 200 mm on either side of the reference plane, these vertical planes extending 300 mm upwards from the plane defined in 1.6.2.8 below and longitudinally from the surface defined in 1.6.2.11 below to the vertical plane perpendicular to the reference plane passing (210 – ah) mm in front of the seat index point;1.6.2.3an inclined plane perpendicular to the reference plane, parallel with and 400 mm above the reference line, extending backwards to the point where it intersects the vertical plane which is perpendicular to the reference plane and which passes through a point (140 + ah) mm rearward of the seat index point;1.6.2.4an inclined plane, perpendicular to the reference plane which meets the plane defined in 1.6.2.3 above at its rearmost edge and rests on the top of the seat back rest;1.6.2.5a vertical plane perpendicular to the reference plane, passing at least 40 mm forward of the steering wheel and at least 760 – ah forward of the seat index point;1.6.2.6a cylindrical surface with its axis perpendicular to the reference plane, having a radius of 150 mm and tangential to the planes defined in 1.6.2.3 and 1.6.2.5;1.6.2.7two parallel inclined planes passing through the upper edges of the planes defined in 1.6.2.1 above with the inclined plane on the side where the impact is applied no closer than 100 mm to the reference plane above the zone of clearance;1.6.2.8a horizontal plane passing through a point 90 – av below the seat index point;1.6.2.9two portions of the vertical plane perpendicular to the reference plane passing 210 – ah forward of the seat index point, both these part planes joining respectively the rearmost limits of the planes defined in 1.6.2.1 above to the foremost limits of the planes defined in 1.6.2.2 above;1.6.2.10two portions of the horizontal plane passing 300 mm above plane defined in 1.6.2.8 above, both these part planes joining respectively the uppermost limits of the vertical planes defined in 1.6.2.2 above to the lowermost limits of the oblique planes defined in 1.6.2.7 above;1.6.2.11a surface, curved if necessary, whose generating line is perpendicular to the reference plane and rests on the back of the seat backrest.1.6.3Determination of the clearance zone for tractors with a reversible driver’s positionFor tractors with a reversible driver’s position (reversible seat and steering wheel), the clearance zone is the envelope of the two clearance zones defined by the two different positions of the steering wheel and the seat.1.6.4Optional seats1.6.4.1In case of tractors that could be fitted with optional seats, the envelope comprising the seat index points of all options offered shall be used during the tests. The protective structure shall not enter the larger clearance zone which takes account of these different seat index points.1.6.4.2In the case where a new seat option is offered after the test has been performed, a determination shall be made to see whether the clearance zone around the new SIP falls within the envelope previously established. If it does not, a new test must be performed.1.7Permissible measurement tolerancesLinear dimensions± 3 mmexcept for—tyre deflection± 1 mm—structure deflection during horizontal loadings± 1 mm—height of fall of the pendulum block± 1 mmMasses± 1 %Forces± 2 %Angles± 2°1.8Symbols

ah	(mm)	Half of the horizontal seat adjustment
av	(mm)	Half of the vertical seat adjustment
B	(mm)	Minimum overall width of the tractor
Bb	(mm)	Maximum outer width of the protective structure
D	(mm)	Deflection of the structure at the point of impact (dynamic tests) or at the point of, and in line with, the load application (static tests)
D′	(mm)	Deflection of the structure for the calculated energy required
Ea	(J)	Strain energy absorbed at point when load is removed. Area contained within F-D curve
Ei	(J)	Strain energy absorbed. Area under F-D curve
E′i	(J)	Strain energy absorbed after additional loading following a crack or tear
E″i	(J)	Strain energy absorbed in overload test in the event of the load having been removed before starting this overload test. Area under F-D curve
Eil	(J)	Energy input to be absorbed during longitudinal loading
Eis	(J)	Energy input to be absorbed during side loading
F	(N)	Static load force
F′	(N)	Loading force for calculated energy required, corresponding to E′i
F-D		Force/deflection diagram
Fi	(N)	Force applied to rear hard fixture
Fmax	(N)	Maximum static load force occurring during loading, with the exception of the overload
Fv	(N)	Vertical crushing force
H	(mm)	Falling height of the pendulum block (dynamic tests)
H′	(mm)	Falling height of the pendulum block for additional test (dynamic tests)
I	(kg.m2)	Tractor reference moment of inertia about the centre line of the rear wheels, whatever the mass of these rear wheels may be
L	(mm)	Tractor reference wheelbase
M	(kg)	Tractor reference mass during strength tests, as defined in section 3.2.1.4 in Annex II"

----------------------

For extension tests to test reports that originally used seat reference point (SRP), the required measurements shall be made with reference to SRP instead of SIP and the use of SRP shall be clearly indicated (see Annex 1).Users are reminded that the seat index point is determined according to ISO 5353 and is a fixed point with respect to the tractor that does not move as the seat is adjusted away from the mid-position. For purposes of determining the clearance zone, the seat shall be placed in the rear and uppermost position.2.GENERAL REQUIREMENTS2.1.Every protection structure and its attachment to a tractor must be so designed and constructed as to fulfil the essential purpose laid down in section 1.1.2.2.This condition is considered to be fulfilled if the requirements of Annexes II, III and IV are complied with.3.APPLICATION FOR EEC COMPONENT TYPE-APPROVAL3.1.The application for EEC component type-approval with regard to the strength of a protection structure and the strength of its attachment to a tractor must be submitted by the tractor manufacturer or by the manufacturer of the protection structure or by their authorized representatives.3.2.The application must be accompanied by the undermentioned documents in triplicate and by the following particulars:a drawing, either to scale or with indication of the principal dimensions, showing the general arrangement of the protection structure. This drawing must, in particular, show details of the mounting components,photographs from side and front showing mounting details,a brief description of the protection structure, including type of construction, method of mounting on the tractor and, where necessary, details of cladding and interior padding,details of materials used in the structure and in the roll-over protection structure mountings (see Annex VI).3.3.A tractor representative of the tractor type for which the protection structure to be approved is intended must be submitted to the technical service responsible for conducting the component type-approval tests. This tractor must be equipped with the protection structure.Furthermore, the manufacturer must indicate the sizes of tyres fitting or able to fit the front and rear axles.3.4.The holder of EEC component type-approval may request its extension to other tractor types. The competent authority which has granted the original EEC component type-approval must grant the extension if the approved protection structure and the type(s) of tractor for which the extension is requested comply with the following conditions:the mass of the unballasted tractor, as defined in section 1.4 of Annex III, does not exceed by more than 5 % the reference mass used in the test;the method of attachment and the points of attachment to the tractor are identical,any components such as mudguards and bonnet which may provide support for the protection structure have identical strength and are identically situated with respect to the protection structure,the critical dimensions and the position of the seat and steering wheel relative to the protection structure, and the position relative to the protection structure of the points deemed rigid and taken into consideration for the purpose of verifying that the zone of clearance is protected, are such that the zone of clearance continues to be protected by the structure after the latter has undergone the deformation resulting from the various tests.4.MARKINGS4.1.Every protection structure conforming to the approved type must bear the following markings:4.1.1.The trade mark or name;4.1.2.A component type-approval mark conforming to the model in Annex VII;4.1.3.Serial number of the protection structure;4.1.4.Make and type(s) of tractor(s) for which the protection structure is intended.4.2.All these particulars must appear on a small plate.4.3.These markings must be visible, legible and indelible.ANNEX IITechnical requirementsThe technical requirements for the EC type-approval of roll-over protection structures mounted in front of the driver’s seat on narrow-track wheeled agricultural or forestry tractors shall be those set out in point 3 of Code 6OECD standard code for the official testing of front mounted roll-over protective structures on narrow-track wheeled agricultural and forestry tractors. of the OECD Decision C(2008) 128 of October 2008, with the exception of points 3.2.4 (Test report), 3.4.1 (Administrative extension), 3.5 (Labelling) and 3.7 (Seat belt anchorage performance), reading as follows:"3.RULES AND DIRECTIONS3.1Prior conditions for the strength tests3.1.1Completion of two preliminary testsThe protective structure may only be subjected to the strength tests if both the Lateral Stability Test and the Non-Continuous Rolling Test have been satisfactorily completed (see flow diagram as Figure 6.3).3.1.2Preparation for the preliminary tests3.1.2.1The tractor must be equipped with the protective structure in its safety position.3.1.2.2The tractor must be fitted with tyres having the greatest diameter indicated by the manufacturer and the smallest cross-section for tyres of that diameter. The tyres must not be liquid-ballasted and must be inflated to the pressure recommended for field work.3.1.2.3The rear wheels must be set to the narrowest track width; the front wheels must be set as closely as possible to the same track width. If it is possible to have two front track settings which differ equally from the narrowest rear track setting, the wider of these two front track settings must be selected.3.1.2.4All the tractor’s tanks must be filled or the liquids must be replaced by an equivalent mass in the corresponding position.3.1.2.5All attachments used in the series production shall be fixed to the tractor in the normal position.3.1.3Lateral stability test3.1.3.1The tractor, prepared as specified above, is placed on a horizontal plane so that the tractor front-axle pivot point or, in the case of an articulated tractor, the horizontal pivot point between the two axles can move freely.3.1.3.2Using a jack or a hoist, tilt the part of the tractor which is rigidly connected to the axle that bears more than 50 percent of the tractor’s weight, while constantly measuring the angle of inclination. This angle must be at least 38° at the moment when the tractor is resting in a state of unstable equilibrium on the wheels touching the ground. Perform the test once with the steering wheel turned to full right lock and once with the steering wheel turned to full left lock.3.1.4Non-continuous rolling test3.1.4.1General remarksThis test is intended to check whether a structure fitted to the tractor for the protection of the driver can satisfactorily prevent continuous roll-over of the tractor in the event of its overturning laterally on a slope with a gradient of 1 in 1,5 (Figure 6.4).Evidence of non-continuous rolling can be provided in accordance with one of the two methods described in 3.1.4.2 and 3.1.4.3.3.1.4.2Demonstration of non-continuous rolling behaviour by means of the overturning test3.1.4.2.1The overturning test must be carried out on a test slope at least four metres long (see Figure 6.4). The surface must be covered with an 18-cm layer of a material that, as measured in accordance with Standards ASAE S313.3 FEB1999 and ASAE EP542 FEB1999 relating to soil cone penetrometer, has a cone penetration index of:A = 235 ± 20orB = 335 ± 203.1.4.2.2The tractor (prepared as described in paragraph 3.1.2) is tilted laterally with zero initial speed. For this purpose, it is placed at the start of the test slope in such a way that the wheels on the downhill side rest on the slope and the tractor’s median plane is parallel with the contour lines. After striking the surface of the test slope, the tractor may lift itself from the surface by pivoting about the upper corner of the protective structure, but it must not roll over. It must fall back on the side which it first struck.3.1.4.3Demonstration of non-continuous rolling behaviour by calculation3.1.4.3.1For the purpose of verifying non-continuous rolling behaviour by calculation, the following characteristic tractor data must be ascertained (see Figure 6.5):

B0	(m)	Rear tyre width
B6	(m)	Width of protective structure between the right and left points of impact
B7	(m)	Width of engine bonnet
D0	(rad)	Front-axle swing angle from zero position to end of travel
D2	(m)	Height of front tyres under full axle load
D3	(m)	Height of rear tyres under full axle load
H0	(m)	Height of the front-axle pivot point
H1	(m)	Height of centre of gravity
H6	(m)	Height at the point of impact
H7	(m)	Height of engine bonnet
L2	(m)	Horizontal distance between the centre of gravity and front axle
L3	(m)	Horizontal distance between the centre of gravity and rear axle
L6	(m)	Horizontal distance between the centre of gravity and the leading point of intersection of the protective structure (to be preceded by a minus sign if this point lies in front of the plane of the centre of gravity)
L7	(m)	Horizontal distance between the centre of gravity and the front corner of the engine bonnet
Mc	(kg)	Tractor mass used for calculation
Q	(kgm2)	Moment of inertia about the longitudinal axis through the centre of gravity
S	(m)	Rear track width

The sum of the track (S) and tyre (B0) widths must be greater than the width B6 of the protective structure.3.1.4.3.2For the purposes of calculation, the following simplifying assumptions can be made:3.1.4.3.2.1the stationary tractor overturns on a slope with a 1/1,5 gradient with a balanced front axle, as soon as the centre of gravity is vertically above the axis of rotation;3.1.4.3.2.2the axis of rotation is parallel to the tractor’s longitudinal axis and passes through the centre of the contact surfaces of the downhill front and rear wheel;3.1.4.3.2.3the tractor does not slide downhill;3.1.4.3.2.4impact on the slope is partly elastic, with a coefficient of elasticity of:U = 0,23.1.4.3.2.5the depth of penetration into the slope and the deformation of the protective structure together amount to:T = 0,2 m3.1.4.3.2.6no other components of the tractor penetrate into the slope.3.1.4.3.3The computer programme (BASICThe programme and the examples are available on the OECD website.) for determining the continuous or interrupted roll-over behaviour of a laterally overturning narrow-track tractor with a front-mounted roll-over protective structure is part of the present Code, with examples 6.1 to 6.11.3.1.5Measurement methods3.1.5.1Horizontal distances between the centre of gravity and rear (L3) or front (L2) axlesThe distance between the rear and front axles on both sides of the tractor shall be measured in order to verify there is no steering angle.The distances between the centre of gravity and the rear axle (L3) or the front axle (L2) shall be calculated from the mass distribution of the tractor between the rear and the front wheels.3.1.5.2Heights of rear (D3) and front (D2) tyresThe distance from the highest point of the tyre to the ground plane shall be measured (Figure 6.5), and the same method shall be used for the front and rear tyres.3.1.5.3Horizontal distance between the centre of gravity and the leading point of intersection of the protective structure (L6)The distance between the centre of gravity and the leading point of intersection of the protective structure shall be measured (Figures 6.6.a, 6.6.b and 6.6.c). If the protective structure is in front of the plane of the centre of gravity, the recorded measure will be preceded by a minus sign (–L6).3.1.5.4Width of the protective structure (B6)The distance between the right and left points of impact of the two vertical posts of the structure shall be measured.The point of impact is defined by the plane tangent to the protective structure passing through the line made by the top outer points of the front and rear tyres (Figure 6.7).3.1.5.5Height of the protective structure (H6)The vertical distance from the point of impact of the structure to the ground plane shall be measured.3.1.5.6Height of the engine bonnet (H7)The vertical distance from the point of impact of the engine bonnet to the ground plane shall be measured.The point of impact is defined by the plane tangent to the engine bonnet and the protective structure passing through the top outer points of the front tyre (Figure 6.7). The measurement shall be made on both sides of the engine bonnet.3.1.5.7Width of the engine bonnet (B7)The distance between the two points of impact of the engine bonnet as defined previously shall be measured.3.1.5.8Horizontal distance between the centre of gravity and the front corner of the engine bonnet (L7)The distance from the point of impact of the engine bonnet, as defined previously, to the centre of gravity shall be measured.3.1.5.9Height of the front-axle pivot point (H0)The vertical distance between the centre of the front-axle pivot point to the centre of axle of the front tyres (H01) shall be included in the manufacturer’s technical report and shall be checked.The vertical distance from the centre of the front tyres axle to the ground plane (H02) shall be measured (Figure 6.8).The height of the front-axle pivot (H0) is the sum of both previous values.3.1.5.10Rear track width (S)The minimum rear track width fitted with tyres of the largest size, as specified by the manufacturer, shall be measured (Figure 6.9).3.1.5.11Rear tyre width (B0)The distance between the outer and the inner vertical planes of a rear tyre in its upper part shall be measured (Figure 6.9).3.1.5.12Front axle swinging angle (D0)The largest angle defined by the swinging of the front axle from the horizontal position to the maximum deflection shall be measured on both sides of the axle, taking into account any end-stroke shock absorber. The maximum angle measured shall be used.3.1.5.13Tractor Mass (M)The tractor mass shall be determined according to the conditions specified in paragraph 3.2.1.4.3.2Conditions for testing the strength of protective structures and of their attachment to tractors3.2.1General requirements3.2.1.1Test purposesTests made using special rigs are intended to simulate such loads as are imposed on a protective structure, when the tractor overturns. These tests enable observations to be made on the strength of the protective structure and any brackets attaching it to the tractor and any parts of the tractor which transmit the test load.3.2.1.2Test methodsTests may be performed in accordance with the dynamic procedure or the static procedure. The two methods are deemed equivalent.3.2.1.3General rules governing preparation for tests3.2.1.3.1The protective structure must conform to the series production specifications. It shall be attached in accordance with the manufacturer’s recommended method to one of the tractors for which it is designed.Note: A complete tractor is not required for the static strength test; however, the protective structure and parts of the tractor to which it is attached represent an operating installation, hereinafter referred to as "the assembly".3.2.1.3.2For both the static test and the dynamic test the tractor as assembled (or the assembly) must be fitted with all series production components which may affect the strength of the protective structure or which may be necessary for the strength test.Components which may create a hazard in the clearance zone must also be fitted on the tractor (or the assembly) so that they may be examined to see whether the requirements of the Acceptance Conditions in 3.2.3 have been fulfilled.All components of the tractor or the protective structure including weather protective must be supplied or described on drawings.3.2.1.3.3For the strength tests, all panels and detachable non-structural components must be removed so that they may not contribute to the strengthening of the protective structure.3.2.1.3.4The track width must be adjusted so that the protective structure will, as far as possible, not be supported by the tyres during the strength tests. If these tests are conducted in accordance with the static procedure, the wheels may be removed.3.2.1.4Tractor reference mass during strength testsThe reference mass M, used in the formulae to calculate the height of the fall of the pendulum block, the loading energies and the crushing forces, must be at least the mass of the tractor, excluding optional accessories but including coolant, oils, fuel, tools plus the protective structure. Not included are optional front or rear weights, tyre ballast, mounted implements, mounted equipment or any specialised components.3.2.2Tests3.2.2.1Sequence of testsThe sequence of tests, without prejudice to the additional tests mentioned in sections 3.3.1.1.6, 3.3.1.1.7, 3.3.2.1.6 and 3.3.2.1.7, is as follows:1.impact (dynamic test) or loading (static test) at the rear of the structure(see 3.3.1.1.1 and 3.3.2.1.1);2.rear crushing test (dynamic or static test)(see 3.3.1.1.4 and 3.3.2.1.4);3.impact (dynamic test) or loading (static test) at the front of the structure(see 3.3.1.1.2 and 3.3.2.1.2);4.impact (dynamic test) or loading (static test) at the side of the structure(see 3.3.1.1.3 and 3.3.2.1.3);5.crushing at the front of the structure (dynamic or static test)(see 3.3.1.1.5 and 3.3.2.1.5).3.2.2.2General requirements3.2.2.2.1If, during the test, any part of the tractor restraining equipment breaks or moves, the test shall be restarted.3.2.2.2.2No repairs or adjustments of the tractor or protective structure may be carried out during the tests.3.2.2.2.3The tractor gear box shall be in neutral and the brakes off during the tests.3.2.2.2.4If the tractor is fitted with a suspension system between the tractor body and the wheels, it shall be blocked during the tests.3.2.2.2.5The side chosen for application of the first impact (dynamic test) or the first load (static test) on the rear of the structure shall be that which, in the opinion of the testing authorities, will result in the application of the series of impacts or loads under the most unfavourable conditions for the structure. The lateral impact or load and the rear impact or load shall be applied on both sides of the longitudinal median plane of the protective structure. The front impact or load shall be applied on the same side of the longitudinal median plane of the protective structure as the lateral impact or load.3.2.3Acceptance conditions3.2.3.1A protective structure is regarded as having satisfied the strength requirements if it fulfils the following conditions:3.2.3.1.1after each part-test it must be free from cracks or tears within the meaning of 3.3.1.2.1 or 3.2.3.1.2. If, during one of the tests, significant cracks or tears appear, an additional test, in accordance with dynamic tests or static tests, must be applied immediately after the impact or the crushing which caused cracks or tears to appear;3.2.3.1.2during the tests other than the overload test, no part of the protective structure must enter the clearance zone as defined in 1.6 in Annex I;3.2.3.1.3during the tests other than the overload test, all parts of the clearance zone shall be secured by the structure, in accordance with 3.3.1.2.2 and 3.3.2.2.2;3.2.3.1.4during the tests the protective structure must not impose any constraints on the seat structure;3.2.3.1.5the elastic deflection, measured in accordance with 3.3.1.2.3 and 3.3.2.2.3 shall be less than 250 mm.3.2.3.2There shall be no accessories presenting a hazard for the driver. There shall be no projecting part or accessory which is liable to injure the driver should the tractor overturn, or any accessory or part which is liable to trap him – for example by the leg or the foot – as a result of the deflections of the structure.3.2.4[not applicable]3.2.5Apparatus and equipment for dynamic tests3.2.5.1Pendulum block3.2.5.1.1A block acting as a pendulum must be suspended by two chains or wire ropes from pivot points not less than 6 m above the ground. Means must be provided for adjusting independently the suspended height of the block and the angle between the block and the supporting chains or wire ropes.3.2.5.1.2The mass of the pendulum block must be 2000 ± 20 kg excluding the mass of the chains or wire ropes which themselves must not exceed 100 kg. The length of the sides of the impact face must be 680 ± 20 mm (see Figure 6.10). The block must be filled in such a way that the position of its centre of gravity is constant and coincides with the geometrical centre of the parallelepiped.3.2.5.1.3The parallelepiped must be connected to the system which pulls it backwards by an instantaneous release mechanism which is so designed and located as to enable the pendulum block to be released without causing the parallelepiped to oscillate about its horizontal axis perpendicular to the pendulum’s plane of oscillation.3.2.5.2Pendulum supportsThe pendulum pivot points must be rigidly fixed so that their displacement in any direction does not exceed 1 per cent of the height of fall.3.2.5.3Lashings3.2.5.3.1Anchoring rails with the requisite track width and covering the necessary area for lashing the tractor in all the cases illustrated (see Figures 6.11, 6.12 and 6.13) must be rigidly attached to a non-yielding base beneath the pendulum.3.2.5.3.2The tractor shall be lashed to the rails by means of wire rope with round strand, fibre core, construction 6 × 19 in accordance with ISO 2408:2004 and a nominal diameter of 13 mm. The metal strands must have an ultimate tensile strength of 1770 MPa.3.2.5.3.3The central pivot of an articulated tractor shall be supported and lashed down as appropriate for all tests. For the lateral impact test, the pivot shall also be propped from the side opposite the impact. The front and rear wheels need not be in line if this facilitates the attachment of the wire ropes in the appropriate manner.3.2.5.4Wheel prop and beam3.2.5.4.1A softwood beam of 150 mm square shall be used as a prop for the wheels during the impact tests (see Figures 6.11, 6.12 and 6.13).3.2.5.4.2During the lateral impact tests, a softwood beam shall be clamped to the floor to brace the rim of the wheel opposite the side of impact (see Figure 6.13).3.2.5.5Props and lashings for articulated tractors3.2.5.5.1Additional props and lashings must be used for articulated tractors. Their purpose is to ensure that the section of the tractor on which the protective structure is fitted is as rigid as that of a non-articulated tractor.3.2.5.5.2Additional specific details are given in the section 3.3.1.1 for the impact and crushing tests.3.2.5.6Tyre pressures and deflections3.2.5.6.1The tractor tyres shall not be liquid-ballasted and shall be inflated to the pressures prescribed by the tractor manufacturer for field work.3.2.5.6.2The lashings shall be tensioned in each particular case such that the tyres undergo a deflection equal to 12 per cent of the tyre wall height (distance between the ground and the lowest point of the rim) before tensioning.3.2.5.7Crushing rigA rig as shown in Figure 6.14 shall be capable of exerting a downward force on a protective structure through a rigid beam approximately 250 mm wide connected to the load-applying mechanism by means of universal joints. Suitable axle stands shall be provided so that the tractor tyres do not bear the crushing force.3.2.5.8Measuring apparatusThe following measuring apparatus is needed:3.2.5.8.1device for measuring the elastic deflection (the difference between the maximum momentary deflection and the permanent deflection, (see Figure 6.15).3.2.5.8.2device for checking that the protective structure has not entered the clearance zone and that the latter has remained within the structure’s protective during the test (see section 3.3.2.2.2).3.2.6Apparatus and equipment for static tests3.2.6.1Static testing rig3.2.6.1.1The static testing rig must be designed in such a way as to permit thrusts or loads to be applied to the protective structure.3.2.6.1.2Provision must be made so that the load can be uniformly distributed normal to the direction of loading and along a flange having a length of one of the exact multiples of 50 between 250 and 700 mm. The stiff beam shall have a vertical face dimension of 150 mm. The edges of the beam in contact with the protective structure shall be curved with a maximum radius of 50 mm.3.2.6.1.3The pad shall be capable of being adjusted to any angle in relation to the load direction, in order to be able to follow the angular variations of the structure’s load-bearing surface as the structure deflects.3.2.6.1.4Direction of the force (deviation from horizontal and vertical):at start of test, under zero load: ± 2°,during test, under load: 10° above and 20° below the horizontal. These variations must be kept to a minimum.3.2.6.1.5The deflection rate shall be sufficiently slow, less than 5 mm/s so that the load may at all moments be considered as static.3.2.6.2Apparatus for measuring the energy absorbed by the structure3.2.6.2.1The force versus deflection curve shall be plotted in order to determine the energy absorbed by the structure. There is no need to measure the force and deflection at the point where the load is applied to the structure; however, force and deflection shall be measured simultaneously and co-linearly.3.2.6.2.2The point of origin of deflection measurements shall be selected so as to take account only of the energy absorbed by the structure and/or by the deflection of certain parts of the tractor. The energy absorbed by the deflection and/or the slipping of the anchoring must be ignored.3.2.6.3Means of anchoring the tractor to the ground3.2.6.3.1Anchoring rails with the requisite track width and covering the necessary area for anchoring the tractor in all the cases illustrated must be rigidly attached to a non-yielding base near the testing rig.3.2.6.3.2The tractor must be anchored to the rails by any suitable means (plates, wedges, wire ropes, jacks, etc.) so that it cannot move during the tests. This requirement shall be checked during the test, by means of the usual devices for measuring length.If the tractor moves, the entire test shall be repeated, unless the system for measuring the deflections taken into account for plotting the force versus deflection curve is connected to the tractor.3.2.6.4Crushing rigA rig as shown in Figure 6.14 shall be capable of exerting a downward force on a protective structure through a rigid beam approximately 250 mm wide, connected to the load-applying mechanism by means of universal joints. Suitable axle stands must be provided so that the tractor tyres do not bear the crushing force.3.2.6.5Other measuring apparatusThe following measuring devices are also needed:3.2.6.5.1device for measuring the elastic deflection (the difference between the maximum momentary deflection and the permanent deflection, (see Figure 6.15).3.2.6.5.2device for checking that the protective structure has not entered the clearance zone and that the latter has remained within the structure’s protective during the test (section 3.3.2.2.2).3.3Test procedures3.3.1Dynamic tests3.3.1.1Impact and crushing tests3.3.1.1.1Impact at the rear3.3.1.1.1.1The tractor shall be so placed in relation to the pendulum block that the block will strike the protective structure when the impact face of the block and the supporting chains or wire ropes are at an angle with the vertical plane A equal to M/100 with a 20° maximum, unless, during deflection, the protective structure at the point of contact forms a greater angle to the vertical. In this case the impact face of the block shall be adjusted by means of an additional support so that it is parallel to the protective structure at the point of impact at the moment of maximum deflection, the supporting chains or wire ropes remaining at the angle defined above.The suspended height of the block shall be adjusted and necessary steps taken so as to prevent the block from turning about the point of impact.The point of impact is that part of the protective structure likely to hit the ground first in a rearward overturning accident, normally the upper edge. The position of the centre of gravity of the block is 1/6 of the width of the top of the protective structure inwards from a vertical plan parallel to the median plane of the tractor touching the outside extremity of the top of the protective structure.If the structure is curved or protruding at this point, wedges enabling the impact to be applied thereon must be added, without thereby reinforcing the structure.3.3.1.1.1.2The tractor must be lashed to the ground by means of four wire ropes, one at each end of both axles, arranged as indicated in Figure 6.11. The spacing between the front and rear lashing points must be such that the wire ropes make an angle of less than 30° with the ground. The rear lashings must in addition be so arranged that the point of convergence of the two wire ropes is located in the vertical plane in which the centre of gravity of the pendulum block travels.The wire ropes must be tensioned so that the tyres undergo the deflections given in 3.2.5.6.2. With the wire ropes tensioned, the wedging beam shall be placed in front of and tight against the rear wheels and then fixed to the ground.3.3.1.1.1.3If the tractor is of the articulated type, the point of articulation shall, in addition, be supported by a wooden block at least 100 mm square and firmly lashed to the ground.3.3.1.1.1.4The pendulum block shall be pulled back so that the height of its centre of gravity above that at the point of impact is given by one of the following two formulae, to be chosen according to the reference mass of the assembly subjected to the tests:H = 25 + 0,07 Mfor tractor with a reference mass of less than 2000 kg;H = 125 + 0,02 Mfor tractor with a reference mass of more than 2000 kg.The pendulum block is then released and strikes the protective structure.3.3.1.1.1.5For tractors with a reversible driver’s position (reversible seat and steering wheel), the same formulae shall apply.3.3.1.1.2Impact at the front3.3.1.1.2.1The tractor shall be so placed in relation to the pendulum block that the block will strike the protective structure when the impact face of the block and the supporting chains or wire ropes are at an angle with the vertical plane A equal to M/100 with a 20° maximum, unless, during deflection, the protective structure at the point of contact forms a greater angle to the vertical. In this case the impact face of the block shall be adjusted by means of an additional support so that it is parallel to the protective structure at the point of impact at the moment of maximum deflection, the supporting chains or wire ropes remaining at the angle defined above.The suspended height of the pendulum block shall be adjusted and the necessary steps taken so as to prevent the block from turning about the point of impact.The point of impact is that part of the protective structure likely to hit the ground first if the tractor overturned sideways while travelling forward, normally the upper edge. The position of the centre of gravity of the block is 1/6 of the width of the top of the protective structure inwards from a vertical plane parallel to the median plane of the tractor touching the outside extremity of the top of the protective structure.If the structure is curved or protruding at this point, wedges enabling the impact to be applied thereon must be added, without thereby reinforcing the structure.3.3.1.1.2.2The tractor must be lashed to the ground by means of four wire ropes, one at each end of both axles, arranged as indicated in Figure 6.12. The spacing between the front and rear lashing points must be such that the wire ropes make an angle of less than 30° with the ground. The rear lashings shall in addition be so arranged that the point of convergence of the two wire ropes is located in the vertical plane in which the centre of gravity of the pendulum block travels.The wire ropes must be tensioned so that the tyres undergo the deflections given in 3.2.5.6.2. With the wire ropes tensioned, the wedging beam shall be placed behind and tight against the rear wheels and then fixed to the ground.3.3.1.1.2.3If the tractor is of the articulated type, the point of articulation shall, in addition, be supported by a wooden block at least 100 mm square and firmly lashed to the ground.3.3.1.1.2.4The pendulum block shall be pulled back so that the height of its centre of gravity above that at the point of impact is given by one of the following two formulae, to be chosen according to the reference mass of the assembly subjected to the tests:H = 25 + 0,07 Mfor tractor with a reference mass of less than 2000 kg.H = 125 + 0,02 Mfor tractor with a reference mass of more than 2000 kg.The pendulum block is then released and strikes the protective structure.3.3.1.1.2.5For tractors with a reversible driver’s position (reversible seat and steering wheel), the height shall be whichever is greater from the formula applied above and that selected below:H = 2,165 × 10-8 M × L2orH = 5,73 × 10-2I3.3.1.1.3Impact from the side3.3.1.1.3.1The tractor shall be so placed in relation to the pendulum block that the block will strike the protective structure when the impact face of the block and the supporting chains or wire ropes are vertical unless, during deflection, the protective structure at the point of contact forms an angle of less than 20° to the vertical. In this case the impact face of the block shall be adjusted by means of an additional support so that it is parallel to the protective structure at the point of impact at the moment of maximum deflection, the supporting chains or wire ropes remaining vertical on impact.The suspended height of the pendulum block shall be adjusted and necessary steps taken so as to prevent the block from turning about the point of impact.The point of impact shall be that part of the protective structure likely to hit the ground first in a sideways overturning accident.3.3.1.1.3.2The tractor wheels on the side which is to receive the impact must be lashed to the ground by means of wire ropes passing over the corresponding ends of the front and rear axles. The wire ropes must be tensioned to produce the tyre deflection values given in 3.2.5.6.2.With the wire ropes tensioned, the wedging beam shall be placed on the ground, pushed tight against the tyres on the side opposite that which is to receive the impact and then fixed to the ground. It may be necessary to use two beams or wedges if the outer sides of the front and rear tyres are not in the same vertical plane. The prop shall then be placed as indicated in Figure 6.13 against the rim of the most heavily loaded wheel opposite to the point of impact, pushed firmly against the rim and then fixed at its base. The length of the prop shall be such that it makes an angle of 30 ± 3° with the ground when in position against the rim. In addition, its thickness shall, if possible, be between 20 and 25 times less than its length and between 2 and 3 times less than its width. The props shall be shaped at both ends as shown in the details on Figure 6.13.3.3.1.1.3.3If the tractor is of the articulated type, the point of articulation shall in addition be supported by a wooden block at least 100 mm square and laterally supported by a device similar to the prop pushed against the rear wheel as in 3.3.1.1.3.2. The point of articulation shall then be lashed firmly to the ground.3.3.1.1.3.4The pendulum block shall be pulled back so that the height of its centre of gravity above that at the point of impact is given by one of the following two formulae, to be chosen according to the reference mass of the assembly subjected to the tests:H = (25 + 0,20 M) (B6+B) / 2Bfor tractor with a reference mass of less than 2000 kg.H = (125 + 0,15 M) (B6+B) / 2Bfor tractor with a reference mass of more than 2000 kg.3.3.1.1.3.5For reversible tractors, the height shall be whichever is greater of the results obtained from the formulae applicable above and below:H = 25 + 0,2 Mfor tractor with a reference mass of less than 2000 kg.H = 125 + 0,15 Mfor tractor with a reference mass of more than 2000 kg.The pendulum block is then released and strikes the protective structure.3.3.1.1.4Crushing at the rearThe beam shall be positioned over the rear uppermost structural member(s) and the resultant of crushing forces shall be located in the tractor’s median plane. A force Fv shall be applied where:Fv = 20 MThe force Fv shall be maintained for five seconds after cessation of any visually detectable movement of the protective structure.Where the rear part of the protective structure roof will not sustain the full crushing force, the force shall be applied until the roof is deflected to coincide with the plane joining the upper part of the protective structure with that part of the rear of the tractor capable of supporting the tractor when overturned.The force shall then be removed, and the crushing beam repositioned over that part of the protective structure which would support the tractor when completely overturned. The crushing force Fv shall then be applied again.3.3.1.1.5Crushing at the frontThe beam shall be positioned across the front uppermost structural member(s) and the resultant of crushing forces shall be located in the tractor’s median plane. A force Fv shall be applied where:Fv = 20 MThe force Fv shall be maintained for five seconds after the cessation of any visually detectable movement of the protective structure.Where the front part of the protective structure roof will not sustain the full crushing force, the force shall be applied until the roof is deflected to coincide with the plane joining the upper part of the protective structure with that part of the front of the tractor capable of supporting the tractor when overturned.The force shall then be removed, and the crushing beam repositioned over that part of the protective structure which would support the tractor when completely overturned. The crushing force Fv shall then be applied again.3.3.1.1.6Additional impact testsIf cracks or tears which cannot be considered negligible appear during an impact test, a second, similar test, but with a height of fall of:H′ = (H × 10-1) (12 + 4a) (1 + 2a)-1shall be performed immediately after the impact tests causing these tears or cracks to appear, "a" being the ratio of the permanent deformation (Dp) to the elastic deformation (De):a = Dp / Deas measured at the point of impact. The additional permanent deformation due to the second impact shall not exceed 30 per cent of the permanent deformation due to the first impact.In order to be able to carry out the additional test, it is necessary to measure the elastic deformation during all the impact tests.3.3.1.1.7Additional crushing testsIf during a crushing test, significant cracks or tears appear, a second, similar, crushing test, but with a force equal to 1,2 Fv shall be performed immediately after the crushing tests which caused these tears or cracks to appear.3.3.1.2Measurements to be made3.3.1.2.1Fractures and cracksAfter each test all structural members, joints and fastening systems shall be visually examined for fractures or cracks, any small cracks in unimportant parts being ignored.Any tears caused by the edges of the pendulum weight are to be ignored.3.3.1.2.2Clearance zone3.3.1.2.2.1Entry into the clearance zoneDuring each test the protective structure shall be examined to see whether any part of it has entered the clearance zone round the driving seat as defined in 1.6.Furthermore, the clearance zone shall not be outside the protection of the protective structure. For this purpose, it shall be considered to be outside the protection of the structure if any part of it would come in contact with flat ground if the tractor overturned towards the direction from which the test load is applied. For estimating this, the front and rear tyres and track width setting shall be the smallest standard fitting specified by the manufacturer.3.3.1.2.2.2Rear hard fixture testsIf the tractor is fitted with a rigid section, a housing or other hard fixture placed behind the driver’s seat, this fixture shall be regarded as a protective point, in the event of sideways or rear overturning. This hard fixture placed behind the driver’s seat shall be capable of withstanding, without breaking or entering the clearance zone, a downward force Fi where:Fi = 15 Mapplied perpendicularly to the top of the frame in the central plane of the tractor. The initial angle of application of force shall be 40° calculated from a parallel to the ground as shown in Figure 6.16. The minimum width of this rigid section shall be 500 mm (see Figure 6.17).In addition, it shall be sufficiently rigid and firmly attached to the rear of the tractor.3.3.1.2.3Elastic deflection (under side impact)The elastic deflection is measured (810 + av) mm above the index point, in the vertical plane passing through the point of impact. For this measurement, apparatus similar to that illustrated in Figure 6.15 shall be used.3.3.1.2.4Permanent deflectionAfter the final crushing test, the permanent deflection of the protective structure shall be recorded. For this purpose, before the start of the test, the position of the main roll-over protective structure members in relation to the seat index point shall be used.3.3.2Static tests3.3.2.1Loading and crushing tests3.3.2.1.1Loading at the rear3.3.2.1.1.1The load shall be applied horizontally in a vertical plane parallel to the tractor’s median plane.The load application point shall be that part of the roll-over protective structure likely to hit the ground first in a rearward overturning accident, normally the upper edge. The vertical plane in which the load is applied shall be located at a distance of 1/3 of the external width of the upper part of the structure from the median plane.If the structure is curved or protruding at this point, wedges enabling the load to be applied thereon shall be added, without thereby reinforcing the structure.3.3.2.1.1.2The assembly shall be lashed to the ground as described in 3.2.6.3.3.3.2.1.1.3The energy absorbed by the protective structure during the test shall be at least:Eil = 500 + 0,5 M3.3.2.1.1.4For tractors with a reversible driver’s position (reversible seat and steering wheel), the same formula shall apply.3.3.2.1.2Loading at the front3.3.2.1.2.1The load shall be applied horizontally, in a vertical plane parallel to the tractor’s median plane and located at a distance of 1/3 of the external width of the upper part of the structure.The load application point shall be that part of the roll-over protective structure likely to hit the ground first if the tractor overturned sideways while travelling forward, normally the upper edge.If the structure is curved or protruding at this point, wedges enabling the load to be applied thereon shall be added, without thereby reinforcing the structure.3.3.2.1.2.2The assembly shall be lashed to the ground as described in 3.2.6.3.3.3.2.1.2.3The energy absorbed by the protective structure during the test shall be at least:Eil = 500 + 0,5 M3.3.2.1.2.4For tractors with a reversible driver’s position (reversible seat and steering wheel), the energy shall be whichever is the higher of the above or either of the following as selected:Eil = 2,165 × 10–7M × L2orEil = 0,574 I3.3.2.1.3Loading from the side3.3.2.1.3.1The side loading shall be applied horizontally, in a vertical plane perpendicular to the tractor’s median plane. The load application point shall be that part of the roll-over protective structure likely to hit the ground first in a sideways overturning accident, normally the upper edge.3.3.2.1.3.2The assembly shall be lashed to the ground as described in 3.2.6.3.3.3.2.1.3.3The energy absorbed by the protective structure during the test shall be at least:Eis = 1,75 M(B6+B) / 2B3.3.2.1.3.4For tractors with a reversible driver’s position (reversible seat and steering wheel), the energy shall be whichever is higher of the above or the following:Eis = 1,75 M3.3.2.1.4Crushing at the rearAll provisions are identical to those given in 3.3.1.1.4.3.3.2.1.5Crushing at the frontAll provisions are identical to those given in 3.3.1.1.5.3.3.2.1.6Additional overload test (Figures 6.18 to 6.20)An overload test shall be carried out in all cases where the force decreases by more than 3 per cent during the last 5 per cent of the deflection reached when the energy required is absorbed by the structure (see Figure 6.19).The overload test involves the gradual increase of the horizontal load by increments of 5 per cent of the initial energy requirement up to a maximum of 20 per cent of energy added (see Figure 6.20).The overload test is satisfactory if, after each increase by 5, 10, or 15 per cent in the energy required, the force decreases by less than 3 per cent for a 5 per cent increment and remains greater than 0,8 Fmax.The overload test is satisfactory if, after the structure has absorbed 20 per cent of the added energy, the force exceeds 0,8 Fmax.Additional cracks or tears and/or entry into or lack of protective of the clearance zone due to elastic deflection are permitted during the overload test. However, after the removal of the load, the structure shall not enter the clearance zone, which shall be completely protected.3.3.2.1.7Additional crushing testsIf cracks or tears which cannot be considered as negligible appear during a crushing test, a second, similar crushing, but with a force of 1,2 Fv shall be applied immediately after the crushing test which caused the cracks or tears to appear.3.3.2.2Measurements to be made3.3.2.2.1Fractures and cracksAfter each test all structural members, joints and attachment systems shall be visually examined for fractures or cracks, any small cracks in unimportant parts being ignored.3.3.2.2.2Clearance zone3.3.2.2.2.1Entry into the clearance zoneDuring each test the protective structure shall be examined to see whether any part of it has entered the clearance zone as defined in 1.6 in Annex I.Furthermore, the clearance zone shall not be outside the protection of the protective structure. For this purpose, it shall be considered to be outside the protection of the structure if any part of it would come in contact with flat ground if the tractor overturned towards the direction from which the test load is applied. For estimating this, the front and rear tyres and track width setting shall be the smallest standard fitting specified by the manufacturer.3.3.2.2.2.2Rear hard fixture testsIf the tractor is fitted with a rigid section, a housing or other hard fixture placed behind the driver’s seat, this fixture shall be regarded as a protective point, in the event of sideways or rear overturning. This hard fixture placed behind the driver’s seat shall be capable of withstanding, without breaking or entering the clearance zone, a downward force Fi, where:Fi = 15 Mapplied perpendicularly to the top of the frame in the central plane of the tractor. The initial angle of application of force shall be 40° calculated from a parallel to the ground as shown in Figure 6.16. The minimum width of this rigid section shall be 500 mm (see Figure 6.17).In addition, it shall be sufficiently rigid and firmly attached to the rear of the tractor.3.3.2.2.3Elastic deflection under side loadingThe elastic deflection shall be measured (810+av) mm above the seat index point, in the vertical plane in which the load is applied. For this measurement, any apparatus similar to that illustrated in Figure 6.15 shall be used.3.3.2.2.4Permanent deflectionAfter the final crushing test the permanent deflection of the protective structure shall be recorded. For this purpose, before the start of the test, the position of the main roll-over protective structure members in relation to the seat index point shall be recorded.3.4Extension to other tractor models3.4.1[not applicable]3.4.2Technical extensionWhen technical modifications occur on the tractor, the protective structure or the method of attachment of the protective structure to the tractor, the testing station that has carried out the original test can issue a "technical extension report" if the tractor and protective structure satisfied preliminary tests of lateral stability and non-continuous rolling as defined in 3.1.3 and 3.1.4 and if the rear hard fixture as described in paragraph 3.3.1.2.2.2, when fitted, has been tested in accordance with the procedure described in this paragraph (except 3.4.2.2.4) in the following cases:3.4.2.1Extension of the structural test results to other models of tractorsThe impact or loading and crushing tests need not be carried out on each model of tractor, provided that the protective structure and tractor comply with the conditions referred to hereunder 3.4.2.1.1 to 3.4.2.1.5.3.4.2.1.1The structure (including rear hard fixture) shall be identical to the one tested;3.4.2.1.2The required energy shall not exceed the energy calculated for the original test by more than 5 per cent;3.4.2.1.3The method of attachment and the tractor components to which the attachment is made shall be identical;3.4.2.1.4Any components such as mudguards and bonnet that may provide support for the protective structure shall be identical;3.4.2.1.5The position and critical dimensions of the seat in the protective structure and the relative position of the protective structure on the tractor shall be such that the clearance zone would have remained within the protection of the deflected structure throughout all tests (this shall be checked by using the same reference of clearance zone as in the original test report, respectively Seat Reference Point [SRP] or Seat Index Point [SIP]).3.4.2.2Extension of the structural test results to modified models of the protective structureThis procedure has to be followed when the provisions of paragraph 3.4.2.1 are not fulfilled, it may not be used when the method of attachment of the protective structure to the tractor does not remain of the same principle (e.g. rubber supports replaced by a suspension device):3.4.2.2.1Modifications having no impact on the results of the initial test (e.g. weld attachment of the mounting plate of an accessory in a non-critical location on the structure), addition of seats with different SIP location in the protective structure (subject to checking that the new clearance zone(s) remain(s) within the protection of the deflected structure throughout all tests).3.4.2.2.2Modifications having a possible impact on the results of the original test without calling into question the acceptability of the protective structure (e.g. modification of a structural component, modification of the method of attachment of the protective structure to the tractor). A validation test can be carried out and the test results will be drafted in the extension report.The following limits for this type extension are fixed:3.4.2.2.2.1no more than 5 extensions may be accepted without a validation test;3.4.2.2.2.2the results of the validation test will be accepted for extension if all the acceptance conditions of the Code are fulfilled and:if the deflection measured after each impact test does not deviate from the deflection measured after each impact test in the original test report by more than ± 7 % (in the case of dynamic tests),if the force measured when the required energy level has been reached in the various horizontal load tests does not deviate from the force measured when the required energy has been reached in the original test by more than ± 7 % and the deflection measuredPermanent + elastic deflection measured at the point when the required energy level is obtained. when the required energy level has been reached in the various horizontal load tests does not deviate from the deflection measured when the required energy has been reached in the original test report by more than ± 7 % (in the case of static tests).3.4.2.2.2.3more than one protective structure modifications may be included in a single extension report if the represent different options of the same protective structure, but only one validation test can be accepted in a single extension report. The options not tested shall be described in a specific section of the extension report.3.4.2.2.3Increase of the reference mass declared by the manufacturer for a protective structure already tested. If the manufacturer wants to keep the same approval number it is possible to issue an extension report after having carried out a validation test (the limits of ± 7 % specified in 3.4.2.2.2.2 are not applicable in such a case).3.4.2.2.4Modification of the rear hard fixture or addition of a new rear hard fixture. It has to be checked that the clearance zone remains within the protection of the deflected structure throughout all test taking into account the new or modified rear hard fixture. A validation of the rear hard fixture consisting in the test described in 3.3.1.2.2.2 or 3.3.2.2.2.2 has to be carried out and the test results will be drafted in the extension report.3.5[not applicable]3.6Cold weather performance of protective structures3.6.1If the protective structure is claimed to have properties resistant to cold weather embrittlement, the manufacturer shall give details that shall be included in the report.3.6.2The following requirements and procedures are intended to provide strength and resistance to brittle fracture at reduced temperatures. It is suggested that the following minimum material requirements shall be met in judging the protective structure’s suitability at reduced operating temperatures in those countries requiring this additional operating protection.3.6.2.1Bolts and nuts used to attach the protective structure to the tractor and used to connect structural parts of the protective structure shall exhibit suitable controlled reduced temperature toughness properties.3.6.2.2All welding electrodes used in the fabrication of structural members and mounts shall be compatible with the protective structure material as given in 3.6.2.3 below.3.6.2.3Steel materials for structural members of the protective structure shall be of controlled toughness material exhibiting minimum Charpy V-Notch impact energy requirements as shown in Table 6.1. Steel grade and quality shall be specified in accordance with ISO 630:1995.Steel with an as-rolled thickness less than 2,5 mm and with a carbon content less than 0,2 per cent is considered to meet this requirement.Structural members of the protective structure made from materials other than steel shall have equivalent low temperature impact resistance.3.6.2.4When testing the Charpy V-Notch impact energy requirements, the specimen size shall be no less than the largest of the sizes stated in Table 6.1 that the material will permit.3.6.2.5The Charpy V-Notch tests shall be made in accordance with the procedure in ASTM A 370-1979, except for specimen sizes that shall be in accordance with the dimensions given in table 6.1.3.6.2.6Alternatives to this procedure are the use of killed or semi-killed steel for which an adequate specification shall be provided. Steel grade and quality shall be specified in accordance with ISO 630:1995, Amd 1:2003.3.6.2.7Specimens are to be longitudinal and taken from flat stock, tubular or structural sections before forming or welding for use in the protective structure. Specimens from tubular or structural sections are to be taken from the middle of the side of greatest dimension and shall not include welds.

Table 6.1Minimum Charpy V-notch impact energiesIndicates preferred size. Specimen size shall be no less than largest preferred size that the material permits.The energy requirement at – 20 °C is 2,5 times the value specified for – 30 °C. Other factors affect impact energy strength, i.e. direction of rolling, yield strength, grain orientation and welding. These factors shall be considered when selecting and using steel.

Specimen size	Energy at	Energy at
	–30 °C	–20 °C
mm	J	J
10 × 10	11	27,5
10 × 9	10	25
10 × 8	9,5	24
10 × 7,5	9,5	24
10 × 7	9	22,5
10 × 6,7	8,5	21
10 × 6	8	20
10 × 5	7,5	19
10 × 4	7	17,5
10 × 3,5	6	15
10 × 3	6	15
10 × 2,5	5,5	14

3.7[not applicable]Figure 6.1Clearance zone

Figure 6.1.aSide viewCross-section through the reference plane

Figure 6.1.bRear view

Figure 6.1.cView from above1 –Reference line2 –Seat index point3 –Reference planeFigure 6.2Clearance zone for tractors with reversible seat and steering wheelFigure 6.3Flow diagram for determining the continuous roll-over behaviour of a laterally overturning tractor with a front mounted roll-over protective structure (ROPS)Figure 6.4Rig for testing anti-roll properties on 1/1,5 gradientFigure 6.5Data required for calculating the overturn of a tractor with triaxial rolling behaviourFigures 6.6.a, 6.6.b, 6.6.cHorizontal distance between the centre of gravity and the leading point of intersection of the protective structure (L6)

Figure 6.7Determination of points of impact for measurement of width of protective structure (B6) and height of engine bonnet (H7)

Figure 6.8Height of the front-axle pivot point (H0)Figure 6.9Rear track width (S) and rear tyre width (B0)Figure 6.10Pendulum block and its suspending chains or wire ropesFigure 6.11Example of tractor lashing (rear impact)Figure 6.12Example of tractor lashing (front impact)Figure 6.13Example of tractor lashing (side impact)Figure 6.14Example of crushing rig of the tractorFigure 6.15Example of apparatus for measuring elastic deflectionFigure 6.16Simulated ground lineFigure 6.17Minimum width of the rear hard fixtureFigure 6.18Force/deflection curveOverload test not necessaryFigure 6.19Force/deflection curveOverload test necessaryFigure 6.20Force/deflection curveOverload test to be continued

----------------------

The programme and the examples are available on the OECD website.Permanent + elastic deflection measured at the point when the required energy level is obtained.Indicates preferred size. Specimen size shall be no less than largest preferred size that the material permits.The energy requirement at – 20 °C is 2,5 times the value specified for – 30 °C. Other factors affect impact energy strength, i.e. direction of rolling, yield strength, grain orientation and welding. These factors shall be considered when selecting and using steel.ANNEX IIICONDITIONS FOR TESTING THE STRENGTH OF PROTECTION STRUCTURES AND OF THEIR ATTACHMENT TO TRACTORS1.GENERAL REQUIREMENTS1.1.Test purposesTests made using special rigs are intended to simulate such loads as are imposed on a protection structure, when the tractor overturns. These tests, described in Annex IV, enable observations to be made on the strength of the protection structure and any brackets attaching it to the tractor and any parts of the tractor which transmit the test load.1.2.Test methodsTests may be performed in accordance with the dynamic procedure (see Annexes III A and IV A) or the static procedure (see Annexes III B and IV B), the choice being left to the manufacturer.The two methods are equivalent.1.3.General rules governing preparation for tests1.3.1.The protection structure must conform to the series production specifications. It must be attached in accordance with the manufacturer's recommended method to one of the tractors for which it is designed.A complete tractor is not required for the static strength test; however, the protection structure and parts of the tractor to which it is attached represent an operating installation, hereinafter referred to as "the assembly".1.3.2.For both the static test and the dynamic test the tractor as assembled must be fitted with all series production components which may affect the strength of the protection structure or which may be necessary for the strength test.Components which may create a hazard in the zone of clearance must also be fitted so that they may be examined to see whether the requirements of 3.1 and 3.2 of this Annex have been fulfilled.All components of the tractor or the protection structure including weather protection must be supplied or described on drawings.1.3.3.For the strength test, all panels and detachable non-structural components must be removed so that they may not contribute to the strengthening of the protection structure.1.3.4.Track widthThe track width must be adjusted so that the protection structure will as far as possible not be supported by the tyres during the strength tests. If these tests are conducted in accordance with the static procedure, it must be possible to remove the wheels.1.4.Tractor reference massThe reference mass mt, used in the formulae (see Annexes IV A and IV B) to calculate the height of the fall of the pendulum block, the loading energies and the crushing forces, must be at least that defined in section 2.4 of Annex I to Council Directive 74/150/EEC (i.e., excluding optional accessories but including coolant, oils, fuel, tools and driver) plus the protection structure and less 75 kilograms. Not included are optional front or rear weights, tyre ballast, mounted implements, mounted equipment or any specialized components.2.TESTS2.1.Sequence of testsThe sequence of tests is as follows, without prejudice to the additional tests mentioned in sections 1.6 of Annex IV A and 1.6/1.7 of Annex IV B:2.1.1.Impact (dynamic tests) or loading (static test) at the rear of the structure (see section 1.1 of Annexes IV A and IV B).2.1.2.Rear crushing test (dynamic or static tests) (see section 1.4 of Annexes IV A and IV B).2.1.3.Impact (dynamic tests) or loading (static tests) at the front of the structure (see section 1.2 of Annexes IV A and IV B).2.1.4.Impact (dynamic tests) or loading (static tests) at the side of the structure (see section 1.3 of Annexes IV A and IV B).2.1.5.Crushing at the front of the structure (dynamic or static tests) (see section 1.5 of Annexes IV A and IV B).2.2.General requirements2.2.1.If, during the test, any part of the restraining equipment breaks or moves, the test must be restarted.2.2.2.No repairs or adjustments of the tractor or protection structure may be carried out during the tests.2.2.3.The tractor gear box must be in neutral and the brakes off during the tests.2.2.4.If the tractor is fitted with a suspension system, between the tractor body and the wheels, it must be blocked during the tests.2.2.5.The side chosen for application of the first impact on the rear of the structure (in the case of dynamic tests) or the first load on the rear of the structure (in the case of static tests) must be that which, in the opinion of the testing authorities, will result in the application of the series of impacts or loads under the most unfavourable conditions for the structure. The side impact or load and the rear impact or load must be applied on both sides of the median longitudinal plane of the protection structure. The front impact or load must be applied on the same side of the median longitudinal plane of the protection structure as the side impact or load.2.3.Mesurement tolerances2.3.1.Linear dimensions: ± 3 mmexcept for:tyre deflection: ± 1 mm,structure deflection during horizontal loadings: ± 1 mm,each of the two measurements for the height of fall of the pendulum block: ± 1 mm2.3.2.Masses: ± 1 %2.3.3.Forces: ± 2 %2.3.4.Angles: ± 2 degrees.3.ACCEPTANCE CONDITIONS3.1.A protection structure submitted for EEC component type-approval is regarded as having satisfied the strength requirements if it fulfils the following conditions:3.1.1.After each part-test it must be free from cracks or tears within the meaning of section 3.1 of Annexes IV A and IV B. If, during one of the tests, significant cracks or tears appear, an additional test, in accordance with Annex IV A or Annex IV B must be applied immediately.3.1.2.During the tests, no part of the protection structure must enter the zone of clearance as defined in section 2 of Annexes IV A and IV B.3.1.3.During the tests no part of the zone of clearance must be outside the protection of the structure, in accordance with section 3.2 of Annexes IV A and IV B.3.1.4.The elastic deflection, measured in accordance with section 3.3 of Annexes IV and IV B, must be less than 250 mm.3.2.There must be no accessories presenting a hazard for the driver. There must be no projecting accessory or part which is liable to injure the driver should the tractor overturn, or any accessory or part which is liable to trap him — for example by the leg or the foot — as a result of the deflections of the structure.4.TEST REPORT4.1.The test report is attached to the EEC component type-approval certificate referred to in Annex VIII.The presentation of the report is as shown in Annex VI.The report must include:4.1.1.A general description of the protection structure's shape and construction (normally at least a scale of 1: 20 for the general drawings and 1: 2,5 for drawing of the attachments). The main dimensions must figure on the drawings; external dimensions of tractor with protection structure fitted; main interior dimensions and details of provisions for normal entry and exit and for escape where appropriate; and details of heating and ventilation system, where appropriate.4.1.3.A brief description of any interior padding.4.2.The report must identify clearly the tractor type (make, type, trade-name, etc.) used for testing and the types for which the protection structure is intended.4.3.If EEC component type-approval is being extended to other tractor types, the report must include the exact reference of the report of the original EEC component type-approval as well as precise indications regarding the requirements laid down in section 3.4 of Annex I.A.Apparatus and equipment for dynamic tests1.PENDULUM BLOCK1.1.A pendulum block must be suspended by two chains or wire ropes from pivot points not less than six metres above the ground. Means must be provided for adjusting independently the suspended height of the block and the angle between the block and the supporting chains or wire ropes.1.2.The mass must be 2000 ± 20 kilograms excluding the mass of the chains or wire ropes which themselves must not exceed 100 kilograms. The length of the sides of the impact face must be 680 ± 20 mm (see Figure 4, of Annex V). The block must be filled in such a way that the position of its centre of gravity is constant and coincides with the geometrical centre of the parallelepiped.1.3.The parallelepiped must be connected to the system which pulls it backwards by an instantaneous release mechanism which is so designed and located as to enable the pendulum block to be released without causing the parallelepiped to oscillate about its horizontal axis perpendicular to the pendulum's plane of oscillation.2.PENDULUM SUPPORTSThe pendulum pivot points must be rigidly fixed so that their displacement in any direction does not exceed 1 % of the height of fall.3.LASHINGS3.1.Anchoring rails with the requisite track width and covering the necessary area for lashing the tractor in all the cases illustrated (see Figures 5, 6, and 7, Annex V) must be rigidly attached to a non-yielding base beneath the pendulum.3.2.The tractor must be lashed to the rails by means of wire rope with round strand, fibre core, construction 6 × 19 in accordance with ISO 2408 and a nominal diameter of 13 mm. The metal strands must have an ultimate tensile strength of 1770 MPa.3.3.The central pivot of an articulated tractor must be supported and lashed down as appropriate for all tests. For the side impact test, the pivot must also be propped from the side opposite the impact. The front and rear wheels need not be in line if this facilitates the attachment of the wire ropes in the appropriate manner.4.WHEEL PROP AND BEAM4.1.A softwood beam of 150 mm square must be used as a prop for the wheels during the impact tests (see Figures 5, 6 and 7, Annex V).4.2.A softwood beam must be clamped to the floor to brace the rim of the wheel opposite the side impact as shown in Figure 7, Annex V.5.PROPS AND LASHINGS FOR ARTICULATED TRACTORS5.1.Additional props and lashings must be used for articulated tractors. Their purpose is to ensure that the section of the tractor on which the protection structure is fitted is as rigid as that of a rigid tractor.5.2.Additional specific details are given in Annex IV A for the impact and crushing tests.6.TYRE PRESSURES AND DEFLECTIONS6.1.The tractor tyres must not be liquid-ballasted and must be inflated to the pressures prescribed by the tractor manufacturer for field work.6.2.The lashings must be tensioned in each particular case that the tyres undergo a deflection equal to 12 % of the tyre wall height before tensioning.7.CRUSHING RIGA rig as shown in Figure 8, Annex V, must be capable of exerting a downward force on a protection structure through a rigid beam approximately 250 mm wide connected to the load-applying mechanism by means of universal joints. Suitable axle stands must be provided so that the tractor tyres do not bear the crushing force.8.MEASURING APPARATUS8.1.A device such as that illustrated in Annex V, Figure 9, for measuring the elastic deflection (the difference between the maximum momentary deflection and the permanent deflection).8.2.A device for checking that the protection structure has not entered the zone of clearance and that the latter has remained within the structure's protection during the test (see section 3.2 of Annex IV A).B.Apparatus and equipment for static tests1.STATIC TESTING RIG1.1.The static testing rig must be designed in such a way as to permit thrusts or "loads" to be applied to the protection structure.1.2.Provision must be made so that the load can be uniformly distributed normal to the direction of loading and along a flange having a length of one of the exact multiples of 50 between 250 and 700 mm. The stiff flange must have a vertical face dimension of 150 mm. The edges of the flange in contact with the protection structure must be curved with a maximum radius of 50 mm.1.3.The pad must be capable of being adjusted to any angle in relation to the load direction, in order to be able to follow the angular variations of the structure's load-bearing surface as the structure deflects.1.4.Direction of loading (deviation from horizontal and from vertical):at start of test, under zero load: ± 2°during test, under load: 10° above and 20° below the horizontal.These variations must be kept to a minimum.1.5.The deflection rate must be sufficiently slow (less than 5 mm/s) for the load at all moments to be considered as "static".2.APPARATUS FOR MEASURING THE ENERGY ABSORBED BY THE STRUCTURE2.1.The "force versus deflection" curve must be plotted in order to determine the energy absorbed by the structure. There is no need to measure the force and deflection at the point where the load is applied to the structure; however, "force" and "deflection" must be measured simultaneously and co-linearly.2.2.The point of origin of deflection measurements must be selected so as to take account only of the energy absorbed by the structure and/or by the deflection of certain parts of the tractor. The energy absorbed by the deflection and/or the slipping of the anchoring must be ignored.3.MEANS OF ANCHORING THE TRACTOR TO THE GROUND3.1.Anchoring rails with the requisite track width and covering the necessary area for anchoring the tractor in all the cases illustrated must be rigidly attached to a non-yielding base near the testing rig.3.2.The tractor must be anchored to the rails by any suitable means (plates, wedges, wire ropes, jacks, etc.) so that it cannot move during the tests. This requirement must be checked during the test, by means of the usual devices for measuring length.If the tractor moves, the entire test must be repeated, unless the system for measuring the deflections taken into account for plotting the "force versus deflection" curve is connected to the tractor.4.CRUSHING RIG4.1.A rig as shown in Figure 8 of Annex V must be capable of exerting a downward force on a protection structure through a rigid beam approximately 250 mm wide connected to the load-applying mechanism by means of universal joints. Suitable axle stand must be provided so that the tractor tyres do not bear crushing force.5.OTHER MEASURING APPARATUS5.1.A device such as that illustrated in Figure 9 of Annex V, for measuring the elastic deflection (the difference between the maximum momentary deflection and the permanent deflection).5.2.A device for checking that the protection structure has not entered the zone of clearance and that the latter has remained within the structure's protection during the test (see section 3.2 of Annex IV B).C.Symbolsmt (kg)tractor reference mass, as defined in section 1.4 of this Annex.D(mm)deflection of the structure at the point of impact (dynamic tests) or at the point of, and in line with, the load application (static tests).H(mm)falling height of the pendulum block.F (N) (Newton)static load force.Fmaxmaximum static load force occurring during loading, (N) with the exception of the overload.F′ (N)loading force corresponding to E′iF-Dforce/deflection diagram.Eis (J) (Joule)energy input to be absorbed during side loading.Eii (J)energy input to be absorbed during longitudinal loading.Fv (N)vertical crushing force.Ei (J)strain energy absorbed. Area under F-D curve (see Figure 10a, Annex V).E′i (J)strain energy absorbed after additional loading following a crack or tear (see Figures 10b and 10c, Annex V).Ea (J)strain energy absorbed at point when load is removed. Area contained within F-D curve (see Figure 10b, Annex V).E″i (J)strain energy absorbed in overload test in the event of the load having been removed before starting this overload test. Area under F-D curve (see Figure 10c, Annex V).ANNEX VFIGURES

Note:The configuration of the roll-over protection structure shown is solely for the purpose of illustration and for dimensional reference. It does not purport to denote design requirements.ANNEX VIMODELREPORT RELATING TO THE EEC COMPONENT TYPE-APPROVAL TEST OF A PROTECTION STRUCTURE (FRONT-MOUNTED BAR) WITH REGARD TO ITS STRENGTH AS WELL AS TO THE STRENGTH OF ITS ATTACHMENT TO THE TRACTORANNEX VIIMARKSThe EEC component type-approval mark consists of:a rectangle surrounding the lower case letter "e" followed by the distinguishing number of the Member State which has granted the component type-approval:1 for Germany, 2 for France, 3 for Italy, 4 for the Netherlands, 5 for Sweden, 6 for Belgium, 7 for Hungary, 8 for the Czech Republic, 9 for Spain, 11 for the United Kingdom, 12 for Austria, 13 for Luxembourg, 17 for Finland, 18 for Denmark, 19 for Romania, 20 for Poland, 21 for Portugal, 23 for Greece, 24 for Ireland, 25 for Croatia, 26 for Slovenia, 27 for Slovakia, 29 for Estonia, 32 for Latvia, 34 for Bulgaria, 36 for Lithuania, CY for Cyprus, MT for Malta,the EEC component type-approval number which corresponds to the number of the EEC component type-approval certificate issued with regard to the strength of the type of protection structure and its attachment to the tractor placed under and in the vicinity of the retangle,the letters V or SV, depending on whether a dynamic (V) or static (SV) test was conducted, followed by the number 2, indicating that this is a protection structure within the meaning of the Directive.EXAMPLE OF AN EEC COMPONENT TYPE-APPROVAL MARK

Legend:

The protection structure bearing the EEC component type-approval mark shown above is a structure of the bar type subjected to a dynamic test with two front-mounted uprights intended for a narrow-track tractor (V2), for which EEC component type-approval was granted in Belgium (e6) under the number 43.

ANNEX VIIIMODEL EEC COMPONENT TYPE-APPROVAL CERTIFICATEANNEX IXCONDITIONS FOR EEC TYPE-APPROVAL1.The application for EEC type-approval of a tractor with regard to the strength of a protection structure and the strength of its attachment to the tractor is submitted by the tractor manufacturer or by his authorized representative.2.A tractor representative of the tractor type to be approved, on which a protection structure and its attachment, duly approved, are mounted, must be submitted to the technical services responsible for conducting the type-approval tests.3.The technical service responsible for conducting the type-approval test checks whether the approved type of protection structure is intended to be mounted on the type of tractor for which the type-approval is requested. In particular, it must ascertain that the attachment of the protection structure corresponds to that which was used when the EEC component type-approval was granted.4.The holder of the EEC type-approval may ask for its extension for other types of protection structures.5.The competent authorities grant such extension on the following conditions:5.1.The new type of protection structure and its tractor attachment must have received EEC component type-approval.5.2.It is designed to be mounted on the type of tractor for which the extension of the EEC type-approval is requested.5.3.The attachment of the protection structure to the tractor must correspond to that which was tested when EEC component type-approval was granted.6.A certificate, of which a model is shown in Annex X, is annexed to the EEC type-approval certificate for each type-approval or type-approval extension which has been granted or refused.7.If the application for EEC type-approval for a type of tractor is introduced at the same time as the request for EEC component type-approval for a type of roll-over protection structure intended to be mounted on the type of tractor for which EEC type-approval is requested, the checks laid down in 2 and 3 are not applicable.ANNEX XMODEL

January 3, 1990	annex 4	Amendment
January 3, 1990	annex 6	Completion

Council Directive 87/402/EEC of 25 June 1987 on roll- over protection structures mounted in front of the driver's seat on narrow-track wheeled agricultural and forestry tractors

Modified by

Council Directive 89/681/EEC of 21 December 1989 amending directive 87/402/EEC on roll-over protection structures mounted in front of the driver's seat on narrow-track wheeled agricultural and forestry tractors